Development of two driving cycles for utility vehicles

Driving cycles are used to assess vehicle fuel consumption and pollutant emissions. The premise in this article is that suburban road-work vehicles and airport vehicles operate under particular conditions that are not taken into account by conventional driving cycles. Thus, experimental data were acquired from two pickup trucks representing both vehicle fleets that were equipped with a data logger. Based on experimental data, the suburban road-work vehicle showed a mixed driving behavior of high and low speed with occasional long periods of idling. In the airport environment, however, the driving conditions were restricted to airport grounds but were characterized by many accelerations and few high speeds. Based on these measurements, microtrips were defined and two driving cycles proposed. Fuel consumption and pollutant emissions were then measured for both cycles and compared to the FTP-75 and HWFCT cycles, which revealed a major difference: at least a 31% increase in fuel consumption over FTP-75. This increased fuel consumption translates into higher pollutant emissions. When CO₂ equivalent emissions are taken into account, the proposed cycles show an increase of at least 31% over FTP-75 and illustrate the importance of quantifying fleet speed patterns to assess CO₂ equivalent emissions so that the fleet manager can determine potential gains in energy or increased pollutant emissions.     

Hardware-in-the-loop testbed for evaluating connected vehicle applications

Connected vehicle environment provides the groundwork of future road transportation. Researches in this area are gaining a lot of attention to improve not only traffic mobility and safety, but also vehicles’ fuel consumption and emissions. Energy optimization methods that combine traffic information are proposed, but actual testing in the field proves to be rather challenging largely due to safety and technical issues. In light of this, a Hardware-in-the-Loop-System (HiLS) testbed to evaluate the performance of connected vehicle applications is proposed. A laboratory powertrain research platform, which consists of a real engine, an engine-loading device (hydrostatic dynamometer) and a virtual powertrain model to represent a vehicle, is connected remotely to a microscopic traffic simulator (VISSIM). Vehicle dynamics and road conditions of a target vehicle in the VISSIM simulation are transmitted to the powertrain research platform through the internet, where the power demand can then be calculated. The engine then operates through an engine optimization procedure to minimize fuel consumption, while the dynamometer tracks the desired engine load based on the target vehicle information. Test results show fast data transfer at every 200 ms and good tracking of the optimized engine operating points and the desired vehicle speed. Actual fuel and emissions measurements, which otherwise could not be calculated precisely by fuel and emission maps in simulations, are achieved by the testbed. In addition, VISSIM simulation can be implemented remotely while connected to the powertrain research platform through the internet, allowing easy access to the laboratory setup.     

Transport energy consumption in mountainous roads. A comparative case study for internal combustion engines and electric vehicles in Andorra

This paper analyses transport energy consumption of conventional and electric vehicles in mountainous roads. A standard round trip in Andorra has been modelled in order to characterise vehicle dynamics in hilly regions. Two conventional diesel vehicles and their electric-equivalent models have been simulated and their performances have been compared. Six scenarios have been simulated to study the effects of factors such as orography, traffic congestion and driving style. The European fuel consumption and emissions test and Artemis urban driving cycles, representative of European driving cycles, have also been included in the comparative analysis. The results show that road grade has a major impact on fuel economy, although it affects consumption in different levels depending on the technology analysed. Electric vehicles are less affected by this factor as opposed to conventional vehicles, increasing the potential energy savings in a hypothetical electrification of the car fleet. However, electric vehicle range in mountainous terrains is lower compared to that estimated by manufacturers, a fact that could adversely affect a massive adoption of electric cars in the short term.     

Projecting adoption of truck powertrain technologies and CO2 emissions in line-haul networks

In this paper we present a mixed-integer linear program to represent the decision-making process for heterogeneous fleets selecting vehicles and allocating them on freight delivery routes to minimize total cost of ownership. This formulation is implemented to project alternative powertrain technology adoption and utilization trends for a set of line-haul fleets operating on a regional network. Alternative powertrain technologies include compressed (CNG) and liquefied natural gas (LNG) engines, hybrid electric diesel, battery electric (BE), and hydrogen fuel cell (HFC). Future policies, economic factors, and availability of fueling and charging infrastructure are input assumptions to the proposed modeling framework. Powertrain technology adoption, vehicle utilization, and resulting CO₂ emissions predictions for a hypothetical, representative regional highway network are illustrated. A design of experiments (DOE) is used to quantify sensitivity of adoption outcomes to variation in vehicle performance parameters, fuel costs, economic incentives, and fueling and charging infrastructure considerations. Three mixed-adoption scenarios, including BE, HFC, and CNG vehicle market penetration, are identified by the DOE study that demonstrate the potential to reduce cumulative CO₂ emissions by more than 25% throughout the period of study.     

To save money or to save time: Intelligent routing design for plug-in hybrid electric vehicle

Electric vehicles (EVs) are promising alternative to conventional vehicles, due to their low fuel cost and low emissions. As a subset of EVs, plug-in hybrid electric vehicles (PHEVs) backup batteries with combustion engines, and thus have a longer traveling range than battery electric vehicles (BEVs). However, the energy cost of a PHEV is higher than a BEV because the gasoline price is higher than the electricity price. Hence, choosing a route with more charging opportunities may result in less fuel cost than the shortest route. Different with the traditional shortest-path and shortest-time routing methods, we propose a new routing choice with the lowest fuel cost for PHEV drivers. Existing algorithms for gasoline vehicles cannot be applied because they never considered the regenerative braking which may result in negative energy consumption on some road segments. Existing algorithms for BEVs are not competent too because PHEVs have two power sources. Thus, even if along the same route, different options of power source will lead to different energy consumption. This paper proposes a cost-optimal algorithm (COA) to deal with the challenges. The proposed algorithm is evaluated using real-world maps and data. The results show that there is a trade-off between traveling cost and time consumed when driving PHEVs. It is also observed that the average detour rate caused by COA is less than 14%. Significantly, the algorithm averagely saves more than 48% energy cost compared to the shortest-time routing.     

Comparative evaluation of eight legislated driving schedules in terms of cycle metrics and emissions from a diesel-powered turbocharged van

The present work compares, on a fundamental basis, the performance and emissions of a diesel-engined large van running on eight legislated driving cycles, namely the European NEDC, the U.S. FTP-75, HFET, US06, LA-92 and NYCC, the Japanese JC08 and the Worldwide WLTC 3-2. It aims to identify differences and similarities between various influential driving cycles valid in the world, and correlate important cycle metrics with vehicle exhaust emissions. The results derive from a computational code based on an engine mapping approach, with experimentally derived correction coefficients applied to account for transient discrepancies; the code is coupled to a comprehensive vehicle model. Soot as well as nitrogen monoxide are the examined pollutants. Only the driving cycle schedule is under investigation in this work, and not the whole test procedure, in order to identify vehicle speed (transient) effects of the individual cycles only. The recently developed WLTC 3-2 is the cycle with a very broad and at the same time dense coverage of the vehicle’s/engine’s operating activity, being thus particularly representative of ‘average’ real-world driving. Even broader is the distribution of the US06, whereas particularly thin and narrow that of the modal NEDC. It is also revealed that the more transient cycles, e.g. the NYCC or the US06, are also the ones with the highest amount of engine-out pollutant emissions and energy consumption. Relative positive acceleration and stops per km are found to correlate very well with energy and fuel consumption and all emitted pollutants.     

Mobility and environment improvement of signalized networks through Vehicle-to-Infrastructure (V2I) communications

Traffic signals, even though crucial for safe operations of busy intersections, are one of the leading causes of travel delays in urban settings, as well as the reason why billions of gallons of fuel are burned, and tons of toxic pollutants released to the atmosphere each year by idling engines. Recent advances in cellular networks and dedicated short-range communications make Vehicle-to-Infrastructure (V2I) communications a reality, as individual cars and traffic signals can now be equipped with communication and computing devices. In this paper, we first presented an integrated simulator with V2I, a car-following model and an emission model to simulate the behavior of vehicles at signalized intersections and calculate travel delays in queues, vehicle emissions, and fuel consumption. We then present a hierarchical green driving strategy based on feedback control to smooth stop-and-go traffic in signalized networks, where signals can disseminate traffic signal information and loop detector data to connected vehicles through V2I communications. In this strategy, the control variable is an individual advisory speed limit for each equipped vehicle, which is calculated from its location, signal settings, and traffic conditions. Finally, we quantify the mobility and environment improvements of the green driving strategy with respect to market penetration rates of equipped vehicles, traffic conditions, communication characteristics, location accuracy, and the car-following model itself, both in isolated and non-isolated intersections. In particular, we demonstrate savings of around 15% in travel delays and around 8% in fuel consumption and greenhouse gas emissions. Different from many existing ecodriving strategies in signalized road networks, where vehicles’ speed profiles are totally controlled, our strategy is hierarchical, since only the speed limit is provided, and vehicles still have to follow their leaders. Such a strategy is crucial for maintaining safety with mixed vehicles.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

The influence of deposit control additives on exhaust CO and HC emissions from gasoline engines (case study: Tehran)

Air pollution is the most serious environmental problem in Tehran with exhaust emissions from spark-ignition engines accounting for a major part of problem. The formation and accumulation of deposits on the internal surfaces of engines could adversely affect the exhaust emission from vehicles. It is the perception that some of fuel additives can remove these deposits due to their detergency. The Iranian Department of Environment decarbonized more that 250,000 SI engine vehicles in Tehran with the goal of reducing exhaust CO and HC emissions from gasoline engine vehicles by engine deposit removal. Here, the influence of engine deposit removal by decarbonization on the exhaust CO and HC emissions from more than 500 gasoline engine vehicles is examined. It is found that the decarbonization process could reduce the exhaust CO and HC emissions, significantly. Emissions from Peykan and Pride vehicles decreased considerably after decarbonization.     

Development a new power management strategy for power split hybrid electric vehicles

Reduction of greenhouse gas emission and fuel consumption as one of the main goals of automotive industry leading to the development hybrid vehicles. The objective of this paper is to investigate the energy management system and control strategies effect on fuel consumption, air pollution and performance of hybrid vehicles in various driving cycles. In order to simulate the hybrid vehicle, the combined feedback–feedforward architecture of the power-split hybrid electric vehicle based on Toyota Prius configuration is modeled, together with necessary dynamic features of subsystem or components in ADVISOR. Multi input fuzzy logic controller developed for energy management controller to improve the fuel economy of a power-split hybrid electric vehicle with contrast to conventional Toyota Prius Hybrid rule-based controller. Then, effects of battery’s initial state of charge, driving cycles and road grade investigated on hybrid vehicle performance to evaluate fuel consumption and pollution emissions. The simulation results represent the effectiveness and applicability of the proposed control strategy. Also, results indicate that proposed controller is reduced fuel consumption in real and modal driving cycles about 21% and 6% respectively.     

Fuel savings on a heavy vehicle via aerodynamic drag reduction

In this numerical study, the fuel-saving potentials of drag-reducing devices retrofitted on heavy vehicles are analysed. Realistic on-road operations are taken into account by simulating typical driving routes on long-haul and urban distributions; variations in vehicle weight are also considered. Results show that the performance of these aerodynamic devices depend both on their functions and how the vehicles are operated. Vehicles on long-haul routes generally save twice as much fuel as those driven in urban areas. The fuel reductions from using selected devices individually on a large truck range from less than 1% to almost 9% of the fuel cost of a vehicle doing an annual mileage is 80,000 miles.     

Exhaust emissions generated under actual operating conditions from a hybrid vehicle and an electric one fitted with a range extender

The paper describes exhaust emission tests performed on a PHEV (Plug-in Hybrid Electric Vehicle) and a BEV (Battery Electric Vehicle), in which the combustion engine was used as a range extender. The measurements of the exhaust emissions were performed for CO₂/fuel consumption, CO, THC and NO_x. The RDE measurements were performed including the engine operating parameters and emissions analysis. This analysis shows that the engines of BEVs and PHEVs operate in a different parameter range when under actual operating conditions, which directly translates into the exhaust emission values. This is particularly the case for the emission of NO_x. The investigations were carried out for two routes differentiated by the length and share of the urban and extra-urban cycles. For both routes, the emission of THC and CO were lower for the PHEV engine – HC by 69% (22 mg/km, route 1) and 6% (15 mg/km, route 2), CO by 69% (0.12 mg/km, route 1) and 80% (0.1 mg/km, route 2). For route 1, characterized by a greater share of the urban cycle, the emission of NO_x was lower by 70% (2 mg/km) for the BEV engine, and (route 2) lower by 60% (8 mg/km) for the PHEV engine. Additionally, the curves of the exhaust emissions in time for individual exhaust components have been presented that indicate that in the motorway cycle the emission of THC and CO from the BEV vehicle increases significantly up to ten times compared to urban cycle.     

A comparison of technologies for carbon-neutral passenger transport

In this study, the use of energy carriers based on renewable energy sources in battery-powered electric vehicles (BPEVs), fuel-cell electric vehicles (FCEVs), hybrid electric vehicles (HEVs) and internal combustion engine vehicles (ICEVs) is compared regarding energy efficiency, emission and cost. There is the potential to double the primary energy compared with the current level by utilising vehicles with electric drivetrains. There is also major potential to increase the efficiency of conventional ICEVs. The energy and environmental cost of using a passenger car can be reduced by 50% solely by using improved ICEVs instead of ICEVs with current technical standard. All the studied vehicles with alternative powertrains (HEVs, FCEVs, and BPEVs) would have lower energy and environmental costs than the ICEV. The HEVs, FCEVs and BPEVs have, however, higher costs than the future methanol-fuelled ICEV, if the vehicle cost is added to the energy and environmental costs, even if significant cost reductions for key technologies such as fuel cells, batteries and fuel storages are assumed. The high-energy efficiency and low emissions of these vehicles cannot compensate for the high vehicle cost. The study indicates, however, that energy-efficiency improvements, combined with the use of renewable energy, would reduce the cost of CO₂ reduction by 40% compared with a strategy based on fuel substitution only.     

Analysis of real driving gaseous emissions from light-duty diesel vehicles

Increasingly strict emissions standards are providing a major impetus to vehicle manufactures for developing advanced powertrain and after-treatment systems that can significantly reduce real driving emissions. The knowledge of the gaseous emissions from diesel engines under steady-state operation and under transient operation provides substantial information to analyze real driving emissions of diesel vehicles. While there are noteworthy advances in the assessment of road vehicle emissions from real driving and laboratory measurements, detailed information on real driving gaseous emissions are required in order to predict effectively the real-time gaseous emissions from a diesel vehicle under realistic driving conditions. In this work, experiments were performed to characterize the behavior of NOx, unburned HC, CO, and CO₂ emitted from light-duty diesel vehicles that comply with Euro 6 emissions standards. The driving route fully reflected various real-world driving conditions such as urban, rural, and highway. The real-time emission measurements were conducted with a Portable Emissions Measurement System (PEMS) including a Global Positioning System (GPS). To investigate the gaseous emission characteristics, authors determined the road load coefficients of vehicle specific power (VSP) and regression coefficient between fuel use rate and VSP. Furthermore, this work revealed the correlation between the rates of average fuel use and each gaseous emission.     

Cutting vehicle emissions with regenerative braking

This paper presents an analysis of vehicle regenerative braking systems as a quick and relatively easy means of achieving higher overall fuel efficiency and lowering carbon emissions. The system involves the installation of an additional electric motor/generator in parallel to the vehicle’s internal combustion engine and is used in conjunction with a DCDC converter and ultracapacitor. The system is used to recapture the energy lost in vehicle braking, significantly reducing a vehicle’s overall energy consumption and lowering vehicle emissions. Experimentally-based evidence is collected and compared for two sample vehicles to deduce the potential fuel and emissions saving.     

Investigation of tailpipe and evaporative emissions from China IV and Tier 2 passenger vehicles with different gasolines

The limited understanding of vehicular emissions in China, especially evaporative emissions, is one obstacle to establishing tighter standards. To evaluate tailpipe and evaporative emissions, two typical China IV vehicles and one Tier 2 vehicle with an onboard refuelling vapour recovery (ORVR) system were selected and tested. One of the China IV vehicles was fuelled with gasoline, E10 and M15, respectively, to investigate the effect of fuel properties on vehicular emissions. For each vehicle, cold-start tailpipe emission tests were conducted first, followed by an evaporation test. Based on the emission factors and real-world vehicle activity data, the annual tailpipe and evaporative hydrocarbon (HC) emissions of each vehicle were calculated and compared. The results show that E10 and M15 significantly reduced the tailpipe CO and particle number (PN) emissions but seriously aggravated the NOx emissions, especially for M15. The hot soak losses (HSLs) and diurnal breathing losses (DBLs) were slightly impacted by the fuel properties. The annual evaporative emissions with E10 and M15 were higher than that with gasoline. The ORVR system effectively controlled the evaporative emissions, especially for DBLs. Evaporative emissions from the China IV vehicles were 1.1–1.4 times the tailpipe HC emissions. Additionally, the evaporative emission factors of the China IV vehicles were almost 50% lower than the standard (2.0 g/test), whereas their annual evaporative emissions were almost 1.8–2.8 times higher than those from the Tier 2 vehicle. Therefore, controlling evaporative emissions currently remains a great need in China, and the ORVR might be a recommended evaporative control technology.     

Modeling the effect of electric vehicle adoption on pedestrian traffic safety: An agent-based approach

When operated at low speeds, electric and hybrid vehicles have created pedestrian safety concerns in congested areas of various city centers, because these vehicles have relatively silent engines compared to those of internal combustion engine vehicles, resulting in safety issues for pedestrians and cyclists due to the lack of engine noise to warn them of an oncoming electric or hybrid vehicle. However, the driver behavior characteristics have also been considered in many studies, and the high end-prices of electric vehicles indicate that electric vehicle drivers tend to have a higher prosperity index and are more likely to receive a better education, making them more alert while driving and more likely to obey traffic rules. In this paper, the positive and negative factors associated with electric vehicle adoption and the subsequent effects on pedestrian traffic safety are investigated using an agent-based modeling approach, in which a traffic micro-simulation of a real intersection is simulated in 3D using AnyLogic software. First, the interacting agents and dynamic parameters are defined in the agent-based model. Next, a 3D intersection environment is created to integrate the agent-based model into a visual simulation, where the simulation records the number of near-crashes occurring in certain pedestrian crossings throughout the virtual time duration of a year. A sensitivity analysis is also carried out with 9000 subsequent simulations performed in a supercomputer to account for the variation in dynamic parameters (ambient sound level, vehicle sound level, and ambient illumination). According to the analysis, electric vehicles have a 30% higher pedestrian traffic safety risk than internal combustion engine vehicles under high ambient sound levels. At low ambient sound levels, however, electric vehicles have only a 10% higher safety risk for pedestrians. Low levels of ambient illumination also increase the number of pedestrians involved in near-crashes for both electric vehicles and combustion engine vehicles.     

Fuel economy of hybrid-electric versus conventional gasoline vehicles in real-world conditions: A case study of cold cities in Quebec,Canada

This paper investigates the fuel efficiency of commercial hybrid electric vehicles (HEVs) and compares their performance with respect to standard gasoline vehicles in the context of cold Canadian urban environments. The effect of different factors on fuel efficiency is studied including road driving conditions (link type, city size), temperature, speed, cold-starts and eco-driving training. For this study, fuel consumption data at the link level in real-world conditions was used from a sample of 74 instrumented vehicles. From the study fleet, 21 vehicles were HEVs. Among other results, the beneficial fuel efficiency merits of hybrid vehicles were demonstrated with respect to gasoline cars, in particular at low speeds and in urban (city) environments. After controlling for other factors, sedan HEVs were 28% more efficient than sedan gasoline vehicles. However, the low temperatures (below 0 °C) observed regularly during winter season in the study cities were identified as a detrimental factor to fuel economy. In winter, the fuel efficiency of HEVs decrease about 20% with respect to summer. Other factors such as eco-driving training, city size, cold start and vehicle type were also found to be statistically significant.     

Does winter road maintenance help reduce air emissions and fuel consumption?

Winter road maintenance (WRM) has been shown to have significant benefits of improving road safety and reducing traffic delay caused by adverse weather conditions. It has also been suggested that WRM is also beneficial in terms of reducing vehicular air emissions and fuel consumptions because snow and ice on road surface often cause the drivers to reduce their vehicle speeds or to switch to high gears, thus decreasing fuel combustion efficiency. However, there has been very limited information about the underlying relationship, which is important for quantifying this particular benefit of a winter road maintenance program. This research is focused on establishing a quantitative relationship between winter road surface conditions and vehicular air emissions. Speed distribution models are developed for the selected Ontario highways using data from 22 road sites across the province of Ontario, Canada. The vehicular air emissions under different road surface conditions are calculated by coupling the speed models with the engine emission models integrated in the emission estimation model - MOVES. It was found that, on the average, a 10% improvement in road surface conditions could result in approximately 0.6–2% reduction in air emissions. Application of the proposed methodology is demonstrated through a case study to analyse the air emission and energy consumption effects under specific weather events.     

Fuel economy improvements for urban driving: Hybrid vs. intelligent vehicles

The quest for more fuel-efficient vehicles is being driven by the increasing price of oil. Hybrid electric powertrains have established a presence in the marketplace primarily based on the promise of fuel savings through the use of an electric motor in place of the internal combustion engine during different stages of driving. However, these fuel savings associated with hybrid vehicle operation come at the tradeoff of a significantly increased initial vehicle cost due to the increased complexity of the powertrain. On the other hand, telematics-enabled vehicles may use a relatively cheap sensor network to develop information about the traffic environment in which they are operating, and subsequently adjust their drive cycle to improve fuel economy based on this information – thereby representing ‘intelligent’ use of existing powertrain technology to reduce fuel consumption. In this paper, hybrid and intelligent technologies using different amounts of traffic flow information are compared in terms of fuel economy over common urban drive cycles. In order to develop a fair comparison between the technologies, an optimal (for urban driving) hybrid vehicle that matches the performance characteristics of the baseline intelligent vehicle is used. The fuel economy of the optimal hybrid is found to have an average of 20% improvement relative to the baseline vehicle across three different urban drive cycles. Feedforward information about traffic flow supplied by telematics capability is then used to develop alternative driving cycles firstly under the assumption there are no constraints on the intelligent vehicle’s path, and then taking into account in the presence of ‘un-intelligent’ vehicles on the road. It is observed that with telematic capability, the fuel economy improvements equal that achievable with a hybrid configuration with as little as 7 s traffic look-ahead capability, and can be as great as 33% improvement relative to the un-intelligent baseline drivetrain. As a final investigation, the two technologies are combined and the potential for using feedforward information from a sensor network with a hybrid drivetrain is discussed.