基于试验获取主应力应变曲线的油船极限强度评估研究(英文)

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

Ultimate strength assessment of a tanker hull based on experimentally developed master curves

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

基于广义切线模量理论的铝合金加筋板结构轴压极限强度分析

研究铝合金加筋板结构的极限强度,有利于充分发挥铝合金材料的强度潜力和结构的后屈曲承载能力。本文将广义切线模量理论应用于铝合金加筋板结构的轴压极限强度计算,并推导了适用于加筋板的协调参数、极限弯矩系数及结构系数等相关参数的解析算式,建立了铝合金加筋板结构的强度利用率函数,从而得到结构的极限强度,进一步完善了广义切线模量理论在加筋板结构极限强度研究领域的应用。通过将广义切线模量法计算结果与经验公式、有限元计算结果进行比较,验证了其适用性与可靠性,可用于工程分析计算。     

Ultimate strength assessment of simply supported pitted platings: A new stochastic approach based on Monte Carlo simulation

The ultimate strength assessment of platings affected by random corrosion wastage is a key factor for the reliable design of new ships and the structural health monitoring of aged structures, as pitting corrosion wastage significantly affects the ultimate capacity of platings under compression. In this respect, significant efforts have been undertaken in the last decade to assess the ultimate strength drop-off of pitted platings under compression and several interpolating design formulas, based on a large number of FE simulations, have been developed. Nevertheless, current Rules and guidelines don't provide any explicit strength check criterion for pitted platings. Hence, the main aim of current research is the development of a new framework for the ultimate strength assessment of pitted platings, based on a stochastic approach and the endorsement of Monte Carlo simulation. A new formula, which allows evaluating the statistical properties of the plating ultimate strength in presence of random corrosion wastage, is developed. Subsequently, a benchmark study is carried out, to compare the new formula with the existing ones available in literature and a wide set of FE simulations, carried out by Ansys APDL. Current results are discussed, and the effectiveness of the new formula is verified.     

含点蚀损伤船体加筋板在纵向压力下的极限强度

针对老龄化船舶结构上的点状腐蚀,利用非线性有限元方法进行计算,分析304个船体加筋板的极限强度,探讨带板柔度、加强筋柔度、腐蚀面积比和腐蚀深度比对纵向压力下含点蚀损伤船体加筋板极限强度的影响,拟合出点状腐蚀下船体加筋板极限强度折减公式并对其适用性进行验证,研究结果具有一定的工程参考意义和价值。     

Comparisons of calculations with experiments on the ultimate strength of wide stiffened panels

Five specimens of wide stiffened panel with four stiffeners under axial compression until collapse are studied with a nonlinear finite element analysis and Common Structural Rules to compare with the experimental results. The stiffened panel models have two longitudinal bays to produce reasonable boundary condition at the end of edges. Tension tests have been conducted to obtain the material properties of the steel that are used in the finite element analysis. Three boundary condition configurations are adopted to investigate their influence on the collapse behaviour of the stiffened panels. A displacement transducer was used to measure the initial geometrical imperfections of the stiffened plates. The collapse behaviour of the stiffened panels is analysed in finite element analysis with the measured initial imperfections and with nominal imperfections. An equivalent initial imperfection is validated for the ultimate strength of stiffened panel under compressive load until collapse for the panels under consideration. With the same imperfection amplitude, the shape of the column-type initial deflection of stiffeners affects significantly the collapse shape, but only slightly the ultimate strength and the mode of collapse of the stiffened panels. The 1/2 + 1 + 1/2 bays model with restrained boundary condition BC3 gives an adequate FE modelling and is possible to be fabricated in experiment.     

大型加强板结构焊接顺序的效果研究(英文)

Welding sequence has a significant effect on distortion pattern of large orthogonally stiffened panels normally used in ships and offshore structures. These deformations adversely affect the subsequent fitup and alignment of the adjacent panels. It may also result in loss of structural integrity. These panels primarily suffer from angular and buckling distortions. The extent of distortion depends on several parameters such as welding speed, plate thickness, welding current, voltage, restraints applied to the job while welding, thermal history as well as sequence of welding. Numerical modeling of welding and experimental validation of the FE model has been carried out for estimation of thermal history and resulting distortions. In the present work an FE model has been developed for studying the effect of welding sequence on the distortion pattern and its magnitude in fabrication of orthogonally stiffened plate panels.     

A study on scantling formulae of plate members due to lateral pressure under the effect of axial loads

Existing rule scantling formulae of plate members are based on conventional plastic design theory, and do not necessarily reflect complicated plate bending phenomena under axial loads. In this study, we first formulated the effect of axial load on the fully plastic moment based on the von Mises yield criterion for longitudinally stiffened plate in addition to the well-known formula for transversely stiffened plate. In addition, we derived a theoretical formulation of the lateral pressure corresponding to 2-point hinge and 3-point hinge formation taking account of the effect of the additional lateral force due to the axial loads on the deflected plating, using a simple plate strip bending model assuming a long plate with a large aspect ratio.Then, a series of elastic-plastic FE analyses was carried out to verify the structural behavior and the effect of axial load on the plate plastic bending strength. The plate strength was evaluated based on the residual deflection criteria of two cases (0.26 mm and 4.0 mm), and the results were compared with the theoretical derivation. As a result, it was found that assumption of linear strength reduction to the axial stress can cover the transversely stiffened plate under compressive axial stress conservatively. As to the transversely stiffened plate under tensile axial stress and the longitudinally stiffened plate, the strength reduction was in accordance with the reduction in the fully plastic moment based on the von Mises yield criterion in the conservative side. Finally, based on the findings, the required plate thickness coefficients were proposed on an empirical basis both for transversely and longitudinally stiffened plate under compressive and tensile axial loads.     

具有裂纹缺陷的加筋板的剩余拉伸强度分析

对具有裂纹缺陷的加筋板的剩余强度进行了数值分析.考虑了加筋板上的三种缺陷形式,即板和筋上的垂直裂纹,板和筋上的倾斜裂纹以及板上的裂纹和筋上的圆孔.对板和筋上的相对裂纹长度、材料属性、板和筋的厚度、裂纹开裂角度以及圆孔的直径等影响参数进行了分析.同时,将无加筋板剩余强度的经验公式推广到加筋板,并验证了公式的有效性.     

复合材料船体纵向极限强度可靠性分析

把船体甲板或船底板结构视为是一系列加筋板单元的组合，然后利用复合材料梁柱理论计算船体加筋板单元构件的极限承载能力，最后用Smith法计算复合材料船体的极限承载能力。由于复合材料船体纵向极限强度的极限状态方程不能简单地用船体各参数显式表达，故将近年发展起来的响应面法与JC法相结合，对复合材料船体纵向极限强度进行了可靠性分析。并讨论了影响船体纵向极限强度可靠性各变量的敏感性。     

Evaluation of ultimate strength of stiffened panels under longitudinal thrust

A series of collapse analyses is performed applying nonlinear FEM on stiffened panels subjected to longitudinal thrust. MSC.Marc is used. Numbers, types and sizes of stiffeners are varied and so slenderness ratio as well as aspect ratio of local panels partitioned by stiffeners keeping the spacing between adjacent longitudinal stiffeners the same. Initial deflection of a thin-horse mode is imposed on local panels and that of flexural buckling and tripping modes on stiffeners to represent actual initial deflection in stiffened panels in ship structures. On the basis of the calculated results, buckling/plastic collapse behaviour of stiffened panels under longitudinal thrust is investigated. The calculated ultimate strength are compared with those obtained by applying several existing methods such as CSR for bulk carriers and PULS. Simple formulas for stiffened panels, of which collapse is dominated fundamentally by the collapse of local panels between longitudinal stiffeners, are also examined if they accurately estimate the ultimate strength. Through comparison of the estimated results with the FEM results, it has been concluded that PULS and modified FYH formulas fundamentally give good estimation of the ultimate strength of stiffened panels under longitudinal thrust.     

Patran的PCL语言在板格和加筋板极限强度计算中的运用

用Fortran编写程序生成Patran的.ses文件,可将任意指定的初始挠度施加到要计算分析极限强度的光板和加筋板结构模型中去.具体分析6块光板和4块加筋板结构的极限强度,计算结果表明,该方法可以模拟任意复杂的变形形式,从而更加准确地计算和评估加筋板结构的极限强度.     

Sensitivity analysis on ultimate strength of aluminium stiffened panels

This paper presents the results of an extensive sensitivity analysis carried out by the Committee III.1 “Ultimate Strength” of ISSC’2003 in the framework of a benchmark on the ultimate strength of aluminium stiffened panels.Previously, different benchmarks were presented by ISSC committees on ultimate strength. The goal has typically been to give guidance to the designer on how to predict the ultimate strength and to indicate what level of accuracy would be expected.This time, the target of this benchmark is to present reliable finite element models to study the behaviour of axially compressed stiffened aluminium panels (including extruded profiles). Main objectives are to compare codes/models and to perform quantitative sensitivity analysis of the ultimate strength of a welded aluminium panel on various parameters (typically the heat-affected zone).Two phases were planned. In Phase A, all members analysed the same structure with a defined set of parameters and using different codes. It was expected that all the codes/models predict the same results. In Phase B, to boost the scope of the analysis, the different members (using their own model) performed FE analyses for a range of variation of different parameters (sensitivity analysis).     

加筋板极限压缩强度的对传神经网络计算

基于大量实验结果,提出了用对传神经网络（ＣＰＮ）计算加筋板极限强度的方法。与近年 来提出的双参数拟合多项式比较,ＣＰＮ可考虑更多的设计参数,并充分利用实验数据,因此拟 合精度更高。     

无加筋平板极限强度的简化解析法与规范公式的比较

无加筋板是船舶结构的主要构件之一，船舶结构强度校核的一项重要内容就是校核各平板单元是否具备足够的强度储备。最近几年，作者们采用弹性大挠度理论和刚塑性分析相结合的简化解析方法，曾给出了板和加筋板格在联合载荷作用下的极限强度计算公式，并与部分实验值相比，吻合较好，但没有与目前船级社所采用的规范计算公式作过比较。现作这一比较工作，也包括与有限元分析的比较；同时对以前所开发的简化解析法又作了进一步的改进，文章报道这一改进结果。最后，采用上述三种方法，对影响平板极限强度的几个主要参数进行了研究，结果表明，简化解析法与规范计算公式吻合较好。     

加筋板格高级屈曲分析技术研究及软件开发

文章给出了基于弹性大挠度理论和刚塑性分析的加筋板格高级屈曲分析方法(EPM),该方法包括五种失效模式,即正交加筋板格整体屈曲、纵向加筋子板格整体屈曲、纵向加筋和带板的局部屈曲或屈服、纵向加筋的侧倾以及全部屈服,可以考虑初始挠度和残余应力的影响以及双向压缩和侧向载荷的联合作用。以EPM方法为核心开发了加筋板格高级屈曲分析软件系统,包括任务管理、数据输入、屈曲分析、结果查看、能力曲线和文件分析等六个模块。为验证EPM方法的精度进行了系列纵向加筋和正交加筋板格试验模型的比较计算,并计算了四种典型加筋板格的双向应力能力曲线,与板格极限状态分析（PULS）软件和协调共同结构规范（HCSR）方法进行了比较分析。结果表明EPM方法可以分析联合载荷等因素对加筋板格极限强度的影响,文中开发的软件系统可用于加筋板格高级屈曲分析。     

Ultimate strength assessment of stiffened panel under uni-axial compression with non-linear equivalent single layer approach

Steel stiffened panels are widely used in engineering design and construction. However, numerical modeling and analysis effort for a three-dimensional (3D) stiffened panel may be notable, especially for the ultimate limit state of ship structures. Therefore, a homogenization method is outlined that transforms 3D stiffened panel into an Equivalent Single Layer (ESL) concerning the same mechanical behavior. ESL stiffnesses are obtained with a unit cell analyses based on stiffened panel where periodicity is imposed with boundary conditions based on a first-order shear deformation theory (FSDT). Stiffnesses were determined from the first derivative of a membrane force and bending moment obtained with numerical simulations. The effect of initial imperfection shape was included in the analysis to account for local and global buckling behavior. ESL with non-linear stiffness was implemented in Abaqus UGENS subroutine, allowing incremental evaluation of stiffness. Ultimate strength prediction of a steel grillage model with ESL finite element analysis was in excellent agreement with detailed 3D FEM analysis. The key in this analysis was consideration of non-linear ESL stiffness as linear analysis was unable to detect the point where ultimate strength capacity of the grillage was reached.     

联合弯矩作用下含裂纹船体结构剩余极限强度评估方法研究

裂纹损伤对于船体结构来说难以避免,将削弱结构的极限强度,所以研究含裂纹损伤船体结构的剩余极限强度意义重大.对于含裂纹舱段结构,现有的研究主要针对垂向弯矩作用下的剩余极限强度,对于联合弯矩作用下的研究还很欠缺.本文采用非线性有限元分析方法,研究了垂向弯矩和水平弯矩联合作用下含裂纹舱段的剩余极限强度.提出了计算含裂纹船舯舱段在联合弯矩作用下剩余极限强度的计算公式,通过对含裂纹箱型梁的有限元计算结果进行拟合,得到公式中待定系数的表达式.研究结果表明,本文提出的方法可以快速预测船体结构在联合弯矩作用下的剩余极限强度.     

Prediction of hull girder moment-carrying capacity using kinematic displacement theory

The hull girder moment capacity of a very large crude oil carrier (VLCC) called Energy Concentration (EC), for which many benchmark studies have been carried out using the simple progressive collapse method (SPCM), is predicted. In this study, three approaches are used to represent the load-shortening behavior, so-called average compressive strength, of a stiffened panel, comprising the hull section: 1) kinematic displacement theory (KDT); 2) nonlinear finite element analysis (FEA); and 3) simple formulas in the common structural rule (CSR) for tankers. Load-shortening curves for various kinds of stiffened panels in EC are compared for five different scenarios with variations of load-shortening approaches and initial imperfections. In order to verify the effect of load-shortening on the prediction accuracy of the hull girder moment-carrying capacity, load-shortening curves are imported into an SPCM-based in-house program called Ultimate Moment Analysis of Damaged Ships (UMADS). Comparison of the hull girder ultimate strength for general heeling conditions, including hogging and sagging conditions, reveals that the load-shortening curves significantly affect the hull girder moment-carrying capacities. Based on our comparison of these capacities with other benchmark results, it is concluded that nonlinear FEA provided the most conservative results, KDT provided the second most conservative results, and the CSR formulas predicted the upper bound.