Influence of pilot injection on combustion characteristics and emissions in a DI diesel engine fueled with diesel and DME

This work experimentally investigates how the dwell time between pilot injection and main injection influences combustion and emissions characteristics (NOx, CO, THC and smoke) in a single-cylinder DI diesel engine. The experiments were conducted using two fuel injection systems according to the fuel type, diesel or dimethyl ether (DME), due to the different fuel characteristics. The injection strategy is accomplished by varying the dwell time (10°CA, 16°CA and 22°CA) between injections at five main injection timings (?4°CA aTDC, ?2°CA aTDC, 0°CA aTDC, 2°CA aTDC and 4°CA aTDC). Results from pilot-main injection conditions are compared with those shown in single injection conditions to better demonstrate the potential of pilot injection. It was found that pilot injection is highly effective for lowering heat-release rates with smooth pressure traces regardless of the fuel type. Pilot injection also offers high potential to maintain or increase the BMEP; even the combustion-timing is retarded to suppress the NOx emission formation. Overall, NOx emission formation was suppressed more by the combustion phasing retard effect, and not the pilot injection effect considered in this study. Comparison of the emissions for different fuel types shows that CO and HC emissions have low values below 100 ppm for DME operation in both single injection and pilot-main injection. However, NOx emission is slightly higher in the earlier main injection timings (?4°CA aTDC, ?2°CA aTDC) than diesel injections. Pilot injection was found to be more effective with DME for reducing the amount of NOx emission with combustion retardation, which indicates a level of NOx emission similar to that of diesel. Although the diesel pilot-main injection conditions show higher smoke emission than single-injection condition, DME has little smoke emission regardless of injection strategy.     

柴油机燃烧放热模式分析

研究了NOx和PM的机内净化方法,试验分析了EGR、高压喷射对柴油机排放的影响规律。在此基础上确定低NOx和低PM两种理想燃烧模式对应放热率参数的阈值。结果表明:NOx净化达到欧Ⅳ标准时,所对应的归一化放热率阈值为0.045~0.049°CA-1;PM净化达到欧Ⅳ标准时,对应的归一化放热率阈值为0.045~0.06°CA-1;二者同时达欧Ⅳ的归一化放热率阈值为二者的交集0.045~0.049°CA-1。     

Enhancement of NOx-PM trade-off in a diesel engine adopting bio-ethanol and EGR

For realizing a premixed charge compression ignition (PCCI) engine, the effects of bio-ethanol blend oil and exhaust gas recirculation (EGR) on PM-NOx trade-off have been investigated in a single cylinder direct injection diesel engine with the compression ratio of 17.8. In the present experiment, the ethanol blend ratio and the EGR ratio were varied focusing on ignition delay, premixed combustion, diffusive combustion, smoke, NOx and the thermal efficiency. Very low levels of 1.5 [g/kWh] NOx and 0.02 [g/kWh] PM, which is close to the 2009 emission standards imposed on heavy duty diesel engines in Japan, were achieved without deterioration of the thermal efficiency in the PCCI engine operated with the 50% ethanol blend fuel and the EGR ratio of 0.2. It is found that this improvement can be achieved by formation of the premixed charge condition resulting from a longer ignition delay. A marked increase in ignition delay is due to blending ethanol with low cetane number and large latent heat, and due to lowering in-cylinder gas temperature on compression stroke based on the EGR. It is noticed that smoke can be reduced even by increasing the EGR ratio under a highly premixed condition.     

Combustion and emission characteristics of a lean burn natural gas engine

Lean burn is an effective way to improve spark ignition engine fuel economy. In this paper, the combustion and emission characteristics of a lean burn natural gas fuelled spark ignition engine were investigated at various throttle positions, fuel injection timings, spark timings and air fuel ratios. The results show that ignition timings, the combustion duration, the coefficient of variation (COV) of the indicated mean effective pressure (IMEP) and engine-out emissions are dependent on the overall air fuel ratio, spark timings, throttle positions and fuel injection timings. With the increase of the air fuel ratio, the ignition delays and combustion duration increases. Fuel injection timings affect ignition timings, combustion duration, IMEP, and the COV of the IMEP. Late fuel injection timings can decrease the COV of the IMEP. Moreover, the change in the fuel injection timings reduces the engine-out CO, total hydrocarbon (THC) emissions. Lean burn can significantly reduce NOx emissions, but it results in high cyclic variations.     

Effect of operating parameters on diesel/propane dual fuel premixed compression ignition in a diesel engine

In this research, the effects of three operating parameters (Diesel injection timing, propane ratio, and exhaust gas recirculation (EGR) rates) in a diesel-propane dual fuel combustion were investigated. The characteristics of dual-fuel combustion were analyzed by engine parameters, such as emission levels (Nitrogen oxides (NO_x) and particulate matter (PM)), gross indicated thermal efficiency (GIE) and gross IMEP Coefficient of Variance (CoV). Based on the results, improving operating strategies of the four main operating points were conducted for dual-fuel PCCI combustion with restrictions on the emissions and the maximum pressure rise rate. The NOx emission was restricted to below 0.21 g/kWh in terms of the indicated specific NO_x (ISNO_x), PM was restricted to under 0.2 FSN, and the maximum pressure rise rate (MPRR) was restricted to 10 bar/deg. Dual-fuel PCI combustion can be available with low NO_x, PM emission and the maximum pressure rise rate in relatively low load condition. However, exceeding of PM and MPRR regulation was occurred in high load condition, therefore, design of optimal piston shape for early diesel injection and modification of hardware optimizing for dual-fuel combustion should be taken into consideration.     

Effects of the fuel injection ratio on the emission and combustion performances of the partially premixed charge compression ignition combustion engine applied with the split injection method

Currently, due to the severity of world-wide air pollution by substances emitted from vehicles, emission control is being enforced more strictly, and it is expected that the regulation requirements for emission will become even more severe. A new concept combustion technology that can reduce the Nitrogen oxides (NOx) and PM in relation to combustion is urgently required. As a core combustion technology among new combustion technologies for the next generation engine, the homogenous charge compression ignition (HCCI) is expanding its application range by adopting a multiple combustion mode, a catalyst, direct fuel injection and partially premixed charge compression ignition combustion using the split injection method. This paper used a split injection method in order to apply the partially premixed charge compression ignition combustion method without significantly altering engine specifications of the multiple combustion mode and practicality by referring to the results of studies on the HCCI engine. Furthermore, the effects of the ratio of the fuel injection amount on split injection are investigated. From the test results, the adequate combination of the ratio of the fuel injection amount for the split injection method has some benefit on exhaust and fuel economy performance in a naturally aspirated single cylinder diesel engine.     

基于喷射正时的柴油机燃烧和排放研究

基于集成电控单体泵柴油机,讨论了喷射正时对柴油机燃烧及排放特性的影响规律。喷射正时对滞燃期和速燃期有显著的影响,从而影响放热规律、缸内压力和燃烧温度,进而对NOx和PM排放特性有显著的影响。在中大负荷下,随着喷射正时的滞后,放热率曲线相对于上止点的相位滞后,缸内最高燃烧温度下降,NOx排放下降,PM排放升高。在中小负荷下,随着喷射正时的进一步滞后,NOx和PM的排放同时下降。     

多次喷射对柴油机燃烧与排放影响的试验研究

基于1台高压共轨涡轮增压柴油机,采用不同的预喷正时、预喷油量与后喷正时等,研究了多次喷射对燃烧放热、排放生成与燃油经济性的影响,以实现均质压燃和低温燃烧过程。研究结果表明:随预喷正时提前,缸内峰值压力降低,主燃阶段的滞燃期缩短,NOx和炭烟排放均降低;随预喷油量增加,预喷阶段燃烧的放热率和最大压力升高率增大,NOx和HC排放增大,而PM和CO排放降低;随后喷始点推迟,缸内压力与主放热率峰值差异变小,NOx排放降低,但炭烟排放先增大后逐渐降低。     

Combined effect of boost pressure and injection timing on the performance and combustion of CNG in a DI spark ignition engine

There is an increasing interest in supercharging spark ignition engines operating on CNG (compressed natural gas) mainly due to its superior knock resisting properties. However, there is a penalty in volumetric efficiency when directly injecting the gaseous fuel at early and partial injection timings. The present work reports the combined effects of a small boost pressure and injection timing on performance and combustion of CNG fueled DI (direct injection) engine. The experimental tests were carried out on a 4-stroke DI spark ignition engine with a compression ratio of 14. Early injection timing, when inlet valves are still open (at 300°BTDC), and partial injection timing, in which part of the injection occurs after the inlet valves are closed (at 180°BTDC), were varied at each operating speed with variation of the boost pressure from 2.5 to 10 kPa. A narrow angle injector (NAI) was used to increase the mixing rate at engine speeds between 2000 and 5000 rpm. Similar experiments were conducted on a naturally aspirated engine and the results were then compared with that of the boosting system to examine the combined effects of boost pressure and injection timing. It was observed that boost pressure above 7.5 kPa resulted in an improvement of performance and combustion of CNG DI engine at all operating speeds. This was manifested in the faster heat release rates and mass fraction burned that in turn improved combustion efficiency of the boosting system. An increased in cylinder pressure and temperature was also observed with boost pressure compared to naturally aspirated engine. Moreover, the combustion duration was reduced due to concentration of the heat release near to the top dead center as the result of the boost pressure. Supercharging was also found to reduce the penalty of volumetric efficiency at both the simulated port and partial injection timings.     

降低汽车发动机排放的技术

从机内净化技术，机外净化技术和应用清洁燃料等方面讨论了降低汽车发动机排放技术，对车用发动机分层充气预混合稀薄燃料（MPFI）、汽油机直喷燃烧（GDI）和均质混合压缩点火式燃烧（HCCI）等燃烧技术，选择催化还原剂（SCR）、NOx存储器还原催化系统（NSR）、等离子体辅助催化剂等新的稀燃NOx催化剂和微粒处理系统，通过这些技术的综合运用达到不断严格的排放标准和环保要求。     

废气再循环对车用柴油机性能与排放的影响

为了降低车用柴油机的NOx排放，研究了不同工况下EGR率对柴油机性能的影响。试验结果表明，采用EGR可以有效地降低NOx排放。大负荷比小负荷效果显著，但微粒的排放有所增加。小负荷采用EGR时可以改善发动机的燃烧，微粒排放基本没有变化。空燃比是影响微粒排放的关键因素，小负荷宜采用大EGR率，大负荷时宜采用小EGR率，以求在控制NOx排放降低的同时，总的微粒排放不至增加过多。     

Operating strategy for gasoline/diesel dual-fuel premixed compression ignition in a light-duty diesel engine

Environmental problems have become a major issue for diesel engine development. Although emission aftertreatment systems such as DPFs (diesel particulate filters), LNTs (lean NOx traps) and SCR (selective catalytic reduction) have been used in diesel vehicles, the manufacturing cost increase caused by this equipment can be hard to be control. Thus, it is better for engine emissions to be reduced by improving the combustion system. A dual-fuel combustion concept is a recommended method to improve a combustion system and effectively reduce emissions. Low reactivity fuel including gasoline and natural gas, which was supplied to the intake port by the FPI (port fuel injector), improved the premixed air-fuel mixture conditions before ignition. Additionally, a small amount of high reactivity fuel, in this case diesel, was injected into the cylinder directly as an ignition source. This dual-fuel combustion promises lower levels of NOx (nitrogen oxide) and PM (particulate matter) emissions due to the elimination of local rich regions in the cylinder. However, it is challenging to control the dual-fuel combustion because the combustion stability and efficiency deteriorate due to the lack of ignition source and reactivity. Thus, it is important to establish an appropriate dual-fuel operating strategy to achieve stable, high efficiency and low emission operation. As a result of this research, a detailed operating method of dual-fuel PCI (premixed compression ignition) was introduced in detail at a low speed and low load condition by using a single cylinder diesel engine. Engine operating parameters including the gasoline ratio, a diesel injection strategy consisting of multiple injectors and timing, the EGR (exhaust gas recirculation) rate and the intake pressure were controlled to satisfy the low ISNOx (indicated specific NOx) and PM emissions levels (0.21 g/kWh and 0.1 FSN, 0.040 g/kWh, respectively) as per the EURO-6 regulation without any after-treatment systems. The results emphasized that a well-constructed dual-fuel PCI operating strategy showed low NOx and PM emissions and high GIE (gross indicated fuel conversion efficiency) with excellent combustion stability.     

基于改善柴油机排放的燃烧过程优化措施

改善柴油机排放的核心是对燃烧过程进行优化,通过改善燃烧过程来降低柴油机排放是当前柴油机研究中的重要课题。本文主要从优化进气系统、优化喷油系统、优化燃烧室结构、燃料的改质及优化润滑系统五个方面进行分析,综合这些相互制约的优化措施优化柴油机的燃烧过程,降低颗粒物质PM和NOx的直接排放。     

EGR对DME发动机性能和排放的影响

开展了4100QBZL增压中冷发动机燃用D40二甲醚—柴油混合燃料时采用EGR技术对发动机动力性、经济性、燃烧和排放性能影响的试验研究。试验结果表明:EGR技术可以有效降低D40混合燃料发动机的NOx排放,EGR率越高,NOx排放改善越明显,但会不同程度恶化烟度、HC,CO等排放。     

Major sources of hydrocarbon emissions in a premixed charge compression ignition engine

Although premixed charge compression ignition (PCCI) combustion engines are praised for potentially high efficiency and clean exhaust, experimental engines built to date emit more hydrocarbons (HCs) and carbon monoxide (CO) than the conventional machines. These compounds are not only strictly controlled components of the exhaust gas of road vehicles but are also an energy loss indicator. The prime objective of this study was to investigate the major sources of the HCs formed in the combustion chamber of an experimental PCCI engine in order to suggest some effective technologies for HC reduction. In this study, to explore the dominant sources of HC emissions in both operation modes, a single cylinder engine was prepared such that it could operate using either conventional diesel combustion or PCCI combustion. Specifically, the contributions of the top-ring crevice volume in the combustion chamber and the bulk quenching of the lean mixture were investigated. To understand the influence of the shape and magnitude of the crevice on HC emissions, the engine was operated with 12 specially prepared pistons with different top-ring crevices installed one after another. The engine emitted proportionally more HCs as the depth of the crevice increased as long as the width remained narrower than the prevailing quench distance. The top-ring-crevice-originated exhaust HCs comprised approximately 31% of the total HC emissions in the baseline condition. In a series of tests to estimate the effects of bulk quench on exhaust HC emissions, intake air was heated from 300K to 400K in steps of 25K. With the intake air heated, HC and CO emissions decreased with a gradually diminishing rate to zero at 375K. In conclusion, the most dominant sources of HC emissions in PCCI engines were the crevice volumes in the combustion chamber and the bulk quenching of the lean mixtures. The key methods for reducing HC emissions in PCCI engines are minimizing crevice volume in the combustion chamber and maximizing intake air temperature allowed based on the permissible NOx level.     

Effects of intake valve angle on combustion characteristic in an SI engine

In this study, 2 different valve-angle engines, one is wide and the other is narrow, were prepared for investigating the effects of the angle on the combustion. For this purpose, the part load performances were evaluated and the pressures were measured for combustion analysis at an engine bench under 5 different operating conditions, varying the compression ratio. The results show that the combustion proceeds so faster in the small IVA engine that its MBT timings are retarded considerably compared with that of large one and result in lower NOx emission level; however, unburned HC is higher because of its geometrical feature. In addition, there is no substantial difference between 2 IVA engines in the timings of combustion initiation and completion as a crank-angle-position-base in spite of the considerable difference of spark timing, on the other hands, the ignition delay of the small IVA is shorter than that of large one. Also the phenomena that the flame propagation is faster and the instant heat release rate is more concentrated and higher in the small were observed. Also, the burn duration of small one is shorter and the combustion process is more accelerated up to the mid-combustion stage; however, the process of large one is faster as the combustion approaches the last stage and the differences of combustion duration reduce as the compression ratio increases. Finally, the engine runs more stable when the IVA is small without any exception because of its rapid burn at the initial combustion stage.     

Exhaust emissions and its control methods in compression ignition engines: A review

Extensive usage of automobiles has certain disadvantages and one of them is its negative effect on environment. Carbon dioxide (CO₂), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NO_x), sulphur dioxide (SO₂) and particulate matter (PM) come out as harmful products during incomplete combustion from internal combustion (IC) engines. As these substances affect human health, regulatory bodies impose increasingly stringent restrictions on the level of emissions coming out from IC engines. This trend suggests the urgent need for the investigation of all aspects relevant to emissions. It is required to modify existing engine technologies and to develop a better after-treatment system to achieve the upcoming emission norms. Diesel engines are generally preferred over gasoline engines due to their undisputed benefit of fuel economy and higher torque output. However, diesel engines produce higher emissions, particularly NO_x and PM. Aftertreatment systems are costly and occupy more space, hence, in-cylinder solutions are preferred in reducing emissions. Exhaust gas recirculation (EGR) technology has been utilized previously to reduce NO_x. Though it is quite successful for small engines, problem persists with large bore engines and with high rate of EGR. EGR helps in reducing NO_x, but increases particulate emissions and fuel consumption. Many in-cylinder solutions such as lower compression ratios, modified injection characteristics, improved air intake system etc. are required along with EGR to accomplish the future emission norms. Modern combustion techniques such as low temperature combustion (LTC), homogeneous charge compression ignition (HCCI), premixed charge compression ignition (PCCI) etc. would be helpful for reducing the exhaust emissions and improving the engine performance. However, controlling of autoignition timing and achieving wider operating range are the major challenges with these techniques. A comprehensive review of diesel engine performance and emission characteristics is given in this paper.     

Improvement of combustion efficiency and emission characteristics of IC diesel engine operating on ESC cycle applying Variable Geometry Turbocharger (VGT) with vaneless turbine volute

Based on experimental data, the present study investigates the influence of turbine adjustment in a turbocharger with vaneless turbine volute on diesel combustion efficiency indices and emission characteristics. Experimental investigations were conducted on engine modes as set out by the European Stationary Cycle (ESC). The adjustment algorithms selected for the experiment under ESC modes included adjustment to achieve minimal values of specific fuel consumption (SFC), NOx, CO and particulate matter (PM). In present research only VGT adjustment was investigated, the factors like fuel injection timing and EGR were not investigated. As a result we were able to make a comparison of the engine combustion efficiency and emission indices for VGT and a common turbocharger running on ESC cycle modes.     

柴油机应用非标柴油一二甲醚混合燃料的性能研究

对非标柴油—二甲醚混合燃料在柴油机上的应用进行研究.结果表明:燃用D50混合燃料柴油机动力性略有下降,但是排放性能大为改善,尤其是烟度;调整供油提前角对D50柴油机的动力性影响不大,供油提前角14°曲轴转角时柴油机的排放性能最佳;采用EGR技术可有效地降低NOx排放,但是在大负荷下加大废气引入量将会导致燃烧恶化,炭烟排...     

Predicting auto-ignition characteristics of RCCI combustion using a multi-zone model

The objective of new combustion concepts is to meet emission standards by improving fuel air mixing prior to ignition. Since there is no overlap between injection and ignition, combustion is governed mainly by chemical kinetics and it is challenging to control the phasing of ignition. Reactivity Controlled Compression Ignition (RCCI) combustion aims to control combustion phasing by altering the fuel ratios of the high- and low octane fuel and injection timings. In this study the dual fuel blend is prepared with gasoline and diesel fuels. The applied injection timings of the diesel are very early (90 to 60° CA bTDC). In the detailed reaction mechanism, n-heptane and iso-octane represent diesel and gasoline fuel, respectively. A multi-zone model approach is implemented to perform RCCI combustion simulation. Ignition characteristics are analyzed by using CA50 as the main parameter. In the experiments for the early direct injection (DI) timing advancing the injection time results in a later ignition. Qualitatively, the trend effect of the diesel injection timing and the effect of the ratio gasoline/diesel are captured accurately by the multi-zone model.