Nonlinear Dynamics of Vehicle Traction

Summary The purpose of this study is to understand the nonlinear dynamics of longitudinal ground vehicle traction. Specifically, single-wheel models of rubber-tired automobiles under straight-ahead braking and acceleration conditions are investigated in detail. Customarily, the forward vehicle speed and the rotational rate of the tire/wheel are taken as dynamic states. This paper motivates an alternative formulation in which wheel slip, a dimensionless measure of the difference between the vehicle speed and the circumferential speed of the tire relative to the wheel center, replaces the angular velocity of the tire/wheel as a dynamic state. This formulation offers new insight into the dynamic behavior of vehicle traction. The unique features of the modeling approach allow one to capture the full range of dynamic responses of the single-wheel traction models in a relatively simple geometric manner. The models developed here may also be useful for developing and implementing anti-lock brake and traction control control schemes.     

Nonlinear Dynamics of Vehicle Traction

Summary The purpose of this study is to understand the nonlinear dynamics of longitudinal ground vehicle traction. Specifically, single-wheel models of rubber-tired automobiles under straight-ahead braking and acceleration conditions are investigated in detail. Customarily, the forward vehicle speed and the rotational rate of the tire/wheel are taken as dynamic states. This paper motivates an alternative formulation in which wheel slip, a dimensionless measure of the difference between the vehicle speed and the circumferential speed of the tire relative to the wheel center, replaces the angular velocity of the tire/wheel as a dynamic state. This formulation offers new insight into the dynamic behavior of vehicle traction. The unique features of the modeling approach allow one to capture the full range of dynamic responses of the single-wheel traction models in a relatively simple geometric manner. The models developed here may also be useful for developing and implementing anti-lock brake and traction control control schemes.     

Lateral handling improvement with dynamic curvature control for an independent rear wheel drive EV

The integrated longitudinal and lateral dynamic motion control is important for four wheel independent drive (4WID) electric vehicles. Under critical driving conditions, direct yaw moment control (DYC) has been proved as effective for vehicle handling stability and maneuverability by implementing optimized torque distribution of each wheel, especially with independent wheel drive electric vehicles. The intended vehicle path upon driver steering input is heavily depending on the instantaneous vehicle speed, body side slip and yaw rate of a vehicle, which can directly affect the steering effort of driver. In this paper, we propose a dynamic curvature controller (DCC) by applying a the dynamic curvature of the path, derived from vehicle dynamic state variables; yaw rate, side slip angle, and speed of a vehicle. The proposed controller, combined with DYC and wheel longitudinal slip control, is to utilize the dynamic curvature as a target control parameter for a feedback, avoiding estimating the vehicle side-slip angle. The effectiveness of the proposed controller, in view of stability and improved handling, has been validated with numerical simulations and a series of experiments during cornering engaging a disturbance torque driven by two rear independent in-wheel motors of a 4WD micro electric vehicle.     

轮胎附着极限下差动制动对汽车横摆力矩的影响

本文以纵滑－侧偏联合工况的稳态轮胎模型为基础，分析了汽车极限转向条件下制动作用于不同车轮时对汽车横摆力矩的影响，并通过整车动力学仿真进行了验证，研究结果为利用差动制动控制提高汽车的高速操纵稳定性提供了动力学依据。     

Longitudinal Tire Dynamics

This article begins with a brief review of the traditional concept of lateral relaxation length. The review illustrates that this concept yields a useful approximation which can be used with semi-empirical tire models which assume lateral forces are a function of steady-state slip angles. The article then presents an analogous derivation for longitudinal slip. Like its lateral counterpart, the derivation yields an approximation for transient longitudinal slip which can be used with tire models which assume longitudinal forces are a function of steady-state longitudinal slip. It is shown that, like the relaxation-length-based lateral slip angle, this formulation for longitudinal slip yields the ability to compute shear forces at the tire/road interface for either high or low speed applications, a necessary feature of simulations which support human in the loop driving simulation. Like traditional kinematically-based longitudinal slip, the transient formulation presented here is coupled with the wheel spin equation, and it shares the characteristic that it is very stiff compared to the equations of vehicle motion. This characteristic is a challenge impeding the real-time calculations required for driving simulation. The paper shows that local linearization of the wheel spin equations coupled with analytical solutions of the transient longitudinal slip formulation provide the basis for both insight into the longitudinal dynamics of the tire and for integrating the model in real-time.     

轮胎动力学特性仿真分析研究

分析了各种常用轮胎模型的特点与应用范围,根据汽车操纵动力学研究的需求,在Matlab环境下运用魔术公式建立了轮胎动力学模型,并对汽车轮胎力与纵向滑移率,纵向力、侧向力及回正力矩与纵向滑移率、侧偏角、外倾角、垂直载荷的关系等轮胎特性进行了仿真分析,实验结果表明,魔术公式轮胎动力学模型可以较好地模拟轮胎的动力学特性,适用于车辆动力学研究领域。     

Longitudinal Tire Dynamics

SUMMARY

This article begins with a brief review of the traditional concept of lateral relaxation length. The review illustrates that this concept yields a useful approximation which can be used with semi-empirical tire models which assume lateral forces are a function of steady-state slip angles. The article then presents an analogous derivation for longitudinal slip. Like its lateral counterpart, the derivation yields an approximation for transient longitudinal slip which can be used with tire models which assume longitudinal forces are a function of steady-state longitudinal slip. It is shown that, like the relaxation-length-based lateral slip angle, this formulation for longitudinal slip yields the ability to compute shear forces at the tire/road interface for either high or low speed applications, a necessary feature of simulations which support human in the loop driving simulation. Like traditional kinematically-based longitudinal slip, the transient formulation presented here is coupled with the wheel spin equation, and it shares the characteristic that it is very stiff compared to the equations of vehicle motion. This characteristic is a challenge impeding the real-time calculations required for driving simulation. The paper shows that local linearization of the wheel spin equations coupled with analytical solutions of the transient longitudinal slip formulation provide the basis for both insight into the longitudinal dynamics of the tire and for integrating the model in real-time.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

Integrated Control of Active Rear Wheel Steering and Direct Yaw Moment Control

SUMMARY

An integrated control system of active rear wheel steering (4WS) and direct yaw moment control (DYC) is presented in this paper. Because of the tire nonlinearity that is mainly due to the saturation of cornering forces, vehicle handling performance is improved but limited to a certain extent only by steering control. Direct yaw moment control using braking and/or driving forces is effective not only in linear but also nonlinear ranges of tire friction circle. The proposed control system is a model matching controller which makes the vehicle follow the desired dynamic model by the state feedback of both yaw rate and side slip angle. Various computer simulations are carried out and show that vehicle handling performance is much improved by the integrated control system.     

Drive control system design for stability and maneuverability of a 6WD/6WS vehicle

This paper describes a drive controller designed to improve the lateral vehicle stability and maneuverability of a 6-wheel drive / 6-wheel steering (6WD/6WS) vehicle. The drive controller consists of upper and lower level controllers. The upper level controller is based on sliding control theory and determines both front and middle steering angle, additional net yaw moment, and longitudinal net force according to the reference velocity and steering angle of a manual drive, remotely controlled, autonomous controller. The lower level controller takes the desired longitudinal net force, yaw moment, and tire force information as inputs and determines the additional front steering angle and distributed longitudinal tire force on each wheel. This controller is based on optimal distribution control and takes into consideration the friction circle related to the vertical tire force and friction coefficient acting on the road and tire. Distributed longitudinal/lateral tire forces are determined as proportion to the size of the friction circle according to changes in driving conditions. The response of the 6WD/6WS vehicle implemented with this drive controller has been evaluated via computer simulations conducted using the Matlab/Simulink dynamic model. Computer simulations of an open loop under turning conditions and a closed-loop driver model subjected to double lane change have been conducted to demonstrate the improved performance of the proposed drive controller over that of a conventional DYC.     

Comparative study of vehicle tyre–road friction coefficient estimation with a novel cost-effective method

This paper qualitatively and quantitatively reviews and compares three typical tyre–road friction coefficient estimation methods, which are the slip slope method, individual tyre force estimation method and extended Kalman filter method, and then presents a new cost-effective tyre–road friction coefficient estimation method. Based on the qualitative analysis and the numerical comparisons, it is found that all of the three typical methods can successfully estimate the tyre force and friction coefficient in most of the test conditions, but the estimation performance is compromised for some of the methods during different simulation scenarios. In addition, all of these three methods need global positioning system (GPS) to measure the absolute velocity of a vehicle. To overcome the above-mentioned problem, a novel cost-effective estimation method is proposed in this paper. This method requires only the inputs of wheel angular velocity, traction/brake torque and longitudinal acceleration, which are all easy to be measured using available sensors installed in passenger vehicles. By using this method, the vehicle absolute velocity and slip ratio can be estimated by an improved nonlinear observer without using GPS, and the friction force and tyre–road friction coefficient can be obtained from the estimated vehicle velocity and slip ratio. Simulations are used to validate the effectiveness of the proposed estimation method.     

Electronic stability control for electric vehicle with four in-wheel motors

The electric vehicle with four direct-driven in-wheel motors is an over actuated system. A three-level control strategy of electronic stability control (ESC) is proposed to achieve optimal torque distribution for four in-wheel motors. The first level is a gain-scheduled linear quadratic regulator which is designed to generate the desired yaw moment command for ESC. Control allocation is the second level which is used to distribute the desired longitudinal tire forces according to the yaw moment command while satisfying the driver’s intent for acceleration and deceleration. The associated weighting matrix is designed using the work load ratio at each wheel to prevent saturating the tire. The third level is slip ratio control (SRC) which is employed at each wheel to generate the desired longitudinal tire force based on a combined-slip tire model. Simulation results show that the proposed method can enhance the ESC performance for the test maneuvers. Since the tire model is often unknown for practical implementation, the effectiveness of the SRC is studied using the sine with dwell test. It is found that the SRC is not crucial for achieving performance similar to the proposed method with SRC, if the slip ratio can be maintained in the stable region using traction control system/anti-lock braking system.     

Independent Suspension, Self Steered Axle, and 4WS for Busses

The dynamic behavior of commercial vehicles fitted with differentr types of suspension mechanisms and steering devices is investigated in this paper. Six vehicle models have been constructed: 2WS-SA is a standard two wheel steering bus with solid axles; 2WS-DW is a 2WSA vehicle with independent double wishbone suspension in front and rear axles; SSA-SA is a 2WS system with solid axles, the rear one being mounted on a self steered mechanism; SSA-DW is a vehicle with independent double wishbone suspension in the front axle, and a solid self steered rear axle; 4WS-SA has four wheel steering with solid axles; and 4WS-DW is a 4WS vehicle with independent double wishbone suspension in front and rear axles. The dynamic response of these models has been assessed in terms of lateral acceleration, yaw velocity, tire forces, tire force reserves, and slip angles. The expected advantages of a 4WS system (higher acceleration rates and lower slip angles) will be corroborated but, at the same time, it will be shown that they are obtained at the cost of lower force reserves. Self steered mechanisms produce smaller body slip angles, but it will be shown that they give rise to larger yaw velocity overshootings. The particular independent suspension analyzed does not show significant improvements with respect to the solid axle counterpart.     

Estimation of maximum road friction coefficient based on Lyapunov method

With the real time and accurate information of motor torque and rotation speed of the four-in-wheel-motordrive electric vehicles, a slip based algorithm for estimating maximum road friction coefficient is designed using Lyapunov stability theory. Modified Burckhardt tire model is used to describe longitudinal slip property of the tire. By introducing a new state variable, a nonlinear estimator is proposed to estimate the longitudinal tire force and the maximum road friction coefficient simultaneously. With the appropriate selection of estimation gain, the convergence of the estimation error of the tire longitudinal force and maximum road friction coefficient is proved through Lyapunov stability analysis. In addition, the error is exponentially stable near the origin. Finally the method is validated with Carsim-Simulink co-simulation and real vehicle tests under multi working conditions in acceleration situation which demonstrate high computational efficiency and accuracy of this method.     

基于NMPC的智能汽车纵横向综合轨迹跟踪控制

本文中针对大曲率转弯工况下,智能汽车纵横向动力学特性的耦合和动力学约束导致轨迹跟踪精度和稳定性下降的问题,提出一种基于非线性模型预测控制(NMPC)的纵横向综合轨迹跟踪控制方法,通过NMPC和障碍函数法(BM)的有效结合,提高了跟踪精度,改善了行驶稳定性.首先建立四轮驱动-前轮转向智能汽车动力学模型和轨迹跟踪模型,采用...     

A Versatile Flat Track Tire Testing Machine

Summary A flat track tire testing machine developed by the IMMa group is described. It permits the simulation and study of the dynamic behavior of a great variety of tires under controllable and repetitive highly dynamic realistic working conditions in the laboratory for a diversity of vehicles, from motorcycles to light trucks. The machine incorporates: – a hydraulically operated tire support and loading system with wide operating ranges; – a computer controlled brake system to simulate braking maneuvers with ABS systems; – a complete sensorial system; – a data acquisition and control system continually monitoring and acting on the experimental variables, i.e., tire and belt speed, longitudinal slip, slip and camber angles, tire pressure, tire normal force, etc. As an application example, results are presented that adjust the parameter of the magic formula for a standard 175/70 R14 passenger vehicle tire. Accurate mathematical tire models are recognized as essential for the prediction of vehicle dynamic performances using simulation tools.     

A Versatile Flat Track Tire Testing Machine

Summary A flat track tire testing machine developed by the IMMa group is described. It permits the simulation and study of the dynamic behavior of a great variety of tires under controllable and repetitive highly dynamic realistic working conditions in the laboratory for a diversity of vehicles, from motorcycles to light trucks. The machine incorporates: - a hydraulically operated tire support and loading system with wide operating ranges; - a computer controlled brake system to simulate braking maneuvers with ABS systems; - a complete sensorial system; - a data acquisition and control system continually monitoring and acting on the experimental variables, i.e., tire and belt speed, longitudinal slip, slip and camber angles, tire pressure, tire normal force, etc. As an application example, results are presented that adjust the parameter of the magic formula for a standard 175/70 R14 passenger vehicle tire. Accurate mathematical tire models are recognized as essential for the prediction of vehicle dynamic performances using simulation tools.     

Analytical dynamic tire model

Modeling of tire friction is one of the central problems for vehicle control systems design. LuGre-type dynamic tire model has been proposed and well discussed in previous studies, because it offers a compact form of dynamic model that is convenient in advanced control studies. It has been successfully used in tire slip control design and vehicle state estimation problems. In this article, a concept of time-constrained Stribeck effect is introduced to interpret the mechanism of the LuGre friction model in predicting tire friction characteristics. A modified two-dimensional (2D) dynamic LuGre friction model is introduced to make it compatible with the governing theorem in the steady state. An analytical 2D modified LuGre-type dynamic tire model is developed, in which some fundamental limitations of classical LuGre models are eliminated. The main modifications involve a change in the structure of the 2D LuGre friction model, introduction of load-dependent parameters in 1D and 2D tire models, and a changed structure in the distributed parameter model. The proposed model is compared, in the steady state, to both the Magic Formula and the classical LuGre model. It improves model accuracy in the steady state and gives a physically reasonable distribution of the bristle deflection. A first-order lumped parameter (LP) nonlinear model, which has simpler structure than the distributed parameter model and the classical LP LuGre model, is then derived. Numerical simulations show that the proposed LP model has a good estimation for tire transient dynamics. Thus, the proposed model retains the merits of LuGre-type models and improves the agreement with observation and experimental data on friction force distribution along the patch and on the steady-state friction prediction.     

Messungen von Fahrbahn-Unebenheiten paralleler Fahrspuren und Anwendung der Ergebnisse

Measurement of two track road inputs and theoretical application of the results

The calculation of vehicle response to road-surface irregularity inputs requires the spectral densities of the left and right longitudinal track and their statistical dependence

This paper presents some resluts of parallel profile measurements, three typical german roads have been chosen

Random vibration of two vehicle types are digital-simulated. The dynamic tire load shows that independent suspension systems are more advantageous than beam axles, because by wheel tramp this type increases the dynamic tire load.     

Analytical dynamic tire model

Modeling of tire friction is one of the central problems for vehicle control systems design. LuGre-type dynamic tire model has been proposed and well discussed in previous studies, because it offers a compact form of dynamic model that is convenient in advanced control studies. It has been successfully used in tire slip control design and vehicle state estimation problems. In this article, a concept of time-constrained Stribeck effect is introduced to interpret the mechanism of the LuGre friction model in predicting tire friction characteristics. A modified two-dimensional (2D) dynamic LuGre friction model is introduced to make it compatible with the governing theorem in the steady state. An analytical 2D modified LuGre-type dynamic tire model is developed, in which some fundamental limitations of classical LuGre models are eliminated. The main modifications involve a change in the structure of the 2D LuGre friction model, introduction of load-dependent parameters in 1D and 2D tire models, and a changed structure in the distributed parameter model. The proposed model is compared, in the steady state, to both the Magic Formula and the classical LuGre model. It improves model accuracy in the steady state and gives a physically reasonable distribution of the bristle deflection. A first-order lumped parameter (LP) nonlinear model, which has simpler structure than the distributed parameter model and the classical LP LuGre model, is then derived. Numerical simulations show that the proposed LP model has a good estimation for tire transient dynamics. Thus, the proposed model retains the merits of LuGre-type models and improves the agreement with observation and experimental data on friction force distribution along the patch and on the steady-state friction prediction.