极端复杂地质条件下TBM隧道施工关键技术研究及应用北大核心CSCD

大瑞铁路高黎贡山隧道、引汉济渭秦岭隧洞、滇中引水香炉山隧洞等工程的相继开工建设,使富水破碎极软地层带来的TBM卡机、高地应力极硬岩地层带来的岩爆等TBM施工问题日益凸显。文章首先对比阐述了国内TBM隧道工程建设过程中常遇到的软弱破碎、极硬花岗岩等典型不良地质及其对TBM掘进所带来的影响,在总结分析辽西北供水、引松供水、引洮供水等工程建设过程中出现的隧道局部塌方、TBM卡机等案例及其影响因素的基础上,以极端复杂地质条件TBM掘进关键技术为对象进行了系统研究论述,结果表明:(1)超前地质预报技术是TBM施工应对极端复杂地质的重要手段,但目前尚无法对前方中远距离地质状况进行准确量化预测;基于微震监测分析结果,根据可能发生的轻微、中等、强烈等不同等级的岩爆,制定对应处置措施;节理发育、炭质板岩、断层破碎带等不同软弱破碎地层,应采取针对性的防卡机措施,同时可根据不良地质段的长度来选择合适的脱困方案;(2)TBM推力、推进速度、刀盘转速及扭矩等掘进参数的异常波动,是表征掌子面前方地质条件状态的重要指标,TBM掘进前,根据前期预判的全断面硬岩、软弱破碎等围岩条件,分别选择合适的掘进参数;TBM掘进过程中,应基于掘进参数异常变化,纠正地质条件预判并采取对应的调控措施,进而确保TBM处于最佳掘进状态;(3)针对既有TBM难以适应现有地质条件的情况,以引洮供水隧洞、引红济石隧洞、引汉济渭隧洞等工程为例,对TBM改造技术进行了分析论述。最后,针对极端复杂地质条件下的TBM隧道工程建设新问题及其应对措施进行了展望与探讨。     

铁路隧道凸壳型防排水板通水能力研究

文章基于我国铁路隧道防排水体系的技术现状及铁路隧道防排水领域存在的主要问题,介绍了凸壳型防排水板的基本特征,并对凸壳型防排水板的等效管径、通水量等进行了理论计算和研究。结果表明:单位幅宽(隧道纵向延长米)凸壳型防排水板的最小等效管径为0.0626 m,不同工况下其通水量为376~2138 m^3/d;凸壳型防排水板的通水能力是环向盲管的18~38倍;提高凸壳型防排水板凸壳体的抗压强度是确保其通水能力的有效措施;凸壳型防排水板可全面替代传统的防水板与环向排水盲管设置。     

西津水利枢纽二线船闸工程总平面布置方案研究

西津水利枢纽二线船闸工程是西江黄金水道首批建设项目之一,其船闸轴线位置选择及总平面布置是总体设计和控制工程投资的关键。文章结合西津水利枢纽二线船闸工程建设规模和项目特点,提出了不同的船闸轴线与总平面布置方案,并通过分析比选得出推荐方案,为类似船闸工程设计提供参考及借鉴。     

有别于交通隧道的输水隧道设计

本文主要针对上海青草沙水源地长江过江管隧道工程,分析了输水隧道的特点和难点,通过对单层衬砌和双层衬砌结构方案的比选,着重对单层衬砌结构进行了施工、正常运营、检修等各工况的综合分析和计算,提出采用单排环向螺栓、铸铁手孔、双道弹性密封垫等设计,满足输水隧道的功能要求。     

上海青草沙原水工程五号沟泵站深基坑施工风险及其对策

针对上海青草沙原水工程五号沟泵站的工程特点及施工风险,从基坑开挖、降承压水等方面详细分析了该大型地下水工结构的施工技术特点和风险控制对策,可为类似工程提供参考。     

埋地输水管线牺牲阳极的阴极保护

通过对大连市引英入连输水应急工程土壤腐蚀性的现场勘察,为该工程钢质输水管网设计了牺牲阳极的阴极保护方法。30个月的实践证明,钢质输水管线经牺牲阳极的阴极保护后,整个阴极保护系统稳定,电位分布均匀,阳极保持较负的工作电位,提供较高的驱动电压,使管网处于良好的保护状态,防止了土壤的电化学腐蚀,达到了设计标准。     

利用涌水的公路隧道消防供水系统

隧道涌水是施工、运营中引人关注的问题,文章以福建漳诏高速公路鼓志山隧道为例,介绍了利用隧道涌水取代深井系统取水、以高位水池重力流取代全自动加压供水的消防供水系统。     

Evaluating the social cost of cruise ships air emissions in major ports of Greece

Detailed NO_x, SO₂ and PM_2.5 emissions have been estimated for cruise ships in the five busiest Greek ports (i.e. Piraeus, Santorini, Mykonos, Corfu and Katakolo) for year 2013. The emissions were analyzed in terms of gas species, seasonality and activity. The total in-port inventory of cruise shipping accounted to 2742.7 tons: with NO_x being dominant (1887.5 tons), followed by SO₂ and PM_2.5 (760.9 and 94.3 tons respectively). Emissions during hotelling corresponded to 88.5% of total and have significantly outweighed those produced during ships’ maneuvering activities (11.5% of total). Seasonality was found to play a major role, as summer emissions and associated impacts were significantly augmented. The anticipated health impacts of ship emissions can reach to €24.3 million or to €5.3 per passenger proving the necessity of control of the emissions produced by cruise ships in port cities or policy and measures towards a more efficient cruise industry.     

The impact of Low Emission Zones on particulate matter concentration and public health

A common policy for reducing particulate matter concentrations in the European Union is the introduction of Low Emission Zones (LEZs), which may only be entered by vehicles meeting predefined emission standards. This paper examines the effectiveness of LEZs for reducing PM₁₀ levels in urban areas in Germany and quantifies the associated health impacts from reduced air pollution within the zones. We employ a fixed effects panel data model for daily observations of PM₁₀ concentrations from 2000 to 2009 and control, inter alia, for local meteorological conditions and traffic volume. We apply the regression outputs to a concentration response function derived from the epidemiological literature to calculate associated health impacts of the introduction of LEZs in 25 German cities with 3.96 million inhabitants. Associated uncertainties are accounted for in Monte-Carlo simulations. It is found that the introduction of LEZs has significantly reduced inner city PM₁₀ levels. We estimate the total mean health impact from reduced air pollution in 2010 due to the introduction of stage 1 zones to be ∼760 million EUR in the 25 LEZ cities in the sample, whereas total mean health benefits are ∼2.4 billion EUR for the more stringent stage 2 zones when applied in the same cities.     

Hybrid- and battery-electric vehicles offer low-cost climate benefits in China

Car ownership in China is expected to grow dramatically in the coming decades. If growing personal vehicle demand is met with conventional cars, the increase in greenhouse gas emissions will be substantial. One way to mitigate carbon dioxide (CO₂) emissions from passenger travel is to meet growing demand for cars with alternative vehicles such as hybrid- and battery-electric vehicles (HEVs and BEVs). Our study examines the cost-effectiveness of transitioning from conventional cars to HEVs and BEVs, by calculating their marginal abatement cost (MAC) of carbon in the long-run. We find that transitioning from conventional to hybrid and battery electric light-duty, four-wheel vehicles can achieve carbon emissions reductions at a negative cost (i.e. at a net benefit) in China. In 2030, the average MAC is estimated to be about −$140/ton CO₂ for HEVs and −$515/ton CO₂-saved for BEVs, varying by key parameters. The total mitigation potential of each vehicle technology is estimated to be 1.38 million tons for HEVs and 0.75 million tons for BEVs.     

Biases in response over time in a seven-day travel diary

Data from multi-day travel or activity diaries might be biased if recording inaccuracies and tendencies for respondents to skip certain types of trips or activities increases (or decreases) from day-to-day over the diary period. One objective of the research reported here is to test for such temporal biases in a seven-day travel diary. A second objective is to calculate correction factors which can be applied to the data in the case that biases are found. The analyses were conducted using regression and analysis-of-variance techniques. The variables investigated included total trips per day, total travel time per day, and trips per day by various modes (such as walking, car driver and car passenger). Results showed that most biases per capita statistics are due to increases over time in the percentage of respondents reporting no travel at all for an entire day. However, even after accounting for this bias by measuring statistics in terms of per mobile person, there remains a decrease over time of about 3.5 percent per day in the reporting of walking trips. This appears to be the main factor in the overall bias of about one percent per day in total trips per mobile person per day. No significant differences were found among population segments in terms of the levels of their biases.     

Urban transportation in Chinese cities: An efficiency assessment

We use 2008 data for 34 Chinese cities to compare urban transportation systems. The results show stronger eastern and central cities focusing more on high capacity and less on sustainable modes of transportation, while western cities do the opposite. Chinese cities with more sustainable transportation are also more likely to have lower gross domestic product per capita, be smaller, are less urbanized and have higher bus usage. This model needs to change to align with China’s new policy priorities.     

Rail freight efficiency and competitiveness in Australia

In 1994/95, the Australian rail freight task was approximately 100 billion tonne kilometres (btkm). This freight task included some 37 btkm for the haulage of iron ore in Western Australia, 28 btkm for coal haulage in Queensland and New South Wales and about 16 btkm for interstate rail freight. This paper mainly concerns how improvements can be made to the efficiency and competitiveness of interstate rail freight services through the upgrading of sections of mainline track that currently have severe speed‐weight restrictions. Recent improvements in rail freight efficiency are discussed, with emphasis on two indicators: average unit revenues (cents per net tonne km), and average energy efficiency (net tonne km per MJ). Rail freight efficiency is high for the Western Australia iron‐ore operations, Queensland coal operations and Adelaide‐Perth general freight operations. However, between Australia's three largest cities of Melbourne, Sydney and Brisbane, some 36% of the mainline track fails to meet basic fast freight train standards with a ruling grade of 1 in 66 and no curve radius less than 800 m. The contraints on efficient rail freight operations imposed by severe terrain, and how the effects of terrain may be reduced by improved track alignment, are discussed. Some economically warranted rail track investment measures are outlined, including those identified for a National Transport Planning Taskforce. These measures have the potential to reduce liquid fuel use by over 250 million litres a year. Factors affecting competitive neutrality between road and rail freight that are outside of the present scope of Australia's National Competition Policy are broadly considered. These factors include the extensive upgrading of the National Highway System with full Federal funding, and low levels of road cost recovery from heavy trucks operating over long distances.     

特长隧洞TBM施工通风系统设计

以辽宁大伙房水库输水隧洞工程为背景,详细设计了TBM2标段独头掘进9 km的施工通风系统,选取了漏风系数、摩阻系数等特征参数,计算了风量、风压和通风功率,并对通风设备及其布置进行了优化匹配。在世界上首次采用了每段长度为300 m的2.2 m通风软管,取得了很好的通风效果。     

广西梧州港赤水圩作业区码头工程给排水设计

文章以广西梧州港赤水圩作业区码头工程为例,系统介绍了该码头给排水工程的设计要点,为类似工程项目的给排水设计提供借鉴。     

Joint development at transit stations in the United States

Joint development, as the term is generally used in connection with transit systems in the United States, is real estate development that is closely linked to public transportation services and station facilities, and takes advantage of the market and locational advantages provided by them. Research conducted by LEK Associates for the Urban Mass Transportation Administration (UMTA) suggests that, in addition to helping shape urban growth and land development, joint development is also a surprisingly effective means of increasing transit system ridership and farebox revenues, as well as a source of increasingly significant revenues from the sale or lease of air rights.The completion of nine joint development projects in as many different cities, started under the former Urban Initiatives Program, for example, net additional annual ridership might reach 12000000 one-way trips. Net additional annual farebox revenues might reach over $9000000. This added revenue would be sufficient to repay the $62 million combined UMTA/transit operator investment in the nine projects, exclusive of the costs of the basic transit system improvements around which the projects are planned, in less than six years.Among transit authority-administered joint development programs examined in a separate study, the Washington Metropolitan Area Transit Authority (WMATA) has had the most success in generating significant value capture income. For example, the cumulative revenue realized by WMATA from just six joint development projects in the Washington, DC region, through September 1983 exceeded $ 6.9 million. Projections through fiscal year 1986 indicate cumulative revenues approximating $ 28 million will be received from developer leases.     

Some lessons from the LRT in Tunis and the transferability of experience

Considering the debate about the technological options to get a modern mass transport supply in developing cities the experience of Tunis is very interesting to analyse and to appraise as this city is operating a LRT network since 1985. This paper presents the elements of success of this experience (satisfying level of ridership, moderate cost of investment, coverage of operating cost by receipts, accessibility of the central area, etc.) but also its limits coming from the limited capacity at the city scale and the inability to stop the extension of the car use in the city. That means this project has to be completed by another one, more complex and costly which would consist of a railway regional network, which is now studied in detail.A short comparison is made with other cities in Maghreb (Algiers, Casablanca) experimenting also the design of metro projects which were more ambitious but with less success as they could not yet be implemented. Among the lessons thrown from this experience one insists on the importance of studies which have accompanied the design and the implementation of the project.     

基于水锤模拟的长输管道运行薄弱段分析

结合国内某长距离输水管道工程实例,通过水锤模拟对输水管道进行典型工况分析,确定输水管道易发生爆管的薄弱地段,并判断其危险等级。结果表明：对长距离输水系统进行典型工况水锤模拟可有效判断管道薄弱位置,通过对爆管事故内因、外因分析可预测管道薄弱段发生事故时危害程度。针对不同工程特点进行长输管道运行薄弱段分析,可提高供水可靠性,为管道安全运行管理提供依据。     

排水泵站计算机优化控制策略的应用

国内许多城市的合流制排水泵站存在着由于季节和气候变化所引起的污水量及变化速率的不同,采用手动控制和一般的自动控制常常造成水泵机组的频繁启动与停止.采用水泵机组微机控制优化方案可以解决合流制排水泵站频繁启停泵的问题.文中给出了系统的硬件结构及程序框图.     

Impacts of motor vehicle operation on water quality in the US – Cleanup costs and policies

This paper investigates the costs of controlling some of the environmental impacts of motor vehicle transportation on groundwater and on surface waters. We estimate that annualized costs of cleaning-up leaking underground storage tanks range from $0.8 billion to $2.1 billion per year over 10 years. Annualized costs of controlling highway runoff from principal arterials in the US are much larger: they range from $2.9 billion to $15.6 billion per year over 20 years (1.6–8.3% of annualized highway transportation expenditures). Some causes of non-point source pollution were unintentionally created by regulations or could be addressed by simple design changes of motor vehicles. A review of applicable measures suggests that effective policies should combine economic incentives, information campaigns, and enforcement, coupled with preventive environmental measures. In general, preventing water pollution from motor vehicles would be much cheaper than cleaning it up.