Investigating the applicability of exclusive pedestrian phase at two‐phase actuated controlled intersections

The exclusive pedestrian phase (EPP) has been used in many countries to promote walking around downtown areas by increasing the ease and convenience of pedestrian crossing. However, its applicability has not been systematically demonstrated, especially when an intersection is operated in actuated mode. This paper presents an extensive simulation‐based analysis of the applicability of EPP as compared with a normal concurrent pedestrian‐phase pattern at an isolated intersection controlled by actuated logic. Actuated signal control logics for EPP‐actuated and conventional concurrent pedestrian phase‐actuated controls are developed. Both of these control logics consider pedestrian crossing demands and can adapt to changes in vehicle traffic to reduce vehicle delay as well. A simulation model of a two‐phase controlled intersection is built and calibrated based on field data using VISSIM (PTV Planung Transport Verkehr AG in Karlsruhe, Germany). Extensive analysis is conducted to reveal fully the applicable EPP domain in terms of vehicle traffic demand, pedestrian demand, vehicle turning ratio, and pedestrian diagonal crossing ratio. The results show that the performance and applicable domain of EPP are jointly determined by those five factors. EPP significantly outperforms concurrent pedestrian phase if the vehicle turning ratio is greater than 0.6 and the pedestrian diagonal crossing ratio is greater than 0.6. These results can help traffic engineers in choosing the appropriate pedestrian‐phase patterns at actuated signalized intersections. Copyright © 2015 John Wiley & Sons, Ltd.     

Noise level in the vicinity of signalized roundabouts

The analysis, assessment and estimation of noise levels in the vicinity of intersections is a more complex problem than a similar analysis for roads and streets. This is due to the varied geometry of the intersections, differences in the loads of individual movements, participation of heavy vehicles and mass transport vehicles, as well as the various types of traffic management and traffic control. This article analyses the influence of intersection type and traffic characteristics on the noise levels in the vicinity of classic channelized intersections with signalization, roundabouts and signalized roundabouts. Based on the conducted measurements, it has been established that, with comparable traffic parameters and the same distance from the geometric centre of the intersection, the L_Aeq value for signalized roundabouts is 2.5–10.8 dB higher in comparison to classic channelized intersections with signalization and 3.3–6.7 dB higher in relations to the analysed roundabout. Additionally the differences between L_Aeq levels at individual entries at the same signalized roundabouts may reach the value of approximately 4.5 dB. Such situation is influenced by differences in the intersection geometry, diameter of the intersection’s central island, traffic flow type, traffic management at the entries and traffic volume, especially the amount and traffic movements of multiple axle heavy vehicles. These factors have been analysed in detail in relation to signalized roundabouts in this paper.     

An optimization method for sustainable traffic control in urban areas

The optimization of traffic signalization in urban areas is formulated as a problem of finding the cycle length, the green times and the offset of traffic signals that minimize an objective function of performance indices. Typical approaches to this optimization problem include the maximization of traffic throughput or the minimization of vehicles’ delays, number of stops, fuel consumption, etc. Dynamic Traffic Assignment (DTA) models are widely used for online and offline applications for efficient deployment of traffic control strategies and the evaluation of traffic management schemes and policies. We propose an optimization method for combining dynamic traffic assignment and network control by minimizing the risk of potential loss induced to travelers by exceeding their budgeted travel time as a result of deployed traffic signal settings, using the Conditional Value-at-Risk model. The proposed methodology can be easily implemented by researchers or practitioners to evaluate their alternative strategies and aid them to choose the alternative with less potential risk. The traffic signal optimization procedure is implemented in TRANSYT-7F and the dynamic propagation and route choice of vehicles is simulated with a mesoscopic dynamic traffic assignment tool (DTALite) with fixed temporal demand and network characteristics. The proposed approach is applied to a reference test network used by many researchers for verification purposes. Numerical experiments provide evidence of the advantages of this optimization method with respect to conventional optimization techniques. The overall benefit to the performance of the network is evaluated with a Conditional Value-at-Risk Analysis where the optimal solution is the one presenting the least risk for ‘guaranteed’ total travel times.     

Dynamic vehicular delay comparison between a police-controlled roundabout and a traffic signal

Effects of queues on motorists during rush hours are severe at intersections controlled by roundabouts. Traffic police are frequently used in order to optimize the traffic flow and to control queue length at such intersections. However, the question as to how efficient such system is, compared with traffic signal, is not clear from the dynamic delay point of view. In this study a criterion is being developed based on vehicular delays as the motorist join the queues and cross the stop-line. The adopted method avoids oversimplification of reality and prevents unrealistic assumptions. The data required for the study were mainly collected through video filming technique. The results, for a given set of geometric and traffic characteristics, indicate that both a police-controlled roundabout and a traffic signal act in a similar manner in terms of vehicular delay at a certain critical value. This critical value is considered to be the point of intersection between the curves representing traffic signal and roundabout on a delay–space diagram for the vehicles as they join the tail end of the queue until they cross the stop-line. Beyond the critical value, the effect of delays and buildup of queues at roundabouts will be excessive, compared to traffic signals. Before the critical value the delays at traffic signals are quite high compared to roundabouts. The study will assist the concerned authorities to operate the existing conditions, particularly the roundabouts, more efficiently. It will also be beneficial for the traffic planners and policy makers in making judicious decisions regarding control type at intersections.     

A model‐based demand‐balancing control for dynamically divided multiple urban subnetworks

Traffic control is an effective and efficient method for the problem of traffic congestion. It is necessary to design a high‐level controller to regulate the network traffic demands, because traffic congestion is not only caused by the improper management of the traffic network but also to a great extent caused by excessive network traffic demands. Therefore, we design a demand‐balance model predictive controller based on the macroscopic fundamental diagram‐based multi‐subnetwork model, which can optimize the network traffic mobility and the network traffic throughput by regulating the input traffic flows of the subnetworks. Because the transferring traffic flows among subnetworks are indirectly controlled and coordinated by the demand‐balance model predictive controller, the subnetwork division can variate dynamically according to real traffic states, and a global optimality can be achieved for the entire traffic network. The simulation results show the effectiveness of the proposed controller in improving the network traffic throughput. Copyright © 2016 John Wiley & Sons, Ltd.     

Self-organizing traffic signals using secondary extension and dynamic coordination

Actuated traffic signal control logic has many advantages because of its responsiveness to traffic demands, short cycles, effective use of capacity leading to and recovering from oversaturation, and amenability to aggressive transit priority. Its main drawback has been its inability to provide good progression along arterials. However, the traditional way of providing progression along arterials, coordinated–actuated control with a common, fixed cycle length, has many drawbacks stemming from its long cycle lengths, inflexibility in recovering from priority interruptions, and ineffective use of capacity during periods of oversaturation. This research explores a new paradigm for traffic signal control, “self-organizing signals,” based on local actuated control but with some additional rules that create coordination mechanisms. The primary new rules proposed are for secondary extensions, in which the green may be held to serve an imminently arriving platoon, and dynamic coordination, in which small groups of closely spaced signals communicate with one another to cycle synchronously with the group’s critical intersection. Simulation tests in VISSIM performed on arterial corridors in Massachusetts and Arizona show overall delay reductions of up to 14% compared to an optimized coordinated–actuated scheme where there is no transit priority, and more than 30% in scenarios with temporary oversaturation. Tests also show that with self-organizing control, transit signal priority can be more effective than with coordinated–actuated control, reducing transit delay by about 60%, or 12 to 14 s per intersection with little impact on traffic delay.     

Optimization of pedestrian phase patterns at signalized intersections: a multi‐objective approach

This paper presents a multi‐objective optimization model and its solution algorithm for optimization of pedestrian phase patterns, including the exclusive pedestrian phase (EPP) and the conventional two‐way crossing (TWC) at an intersection. The proposed model will determine the optimal pedestrian phase pattern and the corresponding signal timings at an intersection to best accommodate both vehicular traffic and pedestrian movements. The proposed model is unique with respect to the following three critical features: (1) proposing an unbiased performance index for comparison of EPP and TWC by explicitly modeling the pedestrian delay under the control of TWC and EPP; (2) developing a multi‐objective model to maximize the utilization of the available green time by vehicular traffic and pedestrian under both EPP or TWC; and (3) designing a genetic algorithm based heuristic algorithm to solve the model. Case study and sensitivity analysis results have shown the promising property of the proposed model to assist traffic practitioners, researchers, and authorities in properly selecting pedestrian phase patterns at signalized intersections. Copyright © 2013 John Wiley & Sons, Ltd.     

Modeling and simulation of vehicle projection arrival–discharge process in adaptive traffic signal controls

Real‐time signal control operates as a function of the vehicular arrival and discharge process to satisfy a pre‐specified operational performance. This process is often predicted based on loop detectors placed upstream of the signal. In our newly developed signal control for diamond interchanges, a microscopic model is proposed to estimate traffic flows at the stop‐line. The model considers the traffic dynamics of vehicular detection, arrivals, and departures, by taking into account varying speeds, length of queues, and signal control. As the signal control is optimized over a rolling horizon that is divided into intervals, the vehicular detection for and projection into the corresponding horizon intervals are also modeled. The signal control algorithm is based on dynamic programming and the optimization of signal policy is performed using a certain performance measure involving delays, queue lengths, and queue storage ratios. The arrival–discharge model is embedded in the optimization algorithm and both are programmed into AIMSUN, a microscopic stochastic simulation program. AIMSUN is then used to simulate the traffic flow and implement the optimal signal control by accessing internal data including detected traffic demand and vehicle speeds. Sensitivity analysis is conducted to study the effect of selecting different optimization criteria on the signal control performance. It is concluded that the queue length and queue storage ratio are the most appropriate performance measures in real‐time signal control of interchanges. Copyright © 2010 John Wiley & Sons, Ltd.     

Integrated fuzzy signal and ramp‐metering at a diamond interchange

We propose a fuzzy logic control for the integrated signal operation of a diamond interchange and its ramp meter, to improve traffic flows on surface streets and motorway. This fuzzy logic diamond interchange (FLDI) comprises of three modules: fuzzy phase timing (FPT) module that controls the green time extension of the current phase, phase logic selection (PLS) module that decides the next phase based on the pre‐defined phase sequence or phase logic and, fuzzy ramp‐metering (FRM) module that determines the cycle time of the ramp meter based on current traffic volumes and conditions of the surface streets and the motorways. The FLDI is implemented in Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Network Version 6 (AIMSUN 6), and compared with the traffic actuated signal control. Simulation results show that the FLDI outperforms the traffic‐actuated models with lower system total travel time, average delay, and improvements in downstream average speed and average delay. Copyright © 2011 John Wiley & Sons, Ltd.     

A real-time adaptive signal control in a connected vehicle environment

The state of the practice traffic signal control strategies mainly rely on infrastructure based vehicle detector data as the input for the control logic. The infrastructure based detectors are generally point detectors which cannot directly provide measurement of vehicle location and speed. With the advances in wireless communication technology, vehicles are able to communicate with each other and with the infrastructure in the emerging connected vehicle system. Data collected from connected vehicles provides a much more complete picture of the traffic states near an intersection and can be utilized for signal control. This paper presents a real-time adaptive signal phase allocation algorithm using connected vehicle data. The proposed algorithm optimizes the phase sequence and duration by solving a two-level optimization problem. Two objective functions are considered: minimization of total vehicle delay and minimization of queue length. Due to the low penetration rate of the connected vehicles, an algorithm that estimates the states of unequipped vehicle based on connected vehicle data is developed to construct a complete arrival table for the phase allocation algorithm. A real-world intersection is modeled in VISSIM to validate the algorithms. Results with a variety of connected vehicle market penetration rates and demand levels are compared to well-tuned fully actuated control. In general, the proposed control algorithm outperforms actuated control by reducing total delay by as much as 16.33% in a high penetration rate case and similar delay in a low penetration rate case. Different objective functions result in different behaviors of signal timing. The minimization of total vehicle delay usually generates lower total vehicle delay, while minimization of queue length serves all phases in a more balanced way.     

Integrated expression method for technical mapping of traffic parameters using RGB color model

In the field of traffic flow, speed, density, time, and distance are fundamental variables analyzed to predict traffic conditions. Reliable sources of information are gauged using tested mathematical approaches that have been developed. However, a fundamental diagram that could serve as a basis for expression techniques has not been devised. Red–green–blue (RGB) color modeling was used to overcome this limitation in traffic flow. The purpose of this study is to provide a way to understand traffic flow conditions based on features of three traffic flow elements simultaneously. The limitation of three‐dimensional expressions in two‐dimensional paper was extended to multi‐dimensional information. Information on speed, density, and flow were combined into a single RGB color and given the name RGB flow‐density space time‐distance space. This cancels out the effect of each individual's vehicular trajectories and contains five major components of a specific road section. The new gizmo aims to provide information on traffic flow conditions in transition and to stimulate further approaches related to the predictions and understanding of traffic flow. Copyright © 2016 John Wiley & Sons, Ltd.     

Nonlinear gating control for urban road traffic network using the network fundamental diagram

This work proposes a nonlinear model predictive controller for the urban gating problem. The system model is formalized based on a research on existing models of the network fundamental diagram and the perimeter control systems. For the existing models, modifications are suggested: additional state variables are allocated to describe the queue dynamics at the network gates. Using the extended model, a nonlinear model predictive controller is designed offering a ‘non‐greedy’ policy compared with previous, ‘greedy’ gating control designs. The greedy and non‐greedy nonlinear model predictive control (NMPC) controllers are compared with a greedy linear feedback proportional‐integral‐derivative (PID) controller in different traffic situations. The proposed non‐greedy NMPC controller outperforms the other two approaches in terms of travel distance performance and queue lengths. The performance results justify the consideration of queue lengths in dynamic modeling, and the use of NMPC approach for controller design. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of road width and traffic volume on vehicular interactions in heterogeneous traffic

Highway traffic flow phenomena involve several complex and stochastic variables with high interdependencies. The variations in roadway, traffic and environmental factors influence the traffic flow quality significantly. Capacity analysis of road sections under different traffic and geometric conditions need to quantify the vehicles of widely varying characteristics to a common and universally acceptable unit. Passenger car unit (PCU) is the universally adopted unit of traffic volume, keeping the passenger car as the ‘standard vehicle’ with reference to its static and dynamic characteristics; other vehicles are expressed to its equivalent number in terms of PCUs. The studies carried out in this aspect represent the dynamic nature of impedance caused by a vehicle while moving through a traffic stream. The PCU values recommended by the Highway Capacity Manual are widely applied in many countries; however, their applicability is highly under debate because of the variations in prevailing local traffic conditions. There are several factors that influence the PCU values such as traffic, roadway, vehicle, environmental and control conditions, etc. Apart from vehicular characteristics, the other two major factors that influence the PCU of vehicles are the following: (i) road width and (ii) traffic volume. In this study, estimation of PCU values for the different types of vehicles of a highly heterogeneous traffic on 7.5‐ and 11.0‐m‐wide roads, using micro‐simulation technique, has been dealt with. It has been found that the PCU value of a vehicle type varies significantly with variation in road width and traffic volume. The results of the study indicate that the PCU values are significantly influenced by the said two factors. Copyright © 2012 John Wiley & Sons, Ltd.     

Estimating time dependent O‐D trip tables during peak periods

Intelligent transportation systems (ITS) have been used to alleviate congestion problems arising due to demand during peak periods. The success of ITS strategies relies heavily on two factors: 1) the ability to accurately estimate the temporal and spatial distribution of travel demand on the transportation network during peak periods, and, 2) providing real‐time route guidance to users. This paper addresses the first factor. A model to estimate time dependent origin‐destination (O‐D) trip tables in urban areas during peak periods is proposed. The daily peak travel period is divided into several time slices to facilitate simulation and modeling. In urban areas, a majority of the trips during peak periods are work trips. For illustration purposes, only peak period work trips are considered in this paper. The proposed methodology is based on the arrival pattern of trips at a traffic analysis zone (TAZ) and the distribution of their travel times. The travel time matrix for the peak period, the O‐D trip table for the peak period, and the number of trips expected to arrive at each TAZ at different work start times are inputs to the model. The model outputs are O‐D trip tables for each time slice in the peak period. 1995 data for the Las Vegas metropolitan area are considered for testing and validating the model, and its application. The model is reasonably robust, but some lack of precision was observed. This is due to two possible reasons: 1) rounding‐off, and, 2) low ratio of total number of trips to total number of O‐D pair combinations. Hence, an attempt is made to study the effect of increasing this ratio on error estimates. The ratio is increased by multiplying each O‐D pair trip element with a scaling factor. Better estimates were obtained. Computational issues involved with the simulation and modeling process are discussed.     

Optimization method of alternate traffic restriction scheme based on elastic demand and mode choice behavior

As a countermeasure to urban traffic congestion, alternate traffic restriction (ATR) involves a certain proportion of automobiles being prohibited from entering pre-determined ATR districts during specific time periods. The present study introduces an optimization method for ATR schemes in terms of both their restriction districts and the proportion of restricted automobiles. As a Stackelberg game between traffic policy makers and road users, the ATR scheme optimization problem is established using a bi-level programming model, with the upper-level examining an ATR scheme aimed at consumers’ surplus maximization under the condition of overload flow minimization, and the lower-level synthetically optimizing elastic demand, mode choice (private car, public transit and park-and-ride) and multi-class user equilibrium assignment. A genetic algorithm based on the graph theory is also proposed to solve the bi-level programming model with a gradient project algorithm for solving the lower-level model. To our knowledge, this study represents the first attempt to theoretically optimize an ATR scheme using a systematic approach with mathematical model specification.     

An integrated real-time traffic signal system for transit signal priority,incident detection and congestion management

This paper presents a traffic control system that can work standalone to handle various boundary conditions of the recurrent, non-recurrent congestion, transit signal priority and downstream blockage conditions to improve the overall traffic network vehicular productivity and efficiency. The control system uses field detectors’ data to determine the boundary conditions of all incoming and exit links. The developed system is interfaced with CORSIM micro-simulation for rigorous evaluations with different types of signal phase settings. The comparative performance of this control logic is quite satisfactory for some of the most frequently used phase settings in the network with a high number of junctions under highly congested conditions.     

Estimating freeway route travel time distributions with consideration to time‐of‐day,inclement weather,and traffic incidents

This paper develops an efficient probabilistic model for estimating route travel time variability, incorporating factors of time‐of‐day, inclement weather, and traffic incidents. Estimating the route travel time distribution from historical link travel time data is challenging owing to the interactions among upstream and downstream links. Upon creating conditional probability function for each link travel time, we applied Monte Carlo simulation to estimate the total travel time from origin to destination. A numerical example of three alternative routes in the City of Buffalo shows several implications. The study found that weather conditions, except for snow, incur minor impact on off‐peak and weekend travel time, whereas peak travel times suffer great variations under different weather conditions. On top of that, inclement weather exacerbates route travel time reliability, even when mean travel time increases moderately. The computation time of the proposed model is linearly correlated to the number of links in a route. Therefore, this model can be used to obtain all the origin to destination travel time distributions in an urban region. Further, this study also validates the well‐known near‐linear relation between the standard deviation of travel time per unit distance and the corresponding mean value under different weather conditions. Copyright © 2016 John Wiley & Sons, Ltd.     

Visco‐elastic traffic flow model

To increase our understanding of the operations of traffic system, a visco‐elastic traffic model was proposed in analogy of non‐Newtonian fluid mechanics. The traffic model is based on mass and momentum conservations, and includes a constitutive relation similar to that of linear visco‐elastic fluids. The further inclusion of the elastic effect allows us to describe a high‐order traffic model more comprehensively because the use of relaxation time indicates that vehicle drivers adjust their time headway in a reasonable and safe range. The self‐organizing behaviour is described by introducing the effects of pressure and visco‐elasticity from the point of view in fluid mechanics. Both the viscosity and elasticity can be determined by using the relaxation time and the traffic sound speed. The sound speed can be approximately represented by the road operational parameters including the free‐flow speed, the jam density, and the density of saturation if the jam pressure in traffic flows is identical to the total pressure at the flow saturation point. A linear stability analysis showed that the traffic flow should be absolutely unstable for disturbances with short spatial wavelengths. There are two critical points of regime transition in traffic flows. The first point happens at the density of saturation, and the second point occurs at a density relating on the sound speed and the fundamental diagram of traffic flows. By using a triangular form flow–density relation, a numerical test based on the new model is carried out for congested traffic flows on a loop road without ramp effect. The numerical results are discussed and compared with the result of theoretical analysis and observation data of traffic flows. Copyright © 2011 John Wiley & Sons, Ltd.     

Field implementation feasibility study of cumulative travel‐time responsive (CTR) traffic signal control algorithm

The cumulative travel‐time responsive (CTR) algorithm determines optimal green split for the next time interval by identifying the maximum cumulative travel time (CTT) estimated under the connected vehicle environment. This paper enhanced the CTR algorithm and evaluated its performance to verify a feasibility of field implementation in a near future. Standard Kalman filter (SKF) and adaptive Kalman filter (AKF) were applied to estimate CTT for each phase in the CTR algorithm. In addition, traffic demand, market penetration rate (MPR), and data availability were considered to evaluate the CTR algorithm's performance. An intersection in the Northern Virginia connected vehicle test bed is selected for a case study and evaluated within vissim and hardware in the loop simulations. As expected, the CTR algorithm's performance depends on MPR because the information collected from connected vehicle is a key enabling factor of the CTR algorithm. However, this paper found that the MPR requirement of the CTR algorithm could be addressed (i) when the data are collected from both connected vehicle and the infrastructure sensors and (ii) when the AKF is adopted. The minimum required MPRs to outperform the actuated traffic signal control were empirically found for each prediction technique (i.e., 30% for the SKF and 20% for the AKF) and data availability. Even without the infrastructure sensors, the CTR algorithm could be implemented at an intersection with high traffic demand and 50–60% MPR. The findings of this study are expected to contribute to the field implementation of the CTR algorithm to improve the traffic network performance. Copyright © 2017 John Wiley & Sons, Ltd.     

Analysis of peak and non‐peak traffic forecasts using combined models

Accurate and timely traffic forecasting is crucial to effective management of intelligent transportation systems (ITS). To predict travel time index (TTI) data, we select six baseline individual predictors as basic combination components. Applying the one‐step‐ahead out‐of‐sample forecasts, the paper proposes several linear combined forecasting techniques. States of traffic situations are classified into peak and non‐peak periods. Based on detailed data analyses, some practical guidance and comments are given in what situation a combined model is better than an individual model or other types of combined models. Indicating which model is more appropriate in each state, persuasive comparisons demonstrate that the combined procedures can significantly reduce forecast error rates. It reveals that the approaches are practically promising in the field. To the best of our knowledge, it is the first time to systematically investigate these approaches in peak and non‐peak traffic forecasts. The studies can provide a reference for optimal forecasting model selection in each period. Copyright © 2010 John Wiley & Sons, Ltd.