Optimal Linear Active Suspensions with Multivariable Integral Control

In this paper, an optimal suspension system is derived for a quarter-car model using multivariable integral control. The suspension system features two parts. The first part is an integral control acting on suspension deflection to ensure zero steady-sate offset due to body and maneuvering forces as well as road inputs. The second is a proportional control operating on the vehicle system states for vibration control and performance improvement. The optimal ride performance of the active suspensions based on linear full-state feedback control laws with and without integral control together with the performance of passive suspensions are compared.     

Performance of Low-bandwidth, Semi-active Damping Concepts for Suspension Control

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Performance of Low-bandwidth,Semi-active Damping Concepts for Suspension Control

Abstract

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

DISCUSSION NOTE on Karnopp's article “Active Damping in Road Vehicle Suspension Systems”

SUMMARY

In this paper, an optimal suspension system is derived for a quarter-car model using multivariable integral control. The suspension system features two parts. The first part is an integral control acting on suspension deflection to ensure zero steady-sate offset due to body and maneuvering forces as well as road inputs. The second is a proportional control operating on the vehicle system states for vibration control and performance improvement. The optimal ride performance of the active suspensions based on linear full-state feedback control laws with and without integral control together with the performance of passive suspensions are compared.     

Optimal Performance of Variable Component Suspensions

SUMMARY

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

A semi-active control suspension system for railway vehicles with magnetorheological fluid dampers

The high-speed train has achieved great progress in the last decades. It is one of the most important modes of transportation between cities. With the rapid development of the high-speed train, its safety issue is paid much more attention than ever before. To improve the stability of the vehicle with high speed, extra dampers (i.e. anti-hunting damper) are used in the traditional bogies with passive suspension system. However, the curving performance of the vehicle is undermined due to the extra lateral force generated by the dampers. The active suspension systems proposed in the last decades attempt to solve the vehicle steering issue. However, the active suspension systems need extra actuators driven by electrical power or hydraulic power. There are some implementation and even safety issues which are not easy to be overcome. In this paper, an innovative semi-active controlled lateral suspension system for railway vehicles is proposed. Four magnetorheological fluid dampers are fixed to the primary suspension system of each bogie. They are controlled by online controllers for enhancing the running stability on the straight track line on the one hand and further improving the curving performance by controlling the damper force on the other hand. Two control strategies are proposed in the light of the pure rolling concept. The effectiveness of the proposed strategies is demonstrated by SIMPACK and Matlab co-simulation for a full railway vehicle with two conventional bogies.     

四级阻尼可调式液压互联悬架系统性能研究

提出了一种新型四级阻尼可调式液压互联悬架 （FDAHIS） 系统。FDAHIS系统在被动液压互联悬架系统的阻尼阀上并联了两个常通孔面积不同的电磁开关阀,通过反馈控制策略控制电磁阀开闭状态,调节系统液压流量,从而实现阻尼四级可调。为了研究该系统性能,建立FDAHIS系统模型和七自由度整车模型。通过系统单元台架试验对该模型进行了验证。整车仿真结果表明,与被动的液压互联悬架 （HIS） 系统相比,FDAHIS系统在车辆行驶平顺性和抗俯仰性能方面表现更佳。     

Application of observer-based fault detection in vehicle roll control

This paper describes how observer-based techniques for intelligent fault detection were applied to monitoring an active suspension control system in an experimental articulated heavy vehicle. The aim was to define a practical method for detecting faults, taking into account the nonlinearities of the vehicle. The experimental vehicle was divided conceptually into subsystems, namely the passive dynamics of the trailer, the dynamics of the hydraulic actuators, and the expected response of the closed-loop system. A linear dynamic model was designed for each subsystem. A fault detection observer was then designed for each dynamic model. The observer feedback gains were chosen to optimise estimation by the observer residual of specified errors on the output measurements. The observer residuals were then normalised and combined logically to provide a fault diagnosis. The performance of the fault detection scheme is demonstrated in the case of sensor faults and changes in the operation of the active control system.     

Optimal Performance of Variable Component Suspensions

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

Stochastic Optimal Control of Highway Tractors with Active Suspensions

Stochastic optimal control and estimation theories are used to design an active suspension system for a cab ride in a tractor-semitrailer vehicle. A discrete-continuous vehicle model with eleven degrees of freedom is augmented by a stochastic road excitation model and a human perception of vibration shape filter. Both perfect measurement and estimated state cases are considered. The impact of the measurement noise on the design of the optimal controller is demonstrated. The performance of the optimally controlled system is compared with an optimal passive system. It is shown that significant improvements in ride comfort can be achieved through the use of actively controlled cab suspensions.     

Theoretical Limitations in Active Vehicle Suspensions

Vehicle suspensions in which forces are generated in response to feedback signals by active elements obviously offer increased design flexibility compared to conventional suspensions using passive elements such as springs and dampers. It is often assumed that if practical difficulties are neglected, active systems could in principle produce arbitrary ideal, behavior. It is shown, using a simple linear two degree-of-freedom suspension system, model that even using complete state feed back and in the case of in which the system is controllable in the control theory sense, there still are limitations to suspension performance in the fully active case. If the ideal suspension performance is defined based on low-pass filtering of roadway unevenness inputs, an active suspension may not offer much better performance than a partially active or adaptive passive suspension depending upon the values of certain vehicle parameters.     

Theoretical Limitations in Active Vehicle Suspensions

SUMMARY

Vehicle suspensions in which forces are generated in response to feedback signals by active elements obviously offer increased design flexibility compared to conventional suspensions using passive elements such as springs and dampers. It is often assumed that if practical difficulties are neglected, active systems could in principle produce arbitrary ideal, behavior. It is shown, using a simple linear two degree-of-freedom suspension system, model that even using complete state feed back and in the case of in which the system is controllable in the control theory sense, there still are limitations to suspension performance in the fully active case. If the ideal suspension performance is defined based on low-pass filtering of roadway unevenness inputs, an active suspension may not offer much better performance than a partially active or adaptive passive suspension depending upon the values of certain vehicle parameters.     

Structured H2 Optimization of Vehicle Suspensions Based on Multi-Wheel Models

Summary Various control techniques, especially LQG optimal control, have been applied to the design of active and semi-active vehicle suspensions over the past several decades. However passive suspensions remain dominant in the automotive marketplace because they are simple, reliable, and inexpensive. The force generated by a passive suspension at a given wheel can depend only on the relative displacement and velocity at that wheel, and the suspension parameters for the left and right wheels are usually required to be equal. Therefore, a passive vehicle suspension can be viewed as a decentralized feedback controller with constraints to guarantee suspension symmetry. In this paper, we cast the optimization of passive vehicle suspensions as structure-constrained LQG/H2 optimal control problems. Correlated road random excitations are taken as the disturbance inputs; ride comfort, road handling, suspension travel, and vehicle-body attitude are included in the cost outputs. We derive a set of necessary conditions for optimality and then develop a gradient-based method to efficiently solve the structure-constrained H2 optimization problem. An eight-DOF four-wheel-vehicle model is studied as an example to illustrate application of the procedure, which is useful for design of both passive suspensions and active suspensions with controller-structure constraints.     

基于微分几何理论的汽车半主动悬架非线性振动控制

针对汽车悬架系统的非线性特性,采用1／4汽车二自由度悬架模型分析半主动悬架控制。应用微分几何理论得到输出-干扰解耦方法,再经适当的坐标变换将该模型由非线性系统简化成一线性系统,并对此系统进行最优控制,然后通过非线性状态反馈实现对原系统的半主动控制。与被动悬架的仿真结果进行了比较,表明这种针对具有非线性特征的半主动悬架的非线性控制方法是可行的。通过功率谱分析,控制后系统的能量比被动悬架更趋于平均,悬架动态性能更稳定。     

Energy Requirements of a Passive and an Electromechanical Active Suspension System

Passive suspensions are designed to dissipate the energy otherwise transferred to a vehicle's body through interactions with a roadway or terrain. A bond graph representation of an independent suspension design was developed to study the energy flow through a vehicle. The bond graph model was tuned and validated through experimental tests and was found to produce suitable results. Examining the bond graph reveals that the dissipated energy associated with vertical and transverse coordinates generally originates from the longitudinal motion of the vehicle and is transferred through the tire-ground contact patch. Additionally, since the longitudinal energy originates from the vehicle's engine, the energy dissipated via the suspension shock absorber as well as other components (e.g., mechanical joints, etc.) essentially dissipate some engine energy. The plots presented in the paper support this theory by showing that upon traveling a rough terrain, the vehicle's longitudinal velocity drops more when vertical vibrations increase. Results show that a vehicle equipped with a passive suspension experiences a larger velocity drop compared to one with an active suspension traversing the same rough terrain. The paper compares the results of simulation of an analytical bond graph model of an active suspension system with experimental results and finds good agreement between the two. Other simulations show that relative to passive suspensions, not only do active suspensions yield substantial improvement in ride quality, they can also result in substantial energy savings. This paper concludes that if electromechanical actuators are supplemented by passive springs to support the vehicle static weight, the amount of energy required for operation of actuators is significantly less than the amount dissipated by conventional shock absorbers.     

Energy Requirements of a Passive and an Electromechanical Active Suspension System

Passive suspensions are designed to dissipate the energy otherwise transferred to a vehicle's body through interactions with a roadway or terrain. A bond graph representation of an independent suspension design was developed to study the energy flow through a vehicle. The bond graph model was tuned and validated through experimental tests and was found to produce suitable results. Examining the bond graph reveals that the dissipated energy associated with vertical and transverse coordinates generally originates from the longitudinal motion of the vehicle and is transferred through the tire-ground contact patch. Additionally, since the longitudinal energy originates from the vehicle's engine, the energy dissipated via the suspension shock absorber as well as other components (e.g., mechanical joints, etc.) essentially dissipate some engine energy. The plots presented in the paper support this theory by showing that upon traveling a rough terrain, the vehicle's longitudinal velocity drops more when vertical vibrations increase. Results show that a vehicle equipped with a passive suspension experiences a larger velocity drop compared to one with an active suspension traversing the same rough terrain. The paper compares the results of simulation of an analytical bond graph model of an active suspension system with experimental results and finds good agreement between the two. Other simulations show that relative to passive suspensions, not only do active suspensions yield substantial improvement in ride quality, they can also result in substantial energy savings. This paper concludes that if electromechanical actuators are supplemented by passive springs to support the vehicle static weight, the amount of energy required for operation of actuators is significantly less than the amount dissipated by conventional shock absorbers.     

Active Control of Non-stationary Response of Vehicles with Nonlinear Suspensions

Active control of non-stationary response of a single degree of freedom vehicle model with nonlinear passive suspension elements is considered in this paper. The method of equivalent linearization is used to derive the equivalent linear model and the optimal control laws are obtained by using stochastic optimal control theory based on full state information. Velocity squared quadratic damping and hysteresis type of stiffness nonlinearities are considered. The effect of the nonlinearities on the active system performance is studied. The performance of active suspensions with nonlinear passive elements is found to be superior to the corresponding passive suspension systems.     

基于SIMULINK的车辆主动悬架LQG控制仿真研究

通过建立1／4车辆模型,应用最优控制理论进行了车辆主动悬架的LQG(Linear Quadratic Gaussian)控制器的设计,并在Matlab／Simulink环境中建立系统模型并进行仿真,将仿真结果与被动悬架仿真结果进行对比分析。仿真结果表明,具有LQG控制器的主动悬架对车辆行驶平顺性和乘坐舒适性的改善有良好的效果。     

基于统一模型的转向-悬架系统最优综合控制方法

通过对车辆底盘系统中的转向和悬架系统建立统一的数学模型,利用M atlab/S imu link仿真,结合最优控制理论,分别对被动悬架兼前轮转向系统与主动悬架兼四轮转向综合控制系统进行了对比研究。理论分析与仿真试验表明,综合控制系统下车辆的操纵稳定性和平顺性都得到了很大的提高。     

Suboptimal Control Design of Active and Passive Suspensions Based on a Full Car Model

An optimal control design method is introduced and then applied to the optimum design of active and passive suspension systems. A basic three-dimensional 7-DOF car riding model subjected to four correlated random road inputs is considered. The design method is basically developed to allow arbitrary choice of sensors for various car state variables to be used for feedback control of each suspension unit. Previous studies show that full-state control laws and even some limited-state control laws often include feedback gains which are almost zero. Some other gains, although not zero, don't play an important role in improving the system performance measures. With the method proposed in this work, every suspension unit can have its own feedback measurements and the criterion function can be related to all state and control variables. Thus a large number of active and semi-active suspension systems with full- or limited-state control laws based on different measurement combination can be suggested, studied, and compared with each other. Instead of comparing these optimized active and semi-active suspension systems with a basic, passive suspension, the passive system itself is optimized with the same criterion. Simulations in the time domain and frequency analyses are performed, and comparisons are made among the systems in terms of r.m.s. car response measures and ISO riding comfort criterion.