Alterations to the transyt-7F model to represent near-side transit stops

Transit vehicles stopping to load/unload passengers on-line at a signalized intersection can obstruct the flow of other vehicles. The TRANSYT model ignores the delay to other traffic caused by this loading/unloading process. This can cause TRANSYT to use incorrect flow profiles, resulting in signal timings that cater to these profiles rather than the actual ones. This paper describes a new model for representing near-side transit stops in lanes shared by public transit and private vehicles, and its implementation into the TRANSYT-7F program. The results of an initial application of the proposed model are also described. The proposed model, which is a deterministic simulation model, is able to represent the effect of near-side transit stops on the other traffic; this representation covers both total and partial blockage of the approaches during the transit loading. The procedure has been incorporated into the TRANSYT-7F program. This allows appropriate representation of the adverse effects of transit loading on-line during a green phase. It thus encourages the TRANSYT optimizer to push transit loading to the red phases.     

Microscopic simulation of transit operations: policy studies with the MISTRANSIT application programming interface

Abstract

Microscopic traffic simulators are the most advanced tools for representing the movement of vehicles on a transport network. However, the energy spent in traffic microsimulation has been mainly oriented to cars. Little interest has been devoted to more sophisticated models for simulating transit systems. Commercial software has some options to incorporate the operation of transit vehicles, but they are insufficient to properly consider a real public transport system. This paper develops an Application Programming Interface, called MIcroscopic Simulation of TRANSIT (MISTRANSIT), using the commercial microsimulator PARAllel MICroscopic Simulation. MISTRANSIT makes advances in three ways: public transport vehicles can have new characteristics; passengers are incorporated and traced as individual objects; and specific models represent the interaction between passengers and vehicles at stops. This paper presents the modelling approach as well as various experiments to illustrate the feasibility of MISTRANSIT for studying policy operations of transit systems.     

On the capacity of isolated, curbside bus stops

The maximal rates that buses can discharge from bus stops are examined. Models were developed to estimate these capacities for curbside stops that are isolated from the effects of traffic signals. The models account for key features of the stops, including their target service levels assigned to them by a transit agency. Among other things, the models predict that adding bus berths to a stop can sometimes return disproportionally high gains in capacity. This and other of our findings are at odds with information furnished in professional handbooks.     

An application of transyt for mixed car/streetcar operation

While the TRANSYT model for optimization of fixed-time traffic signals in a network of mixed transit and private vehicle traffic is well established, certain interactions between transit and nontransit vehicles are not properly modelled in TRANSYT. As a consequence, the optimal signal timing plan and network performance measures generated by TRANSYT may not be appropriate for the actual network. This paper briefly reviews a modelling procedure, adapted for use in the TRANSYT program, that goes some way toward overcoming TRANSYT's deficiencies in the representation of mixed traffic operation. The procedure is applied to a 6 kilometre corridor of mixed traffic operation in Toronto, Canada, to estimate the potential effects of incorporating streetcar operations in the optimization of fixed-time traffic signals.     

Ridership estimation procedure for a transit corridor with new bus rapid transit service

Ridership estimation is a critical step in the planning of a new transit route or change in service. Very often, when a new transit route is introduced, the existing routes will be modified, vehicle capacities changed, or service headways adjusted. This has made ridership forecasts for the new, existing, and modified routes challenging. This paper proposes and demonstrates a procedure that forecasts the ridership of all transit routes along a corridor when a new bus rapid transit (BRT) service is introduced and existing regular bus services are adjusted. The procedure uses demographic data along the corridor, a recent origin–destination survey data, and new and existing transit service features as inputs. It consists of two stages of transit assignment. In the first stage, a transit assignment is performed with the existing transit demand on the proposed BRT and existing bus routes, so that adjustments to the existing bus services can be identified. This transit assignment is performed iteratively until there is no adjustment in transit services. In the second stage, the transit assignment is carried out with the new BRT and adjusted regular bus services, but incorporates a potential growth in ridership because of the new BRT service. The final outputs of the procedure are ridership for all routes and route segments, boarding and alighting volumes at all stops, and a stop‐by‐stop trip matrix. The proposed ridership estimation procedure is applicable to a new BRT route with and without competing regular bus routes and with BRT vehicles traveling in dedicated lanes or in mixed traffic. The application of the proposed procedure is demonstrated via a case study along the Alameda Corridor in El Paso, Texas. Copyright © 2015 John Wiley & Sons, Ltd.     

Development of a transit network from a street map database with spatial analysis and dynamic segmentation

This paper presents an integrated transit-oriented travel demand modeling procedure within the framework of geographic information systems (GIS). Focusing on transit network development, this paper presents both the procedure and algorithm for automatically generating both link and line data for transit demand modeling from the conventional street network data using spatial analysis and dynamic segmentation. For this purpose, transit stop digitizing, topology and route system building, and the conversion of route and stop data into link and line data sets are performed. Using spatial analysis, such as the functionality to search arcs nearest from a given node, the nearest stops are identified along the associated links of the transit line, while the topological relation between links and line data sets can also be computed using dynamic segmentation. The advantage of this approach is that street map databases represented by a centerline can be directly used along with the existing legacy urban transportation planning systems (UTPS) type travel modeling packages and existing GIS without incurring the additional cost of purchasing a full-blown transportation GIS package. A small test network is adopted to demonstrate the process and the results. The authors anticipate that the procedure set forth in this paper will be useful to many cities and regional transit agencies in their transit demand modeling process within the integrated GIS-based computing environment.     

Electric vehicle park-charge-ride programs: A planning framework and case study in Chicago

In suburban areas, combining the use of electric vehicles (EV) and transit systems in an EV Park-Charge-Ride (PCR) approach can potentially help improve transit accessibility, facilitate EV charging and adoption, and reduce the need for long-distance driving and ensuing impacts. Despite the anticipated growth of EV adoption and charging demand, PCR programs are limited. With a focus on multi-modal trips, this study proposes a generic planning process that integrates EV infrastructure development with transit systems, develops a systematic assessment approach to fostering the PCR adoption, and illustrates a case implementation in Chicago. Specifically, this study develops a Suitability Index (SI) for EV charging locations at parking spots that are suitable for both EV charging and transit connections. SI can be customized for short-term and long-term planning scenarios. SI values are derived in Chicago as an example for (1) commuter rail stations (for work trips), and (2) shopping centers near transit stops as potential opportunities for additional weekday parking and EV charging (for multi-purpose trips/MPT). Furthermore, carbon emissions and vehicle miles travelled (VMT) across various travel modes and trip scenarios (i.e., work trips and MPT) are calculated. Compared to the baseline of driving a conventional vehicle, this study found that an EV PCR commuter can reduce up to 87% of personal VMT and 52% of carbon emissions. A more active role of the public sector in the PCR program development is recommended.     

Methods for pre-processing smartcard data to improve data quality

In recent years smartcards have been implemented in many transit systems around the world as a means by which passengers pay for travel. In addition to allowing speedier boardings there are many secondary benefits of smartcard systems including better understanding of travel patterns and behaviour of travellers. Such research is dependent on the smartcard correctly recording the boarding stop, and where available the alighting stop. It is also dependent on the smartcard system correctly aggregating individual rides into trips.This paper identifies causes for why smartcard systems may not correctly record such information. The first contribution of the paper is to propose a set of rules to aggregate individual rides into a single trip. This is critical in the research of activity based modelling as well as for correctly charging the passenger. The second contribution of the paper is to provide an approach to identify erroneous tap-out data, either caused by system problems or by the user. An approach to detecting this phenomenon is provided. The output from this analysis is then used to identify faulty vehicles or data supply using the “comparison against peers approach”. This third contribution of the paper identifies where transit agencies and operators should target resources to improve performance of their Automatic Vehicle Location systems. This method could also be used to identify users who appear to be tapping out too early.The approaches are tested using smartcard data from the Singapore public transport network from one week in April 2011. The results suggest that approximately 7.7% of all smartcard rides recorded the passenger as alighting one stop before the bus stop that they most probably alighted at. A further 0.7% of smartcard rides recorded the passenger as alighting more than one stop before the bus stop that they most probably alighted at. There was no evidence that smartcards overestimated the distance travelled by the passenger.     

Express guideway transit: A case for further development in transit automation

Safe and reliable coupling and decoupling of cars from a moving train is feasible with further developments in linear motor propulsion and control of transit vehicles. This allows the last car of a train to decouple and stop at a station for a relative long dwell time, before it accelerates and is coupled to a following train. Controlled doors in front and rear of the transit vehicle permit passengers to walk through the train to the car which stops at their destination. A proposed transit system using these features is described and compared to Bombardier's Advanced Rapid Transit. Potential advantages are high schedule speed, uncrowded trains, smaller and more stations, low energy requirements and a smaller vehicle fleet.     

Transit stop inspection and maintenance scheduling: A GPU accelerated metaheuristics approach

Bus stops are integral elements of a transit system and as such, their efficient inspection and maintenance is required, for proper and attractive transit operations. Nevertheless, spatial dispersion and the extensive number of bus stops, even for mid-size transit systems, complicates scheduling of inspection and maintenance tasks. In this context, the problem of scheduling transit stop inspection and maintenance activities (TSIMP) by a two-stage optimization approach, is formulated and discussed. In particular, the first stage involves districting of the bus stop locations into areas of responsibility for different inspection and maintenance crews (IMCs), while in the second stage, determination of the sequence of bus stops to be visited by an IMC is modelled as a vehicle routing problem. Given the complexity of proposed optimization models, advanced versions of different metaheuristic algorithms (Harmony Search and Ant Colony Optimization) are exploited and assessed as possible options for solving these models. Furthermore, two variants of ACO are implemented herein; one implemented into a CPU parallel computing environment along with an accelerated one by means of general-purpose graphics processing unit (GPGPU) computing. The model and algorithms are applied to the Athens (Greece) bus system, whose extensive number of transit stops (over 7500) offers a real-world test bed for assessing the potential of the proposed modelling approach and solution algorithms. As it was shown for the test example examined, both algorithms managed to achieve optimized solutions for the problem at hand while there were fund robust with respect to their algorithmic parameters. Furthermore, the use of graphics processing units (GPU) managed to reduce of computational time required.     

Integrated optimization of bus priority operations in connected vehicle environment

Most previous works associated with transit signal priority merely focus on the optimization of signal timings, ignoring both bus speed and dwell time at bus stops. This paper presents a novel approach to optimize the holding time at bus stops, signal timings, and bus speed to provide priority to buses at isolated intersections. The objective of the proposed model is to minimize the weighted average vehicle delays of the intersection, which includes both bus delay and impact on nearby intersection traffic, ensuring that buses clear these intersections without being stopped by a red light. A set of formulations are developed to explicitly capture the interaction between bus speed, bus holding time, and transit priority signal timings. Experimental analysis is used to show that the proposed model has minimal negative impacts on general traffic and outperforms the no priority, signal priority only, and signal priority with holding control strategies (no bus speed adjustment) in terms of reducing average bus delays and stops. A sensitivity analysis further demonstrates the potential of the proposed approach to be applied to bus priority control systems in real‐time under different traffic demands, bus stop locations, and maximum speed limits. Copyright © 2016 John Wiley & Sons, Ltd.     

Optimal control of headway variation on transit routes

Headway control strategies have been proposed as methods for correcting transit service irregularities and thereby reducing passenger wait times at stops. This paper addresses a particular strategy which can be implemented on high frequency routes (headways under 10–12 minutes), in which buses are held at a control stop to a threshold headway. An algorithm is developed which yields the optimal control stop location and optimal threshold headway with respect to a system wait function. The specification of the wait function is based on the development of several empirical models, including a headway variation model and an average delay time model at control stops. A conclusion is reached that the headway variation does not increase linearly along a route, a common assumption made in many previous studies. Furthermore, the location of the optimal control stop and threshold value are sensitive to the passenger boarding profile, as expected. The algorithm itself appears to have practical application to conventional transit operations.     

Mesoscopic simulation for transit operations

This paper presents a transit simulation model designed to support evaluation of operations, planning and control, especially in the context of Advanced Public Transportation Systems (APTS). Examples of potential applications include frequency determination, evaluation of real-time control strategies for schedule maintenance and assessing the effects of vehicle scheduling on the level of service. Unlike most previous efforts in this area, the simulation model is built on a platform of a mesoscopic traffic simulation model, which allows modeling of the operation dynamics of large-scale transit systems taking into account the stochasticity due to interactions with road traffic. The capabilities of Mezzo as an evaluation tool of transit operations are demonstrated with an application to a real-world high-demand bus line in the Tel-Aviv metropolitan area under various scenarios. The headway distributions at two stops are compared with field observations and show good consistency between simulated and observed data.     

Estimating bus run times for new limited-stop service using archived AVL and APC data

In recent years, several transit agencies have been trying to be more competitive with the automobile to attract choice riders. Transit agencies can only be competitive if they can provide services that are reliable, have a short access and egress time, and have run times that are comparable to automobiles. Several transit agencies try to be competitive through offering faster service, such as limited-stop (express) bus service. This study uses AVL and APC data, in addition to a disaggregate data obtained from a travel behavior survey, to select stops and estimate run times for a new limited-stop service that will run parallel to a heavily used bus route (67 Saint-Michel) in Montréal, Canada. Three different scenarios are developed based on theory and practice to select stops to be incorporated in the new limited service. The time savings for each scenario are then evaluated as a range and a fourth scenario is developed. A limited-stop service is recommended based on selecting stops serving both directions of the route, major activity points and stop spacing. This study shows that implementing a limited-stop service would yield substantial time savings for both, the new limited service and the existing regular service running in parallel.     

Analyzing urban bus service reliability at the stop, route, and network levels

Improving the reliability of bus service has the potential to increase the attractiveness of public transit to current and prospective riders. An understanding of service reliability is necessary to develop strategies that help transit agencies provide better services. However, few studies have been conducted analyzing bus reliability in the metropolis of China. This paper presents an in-depth analysis of service reliability based on bus operational characteristics in Beijing. Three performance parameters, punctuality index based on routes (PIR), deviation index based on stops (DIS), and evenness index based on stops (EIS), are proposed for the evaluation of bus service reliability. Reliability involves routes, stops, punctuality, deviation, and evenness. The relationship among the three parameters is discussed using a numerical example. Subsequently, through a sampling survey of bus lines in Beijing, service reliability at the stop, route, and network levels are estimated. The effects of route length, headway, the distance from the stop to the origin terminal, and the use of exclusive bus lanes are also analyzed. The results indicate low service reliability for buses in Beijing and a high correlation between service reliability and route length, headway, distance from the stop to the origin terminal, and the provision of exclusive bus lanes.     

Multi-modal traffic signal control with priority,signal actuation and coordination

Both coordinated-actuated signal control systems and signal priority control systems have been widely deployed for the last few decades. However, these two control systems are often conflicting with each due to different control objectives. This paper aims to address the conflicting issues between actuated-coordination and multi-modal priority control. Enabled by vehicle-to-infrastructure (v2i) communication in Connected Vehicle Systems, priority eligible vehicles, such as emergency vehicles, transit buses, commercial trucks, and pedestrians are able to send request for priority messages to a traffic signal controller when approaching a signalized intersection. It is likely that multiple vehicles and pedestrians will send requests such that there may be multiple active requests at the same time. A request-based mixed-integer linear program (MILP) is formulated that explicitly accommodate multiple priority requests from different modes of vehicles and pedestrians while simultaneously considering coordination and vehicle actuation. Signal coordination is achieved by integrating virtual coordination requests for priority in the formulation. A penalty is added to the objective function when the signal coordination is not fulfilled. This “soft” signal coordination allows the signal plan to adjust itself to serve multiple priority requests that may be from different modes. The priority-optimal signal timing is responsive to real-time actuations of non-priority demand by allowing phases to extend and gap out using traditional vehicle actuation logic. The proposed control method is compared with state-of-practice transit signal priority (TSP) both under the optimized signal timing plans using microscopic traffic simulation. The simulation experiments show that the proposed control model is able to reduce average bus delay, average pedestrian delay, and average passenger car delay, especially for highly congested condition with a high frequency of transit vehicle priority requests.     

Maximizing bus discharge flows from multi-berth stops by regulating exit maneuvers

Upon having loaded and unloaded their passengers, buses are often free to exit a multi-berth bus stop without delay. A bus need not wait to perform this exit maneuver, even if it requires circumventing one or more other buses that are still dwelling in the stop’s downstream berths. Yet, many jurisdictions impose restrictions on bus entry maneuvers into a stop to limit disruptions to cars and other buses. Buses are typically prohibited from entering a stop whenever this would require maneuvering around other buses still dwelling in upstream berths. An entering bus is instead required to wait in queue until the upstream berths are vacated.Analytical models are formulated to predict how bus discharge flows from busy, multi-berth stops are affected by allowing buses to freely exit, but not freely enter berths. These models apply when: a bus queue is always present at the stop’s entrance; buses depart the entry queue and enter the stop as per the restriction described above; and the stop is isolated from the effects of nearby traffic signals and other bus stops. We find that for these restricted-entry stops, bus-carrying capacities can often be improved by regulating the exit maneuvers as well. This turns out to be particularly true when the stop’s number of berths is large. Simulations show that these findings still hold when a stop is only moderately busy with entry queues that persist for much, but not all of the time. The simulations also indicate that removing any restrictions on bus exit maneuvers is almost always productive when stops are not busy, such that short entry queues form only on occasion, and only for short periods. We argue why certain simple policies for regulating exit maneuvers would likely enhance bus-stop discharge flows.     

Optimization of bus stop placement for routes on uneven topography

The improvement and expansion of public transport is an increasingly important solution to the high congestion costs and worsening environmental impacts of the car dominated transport systems seen in many cities today. The intelligent design of stop locations is one way to improve the quality of PT and thereby improve its ridership. Stop placement is a relatively complex task as it involves a trade-off between two competing goals; accessibility and operation; however this trade-off can be made explicit using an appropriate mathematical model. Many such models have been developed in the literature, however none consider the effects of uneven topography. Topography is an important but often neglected factor in the design of public transportation systems, with the potential to have a significant impact on the accessibility, operation and planning of a transit service. In this work a mathematical modelling approach to bus stop placement is developed which includes considerations of uneven topography in three ways; (1) Its effect on walking speed; (2) Its impact on the attractiveness of an access path to a transit service; and (3) Its effect on acceleration rates at stops. Because of the complexity of the model developed, a heuristic evolutionary algorithm’ is employed to approximate an optimal solution to the model. Finally, the model and solution method are applied to a case study in the Auckland CBD area in New Zealand.     

Effect of signal coordination on traffic emission

This study investigates the effect of traffic signal coordination on emissions and compares it with their effects on operational performance measures of delay and stops. Various platoon ratios are obtained by simulating cycle lengths and offsets. Our results indicate that the impact of the cycle length on delay is more significant than those on stops and emissions for under-saturation traffic conditions. Given a fixed cycle length, increasing the platoon ratio can reduce delay, stops, and emissions, with reduction in emissions being correlated with stops than delay. The effect on emissions from the platoon arrival with respect to the onset of green or red indication is identified. With the same cycle length and platoon ratio, the early arrival situation, when the leading vehicles of a platoon encounters the red signal, can generate more emissions than are associated with late platoon arrival, when the last few vehicles in a platoon are stopped at the intersection by the onset of the red signal.