考虑点腐蚀影响的海洋钢结构剩余极限强度研究进展

为得到考虑点腐蚀影响的海洋钢结构剩余强度研究领域的发展趋势,本文对国内外该领域公开发表的文章进行综述,根据本文的研究可以发现:由于海洋钢结构的大尺度和复杂性,数值模拟已成为受蚀船体结构剩余强度的主要研究方法,但模拟结构的有效性仍需进一步检验;对于点腐蚀,就研究参数而言,长细比、DOP、体积损失是学者们最为关注的指标,但对点蚀板强度缺少时变可靠性研究;计算模型中都缺乏对焊接残余应力的考虑。本文所做的研究可为该领域下一步研究方向提供参考。     

考虑点腐蚀影响的海洋钢结构剩余极限强度研究进展

为得到考虑点腐蚀影响的海洋钢结构剩余强度研究领域的发展趋势,本文对国内外该领域公开发表的文章进行综述,根据本文的研究可以发现:由于海洋钢结构的大尺度和复杂性,数值模拟已成为受蚀船体结构剩余强度的主要研究方法,但模拟结构的有效性仍需进一步检验;对于点腐蚀,就研究参数而言,长细比、DOP、体积损失是学者们最为关注的指标,但对点蚀板强度缺少时变可靠性研究;计算模型中都缺乏对焊接残余应力的考虑.本文所做的研究可为该领域下一步研究方向提供参考.     

破损船体剩余极限强度的影响参数与敏感度分析

在对破损船体剩余极限强度的影响参数进行分析的基础上,提出了一个对破损船体剩余极限强度影响大小的衡量指标-敏感度.根据这一衡量指标,逐一分析不同破损状态对破损船体剩余极限强度的影响程度.针对不同的船型,对破损船体剩余极限强度的影响参数进行了分析及计算,并给出了一条实船的计算结果,最后得出了一些有应用价值和指导意义的结论.     

Numerical investigation on the ultimate strength of stiffened cylindrical shells considering residual stresses and shakedown

In this paper, the effects of residual stresses on the ultimate strength of stiffened cylinders are numerically investigated with an emphasis on shakedown which might occur during the service of these structures. Residual stresses caused by two types of actions, namely, cold bending and welding, are simulated with simplified approaches in numerical analysis. Cold bending stresses are simulated by simulating cold rolling and elastic springback until the desired curvature for cylindrical shell is obtained. Welding is simulated by applying cooling down to a certain temperature on the elements adjacent to stiffener-shell joints to obtain weld-shrinkage with realistic magnitudes. Six small-scale externally pressurized ring-stiffened cylinder models are utilized to evaluate the appropriateness of the method for inclusion of welding residual stresses in numerical analysis by comparing the experimental and numerical results. Ultimate strength analyses are then performed for a reference ring-stiffened cylinder model under radial pressure and stringer-stiffened cylinder under axial loading. To assess the effect of shakedown, after applying cyclic compressive loading to the ring-stiffened cylinder model, the level of stress relief and the change in the ultimate strength are evaluated.     

某双壳油船总纵极限强度计算与分析

随着船体破坏机理的研究进一步深入,在进行船体结构设计时除了目前大多数船级社规范中采用的线弹理论计算方法,另一个重要指标——船体总纵极限强度也必须考虑。以某双壳油船为例,采用不同计算方法对该船中剖面总纵极限弯矩进行计算分析。结果表明:该双壳油船的总纵极限强度满足共同规范的相关要求。     

基于船体极限强度和碰撞剩余强度的HCSR对比分析

2013版HCSR对极限强度和船体梁载荷计算的诸多安全系数和公式做出了新的修正。第五章船体梁强度新增加针对船体梁剩余强度的计算和校核。本文基于Smith法,根据2013版HCSR中船体梁载荷计算公式和极限强度计算流程的规定,考虑材料屈服、结构单元屈曲及后屈曲的特性,应用Fortran程序设计语言编写船体极限强度计算程序,以某76 000 t散货船为例,对完整船体的极限强度进行计算,对碰撞状态下破损船体的剩余强度进行计算并校核承载能力。通过对比ABS和DNV规范中的碰撞模型,2013版HCSR指定的剩余强度校核公式及船体梁载荷计算公式中选取的校核公式更严格。     

基于完整船体极限强度和搁浅剩余强度的协调共同结构规范对比分析

文章基于Smith法,根据国际船级社协会发布的2013版协调共同结构规范(HCSR)中破损模型、失效模式和载荷模型,考虑材料屈服、结构单元屈曲及后屈曲的特性,应用FORTRAN程序设计语言编写船体极限强度计算程序,以某76000吨散货船为算例,对完整船体的极限强度进行计算,对搁浅状态下破损船体的剩余强度进行计算并校核承载能力。通过在中拱和中垂工况下与其他规范的对比验证,2013版HCSR指定的剩余强度校核公式及船体梁载荷计算公式中选取的安全系数要求更高,校核更严格。     

含初始变形船体加筋板有效宽度及剩余极限强度研究

为了评估舰船结构损伤后的剩余强度,对船体加筋板出现初始几何变形后,参与总纵强度的有效宽度和加筋板剩余极限强度进行研究。将加筋板受到垂直于平面压力后的变形,作为其初始几何变形,改变变形的方向和大小,利用有限元软件Ansys对加筋板结构进行线性和非线性分析。定义了板有效宽度计算方法,对不同变形方向和变形幅值时板的有效宽度和加筋板的极限强度进行对比分析,并拟合得到了计算板有效宽度和加筋板极限强度的经验公式。结果表明,初始几何变形会削弱加筋板结构的强度。在对损伤后船体结构强度进行分析和校核时,提出的经验公式可以直接用来计算板的有效宽度和加筋板的极限强度。     

Elastic local buckling strength of stiffened plate considering plate/stiffener interaction and welding residual stress

An analytical formula for estimating elastic local buckling strength of a continuous stiffened plate subjected to biaxial thrust is derived considering the influence of plate/stiffener interaction and welding residual stresses. Through a comparison of calculated results with those by FEM eigenvalue analysis, high accuracy of the proposed formula is demonstrated. A series of buckling strength analyses is performed on the deck and bottom plating of actual ships. It has been found that:

Full-size image

Experimental and numerical investigations of the ultimate torsional strength of an ultra large container ship

Structures of ultra large container ships (ULCS) are characterized by large deck openings and low torsional rigidity. It is essential to comprehensively figure out their collapse behaviors under pure torsion with both model experiments and numerical simulations, making an evaluation of their ultimate torsional strength. In this paper, a similar scale model of a 10,000TEU container ship has been designed and manufactured first, in which both geometric similarity and strength similarity are taken into account. Next the collapse behaviors of the test model are detailedly illustrated with both experimentally and numerically obtained results. Then discussions on warping or shear buckling deformations involved in the collapse process of the structure are conducted with extended numerical simulations. Finally, the ultimate torsional strength of the true ship is evaluated according to the similarity theory. Results show that it is the yielding and shear buckling of the side shells that causes the failure of the hull girder under pure torsion. Further nonlinear finite element analysis demonstrates that it may either have warping or shear buckling deformations in the torsional collapse process of the hull girder with a large deck opening, depending on the local rigidity distribution of side shells, which has a significant effect on the ultimate torsional strength of the hull girder.     

A general scaled model design method of stiffened plate subjected to combined longitudinal compression and lateral pressure considering the ultimate strength and collapse modes

A general and efficient scaled method for stiffened plates subjected to combined longitudinal compression and lateral pressure is proposed based on slenderness, simply by adjusting the number of stiffeners. The design method makes it easier to determine the dimensions of the scaled model for a given scale ratio compared with the previously proposed method. The emphasis is on the influence of the plate slenderness, the column slenderness, and the non-dimensional parameter of the lateral pressure on the ultimate strength. By maintaining the consistency of the plate slenderness and column slenderness, the proposed method is applicable for designing scaled models with materials of different yield stresses and Young's moduli. A similar effect of the lateral pressure on the ultimate strength of the prototype and scaled models is achieved by maintaining the non-dimensional parameter. In addition, the applicability of the scaled method to the initial deflection is considered, which provides a reference for similar models. The similitude of the scaled method is verified for several typical buckling modes, including the beam–column, tripping, web and overall collapse modes. Given the numerical results, the proposed general and fast scaled method can provide reasonable dimensions of scaled stiffened plates subjected to combined loads.