Effect of Traction Force Distribution Control on Vehicle Dynamics

SUMMARY

The purpose of this study is to clarify vehicle dynamics effected by traction force distribution, not only between the front and rear wheels but also between the left and right wheels. Contribution of traction force distribution to vehicle turning performance was investigated using a mathematical simulation and an experimental vehicle. The results indicates that the control of traction control distribution between the left and right wheels greatly influences vehicle turning characteristics and improve the performance even in a marginal turning condition.     

Direct yaw moment control and power consumption of in-wheel motor vehicle in steady-state turning

Driving force distribution control is one of the characteristic performance aspects of in-wheel motor vehicles and various methods have been developed to control direct yaw moment while turning. However, while these controls significantly enhance vehicle dynamic performance, the additional power required to control vehicle motion still remains to be clarified. This paper constructed new formulae of the mechanism by which direct yaw moment alters the cornering resistance and mechanical power of all wheels based on a simple bicycle model, including the electric loss of the motors and the inverters. These formulation results were validated by an actual test vehicle equipped with in-wheel motors in steady-state turning. The validated theory was also applied to a comparison of several different driving force distribution mechanisms from the standpoint of innate mechanical power.     

电动汽车转矩定向分配差速器建模与动态仿真

本文中提出一种新型具备转矩定向分配功能差速器的集中式电驱动桥系统。该集中驱动系统可以在不改变总驱动转矩的条件下,类似分布式驱动方式实现驱动转矩在左右轮间的任意分配,从而产生改变车辆横摆动力学的直接横摆力偶矩。首先,分析了转矩定向分配差速器结构特点及其工作原理;其次,利用键合图理论建立了其动力学模型,并仿真分析了其动态响应特性;然后,设计了转矩响应控制系统以改善该差速器的动态性能;最后,嵌入整车模型进行了联合仿真。结果表明,装备该差速器的车辆可任意分配左右轮驱动转矩,并有效改善车辆操控特性。     

SL6400A轻型客车驻车制动传动机构的改进

SL6400A轻型客车驻车制动器采用后桥车轮鼓式制动器，该车原驻车制动机构存在传动环节多、支座刚性差及拉索走向不合理等因素，致使左、右后轮制动力不平衡或不足，通过分析与对比，自行设计了一种新型驻车制动传动机构，该结构可通过平衡器的转动保证左、右后轮制动力不平衡或不足，通过分析与对比，自行设计了一种新型驻车制动传动机构，该结构可通过平衡器的转动保证左、右后拉索拉力相等。试验证明，驻车制动效果良好。     

混凝土搅拌运输车行驶稳定性分析

针对混凝土搅拌运输车在行驶过程中,由混凝土偏心力矩引起整车重心位置变化,从而对车辆的行驶稳定性、车辆两侧轮胎所受载荷及拐弯行驶侧翻临界速度造成的影响进行分析,得到车辆在各种行驶状况下左右轮的承载百分比、车辆在拐弯状况下的侧翻临界速度和安全车速。结果表明：在行驶过程中,右旋搅拌车左右轮胎负荷较均匀;在拐弯半径一定的条件下,左旋车左拐弯最易翻车,右旋车右拐弯次之,拐弯时应在安全车速范围内行驶。     

Improvement of Vehicle Maneuverability by Direct Yaw Moment Control

This paper deals with a study to theoretically formulate an effective method of improving vehicle performance, particularly, its characteristics in the nonlinear region, and to verify the feasibility of the proposed method by calculations and examinations. In order to analyze vehicle characteristics in the nonlinear region, a new method of analysis was developed for determining yaw moment and side force of the vehicle with a parameter of the side slip angle at the center of gravity when its center of gravity point was fixed. The study with this new method found that direct yaw moment control by proper distribution of traction and braking forces on the right and left tires could provide a very effective means of stabilizing vehicle characteristics, specifically for acceleration and deceleration, and enlarging the limit of vehicle maneuverability.     

Multi-axle vehicle dynamics stability control algorithm with all independent drive wheel

The stability driving characteristic and the tire wear of 8-axle vehicle with 16-independent driving wheels are discussed in this paper. The lateral stability of 8-axle vehicle can be improved by the direct yaw moment which is generated by the 16 independent driving wheels. The hierarchical controller is designed to determine the required yaw torque and driving force of each wheel. The upper level controller uses feed-forward and feed-backward control theory to obtain the required yaw torque. The fuzzification weight ratio of two control objective is built in the upper level controller to regulate the vehicle yaw and lateral motions. The rule-based yaw moment distribution strategy and the driving force adjustment based on the safety of vehicle are proposed in the lower level controller. The influence of rear steering angle is considered in the distribution of driving force of the wheel. Simulation results of a vehicle double lane change show the stability of 8-axle vehicle under the proposed control algorithm. The wear rate of tire is calculated by the interaction force between the tire and ground. The wear of tire is different from each other for the vehicle with the stability controller or not.     

Improvement of Vehicle Maneuverability by Direct Yaw Moment Control

SUMMARY

This paper deals with a study to theoretically formulate an effective method of improving vehicle performance, particularly, its characteristics in the nonlinear region, and to verify the feasibility of the proposed method by calculations and examinations. In order to analyze vehicle characteristics in the nonlinear region, a new method of analysis was developed for determining yaw moment and side force of the vehicle with a parameter of the side slip angle at the center of gravity when its center of gravity point was fixed. The study with this new method found that direct yaw moment control by proper distribution of traction and braking forces on the right and left tires could provide a very effective means of stabilizing vehicle characteristics, specifically for acceleration and deceleration, and enlarging the limit of vehicle maneuverability.     

Real-time implementation of a traction control algorithm on a scaled roller rig

Traction control is a very important aspect in railway vehicle dynamics. Its optimisation allows improvement of the performance of a locomotive by working close to the limit of adhesion. On the other hand, in case the adhesion limit is surpassed, the wheels are subjected to heavy wear and there is also a big risk that vibrations in the traction occur. Similar considerations can be made in the case of braking. The development and optimisation of a traction/braking control algorithm is a complex activity, because it is usually performed on a real vehicle on the track, where many uncertainties are present due to environmental conditions and vehicle characteristics. This work shows the use of a scaled roller rig to develop and optimise a traction control algorithm on a single wheelset. Measurements performed on the wheelset are used to estimate the optimal adhesion forces by means of a wheel/rail contact algorithm executed in real time. This allows application of the optimal adhesion force.     

Optimal motion control for collision avoidance at Left Turn Across Path/Opposite Direction intersection scenarios using electric propulsion

Collision avoidance at intersections involving a host vehicle turning left across the path of an oncoming vehicle (Left Turn Across Path/Opposite Direction) have been studied in the past, but mostly using simplified interventions and rarely considering the possibility of crossing the intersection ahead of a bullet vehicle. Such a scenario where the driver preference is to avoid a collision by crossing the intersection ahead of a bullet vehicle is considered in this work. The optimal vehicle motion for collision avoidance in this scenario is determined analytically using a particle model within an optimal control framework. The optimal manoeuvres are then verified through numerical optimisations using a two-track vehicle model, where it was seen that the wheel forces followed the analytical global force angle result independently of the other wheels. A Modified Hamiltonian Algorithm controller for collision avoidance that uses the analytical optimal control solution is then implemented and tested in CarMaker simulations using a validated Volvo XC90 vehicle model. Simulation results showed that collision risk can be significantly reduced in this scenario using the proposed controller, and that more benefit can be expected in scenarios that require larger speed changes.     

Modelling and control of a new differential steering concept

This paper presents a new steer-by-wire concept using an all-wheel drive vehicle layout with in-wheel motors while completely omitting the application of any dedicated steering device. Steering is based on the so-called differential steering principle which generates the necessary steering moment about the kingpins by a traction force difference between left and right sides of the vehicle. In order to investigate the behaviour of the vehicle and to design the underlying control algorithms, a planar vehicle model is presented, where the vehicle is described as constrained non-holonomic system requiring a special treatment. A state feedback linear controller for controlling of the lateral dynamics of the vehicle at higher speeds and a simple PI angle controller for low-speed manoeuvring are developed. The resulting behaviour of the system is investigated by various simulation experiments demonstrating a comparable steering performance of the new steering concept as that of conventional passenger cars.     

轿车前后轴制动力平衡分布研究

基于大量轿车前后轴制动力实测数据，运用数理统计手段，研究确定国产主要轿车前后轴制动车平衡分布规律及分布参数，进而建立相应车型的前后轴制动力平衡分布计算模型，本文研究对从统计规律上掌握国产轿车前后轴承动力平衡性能和准确地计算相应的分布数值具有十分重要的意义。     

Sliding mode-based lateral vehicle dynamics control using tyre force measurements

In this work, a lateral vehicle dynamics control based on tyre force measurements is proposed. Most of the lateral vehicle dynamics control schemes are based on yaw rate whereas tyre forces are the most important variables in vehicle dynamics as tyres are the only contact points between the vehicle and road. In the proposed method, active front steering is employed to uniformly distribute the required lateral force among the front left and right tyres. The force distribution is quantified through the tyre utilisation coefficients. In order to address the nonlinearities and uncertainties of the vehicle model, a gain scheduling sliding-mode control technique is used. In addition to stabilising the lateral dynamics, the proposed controller is able to maintain maximum lateral acceleration. The proposed method is tested and validated on a multi-body vehicle simulator.     

越野汽车TCS冰雪道路试验研究

针对自主开发的越野汽车牵引力控制系统（TCS）进行了冰雪路面加速道路试验研究，完成了实际“驾驶员-车辆-道路”闭环环境下的TCS的软、硬件匹配。试验结果表明：牵引力控制系统能够有效消除驱动轮过度滑转，显著改善汽车的加速性和方向稳定性。     

基于NMPC的智能汽车纵横向综合轨迹跟踪控制

本文中针对大曲率转弯工况下,智能汽车纵横向动力学特性的耦合和动力学约束导致轨迹跟踪精度和稳定性下降的问题,提出一种基于非线性模型预测控制(NMPC)的纵横向综合轨迹跟踪控制方法,通过NMPC和障碍函数法(BM)的有效结合,提高了跟踪精度,改善了行驶稳定性.首先建立四轮驱动-前轮转向智能汽车动力学模型和轨迹跟踪模型,采用...     

基于理想制动力分配曲线的复合制动设计

以理想制动力分配曲线为目标,在车辆液压制动力分配系数保持不变的情况下,研究了前后液压制动力和再生制动力分配的比例关系,确定了制动力分配控制策略;在确保液压制动力分配系数满足法规要求的情况下,以最优制动力分配为目标优化了整车结构参数。     

Influence of the transmission configuration of a multiple axle vehicle on the obstacle surmounting capacity

Conventional wheeled vehicles have serious mobility limitations in rough terrain while walking vehicles have inherent drawbacks such as a high number of DOF and actuators, control complexity and low-energy efficiency. Vehicles that passively adapt the position of multiple wheels to maintain contact with the ground can be a good compromise between both conventional wheeled and walking vehicles. One way to increase the number of wheels in contact with the ground is using bogies. However, the kinematics of a multiple axle vehicle moving on irregular terrain is quite complex since every wheel can require different angular speed to avoid slippage. The present work aims to quantify the obstacle surmounting capacity of a four axle, double-bogie vehicle depending on the transmission configuration, since it can provoke the slippage of some of its wheels.

Some results are presented corresponding to the vehicle moving on a straight upward slope of different angles and facing variable obstacles in any of its axles.

It can be observed that as more restricted the transmission is, more wheels are forced to slip and less traction the vehicle has, and, as a consequence, less obstacle surmounting capacity.     

独立轮电驱动车辆主动操纵稳定控制研究

提出了采用变增益参考模型的滑模跟踪控制策略,以横摆角速度和侧滑速度为控制对象,独立控制左右轮驱动力产生直接横摆力矩,提高了车辆在极限工况下的操纵稳定性,并改善了车辆固有的转向特性。改进的滑模控制算法减小了系统抖振并具有较强的鲁棒性。     

A novel fuzzy logic correctional algorithm for traction control systems on uneven low-friction road conditions

The traction control system (TCS) might prevent excessive skid of the driving wheels so as to enhance the driving performance and direction stability of the vehicle. But if driven on an uneven low-friction road, the vehicle body often vibrates severely due to the drastic fluctuations of driving wheels, and then the vehicle comfort might be reduced greatly. The vibrations could be hardly removed with traditional drive-slip control logic of the TCS. In this paper, a novel fuzzy logic controller has been brought forward, in which the vibration signals of the driving wheels are adopted as new controlled variables, and then the engine torque and the active brake pressure might be coordinately re-adjusted besides the basic logic of a traditional TCS. In the proposed controller, an adjustable engine torque and pressure compensation loop are adopted to constrain the drastic vehicle vibration. Thus, the wheel driving slips and the vibration degrees might be adjusted synchronously and effectively. The simulation results and the real vehicle tests validated that the proposed algorithm is effective and adaptable for a complicated uneven low-friction road.     

重型汽车低附着路面制动稳定性的仿真研究

文章利用trucksim重型汽车动力学仿真软件,对六轮双轴重型汽车在低附着路面左右车轮附着系数不一致情况下进行紧急制动的行驶工况进行了仿真研究。研究结果表明在低附着路面进行紧急制动时,对制动轮进行制动压力控制,有ABS控制的重型汽车比没有ABS控制的重型汽车具有更好地行驶稳定性。但在低附着路面上,有ABS控制的重型汽车比没有ABS控制的重型汽车的制动距离增加了很多,这对重型汽车的行车安全性非常不利。