Development of control logic for hydraulic active roll control system

Developed in this research is a control logic for the ARC (Active Roll Control) system that uses rotary-type hydraulic stabilizer actuators at the front and rear axles. The hydraulic components of the system were modeled in detail using AMESim, and a driving logic for the hydraulic circuit was constructed based upon the model. The performance of the driving logic was evaluated on a test bench, and it demonstrated good pressure tracking capability. The control logic was then designed with the target of reducing the roll motion of the vehicle during cornering. The control logic consists of two parts: a feedforward controller that generates anti-roll moments in response to the centrifugal force, and a feedback controller that generates anti-roll moments in order to make the roll angle to follow its target value. The developed ARC logic was evaluated on a test vehicle under various driving conditions including a slowly accelerated circular motion and a sinusoidal steering. Through the test, the ARC system demonstrated successful reduction of the roll motion under all conditions, and any discomfort due to the control delay was not observed even at a fast steering maneuver.     

车辆系统垂向与横向耦合的侧倾状态估计

为有效解决复杂行驶工况下车辆耦合侧倾运动状态无法精确获取,进而对车辆系统操纵稳定性与乘坐舒适性兼顾优化无法提供准确输入的难题,本文中设计了基于车辆垂向与横向耦合动力学的双非线性状态观测器算法,以实现复杂行驶工况下车辆耦合侧倾运动状态的实时准确估计。首先,建立了路面激励模型与整车系统垂向与横向耦合动力学模型;接着,利用无迹卡尔曼滤波方法(UKF)与非线性模糊观测(T-S)理论,设计了非线性状态观测算法,以在不同路面激励工况下对车辆系统簧载质量与侧倾状态进行联合估计;最后,运用CarSim■动力学软件,对比分析了在标准A级与C级路面上进行J-turn试验工况下,采用联合状态观测器(UKF&T-S)实时估计车辆侧倾角与侧倾率的观测精度。结果表明,本文所设计的UKF&T-S观测器可有效估计车辆侧倾状态,且与CarSim■仿真数据相比识别状态标准偏差不超过10%。     

Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Optimal preview game theory approach to vehicle stability controller design

Dynamic game theory brings together different features that are keys to many situations in control design: optimisation behaviour, the presence of multiple agents/players, enduring consequences of decisions and robustness with respect to variability in the environment, etc. In the presented methodology, vehicle stability is represented by a cooperative dynamic/difference game such that its two agents (players), namely the driver and the direct yaw controller (DYC), are working together to provide more stability to the vehicle system. While the driver provides the steering wheel control, the DYC control algorithm is obtained by the Nash game theory to ensure optimal performance as well as robustness to disturbances. The common two-degrees-of-freedom vehicle-handling performance model is put into discrete form to develop the game equations of motion. To evaluate the developed control algorithm, CarSim with its built-in nonlinear vehicle model along with the Pacejka tire model is used. The control algorithm is evaluated for a lane change manoeuvre, and the optimal set of steering angle and corrective yaw moment is calculated and fed to the test vehicle. Simulation results show that the optimal preview control algorithm can significantly reduce lateral velocity, yaw rate, and roll angle, which all contribute to enhancing vehicle stability.     

Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Active Roll Control of Articulated Vehicles

This paper describes an investigation into active roll control of articulated vehicles. The objective is to minimise lateral load transfer using anti-roll bars incorporating low bandwidth hydraulic actuators. Results from handling tests performed on an articulated vehicle are used to validate a nonlinear yaw/roll model of the vehicle. The methodology used to design lateral acceleration controllers for vehicles equipped with active anti-roll bars is developed using a simplified linear articulated vehicle model. The hardware limitations and power consumption requirements of the active elements are studied. The controller is then implemented in the validated articulated vehicle model to evaluate the performance of an articulated lorry with active anti-roll bars. The simulation results demonstrate the possibility of a significant improvement in transient roll performance of the vehicle, using a relatively low power system (10 kW), with low bandwidth actuators (5 Hz).     

Vehicle stability control system for enhancing steerabilty,lateral stability,and roll stability

The Vehicle stability control system is an active safety system designed to prevent accidents from occurring and to stabilize dynamic maneuvers of a vehicle by generating an artificial yaw moment using differential brakes. In this paper, in order to enhance vehicle steerability, lateral stability, and roll stability, each reference yaw rate is designed and combined into a target yaw rate depending on the driving situation. A yaw rate controller is designed to track the target yaw rate based on sliding mode control theory. To generate the total yaw moment required from the proposed yaw rate controller, each brake pressure is properly distributed with effective control wheel decision. Estimators are developed to identify the roll angle and body sideslip angle of a vehicle based on the simplified roll dynamics model and parameter adaptation approach. The performance of the proposed vehicle stability control system and estimation algorithms is verified with simulation results and experimental results.     

Rollover mitigation for a heavy commercial vehicle

A heavy commercial vehicle has a high probability of rollover because it is usually loaded heavily and thus has a high center of gravity. An anti-roll bar is efficient for rollover mitigation, but it can cause poor ride comfort when the roll stiffness is excessively high. Therefore, active roll control (ARC) systems have been developed to optimally control the roll state of a vehicle while maintaining ride comfort. Previously developed ARC systems have some disadvantages, such as cost, complexity, power consumption, and weight. In this study, an ARC-based rear air suspension for a heavy commercial vehicle, which does not require additional power for control, was designed and manufactured. The rollover index-based vehicle rollover mitigation control scheme was used for the ARC system. Multi-body dynamic models of the suspension subsystem and the full vehicle were used to design the rear air suspension and the ARC system. The reference rollover index was tuned through lab tests. Field tests, such as steady state cornering tests and step steer tests, demonstrated that the roll response characteristics in the steady state and transient state were improved.     

液压互联悬架抗侧倾控制研究（双语出版）

针对车辆减少能量消耗与提高抗侧倾能力需求,提出了一种主/被动可切换的液压互联悬架抗侧倾控制方法。基于9自由度车辆动力学模型,考虑蓄能器、液压缸、液压泵三者之间耦合的体积-流量-压力特性,建立液压互联悬架主动控制时域模型;结合"车身侧倾角-车身侧倾角速度"相平面法及车辆侧向加速度,得到车辆侧倾稳定域,并提出液压互联悬架系统侧倾稳定性控制介入与退出判据;在此基础上,采用Backstepping非线性控制算法设计主动液压互联抗侧倾控制器。最后,分析并改进侧倾稳定性评价指标,通过在MATLAB/Simulink环境下进行高速双移线、鱼钩试验等极端工况数值仿真,验证所提出的液压互联悬架主/被动切换控制系统能在减少能量消耗的情况下能否提高车辆抗侧翻的能力。研究结果表明：所提出的控制系统能有效提高车辆抗侧翻能力;当车辆侧倾状态超出设定的侧倾稳定区域介入线时,液压互联悬架系统由被动模式切换为主动抗侧倾模式,控制车辆侧倾状态回到稳定区域,以提高车辆侧倾稳定性;当判定车辆侧倾状态满足主动控制退出条件时,液压互联悬架系统回到被动模式,以减小能量消耗。     

Investigation of active torsion bar actuator configurations to reduce vehicle body roll

The increasing popularity of sport utility/light-duty vehicles has prompted the investigation of active roll management systems to reduce vehicle body roll. To minimize vehicle body roll and improve passenger comfort, one emerging solution is an active torsion bar control system. The validation of automotive safety systems requires analytical evaluation and laboratory testing prior to implementation on an actual vehicle. In this article, a computer simulation tool and accompanying hardware-in-the-loop test environment are presented for active torsion bar systems to study component configurations and performance limits. The numerical simulation illustrates that the hydraulic cylinder extension limits the active torsion system's ability to provide body roll angle reduction under various driving conditions. To compare the control system's time constant and body roll minimization capabilities for different hydraulic valve assemblies and equivalent hose lengths, an experimental test stand was created. For a typical hydraulic pressure and hose diameter, the equivalent hose length was not a key design variable that impacted the system response time. However, the servo-valve offered a quicker transient response and smoother steady-state behavior than the solenoid poppet actuators that may increase occupant safety and comfort.     

Investigation of active torsion bar actuator configurations to reduce vehicle body roll

The increasing popularity of sport utility/light-duty vehicles has prompted the investigation of active roll management systems to reduce vehicle body roll. To minimize vehicle body roll and improve passenger comfort, one emerging solution is an active torsion bar control system. The validation of automotive safety systems requires analytical evaluation and laboratory testing prior to implementation on an actual vehicle. In this article, a computer simulation tool and accompanying hardware-in-the-loop test environment are presented for active torsion bar systems to study component configurations and performance limits. The numerical simulation illustrates that the hydraulic cylinder extension limits the active torsion system’s ability to provide body roll angle reduction under various driving conditions. To compare the control system’s time constant and body roll minimization capabilities for different hydraulic valve assemblies and equivalent hose lengths, an experimental test stand was created. For a typical hydraulic pressure and hose diameter, the equivalent hose length was not a key design variable that impacted the system response time. However, the servo-valve offered a quicker transient response and smoother steady-state behavior than the solenoid poppet actuators that may increase occupant safety and comfort.     

Effective assessment of tyre–road friction coefficient using a hybrid estimator

Vehicle stability and active safety control depend heavily on tyre forces available on each wheel of a vehicle. Since tyre forces are strongly affected by the tyre–road friction coefficient, it is crucial to optimise the use of the adhesion limits of the tyres. This study presents a hybrid method to identify the road friction limitation; it contributes significantly to active vehicle safety. A hybrid estimator is developed based on the three degrees-of-freedom vehicle model, which considers longitudinal, lateral and yaw motions. The proposed hybrid estimator includes two sub-estimators: one is the vehicle state information estimator using the unscented Kalman filter and another is the integrated road friction estimator. By connecting two sub-estimators simultaneously, the proposed algorithm can effectively estimate the road friction coefficient. The performance of the proposed estimation algorithm is validated in CarSim/Matlab co-simulation environment under three different road conditions (high-μ, low-μ and mixed-μ). Simulation results show that the proposed estimator can assess vehicle states and road friction coefficient with good accuracy.     

基于蚁狮算法的UKF车辆状态参数估计器

为了准确获取分布式驱动电动汽车状态参数信息,满足车辆稳定性控制系统的需求,提出一种基于蚁狮算法的无迹卡尔曼滤波状态参数估计器。针对无迹卡尔曼滤波（UKF）过程中噪声协方差矩阵的不确定性,采用蚁狮优化算法（ALO）对其进行寻优,并引入奇异值分解（SVD）的方法来维持噪声协方差矩阵的正定性,此外,基于指数加权最小二乘法对车辆侧偏刚度进行辨识并将其作为状态参数估计器输入。基于MATLAB/Simulink和CarSim联合仿真平台,建立分布式驱动电动汽车参数估计模型,分别进行双移线工况和正弦迟滞工况仿真,并基于A&D5435快速原型开发平台进行双移线工况实车试验。仿真与试验结果表明：相比于SVDUKF算法估计结果,双移线仿真工况下,基于ALO-SVDUKF算法估计得到的质心侧偏角和横摆角速度的均方根误差分别降低了55.7%、30.7%,正弦迟滞仿真工况下,均方根误差分别降低了58.1%、85.1%,且在车辆处于极限失稳状态时仍能维持较好的估计效果;双移线试验工况下,横摆角速度的估计值与实际测量值之间的均方根误差仅为0.938 4（°）·s^-1;提出的基于ALO-SVDUKF算法的分布式驱动电动汽车状态参数估计器能够有效提高质心侧偏角和横摆角速度的估计精度,可为车辆稳定性控制提供精确的状态信息。     

Validation of the Harshness Problem of Automotive Active Suspensions

The advantages of an automotive fully active suspension system have been promised for many years. Among them, simultaneously achieving good body and wheel mode damping is of the most fundamental. However, implementations of such concepts with hydraulic actuators have generally exhibit worse-than-passive harshness performance when such vehicles are driven through small irregularities on the road. Additional forces are transmitted through the hydraulic active suspension to the vehicle body at high frequencies. Conventional wisdom blames the non-ideal actuator in practice for the problem since most analytical papers assume it an ideal force-producing element. However, the mechanism of generating such excessive force as well as the methodology of solving it has not been systematically demonstrated in the literature. In this paper, a high fidelity mathematical quarter vehicle model is first developed and identified with vehicle test data. This model captures realistic dynamic behaviors of the hydraulic active suspension. The mechanism of creating such harshness problem is then explained with this model. To validate such mechanism, a frequency domain methodology that yields an equal-to-passive high frequency performance while maintaining a good active body behavior was developed based on this model and demonstrated with a test vehicle. The model predicts the test results almost exactly.     

Allocation control algorithms design and comparison based on distributed drive electric vehicles

For a distributed drive electric vehicle (DDEV) which is equipped with redundant actuators, allocation control is a key technique. Three different allocation control algorithms are designated with fixed efficiency matrix, dynamic efficiency matrix, and direct yaw moment distribution, respectively. All these algorithms are applied in a vehicle stability control system with hierarchical control structure and evaluated from three aspects, namely, control precision, real-time characteristics, and control energy. Comparison results demonstrate that the algorithm with dynamic efficiency matrix has the best comprehensive performance, which is also validated in field tests based on a DDEV equipped with four motors.     

Vehicle Dynamic Control for In-Wheel Electric Vehicles Via Temperature Consideration of Braking Systems

?Vehicle dynamic control (VDC) systems play an important role with regard to vehicle stability and safety when turning. VDC systems prevent vehicles from spinning or slipping when cornering sharply by controlling vehicle yaw moment, which is generated by braking forces. Thus, it is important to control braking forces depending on the driving conditions of the vehicle. The required yaw moment to stabilize a vehicle is calculated through optimal control and a combination of braking forces used to generate the calculated yaw moment. However, braking forces can change due to frictional coefficients being affected by variations in temperature. This can cause vehicles to experience stability problems due an improper yaw moment being applied to the vehicle. In this paper, a brake temperature estimator based on the finite different method (FDM) was proposed with a friction coefficient estimator in order to solve this problem. The developed braking characteristic estimation model was used to develop a VDC cooperative control algorithm using hydraulic braking and the regenerative braking of an in-wheel motor. Performance simulations of the developed cooperative control algorithm were performed through cosimulation with MATLAB/Simulink and CarSim. From the simulation results, it was verified that vehicle stability was ensured despite any changes in the braking characteristics due to brake temperatures.     

Development of a fail-safe control strategy based on evaluation scenarios for an FCEV electronic brake system

This study presents a few fail-safe control strategies based on reliability evaluation scenarios for the electronic brake systems of green cars in several critical cases. CarSim and MATLAB Simulink were used to develop the FCEV model with regenerative braking involving EWBs and EMBs. The proposed reliability evaluation scenarios were simulated, and a few fail-safe control algorithms were verified using the proposed reliability evaluation scenarios with the developed FCEV simulation model. The reliability evaluation scenarios were developed using a combination of driving modes and FMEA results for these electronic brake systems.     

主动横向稳定器降低商用车侧倾的研究

将新式主动横向稳定器安装在中型货画的前轴和后轴，通过液压缸与车架连接。本文研究了该稳定器对降低车身侧倾和提高舒适性的效果。仿真分析和实车试验表明，采用前轮转角前馈控制方法，汽车转向时，稳定器产生反侧倾力矩，大幅度地降低车身侧倾。     

爆胎汽车整车运动分析及控制

通过轮胎试验得到GT175/60 R14轮胎在正常胎压及零胎压下的力学特性参数,以此为依据,运用CarS im软件对爆胎汽车进行整车动力学仿真,找出汽车偏航原因,分析驾驶员不同操作所引起的整车运动性能变化以及汽车稳定性控制系统对爆胎汽车的影响。仿真结果表明,稳定性控制系统对于减轻爆胎带来的后果具有积极的作用。     

基于改进粒子群优化算法的多目标自适应巡航控制

跟驰过程中,在保证安全性的前提下为了提升自适应巡航控制(ACC)系统的舒适性和燃油经济性,研究了多目标自适应巡航控制算法.在建立车间纵向运动学模型的基础上,根据模型预测控制理论,设计综合考虑安全性、舒适性、燃油经济性以及车辆自身限制等因素的目标函数和约束条件,并引入松弛因子向量软化硬约束边界解决无可行解问题.进一步在滚...