A traffic noise model for road intersections in the city of Cartagena de Indias,Colombia

Road traffic noise models are fundamental tools for designing and implementing appropriate prevention plans to minimize and control noise levels in urban areas. The objective of this study is to develop a traffic noise model to simulate the average equivalent sound pressure level at road intersections based on traffic flow and site characteristics, in the city of Cartagena de Indias (Cartagena), Colombia. Motorcycles are included as an additional vehicle category since they represent more than 30% of the total traffic flow and a distinctive source of noise that needs to be characterized. Noise measurements are collected using a sound level meter Type II. The data analysis leads to the development of noise maps and a general mathematical model for the city of Cartagena, Colombia, which correlates the sound levels as a function of vehicle flow within road intersections. The highest noise levels were 79.7 dB(A) for the road intersection María Auxiliadora during the week (business days) and 77.7 dB(A) for the road intersection India Catalina during weekends (non-business days). Although traffic and noise are naturally related, the intersections with higher vehicle flow did not have the highest noise levels. The roadway noise for these intersections in the city of Cartagena exceeds current limit standards. The roadway noise model is able to satisfactorily predict noise emissions for road intersections in the city of Cartagena, Colombia.     

An experimental study of the effect of low-noise wheels in reducing noise and vibration

Wheel/rail interaction is a major source of railway noise. A low-noise wheel structure is developed and its effect on noise reduction is investigated. This low-noise wheel employs a rubber material inserted into the steel rim or mounted on the wheel surface. The low-noise wheel has low stiffness and a high-damping ratio compared to a solid wheel. Measurement shows that it reduces rolling and squealing. It turns out that a subway line with the proposed wheel could reduce its interior noise level by 4–5 dB(A) and vehicle vibration level by 7–8 dB. While the proposed structure seems promising in noise reduction for railway vehicles, the endurance and cost effectiveness of the low-noise wheel are yet to be verified.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

Comparisons of the environmental footprint of heavy vehicles in the UK and Switzerland

The European Union project Eureka Logchain Footprint is an ongoing project to identify road and rail vehicles by means of their environmental footprint as characterised by dynamic load, noise, ground borne vibrations and gaseous emissions induced by the vehicle. Part of the project involves the installation of road and rail footprint monitoring stations throughout Europe. This paper presents results of the road stations in Switzerland and the UK. Individual vehicle data from weigh-in-motion and noise are compared. The results indicate that a significant number of vehicles surpass the limits set in both countries. It was shown that the UK sites are generating higher noise levels than their Swiss counterparts; in part due to the much coarser aggregate embedded in the running course of the pavement employed in the UK. Such data can be used to create an incentive for vehicle types with a low footprint and a penalty for vehicles with a large footprint.     

Noise level in the vicinity of signalized roundabouts

The analysis, assessment and estimation of noise levels in the vicinity of intersections is a more complex problem than a similar analysis for roads and streets. This is due to the varied geometry of the intersections, differences in the loads of individual movements, participation of heavy vehicles and mass transport vehicles, as well as the various types of traffic management and traffic control. This article analyses the influence of intersection type and traffic characteristics on the noise levels in the vicinity of classic channelized intersections with signalization, roundabouts and signalized roundabouts. Based on the conducted measurements, it has been established that, with comparable traffic parameters and the same distance from the geometric centre of the intersection, the L_Aeq value for signalized roundabouts is 2.5–10.8 dB higher in comparison to classic channelized intersections with signalization and 3.3–6.7 dB higher in relations to the analysed roundabout. Additionally the differences between L_Aeq levels at individual entries at the same signalized roundabouts may reach the value of approximately 4.5 dB. Such situation is influenced by differences in the intersection geometry, diameter of the intersection’s central island, traffic flow type, traffic management at the entries and traffic volume, especially the amount and traffic movements of multiple axle heavy vehicles. These factors have been analysed in detail in relation to signalized roundabouts in this paper.     

Characteristics of gaseous and particulate pollutants exhaust from logistics transportation vehicle on real-world conditions

On-road vehicle tests of three heavy duty diesel trucks were conducted by a portable emission measurement system (PEMS) in Chengdu, China. SEMTECH-ECOSTAR provided by Sensors Inc. was employed to detect gaseous emissions and MI2, an emissions measuring instrument powered by the Pegasor Particulate Sensor (PPS) was used to detect particulate emissions during the tests. The impacts of speed, acceleration and engine load on emissions were analyzed. The average nitrogen oxides (NOx) emission factors of the heavy duty diesel truck (HDDT), medium-duty diesel truck (MDDT), light duty diesel truck (LDDT) were 7.29, 5.29 and 5.53 g/km. The particulate emission factors were 0.60, 0.30 and 0.14 g/km respectively, higher than the similar reported in the previous studies. Both gaseous and particulate emission exhibit significant correlations with the change in vehicle speed, acceleration and power demand. The highest emission was generally in high VSPs and higher loads. High engine load caused by aggressive driving was the main factor of high emissions for the vehicles on real-world conditions.     

Age related annual crash incidence rate ratios in professional drivers of heavy goods vehicles

ObjectivesEvidence concerning crash risk for older heavy vehicle drivers is sparse, making it difficult to assess if it is prudent to encourage older drivers to remain in the workforce in a climate of labour shortages. The objective of this study was to estimate annual crash rate ratios of older male heavy vehicle drivers relative to their middle aged peers.MethodsData utilized in this study includes all crashes meeting inclusion criteria involving heavy goods vehicles, categorised as rigid trucks and articulated trucks; this data was recorded by the New South Wales Roads and Traffic Authority. The exposure to the risk of a crash was represented by distance travelled for each vehicle type and year, by age of driver, as estimated by the Australian Survey of Motor Vehicle Use. Negative binomial regression modelling was applied to estimate annual crash incidence rate ratios for male drivers in various age groups.ResultsA total of 26,146 crashes occurred in New South Wales during 1999–2006, involving a total of 54,191 vehicles; removing observations that did not meet the inclusion criteria, 19,736 observations remained representing 12,501 crashes. For rigid trucks, the incidence rate ratio for drivers aged 65+ years, compared to 45–54 year olds, was 0.74 (95% CI 0.51, 0.98). For articulated trucks, the annual crash incidence rate ratio for drivers aged 65+ years compared to 45–54 year olds was 1.4 (95% CI 0.96, 1.9), and that for drivers aged 55–64 years compared to 45–54 year olds was 1.1 (95% CI 0.83, 1.3).ConclusionsOlder male professional drivers of heavy goods vehicles have lower risk of crashes in rigid vehicles, possibly due to accrued driving experience and self-selection of healthy individuals remaining in the workforce. Thus, encouraging these drivers to remain in the workforce is appropriate in the climate of labour shortages, as this study provides evidence that to do so would not endanger road safety.     

Integrated vehicle and powertrain optimization for passenger vehicles with vehicle-infrastructure communication

This research proposes an optimal controller to improve fuel efficiency for a vehicle equipped with automatic transmission traveling on rolling terrain without the presence of a close preceding vehicle. Vehicle acceleration and transmission gear position are optimized simultaneously to achieve a better fuel efficiency. This research leverages the emerging Connected Vehicle technology and utilizes present and future information—such as real-time dynamic speed limit, vehicle speed, location and road topography—as optimization input. The optimal control is obtained using the Relaxed Pontryagin’s Minimum Principle. The benefit of the proposed optimal controller is significant compared to the regular cruise control and other eco-drive systems. It varies with the hill length, grade, and the number of available gear positions. It ranges from an increased fuel saving of 18–28% for vehicles with four-speed transmission and 25–45% for vehicles with six-speed transmission. The computational time for the optimization is 1.0–2.1 s for the four-speed vehicle and 1.8–3.9 s for the six-speed vehicle, given a 50 s optimization time horizon and 0.1 s time step. The proposed controller can potentially be used in real-time.     

Integrated analysis of GHGs and public health damage mitigation for developing urban road transportation strategies

This study attempts to present an urban road transportation strategy focusing on the mitigation of both GHGs emission and public health damage, taking Xiamen City as a case study. We developed a Public Health and GHGs Emission model to estimate the impacts of direct energy-consumption-related GHGs emissions and public health damage in Xiamen’s road transportation strategies from 2008 to 2025, considering the environmental benefits and economic costs. Two scenarios were designed to describe future transportation strategies for Xiamen City, and mitigation potentials for both GHGs emission and public health costs were estimated from 2008 to 2025 under a series of options. The results show that enacting controls on private vehicles would be most effective to GHGs mitigation, while enacting controls on government and rental vehicles would contribute the most to NO₂ and PM2.5 reductions. Compared with the Business as Usual scenario, the Integrated scenario would achieve about a 68% energy consumption reduction and save 0.23 billion yuan (95% CI: 0.16, 0.32) in health costs in 2025. It is clear that integrated and advisable strategies need to mitigate the adverse impacts of urban road vehicles on GHGs emissions and public health and economic costs, particularly in regions of rapid urbanization.     

Are HOV/eco-lanes a sustainable option to reducing emissions in a medium-sized European city?

Innovative traffic management measures are needed to reduce transportation-related emissions. While in Europe, road lane management has focused mainly on introduction of bus lanes, the conversion to High Occupancy Vehicles (HOV) and eco-lanes (lanes dedicated to vehicles running on alternative fuels) has not been studied comprehensively. The objectives of this research are to: (1) Develop an integrated microscopic modeling platform calibrated with real world data to assess both traffic and emissions impacts of future Traffic Management Strategies (TMS) in an urban area; (2) Evaluate the introduction of HOV/eco-lanes in three different types of roads, freeway, arterial and urban routes, in an European medium-sized city and its effects in terms of emissions and traffic performance. The methodology consists of three distinct phases: (a) Traffic and road inventory data collection; (b) Traffic and emissions simulation using an integrated platform of microscopic simulation; and (c) Evaluation of scenarios. For the baseline scenario, the statistical analysis shows valid results. The results show that HOV and eco-lanes in a medium European city are feasible, and when the Average Occupancy of Vehicles (AOV) increases, on freeways, the majority of vehicles can reduce their travel time (2%) with a positive impact in terms of total emissions (−38% NO_x, −39% HC, −43% CO and −37% CO₂). On urban and arterial corridors, the reduction in emissions could be achieved only if the AOV increases from 1.50 to 1.70 passengers/vehicle. Total emissions of the corridor with an AOV of 1.70 passengers/vehicle can be reduced up to 35–36% for the urban route while the values can be reduced by 36–39% for the arterial road. With the introduction of Hybrid Electric Vehicles (HEV) and Electric Vehicles (EV) it is possible to reduce emissions, although the introduction of eco-lanes did not show significant reductions in emissions. When both policies are simulated together, an emissions improvement is observed for the arterial route and for two of the scenarios.     

Effects of driving style on the fuel consumption of city buses under different road conditions and vehicle masses

The variance in fuel consumption caused by driving style (DS) difference exceeds 10% and reaches a maximum of 20% under different road conditions, even for experienced bus drivers. To study the influence of DS on fuel consumption, a method for summarizing DS characteristic parameters on the basis of vehicle-engine combined model is proposed. With this method, the author proposes 26 DS characteristic parameters related to fuel consumption in the accelerating, normal running, and decelerating processes of vehicles. The influence of DS characteristic parameters on fuel consumption under different road conditions and vehicle masses is quantitatively analyzed on the basis of real driving data over 100,000 km. Analysis results show that the influence of DS characteristic parameters on fuel consumption changes with road condition and vehicle mass, with road condition serving a more important function. However, the DS characteristics in the accelerating process of vehicles are decisive for fuel consumption under different conditions. This study also calculates the minimum sample size necessary for analyzing the effect of DS characteristics on fuel consumption. The statistical analysis based on the real driving data over 2500 km can determine the influence of DS on fuel consumption under a given power-train configuration and road condition. The analysis results can be employed to evaluate the fuel consumption of drivers, as well as to guide the design of Driver Advisory System for Eco-driving directly.     

Estimation of flow and density using probe vehicles with spacing measurement equipment

Probe vehicles provide some of the most useful data for road traffic monitoring because they can acquire wide-ranging and spatiotemporally detailed information at a relatively low cost compared with traditional fixed-point observation. However, current GPS-equipped probe vehicles cannot directly provide us volume-related variables such as flow and density. In this paper, we propose a new probe vehicle-based estimation method for obtaining volume-related variables by assuming that a probe vehicle can measure the spacing to its leading one. This assumption can be realized by utilizing key technologies in advanced driver assistance systems that are expected to spread in the near future. We developed a method of estimating the flow, density, and speed from the probe vehicle data without exogenous assumptions on traffic flow characteristics, such as a fundamental diagram. In order to quantify the characteristics of the method, we performed a field experiment at a real-world urban expressway by employing prototypes of the probe vehicles with spacing measurement equipment. The result showed that the proposed method could accurately estimate the 5 min and hourly traffic volumes with probe vehicle penetration rate of 3.5% and 0.2%, respectively.     

Effects of battery chemistry and performance on the life cycle greenhouse gas intensity of electric mobility

Lithium traction batteries are a key enabling technology for plug-in electric vehicles (PEVs). Traction battery manufacture contributes to vehicle production emissions, and battery performance can have significant effects on life cycle greenhouse gas (GHG) emissions for PEVs. To assess emissions from PEVs, a life cycle perspective that accounts for vehicle production and operation is needed. However, the contribution of batteries to life cycle emissions hinge on a number of factors that are largely absent from previous analyses, notably the interaction of battery chemistry alternatives and the number of electric vehicle kilometers of travel (e-VKT) delivered by a battery. We compare life cycle GHG emissions from lithium-based traction batteries for vehicles using a probabilistic approach based on 24 hypothetical vehicles modeled on the current US market. We simulate life-cycle emissions for five commercial lithium chemistries. Examining these chemistries leads to estimates of emissions from battery production of 194–494 kg CO₂ equivalent (CO₂e) per kWh of battery capacity. Combined battery production and fuel cycle emissions intensity for plug-in hybrid electric vehicles is 226–386 g CO₂e/e-VKT, and for all-electric vehicles 148–254 g CO₂e/e-VKT. This compares to emissions for vehicle operation alone of 140–244 g CO₂e/e-VKT for grid-charged electric vehicles. Emissions estimates are highly dependent on the emissions intensity of the operating grid, but other upstream factors including material production emissions, and operating conditions including battery cycle life and climate, also affect life cycle GHG performance. Overall, we find battery production is 5–15% of vehicle operation GHG emissions on an e-VKT basis.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.     

Reconstructing maximum likelihood trajectory of probe vehicles between sparse updates

Data from connected probe vehicles can be critical in estimating road traffic conditions. Unfortunately, current available data is usually sparse due to the low reporting frequency and the low penetration rate of probe vehicles. To help fill the gaps in data, this paper presents an approach for estimating the maximum likelihood trajectory (MLT) of a probe vehicle in between two data updates on arterial roads. A public data feed from transit buses in the city of San Francisco is used as an example data source. Low frequency updates (at every 200 m or 90 s) leaves much to be inferred. We first estimate travel time statistics along the road and queue patterns at intersections from historical probe data. The path is divided into short segments, and an Expectation Maximization (EM) algorithm is proposed for allocating travel time statistics to each segment. Then the trajectory with the maximum likelihood is generated based on segment travel time statistics. The results are compared with high frequency ground truth data in multiple scenarios, which demonstrate the effectiveness of the proposed approach, in estimating both the trajectory while moving and the stop positions and durations at intersections.     

Fuel savings on a heavy vehicle via aerodynamic drag reduction

In this numerical study, the fuel-saving potentials of drag-reducing devices retrofitted on heavy vehicles are analysed. Realistic on-road operations are taken into account by simulating typical driving routes on long-haul and urban distributions; variations in vehicle weight are also considered. Results show that the performance of these aerodynamic devices depend both on their functions and how the vehicles are operated. Vehicles on long-haul routes generally save twice as much fuel as those driven in urban areas. The fuel reductions from using selected devices individually on a large truck range from less than 1% to almost 9% of the fuel cost of a vehicle doing an annual mileage is 80,000 miles.     

The effect of time on acoustic durability of low noise pavements – The case studies in Poland

The tyre/road noise depends on type and speed of vehicles and on the characteristics of road pavement. Vehicle traffic load and weather conditions lead to significant changes in the characteristics of the materials used to build the wearing course. This applies especially to road pavements with the increased void contents. Clogging of the pores, changes in the characteristics of the binder and the damage to the wearing course influence changes in the acoustic properties of the road pavement over time. The article presents the results of the studies on noise level carried out in 2011 and 2014 by the Statistical Pass-By method (SPB) on porous asphalt concrete (PAC), very thin asphalt concrete (VTAC) and stone mastic asphalt (SMA). The wearing courses with the increased void contents immediately after building constitute a very advantageous solution compared with traditional road pavements (dense asphalt concrete, stone mastic asphalt). However, the unfavourable location of the road with porous wearing course, lack of systematic cleaning of porous layers or inappropriate maintenance methods in winter lead to the loss of the acoustic durability of low-noise pavements within a few years of their exploitation.     

Wireless charging in California: Range,recharge, and vehicle electrification

This research evaluated the potential for wireless dynamic charging (charging while moving) to address range and recharge issues of modern electric vehicles by considering travel to regional destinations in California. A 200-mile electric vehicle with a real range of 160 miles plus 40 miles reserve was assumed to be used by consumers in concert with static and dynamic charging as a strict substitute for gasoline vehicle travel. Different combinations of wireless charging power (20–120 kW) and vehicle range (100–300 miles) were evaluated. One of the results highlighted in the research indicated that travel between popular destinations could be accomplished with a 200-mile EV and a 40 kW dynamic wireless charging system at a cost of about $2.5 billion. System cost for a 200-mile EV could be reduced to less than $1 billion if wireless vehicle charging power levels were increased to 100 kW or greater. For vehicles consuming 138 kWh of dynamic energy per year on a 40 kW dynamic system, the capital cost of $2.5 billion plus yearly energy costs could be recouped over a 20-year period at an average cost to each vehicle owner of $512 per year at a volume of 300,000 vehicles or $168 per year at a volume of 1,000,000 vehicles. Cost comparisons of dynamic charging, increased battery capacity, and gasoline refueling were presented. Dynamic charging, coupled with strategic wayside static charging, was shown to be more cost effective to the consumer over a 10-year period than gasoline refueling at $2.50 or $4.00 per gallon. Notably, even at very low battery prices of $100 per kWh, the research showed that dynamic charging can be a more cost effective approach to extending range than increasing battery capacity.     

Isocyanic acid and ammonia in vehicle emissions

Vehicles are considered to be an important source of ammonia (NH₃) and isocyanic acid (HNCO). HNCO and NH₃ have been shown to be toxic compounds. Moreover, NH₃ is also a precursor in the formation of atmospheric secondary aerosols. For that reason, real-time vehicular emissions from a series of Euro 5 and Euro 6 light-duty vehicles, including spark ignition (gasoline and flex-fuel), compression ignition (diesel) and a plug-in electric hybrid, were investigated at 23 and −7 °C over the new World harmonized Light-duty vehicle Test Cycle (WLTC) in the Vehicle Emission Laboratory at the European Commission Joint Research Centre Ispra, Italy. The median HNCO emissions obtained for the studied fleet over the WLTC were 1.4 mg km⁻¹ at 23 °C and 6 mg km⁻¹ at −7 °C. The fleet median NH₃ emission factors were 10 mg km⁻¹ and 21 mg km⁻¹ at 23 and −7 °C, respectively. The obtained results show that even though three-way catalyst (TWC), selective catalytic reduction (SCR), and NOx storage catalyst (NSC) are effective systems to reduce NOx vehicular emissions, they also lead to considerable emissions of the byproducts NH₃ and/or HNCO. It is also shown that diesel light-duty vehicles equipped with SCR can present NH₃ emission factors as high as gasoline light-duty vehicles at both, 23 and −7 °C over the WLTC. Therefore, with the introduction in the market of this DeNOx technology, vehicular NH₃ emissions will increase further.