共查询到18条相似文献,搜索用时 140 毫秒
1.
结合目前国内冰荷载研究现状,主要介绍了东营港某桩基工程的冰荷载类型、冰荷载计算方法及防冰设计方案,从施工难易程度、施工工期、投资造价等方面考虑,着重分析比较了预制挡冰裙和基桩外包钢皮这两种防冰措施的特点,并总结了海港工程防冰设计应注意的主要事项,供同类工程设计时参考、借鉴。 相似文献
2.
3.
冰荷载是冰区海洋平台设计的控制荷载,极值冰力直接危害着平台结构整体的安全。文章以渤海辽东湾导管架海洋平台为例,考虑了海洋平台结构抗冰设计的各种不确定性;基于Pushover方法,得到了海洋平台结构的简化力学模型,分析了极值冰荷载下海洋平台结构整体抗力以及极值响应;并且采用K-S检验法,对结构整体抗力及极值冰力响应的概率统计特性进行了分析。结果表明,简化的海洋平台分析模型合理,并且结构抗力参数服从正态分布;而极值冰力下,结构顶点最大位移服从对数正态分布。以上结论可为研究冰区海洋平台整体安全可靠性分析提供参考。 相似文献
4.
海上风电基础属于典型的柔性结构。由于冰与柔性抗冰结构相互作用的复杂性,长期以来尚未形成基于动冰力响应分析的结构设计。结构抗冰设计中大都是从极端荷载出发,只考虑最大静冰力或最大倾覆力矩。基于对渤海辽东湾柔性抗冰结构的多年监测,发现强烈的冰激振动引起柔性结构的风险性要远大于极端静冰荷载下结构的整体安全问题。为了明确冰区风电基础结构的抗冰性能及抗冰设计的合理性,文章结合基于多年现场冰与结构作用观测及冰荷载的研究成果,明确该类柔性结构与海冰作用形式及其动力特性;提出了柔性抗冰结构设计中应考虑的主要失效模式及评价方法。最后,以渤海某典型风电基础为例,对其抗冰性能进行评价。该文的研究可为寒区风电基础的抗冰设计及安全保障提供合理依据。 相似文献
5.
现行JTS 144-1—2010《港口工程荷载规范》提出了海冰和河冰的极限挤压冰力计算公式,但是规范中没有针对大面积淡水湖区的计算公式。基于实际工程,通过对比分析国内相关行业规范针对极限挤压冰力的计算公式,并结合数值模型实验得出,利用《港口工程荷载规范》的河冰公式计算得出的极限挤压冰力偏小,而海冰公式计算得出的极限挤压冰力偏大,根据现行JTG D60—2015《公路桥涵设计通用规范》得出的极限挤压冰力与数学模型模拟值基本一致。因此对于大面积淡水湖区极限挤压冰力的计算可以参考《公路桥涵设计通用规范》中的计算公式。该研究为计算大面积淡水湖区极限挤压冰力提供一定的依据,为修订规范时提供参考。 相似文献
6.
冰的温度膨胀力研究 总被引:1,自引:0,他引:1
在寒冷地区,各类水工建筑物均会受到冰荷载的作用,而冰的温度膨胀力是其中一种对结构产生重要影响的荷载.例如,坐落于寒冷地区的水库建筑、海中固定式结构、防波堤和护岸等.这些结构形成了冰的约束边界,当外界环境温度(主要是气温)发生变化时,冰的温度场也发生变化,从而引起冰的应变,产生温度应力,并对结构产生温度膨胀力.冰的温度膨胀力受多种因素的影响,包括约束边界的形状、约束体的刚度、冰层的相对厚度、升温速率、冰的应变率等.冰的温度膨胀力已引起较为广泛的关注,本文对目前国际上对冰的温度膨胀力具有代表性的几种估算方法进行了介绍和简单的评价,为实际工程的设计提供了一些参考依据. 相似文献
7.
在冰区油气开发中,锥体结构可以有效降低冰力,避免强烈的冰激振动,是目前渤海油气平台的主要结构形式。为研究海冰与锥体结构的相互作用过程,文章建立了适用于模拟海冰破碎特性的离散单元模型。该模型将海冰离散为若干个具有粘接-破碎功能的颗粒单元,并通过海冰弯曲试验确定了单元间的粘接强度;然后对海冰与锥体结构的作用过程进行了数值计算,获得了相应的动冰荷载及冰振响应;在此基础上讨论了不同锥角影响下冰荷载及结构振动响应的变化规律。结果表明,水平方向冰荷载及结构冰振响应随锥角的增加明显增加,而竖直方向冰荷载则显著降低。该离散单元模型还可进一步应用于不同类型抗冰结构的冰荷载分析,有助于解决冰区结构物的抗冰结构设计和冰致疲劳分析。 相似文献
8.
9.
10.
为解决冰区导管架节点存在的冰激与波浪荷载联合疲劳作用问题,采用美国石油学会的简化疲劳分析方法确定受波浪影响较大的节点及其所受荷载的方向,利用SACS软件对这些节点的波浪详细谱疲劳进行分析.针对冰激荷载,考虑到不同冰速下结构物的动力响应差异,分别利用ANSYS软件的瞬态分析和谱分析方法对节点的稳态冰振和随机冰振疲劳影响进... 相似文献
11.
12.
13.
14.
本文针对中国新型极地考察船所受冰载荷进行了研究,其中包含了平整冰阻力和浮冰碰撞力.对于船舶设计者和建造者来说,船舶冰载荷的预估非常重要.本文采用经验公式方法计算了该船在平整冰中航行的冰阻力,并且与模型试验结果进行了对比.结果显示,计算和试验结果中的冰阻力都随船舶航行速度的增大而增大,经验公式方法可以预测出合理的平整冰阻力.通过计算得到了该船的性能曲线,即该船在不同厚度平整冰中航行所能达到的速度.此外,本文还考虑了该船与圆形浮冰之间的三维斜向碰撞问题,采用解析方法评估了浮冰对船舶的撞击力,研究了撞击位置、法向框架角度以及浮冰尺寸对碰撞力的影响.基于计算结果,本文就冰载荷的预测进行了讨论并提出了一些建议. 相似文献
15.
16.
Ice loads are important environmental loads that can influence the structural safety of ships during navigation in ice-covered waters. The identification of ice loads on ship hulls is the core of ice load monitoring. In this study, a new ice load identification model based on Green kernel and regularization methods is established. First, the forward model for ice load identification is developed through the discretised convolution integral of ice loads. Next, three commonly used regularization methods, including Tikhonov, truncated singular value decomposition, and least square QR-factorization (LSQR) are adopted to reduce solution errors. The LSQR method is thereafter selected as the optimal regularization operator, and its regular property is proved by numerical cases with ice-induced strains that contain noise. Finally, two load identification cases are conducted on an experimental rig to evaluate the feasibility of the model in ice load identification. The identified loads can determine the signal features of applied loads in the time domain with good accuracy. This identification model provides new insights for full-scale ice load monitoring. 相似文献
17.
18.
In the structural design of the Polar Class ships, glancing impact with ice has been considered as the governing load scenario for dimensioning the bow structure. At present, non-linear transient dynamic analysis has been reckoned as a fundamental requirement in the assessment of the structural strength of ships with higher ice classes. Under such requirement, understanding of the dynamic characteristics of the ship-ice impact load appears significant importance. The present study aims to investigate the spatial and temporal variations of the impact loads by simulating the glancing impact events between a polar research vessel and giant ice floes in ice tank. The ship-ice impact loads were recorded by a grid-based tactile sensor attached on the bow area of the model ship. To achieve a reasonable simulation on the design scenario described by the IACS Unified Requirements for Polar Class Ships (UR I), a series of methodological calibration tests were preliminarily carried out to determine the key parameters that should be carefully monitored and controlled, accompanying with thorough discussions on the ship-ice impact process. This paper provides detailed information on the preliminary methodological calibrations and the tactile data processing techniques, including the identification of the ship-ice contact area, the depiction of the ice loading trail and the outline of the spatial distributions of local ice pressures. A companion paper provides detailed analyses and discussions regarding the spatial and temporal variation of the ice impact loads from the formal tests based on the proposed testing procedures obtained by the methodological calibrations. 相似文献