Study on flange climb derailment criteria of a railway wheelset

The wheel flange climb derailment, which can be usually considered as a quasi-static process, is one of the main types of derailment, and often occurs on curved tracks due to large wheel lateral force and reduced vertical force. The general formula for the wheel critical derailment coefficient Q/P, the ratio of wheel lateral force to vertical force, is derived through analysing the forces exerted on the flange climb wheel. Based on the Coulomb's friction law and the creep force laws, the Friction Formula and Creep Formula for the evaluation of derailment are derived, respectively. The analysis shows that the derailment coefficients of Friction Formula and Creep Formula required for derailment are increased considerably for smaller and negative yaw angles, and tend to the value of Nadal's Formula at larger wheelset yaw angles. The Creep Formula is more reasonable for the assessment of derailment. The effect of some parameters on flange climb derailment, such as wheel/rail friction coefficient, yaw angle, flange contact angle, wheel vertical load and curve radius, are investigated. Finally, a simplified formula for wheel climb derailment based on the Creep Formula is proposed.     

Study on the derailment behaviour of a railway wheelset with solid axles in a railway turnout

ABSTRACT

Dynamic wheel–rail interaction in railway turnouts is more complicated than on ordinary track. In order to evaluate the derailment behaviour of railway wheelsets in railway turnouts, this paper presents a study of dynamic wheel–rail interaction during a wheel flange climbs on the turnout rails, by applying the elasticity positioning wheelset model. A numerical model is established based on a coupled finite element method and multi-body dynamics, and applied to study the derailment behaviour of a railway wheelset in both the facing and trailing directions in a railway turnout, as well as dynamic wheel–turnout rail interaction during the wheel flange climbing on the turnout rails. The influence of the wheel–rail attack angle and the friction coefficient on the dynamic derailment behaviour is investigated through the proposed model. The results show that the derailment safety for a wheelset passing the railway turnout in facing direction is significantly lower than that for the trailing direction and the ordinary track. The possibility of derailment for the wheelset passing the railway turnout in facing and trailing directions at positive wheel–rail attack angles will increase with an increase in the attack angles, and the possibility of derailment can be reduced by decreasing the friction coefficient.     

The stability mechanism and its application to heavy-haul couplers with arc surface contact

To investigate the stability mechanism of a type of heavy-haul coupler with arc surface contact, the force states of coupler were analysed at different yaw angles according to the friction circle theory and the structural characteristics of this coupler were summarised. A multi-body dynamics model with four heavy-haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability was tested in order to investigate the effect of relevant parameters on the coupler stability. The results show that this coupler exhibits the self-stabilisation and less lateral force at a small yaw angle. The yaw angle of force line is less than the actual coupler yaw angle which reduces the lateral force and the critical instability. An increase in the friction coefficient of the arc contact surfaces can improve the stability of couplers. The friction coefficient needs to be increased with the increase in the maximum coupler longitudinal compressive force. The stability of couplers is significantly enhanced by increasing the secondary suspension stiffness and reducing the clearance of the lateral stopper of the locomotives. When the maximum coupler compressive force reaches 2500 kN, the required friction coefficient reduces from 0.6 to 0.35, which notably lowers the derailment risk caused by the coupler. The critical instability angle of the coupler mainly depends on the arc contact friction coefficient. When the friction coefficient is 0.3, the critical instability angle was 4–4.5°. The simulation results are consistent with the locomotive line tests. These studies establish meaningful improvements for the stability of couplers and match the heavy-haul locomotive with its suspension parameters.     

Experimental and numerical investigation on the derailment of a railway wheelset with solid axle

This paper presents the results of an experimental and numerical investigation on the derailment of a railway wheelset with solid axle. Tests were carried out under quasi-steady-state conditions, on a full-scale roller rig, and allowed to point out the effect of different parameters like the wheelset's angle of attack and the ratio between the vertical loads acting on the flanging and non-flanging wheels. On the basis of the test results, some existing derailment criteria are analysed in this paper and two new criteria are proposed. A model of wheel–rail contact is proposed for the mathematical modelling of the flange climb process, and numerical vs. experimental comparisons are used to obtain model validation.     

Dynamic performances of an innovative coupler used in heavy haul trains

An innovative structure for a heavy haul coupler with an arc surface contact and restoring bumpstop is proposed. This coupler has a small lateral force at a small yaw angle and a limitable yaw angle to ensure an allowable coupler lateral force under intense compressive force. The main structural characteristic of the combined contact coupler is a lateral movable follower with an appropriate friction coefficient of 0.06–0.08 and a slide block with a single freedom of longitudinal movement. In order to verify and simulate the performances, a multi-body dynamics model with four heavy haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability and wheel set lateral forces were tested in order to investigate the effect of relevant parameters on the coupler performances. The combined contact coupler is suitable for heavy haul train for a good dynamic performance.     

Drive control system design for stability and maneuverability of a 6WD/6WS vehicle

This paper describes a drive controller designed to improve the lateral vehicle stability and maneuverability of a 6-wheel drive / 6-wheel steering (6WD/6WS) vehicle. The drive controller consists of upper and lower level controllers. The upper level controller is based on sliding control theory and determines both front and middle steering angle, additional net yaw moment, and longitudinal net force according to the reference velocity and steering angle of a manual drive, remotely controlled, autonomous controller. The lower level controller takes the desired longitudinal net force, yaw moment, and tire force information as inputs and determines the additional front steering angle and distributed longitudinal tire force on each wheel. This controller is based on optimal distribution control and takes into consideration the friction circle related to the vertical tire force and friction coefficient acting on the road and tire. Distributed longitudinal/lateral tire forces are determined as proportion to the size of the friction circle according to changes in driving conditions. The response of the 6WD/6WS vehicle implemented with this drive controller has been evaluated via computer simulations conducted using the Matlab/Simulink dynamic model. Computer simulations of an open loop under turning conditions and a closed-loop driver model subjected to double lane change have been conducted to demonstrate the improved performance of the proposed drive controller over that of a conventional DYC.     

Influence of creep forces on the risk of derailment of railway vehicles

The derailment mechanism in a railway vehicle is a complex mechanical phenomenon which has been, and still is, the subject of intense research activity due to the serious consequences it can entail. Since Nadal deduced his well-known formula, many researchers have put forward alternative equations which all attempt to move closer to the data obtained experimentally. This paper provides a summary of the best known and draws up a new formulation based on the theoretical 3-D study of creep forces emerging from the contact patch of the wheel likely to derail. It also provides an in-depth analysis of the role played by spin creepage, including its effect on obtaining theoretical derailment limits, which are more realistic than those obtained using Nadal's formula. Finally, a new derailment criterion is proposed. This new criterion leads to less conservative values than Nadal's equation for zero yaw angles. When the yaw angle is high enough, the results obtained are coincident with those predicted by Nadal's equation.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

Experimental and numerical investigation on the derailment of a railway wheelset with solid axle

This paper presents the results of an experimental and numerical investigation on the derailment of a railway wheelset with solid axle. Tests were carried out under quasi-steady-state conditions, on a full-scale roller rig, and allowed to point out the effect of different parameters like the wheelset's angle of attack and the ratio between the vertical loads acting on the flanging and non-flanging wheels. On the basis of the test results, some existing derailment criteria are analysed in this paper and two new criteria are proposed. A model of wheel-rail contact is proposed for the mathematical modelling of the flange climb process, and numerical vs. experimental comparisons are used to obtain model validation.     

Effect of curved track support failure on vehicle derailment

In order to investigate the effect of curved track support failure on railway vehicle derailment, a coupled vehicle–track dynamic model is put forward. In the model, the vehicle and the structure under rails are, respectively, modelled as a multi-body system, and the rail is modelled with a Timoshenko beam rested on the discrete sleepers. The lateral, vertical, and torsional deformations of the beam are taken into account. The model also considers the effect of the discrete support by sleepers on the coupling dynamics of the vehicle and track. The sleepers are assumed to move backward at a constant speed to simulate the vehicle running along the track at the same speed. In the calculation of the coupled vehicle and track dynamics, the normal forces of the wheels/rails are calculated using the Hertzian contact theory and their creep forces are determined with the nonlinear creep theory by Shen et al [Z.Y. Shen, J.K. Hedrick, and J.A. Elkins, A comparison of alternative creep-force models for rail vehicle dynamic analysis, Proceedings of the 8th IAVSD Symposium, Cambridge, MA, 1984, pp. 591–605]. The motion equations of the vehicle/track are solved by means of an explicit integration method. The failure of the components of the curved track is simulated by changing the track stiffness and damping along the track. The cases where zero to six supports of the curved rails fail are considered. The transient derailment coefficients are calculated. They are, respectively, the ratio of the wheel/rail lateral force to the vertical force and the wheel load reduction. The contact points of the wheels/rails are in detail analysed and used to evaluate the risk of the vehicle derailment. Also, the present work investigates the effect of friction coefficient, axle load and vehicle speed on the derailments under the condition of track failure. The numerical results obtained indicate that the failure of track supports has a great influence on the whole vehicle running safety.     

Dynamic performance of high-speed train passing windbreak breach under unsteady crosswind

Field test and computational fluid dynamics (CFD) method are conducted to investigate the safety of high-speed train under unsteady crosswind. Wheel–rail forces of high-speed train passing a breach between two windbreaks under strong crosswind are measured in a field test. The derailment coefficient of first wheelset of front car at the windward side reaches the allowable value. Meanwhile, the left and right of lateral wheel–rail force are in the opposite direction. This kind of phenomenon has not been tested before. Therefore, CFD and multi-body simulations are performed in order to study the phenomena. Good agreement is obtained between the simulation results and the experimental data. It is concluded that the sudden increase of transient aerodynamic loads, when the train passing the breach, is the root of this phenomenon; after running along the same direction as carbody and bogie run along the opposite direction during the high-speed train passing the windbreak breach; larger opposite longitudinal creeping forces of first wheelset compel the first wheelset to yaw toward the windward side; meanwhile, larger lateral wheel–rail forces compel the first wheelset to run toward the windward side rail; the left and right lateral wheel–rail forces become opposite because the right wheel impacts the windward side rail.     

Safety of a railway wheelset – derailment simulation with increasing lateral force

The motivation for this research is to make a comparison between dynamic results of a free railway wheelset derailment and safety limits. For this purpose, a numerical simulation of a wheelset derailment submitted to increasing lateral force is used to compare with the safety limit, using different criteria. A simplified wheelset model is used to simulate derailments with different adhesion conditions. The contact force components, including the longitudinal and spin effects, are identified in a steady-state condition on the verge of a derailment. The contact force ratios are used in a three-dimensional (3D) analytical formula to calculate the safety limits. Simulation results obtained with two contact methods were compared with the published results and the safety limit was identified with the two criteria. Results confirm Nadal’s conservative aspect and show that safety 3D analytical formula presents slightly higher safety limits for lower friction coefficients and smaller limits for high friction, in comparison with the simulation results with Fastsim.     

Three-dimensional derailment analysis of a crashed city tram

City tram collisions are simulated using multi-body dynamics. The aim of this paper is to investigate the collision-induced derailment. Simulation results demonstrate that the corner obstacle collision scenario defined in EN 15227 is mainly focused on the energy absorption process. Due to the large impact angle (45°), it is unlikely for a city tram to comply with this scenario without derailment. In order to avoid derailment, the maximum impact angle between city tram and oblique obstacle should be reduced to 25°. Moreover, some influence factors are analysed, such as mass of loaded passengers, friction coefficient, impact angle, etc. Derailment phenomenon is shown to be significantly dependent on these parameters. Two measures are proposed to prevent the collided city tram from derailment. One is using secondary lateral dampers to absorb collision energy. Another is increasing the lateral stiffness of secondary springs as well as the lateral clearance, so that more collision energy can be stored in the suspension. With these measures, the safety against derailment can be improved.     

Multi-axle vehicle dynamics stability control algorithm with all independent drive wheel

The stability driving characteristic and the tire wear of 8-axle vehicle with 16-independent driving wheels are discussed in this paper. The lateral stability of 8-axle vehicle can be improved by the direct yaw moment which is generated by the 16 independent driving wheels. The hierarchical controller is designed to determine the required yaw torque and driving force of each wheel. The upper level controller uses feed-forward and feed-backward control theory to obtain the required yaw torque. The fuzzification weight ratio of two control objective is built in the upper level controller to regulate the vehicle yaw and lateral motions. The rule-based yaw moment distribution strategy and the driving force adjustment based on the safety of vehicle are proposed in the lower level controller. The influence of rear steering angle is considered in the distribution of driving force of the wheel. Simulation results of a vehicle double lane change show the stability of 8-axle vehicle under the proposed control algorithm. The wear rate of tire is calculated by the interaction force between the tire and ground. The wear of tire is different from each other for the vehicle with the stability controller or not.     

Analysis of the car body stability performance after coupler jack-knifing during braking

This paper aims to improve car body stability performance by optimising locomotive parameters when coupler jack-knifing occurs during braking. In order to prevent car body instability behaviour caused by coupler jack-knifing, a multi-locomotive simulation model and a series of field braking tests are developed to analyse the influence of the secondary suspension and the secondary lateral stopper on the car body stability performance during braking. According to simulation and test results, increasing secondary lateral stiffness contributes to limit car body yaw angle during braking. However, it seriously affects the dynamic performance of the locomotive. For the secondary lateral stopper, its lateral stiffness and free clearance have a significant influence on improving the car body stability capacity, and have less effect on the dynamic performance of the locomotive. An optimised measure was proposed and adopted on the test locomotive. For the optimised locomotive, the lateral stiffness of secondary lateral stopper is increased to 7875?kN/m, while its free clearance is decreased to 10?mm. The optimised locomotive has excellent dynamic and safety performance. Comparing with the original locomotive, the maximum car body yaw angle and coupler rotation angle of the optimised locomotive were reduced by 59.25% and 53.19%, respectively, according to the practical application. The maximum derailment coefficient was 0.32, and the maximum wheelset lateral force was 39.5?kN. Hence, reasonable parameters of secondary lateral stopper can improve the car body stability capacity and the running safety of the heavy haul locomotive.     

Optimal Control of Four Wheel Steering Vehicle

This paper derives a method of controlling four wheel steering using optimal control theory. The purpose of control is to minimize the sideslip angle at the center of gravity. The control method feeds forward the steering wheel angle and feeds back the yaw velocity and the sideslip angle to the front and rear wheel angles. Theoretical studies show that the sideslip angle is reduced to zero even in the transient state, and that the understeer characteristic and frequency response can be changed regardless of the vehicle static margin. This Paper also examines various characteristics of the influence of the side force nonlinearities of tires and crosswinds.     

The stability and mechanical characteristics of heavy haul couplers with restoring bumpstop

To investigate the stability and mechanical characteristics of a type of heavy haul coupler with restoring bumpstop, the geometry and force states of couplers were analysed at different yaw angles and the longitudinal forces. The structural characteristics of this coupler were summarised. To aid in the investigation, a multi-body dynamics model with four heavy haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability and lateral forces were tested in order to investigate the effect of relevant parameters on the locomotive's wheelset lateral forces. The results show that only when the bumpstop force exceeds half of the coupler longitudinal compression force, can the follower be rotated and the yaw angle of the coupler increase. The bumpstop preload is the most important stabilising factor. The coupler lateral force is constant when the coupler longitudinal force is smaller than the critical values of 2000, 1400 and 1150 kN at coupler free angles of 7°, 8° and 9°, respectively, for operation on straight track. The coupler free angle and the locomotive's lateral clearance of the secondary stopper are important in decreasing the wheelset lateral forces of the locomotive. It is advised that a smaller locomotive's secondary lateral suspension stiffness, a free clearance of 35 mm and an elastic clearance of 15 mm from the secondary lateral stopper be selected. If the coupler's free angle is less than the self-stabilising angle which is 5.5° for operation on straight track, the coupler is stable no matter how great the longitudinal force is. The wheelset lateral forces are allowed at the coupler longitudinal force of 2500 kN when the free angle is 6°. These studies establish meaningful improvements for the stability of couplers and match the heavy haul locomotive with its suspension parameters.     

The mechanism for the coupler and draft gear and its influence on safety during a train collision

A mechanical model of the coupler and draft gear was established to study the mechanism during an intercity train collision. The model includes four rigid bodies, one spherical joint, two nonlinear torsion spring units and two nonlinear hysteresis units. Simulation and test results show that the axial characteristics of the model are reasonable and the model can reasonably simulate the pitching movement of the coupler. The influence of the coupler and draft gear on the collision behaviour of the train is analysed considering a four-section intercity train. The results show that during the collision process, the amount of compression of the middle coupler is an important factor influencing the pitching deflection angle. The pitching motion posture of the coupler changes with the initial pitching deflection angle, but the initial pitching deflection angle has little effect on its yawing deflection angle. When the pitching angle of the middle coupler is elevated, as the elevation angle increases, the derailment risk of the ‘A’ end bogie of the previous vehicle increases, whereas the risk of derailment of the ‘B’ end bogie of the subsequent vehicle decreases. When the pitching angle of the middle coupler is depressed, the derailment trends for the front and rear bogies exhibit the opposite trend from that of the elevation angle. As the train collision speed increases, the pitching motion of the middle coupler is limited to forcing a yawing motion, causing the yawing deflection angle to increase sharply, which causes the wheel–rail lateral force to increase rapidly. From this, the derailment risk of the bogie increases, which further causes large displacement lateral buckling of the train. An anti-lateral buckling device can limit the yawing deflection angle of the middle coupler, preventing lateral buckling from large displacement and decreasing the risk of derailment.     

平移模式下挡土墙墙背土侧压力系数的计算

根据库仑土压力理论中墙背滑动楔体整体达到静平衡的基本原理，假定沿墙高方向，土与墙背的摩擦角均达到极限值，从墙背处土体主应力偏转的应力状态分析出发，得到墙背处的主应力偏转角和土侧压力系数的计算公式；把土侧压力系数用于水平层分析法，建立了竖向土压力的基本方程，求解该方程，导出了挡土墙主动土压力、土压力合力及其作用位置的理论公式。经比较，该方法与其他方法对土侧压力系数的计算结果基本一致，所得的挡土墙主动土压力计算结果与模型试验结果也较为吻合。     

Dynamics of railway wagons subjected to braking/traction torque

Braking or traction torque is regarded as an important source of wheelset skid and a potential source of derailment risk that adversely affects the safety levels of train operations; therefore, this research examines the effect of braking/traction torque to the longitudinal and lateral dynamics of wagons. This paper reports how train operations safety could be adversely affected due to various braking strategies. Sensitivity of wagon dynamics to braking severity is illustrated through numerical examples. The influence of wheel/rail interface friction coefficient and the effects of two types of track geometry defects on wheel unloading ratio and wagon pitch are also discussed in the paper.