Catalytic Combustion of Lean Methane Assisted by Electric Field over Pd/Co<Subscript>3</Subscript>O<Subscript>4</Subscript> Catalysts at Low Temperature

A series of Pd/Co₃O₄ catalysts were prepared by Self-Propagating High-Temperature Synthesis (SHS) method in this study, and electric field was applied for catalytic combustion of lean methane over Pd/Co₃O₄ catalysts at low temperature. When electric field was applied, the catalytic combustion performance of Pd/Co₃O₄ catalysts was greatly improved, and the application of electric field could reduce the load of active element Pd to some extent while maintaining the same efficiency. Based on experimental tests and the analysis results of X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), H₂-temperature-programmed reduction (H₂-TPR) and in-situ diffuse reflectance infrared Fourier transform spectroscopy (in-situ DRIFTS), the mechanism of catalytic oxidation of CH₄ over Pd/Co₃O₄ catalysts in electric field was proposed. The catalytic combustion of CH₄ occurs only when the temperature is higher than 250 °C normally, but when electric field was applied, the whole process of CH₄ oxidation was promoted significantly and the reaction temperature was reduced. Electric field could promote the reduction of the support Co₃O₄ to release the lattice oxygen, resulting in the increase of PdO_x and the surface chemisorbed oxygen, which could provide more active sites for the low-temperature oxidation of CH₄. Furthermore, electric field could accelerate the dehydroxylation of CoOOH to further enhance the activity of the catalysts.     

Study on Oxidation Activity of CuCeZrO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Doped with K for Diesel Engine Particles in NO/O<Subscript>2</Subscript>

CuCeZrO_x and KCuCeZrO_x catalysts were synthesized and coated on the blank diesel particulate filter (DPF) substrate and a particulate matter (PM) loading apparatus was used for soot loading. The catalytic performances of soot oxidation were evaluated by temperature programmed combustion (TPC) test and characterization tests were conducted to investigate the physicochemical properties of the catalysts. The reaction mechanism in the oxidation process was analyzed with diffuse reflectance infrared Fourier transform spectroscopy. The results demonstrated that CuCeZrO_x catalyst exhibited high activities of soot oxidation at low temperature and the best results have been attained with Cu_0.9Ce_0.05Zr_0.05O_x over which the maximum soot oxidation rate decreased to 410 °C. Characterization tests have shown that catalysts containing 90% Cu have uniformly distributed grains and small particle sizes, which provide excellent oxidation activity by providing more active sites and forming a good bond between the catalyst and the soot. The low-temperature oxidation activity of soot could be further optimized due to the excellent elevated NO’s conversion rate by partially substituting Cu with K. The maximum particle oxidation rate can be easily realized at such a low temperature as 347°C.     

Coupled heat and mass transfer analysis of NH<Subscript>3</Subscript>-H<Subscript>2</Subscript>O falling film absorption on inner tube surface with low solution flow rates

NH₃-H₂O falling film absorption usually takes place with low solution flow rate in real absorption refrigeration system. An experimental study of inner vertical absorption is carried out for the consideration of air-cooling absorber. Variable working conditions are tested to evaluate the heat and mass transfer performances.The traditional evaluation method based on log-mean-temperature（concentration） difference is criticized for its lack of theoretical basis while simultaneous heat and mass transfer process occurs. A new method proposed by Kim and Infante Ferreira is modified to evaluate the experimental results with reasonable assumptions. The method is based on the derivation of coupled heat and mass transfer differential equations of NH₃-H₂O absorption process.The analysis of the same experimental data shows that the new method realizes better consistency with smaller error, especially in heat transfer aspect. Heat and mass transfer performance is enhanced with the increase of solution Reynolds number. Sub-cooling of inlet weak solution also has positive influence on the absorption process,which should be evaluated by the new method correctly. Two correlations are developed to evaluate both Nusselt and Sherwood numbers for the design of air-cooling absorber.     

Numerical simulation of thermal and iron ore reduction conditions in pre-reduction shaft furnace based on reducing gas composition and temperature

Based on the principles of mass, momentum and heat transfers between the reducing gas and the iron ore solid, a two-dimensional mathematical model for above two phases is established to study the influences of reducing gas composition on thermal and reduction conditions in pre-reduction shaft furnace with the temperature ranging from 1 023 to 1 223K. Due to the strong endothermic effect of iron ore reduction participated by hydrogen (H₂), increasing the ratio of carbon monoxide (CO) to H₂ enlarges high temperature zone under present calculation conditions, thus improves reduction efficiency inside the furnace. In addition, replacing of the reducing gas with an appropriate proportion of nitrogen (N₂) featuring the same temperature has a potential to reduce fuel consumption by as much as 6.5% while the products of similar quality are yielded.     

Monte Carlo simulation of B2-L2<Subscript>1</Subscript> ordering transitions in Au-Cu-Al alloy systems

The B2-L2₁ ordering transitions in Au-Cu-Al shape-memory alloys are studied by the Monte Carlo exchange simulations, where a set of the first, the second and the third nearest-neighbor mixing potentials for Cu-Al in the Au-Cu-Al alloys are calculated from first principals using the Connolly-Williams methods. To ensure the phase stability of the β-Au-Cu-Al, the investigation includes the range of compositions Au₂Cu_1−x Al_1+x (−0.15 ⩽ x ⩽ 0.15). The B2-L2₁ transition temperatures are predicted, and are in agreement with the experimental results. The atomic ordering around vacancy of the L2₁ structure is further discussed.     

Investigation on the formation mechanism of ordered carbide (FeMn)<Subscript>3</Subscript>AlC in the Al added twinning-induced plasticity steels

The spinodal composition zone in Al added Fe-Mn-Al-C twinning-induced plasticity（TWIP） steels can be determined by contents of Al and C and aging temperature together, based on the thermodynamic analysis. Precipitation of ordered（FeMn）₃AlC carbide by the mechanism of spinodal decomposition occurs in the C-rich and Al-rich zone with low aging temperature. Increase of aging temperature shrinks spinodal composition zone to the high Al and C contents. As a result, the precipitation of（FeMn）₃AlC carbide alters from spinodal decomposition to classical nucleation-growth manner gradually. Further calculation indicates that the diffusion of Al can play a key role in determining the growth rate of（FeMn）₃AlC carbide at high aging temperature.     

Combustion optimization model for NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> reduction with an improved particle swarm optimization

Abstract: This paper focuses on the combustion optimization to cut down NO _x emission with a new strategy. Firstly, orthogonal experimental design (OED) and chaotic sequences are introduced to improve the performance of particle swarm optimization (PSO). Then, a predicting model for NO _x emission is established on support vector machine (SVM) whose parameters are optimized by the improved PSO. Afterwards, a new optimization model considering coal quantity and air quantity along with the traditional optimization variables is established. At last, the operating parameters are optimized by the improved PSO to cut down the NO _x emission. An application on 600MW unit shows that the new optimization model can cut down NO _x emission effectively and maintain the load balance well. The NO _x emission optimized by the improved PSO is lowest among some state-of-the-art intelligent algorithms. This study can provide important guides for the low NO _x combustion in the power plant.     

Photothermal effect for Fe3O4 nanoparticles contained in micelles induced by near-infrared light

Near infrared (NIR) light induced photothermal effect for Fe₃O₄ nanoparticles, contained in Pluronic F127 micelles, has been studied and it exhibits high photothermal converting efficiency. Heat is found to be rapidly generated in micelles containing Fe₃O₄ nanoparticles by NIR laser irradiation. Upon irradiation at 808 nm light and with mass concentration of Fe₃O₄ nanoparticles in 4 g/L, the micelle temperature increase is higher than 34°C for 10min irradiation. The maximum temperature of micelles containing Fe₃O₄ nanoparticles in 4 g/L reaches 62°C.     

Scale-invariant occupancy of phase space and additivity of nonextensive entropy <Emphasis Type="Italic">S</Emphasis><Subscript><Emphasis Type="Italic">q</Emphasis></Subscript>

Phase space can be constructed for N equal and distinguishable binary subsystems which are correlated in a scale-invariant manner. In the paper, correlation coefficient and reduced probability are introduced to characterize the scale-invariant correlated binary subsystems. Probabilistic sets for the correlated binary subsystems satisfy Leibnitz triangle rule in the sense that the marginal probabilities of N-system are equal to the joint probabilities of the (N −1)-system. For entropic index q ≠ 1, nonextensive entropy S _q is shown to be additive in the scale-invariant occupation of phase space.     

Research on electron beam welding of in situ TiB<Subscript>2p</Subscript>/ZL101 composite

Electron beam welding of in situ TiB_2p reinforced aluminum composites was studied. The results show that no obvious pores or cracks is presented in the weld seam. The grains in the weld seam are remarkably refined and TiB₂ particles distribute much more homogeneously than that in base metal. The hardness values of fusion zone and heat affected zone (HAZ) are both increased in comparison with that of base metal. There are no interface reactions between TiB₂ particle and Al matrix. This results supply the evidence that the novel TiB_2p reinforced aluminum composites can be well joined with the electron beam welding.     

Improvement of immunoassay detection sensitivity by using well-defined raspberry-like magnetic microbeads as carriers

Well-defined raspberry-like magnetic microbeads(RMMBs) as immunoassay solid carriers were prepared by chemical covalent binding between Fe3O4 magnetic microspheres and SiO2 nanoparticles. These RMMBs were not as agglomerative as nano-sized magnetie particles( 200 nm), which was an advangtage for high efficient magnetic separation. When compared to Fe3O4@SiO2core-shell magnetic microbeads(CMMBs) with smooth surface, RMMBs exhibited stronger capacity to bind biomolecules. Limit of blank(LoB) and limit of detection(LoD) of HBsAg detection using RMMBs as carriers via chemiluminiscence immunoassay(CLIA) were 0.472 and1.022 μg/L, respectively, showing a notable improvement compared with CMMBs whose LoB and LoD were 1.017 and 1.988 μg/L, respectively. All these indicated a great potential of RMMBs in immunoassay application.     

Gain and noise figure analysis of Er<Superscript>3+</Superscript>-doped YAG transparent ceramic microchip amplifier

The rate equations and the power evolution equations based on excited state absorption (ESA) and cooperative upconversion (CUC) of high concentration erbium-doped yttrium aluminum garnet (YAG) transparent ceramic waveguide amplifier are set up to analyze the effects of the pump power, active ion concentration and waveguide length on the amplifier gain and noise figure (NF). The numerical analysis predicts that with a pump power of 100mW, an active ion concentration of 1.0×10²⁶ ion/m³ and a waveguide length of 3 cm, a small-signal gain of 30 dB and an NF of 5 dB can be achieved in the micro-chip amplifier.     

Gain and emission spectrum characteristics of 465nm laser diode pumped Tm<Superscript>3+</Superscript>-doped telluride glass fibers

Gain and emission spectrum characteristics of Tm³⁺-doped telluride glass fibers pumped with 465 nm lasers are analyzed. The rate and power propagation equation groups of the fibers are solved numerically and the effects of the fiber parameters including active ion concentration, length and pump power on the gain spectra and amplified spontaneous emission (ASE) spectra are analyzed. The results show that with a pump parameter of 465 nm/200mW, a doping concentration of 2.5×10²⁵ ion/m³ and a fiber length of 16m, the gain and ASE spectra can cover from 1.100 to 1.900 μm, and the gain and ASE power peaks can reach 52 dB and 8mW, respectively.     

Effects of Heat Intensity and Inflow Wind on the Reactive Pollution Dispersion in Urban Street Canyon

This paper investigates the impacts of heating intensity and inflow wind speed on the characteristics of reactive pollutant dispersion in street canyons using the computational fluid dynamic (CFD) model that includes the transportation of NO, NO₂, and O₃ coupled with NO-NO₂-O₃ photochemistry. The results indicated that the heat intensity and inflow wind speed have a significant influence on the flow field, temperature field and the characteristics of reactive pollutant dispersion in and above the street canyon. With the street canyon bottom heating intensity increasing, NO, NO₂ and O₃ concentrations in street canyon are decreased. The O₃ concentration reductions are even more than the NO and NO₂ concentrations. Improving the inflow wind speed can significantly reduce the NO and NO₂ concentrations within street canyons. But the O₃ concentrations have a slight rise with wind speed increasing. The results would be useful for understanding the interrelation among reactive vehicle emissions, and provide references for urban planners.     

Improvement the electrochemical performance of Li1.2Ni0.2Mn0.6O2 electrode with AlF3 added

Layered solid solution material Li_1.2Ni_0.2Mn_0.6O₂ is synthesized and the AlF₃ is added to improve the electrochemical performance. X-ray diffraction (XRD) results show that the Li_1.2Ni_0.2Mn_0.6O₂ samples exhibit layered characteristics. The AlF₃ additive is detected by transmission electron microscope (TEM) technology. The electrochemical tests show that Li_1.2Ni_0.2Mn_0.6O₂ electrode with AlF₃ added delivers better discharge capacity (240mA· h/g), first coulomb efficiency 79.2%, cyclic performance (capacity retention ratio of 100.6% after 50 cycles), and rate capacity (68mA · h/g at 10 capacity (C)) than the pristine sample. Electrochemical impedance spectroscopy (EIS) results show that the charge transfer resistance of Li_1.2Ni_0.2Mn_0.6O₂ electrode with AlF₃ added increases slower than that of pristine Li_1.2Ni_0.2Mn_0.6O₂ after cycling, which is responsible for better cyclic and rate performance.     

Quantitative phase analysis of the calcium silicate slag as the residue of extracting alumina from high-alumina fly ash

Calcium silicate slag is the residue of process of pre-desilication alkali lime sintering applied in the high-alumina fly ash to extract the alumina. The quantitative phase analysis (QPA) of the calcium silicate slag has been performed by the Rietveld method based on the powder X-ray diffraction (XRD) with the aid of noncommercial software GSAS-EXPGUI. A known weight of crystalline internal standard (10% CaF₂) was added to the calcium silicate slag to calculate the fraction of amorphous phase and other crystalline phases on an absolute basis. Besides, the calcium silicate slag was characterized by X-ray fluorescence (XRF) and thermo gravimetric (TG) differential scanning calorimetry (DSC) to test the QPA results and investigate its other characters. Finally, the results show that the amorphous fraction is 17.5% (hereinafter, the percentages refer to the mass fraction), and the major crystalline phases detected in the calcium silicate slag consist of 23.5% Beta-Ca2SiO₄, 10.0% bredigite, 10.3% Ca₃Al₂O₆ (C₃A) and 21.6% CaCO₃.     

Effect of oxygen content on structural and optical properties of single Cu2O film by reactive magnetron sputtering method

Cuprous oxide (Cu₂O) thin films have been deposited on glass substrate by reactive magnetron sputtering method using Cu target and argon oxygen gas atmosphere. Effect of oxygen flow rate on structural and optical properties of thin films has been discussed. The results of X-ray diffraction, ultraviolet-visible spectrophotometry and atomic force micrograph indicated that the condition window for single Cu₂O phase was about 3.8 to 4.4 cm³/min, and the optimum oxygen flow rate was 4.2 cm³/min. The optical band gap E _g of Cu₂O film was determined by using the data of transmittance versus wavelength, and slightly decreased from 2.46 to 2.40 eV with the increase of oxygen flow rate from 3.8 to 4.4 cm³/min. The Cu₂O film formed at the oxygen flow rate of 4.2 cm³/min had an optical band gap of 2.43 eV.     

Microwave hydrothermal synthesis and characterization of ZnO nanostructures in aqueous solution

ZnO nanostructures were prepared in aqueous solution by microwave hydrothermal synthesis. Xray diffraction (XRD) and field emission scanning electron microscopy (FESEM) were used to characterize ZnO nanostructures (ZNs). The effects of pH, reaction temperature and reaction time on yield of ZnO were investigated. The yield of ZnO increased significantly with the increase of pH value, reaction temperature and reaction time. High yield and well crystallinity of ZNs could be obtained at 120°C for 60min by microwave hydrothermal synthesis. The spherical and rugby-like ZNs were obtained at 120°C without triethanolamine (TEA) and with TEA (mass ratio, $r = m_{Zn^{2 + } }$ : m _TEA = 1: 1), respectively. The concentration of Zn(OH) ₄ ^?2 ions in the reaction solution and TEA had an important effect on the nucleation and morphology of ZnO nanostructures. Mechanism for the formation of ZnO nanostructures was proposed.     

Safety Evaluation for Freeway Exit Ramp Based on Speed Consistency

Speed differential has direct relationship with road safety. Conventional speed consistency measures draw sample data from independent population that follows a normal distribution. These methods may fall into ecological fallacy and overestimate the safety level of road elements. After deducing the relationship between the difference in operating speed ΔV₈₅ and85(ΔV), the 85^th percentile value of individual speed reduction, this paper recommends 85(ΔV) and speed reduction rate 85(ΔV)R is used to evaluate ramp safety. Point speeds of individual vehicle at freeway diverge area, upper ramp, and lower ramp are collected by radar guns. Safety performance of 37 exit ramps are appraised using three different measures, namely, ΔV₈₅, 85(ΔV), and 85(ΔV)R. The results show that 85(ΔV) is 1.42 to 2.02 times of ΔV₈₅, and that the evaluation result of 85(ΔV)R is between the other two. The measure 85(ΔV)R considers not only individual speed but also the base speed on upstream element, which avoid the pitfalls of ecological fallacy and overestimation possessed by conventional measures. It is a safer and reasonable measure that should be adopted in practice.     

Modified Nafion polymer electrolyte membranes by ��-ray irradiation used in direct methanol fuel cells

Modification of the commercial polymer electrolyte membrane (PEM) Nafion 117 by ??-ray irradiation to produce an improved proton exchange membrane for direct methanol fuel cells (DMFCs) was described. The Nafion 117 membrane was exposed under ??-ray irradiation circumstance with the irradiation doses from 10³ to 10⁵ Gy. Subsequently the properties of the membrane itself, in terms of swelling ratio, water uptake rate, proton conductivity and methanol permeability, together with the performance of its membrane electrode assembly (MEA) in DMFC were analyzed and contrasted with the untreated material. When the Nafion 117 membrane was exposed under ??-ray irradiation circumstance, the degradation and crosslinking reactions occurred at the same time. Specific scopes of the ??-ray irradiation dose may cause the membrane crosslinking, thus reduce the membrane swelling ratio and decrease the methanol crossover. By reducing the membrane swelling ratio and methanol permeation, the single DMFC with the modified Nafion 117 membrane produced reasonable power density performance as high as 32W/m² under 2mol/L methanol solution at room temperature.