轴力作用下X型焊接管节点热点应力的分布规律

海洋平台中的焊接管节点的疲劳寿命是由热点应力的大小和分布决定。热点应力的大小决定了管节点在疲劳失效前所能承受的循环荷载的次数,而热点应力的位置则决定了疲劳裂纹的萌生位置和扩展方式。文中采用有限元方法分析了承受轴向拉力作用的X型焊接管节点在焊缝周围的热点应力的分布情况,通过对112个X节点进行的模型分析,研究了节点几何参数对热点应力大小和分布规律的影响。     

一种新的海洋平台管节点应力评估方法

海洋工程焊接管节点受应力集中及复杂随机载荷的联合作用,容易发生疲劳破坏。为了提高焊接管节点结构疲劳寿命预测的准确性,文章以管壁厚方向上的一点作为疲劳评估点,提出了一种新的管节点结构应力计算方法。通过与国际上公开发表的疲劳试验数据进行比较,证明了文中方法应用于管节点结构的可行性及考虑壁厚方向应力梯度的有效性。基于数值计算,文中还提出了可用于T型管节点应力集中系数计算的参数公式,并对参数公式的精度进行了验证。     

轴力作用下T节点焊缝周围的平均应力分布

平均应力模型法是评价海洋平台中管节点疲劳寿命的一种方法,这种方法认为节点的疲劳寿命是由热点应力幅值和焊缝周围的应力分布确定的。管节点焊缝周围应力分布通过一个平均应力分布参数AVS描述。本文研究了轴力作用下T节点的AVS大小,通过对127个不同几何参数的T节点模型的计算,调查了几何参数对AVS的影响,提出了用于计算AVS的参数方程,从而完善了传统的平均应力模型,为轴力作用下T节点的疲劳寿命计算提供了一种快速而高效的方法。     

Geometric stress distribution along the weld toe of the outer brace in two-planar tubular DKT-joints: Parametric study and deriving the SCF design equations

Regarding the research efforts expended so far on the calculation of stress concentration factors (SCFs) in tubular joints, two major shortcomings can be noted: (a) significant effort has been devoted to the study of SCFs in various uni-planar connections. Nevertheless, for multi-planar joints which cover the majority of practical applications, very few investigations have been reported due to the complexity and high cost involved; (b) majority of these research works focused on the study of SCFs at certain positions such as the saddle, crown toe, and crown heel, and they have ignored the hot-spot stress (HSS) at other positions along the weld toe. In the present paper, effects of dimensionless geometrical parameters on the SCF distribution along the weld toe of main (outer) braces in the axially loaded right-angle two-planar tubular DKT-joints are investigated. In order to study the multi-planar effect, SCF distribution in two-planar joints is compared with the distribution in a uni-planar joint having the same geometrical properties. A complete set of SCF database is constructed based on the two-planar DKT-joint Finite element models which are verified against experimental results and the predictions of Lloyd’s Register (LR) equations. The FE models cover a wide range of geometrical parameters. Six new SCF parametric formulae are developed through nonlinear regression analyses for the accurate and reliable fatigue design of two-planar DKT-joints under axial loads. An assessment study of these equations is conducted against the experimental data, the original FEM database and the acceptance criteria recommended by the UK Department of Energy.     

双平面焊接圆管截面DKT节点的中心撑杆鞍点及冠点位置的应力集中系数(英文)

A set of parametric stress analyses was carried out for two-planar tubular DKT-joints under different axial loading conditions.The analysis results were used to present general remarks on the effects of the geometrical parameters on stress concentration factors(SCFs) at the inner saddle,outer saddle,and crown positions on the central brace.Based on results of finite element(FE) analysis and through nonlinear regression analysis,a new set of SCF parametric equations was established for fatigue design purposes.An assessment study of equations was conducted against the experimental data and original SCF database.The satisfaction of acceptance criteria proposed by the UK Department of Energy(UK DoE) was also checked.Results of parametric study showed that highly remarkable differences exist between the SCF values in a multi-planar DKT-joint and the corresponding SCFs in an equivalent uni-planar KT-joint having the same geometrical properties.It can be clearly concluded from this observation that using the equations proposed for uni-planar KT-connections to compute the SCFs in multi-planar DKT-joints will lead to either considerably under-predicting or over-predicting results.Hence,it is necessary to develop SCF formulae specially designed for multi-planar DKT-joints.Good results of equation assessment according to UK DoE acceptance criteria,high values of correlation coefficients,and the satisfactory agreement between the predictions of the proposed equations and the experimental data guarantee the accuracy of the equations.Therefore,the developed equations can be reliably used for fatigue design of offshore structures.     

T型接头焊趾表面裂纹应力强度因子的简化计算方法

T型接头是船舶与海洋结构物的典型结构形式之一,其焊趾处常常是疲劳热点区域。T型接头焊趾表面裂纹的应力强度因子是船舶与海洋结构的、基于断裂力学安全评定和疲劳寿命预测的基础。本文对T型接头表面裂纹应力强度因子的计算方法,尤其是Bow ness等人提出的T型接头焊趾表面裂纹应力强度因子的计算公式进行了分析,在此基础上导出了形式简单,物理意义明确的T型接头焊趾表面裂纹应力强度因子的简化计算公式,并和相关的应力强度因子的计算结果进行了比较,证明了本文简化方法的可行性。     

主管受拉K型管节点抗冲击性能有限元研究

偶然荷载引起的撞击会造成海洋平台中的管桁架严重损伤,尤其是管节点的破坏,严重时会导致整个平台的损坏,因此管节点是海洋平台设计研究中的一个重要内容.本文以海洋平台中常见的K型管节点为研究对象,利用有限元软件ABAQUS研究了3个主管在受拉状态下的K型管节点的抗冲击性能.在研究过程中以几何参数和荷载参数为主要变量,分析了各相关参数对管节点的抗冲击性能的影响.确定了K型管节点在冲击荷载作用下的破坏模态.在对冲击力、位移、能量耗散等时程曲线的分析中揭示了抗冲击性能工作机理.研究结果表明:支主管的径厚比以及支管的拉压状态对管节点所受到的最大冲击力和节点变形具有较显著的影响.     

轴向载荷下多平面DT型管节点应力集中系数概率模型研究

应力集中系数作为一个随机变量,对管节点及导管架平台的疲劳可靠性评估结果有着重要影响。文章以多平面DT型管节点为研究对象,建立了352个几何参数不同的三维管节点有限元模型,并分析了沿弦管-撑管焊缝处的应力集中系数分布。采用密度直方图描述最大应力集中系数统计样本的特征,利用疲劳可靠性分析中常用的几种概率分布进行拟合。各个概率模型中的参数通过极大似然估计方法得到。根据卡方检验的结果对比发现,Birnbaum-Saunders分布是最适合的概率模型。因此,文中提出一组适用于描述在轴向载荷即单向轴向和平衡轴向载荷作用下多平面DT型管节点弦管侧和撑管侧最大应力集中系数分布的概率模型,对今后导管架式海洋平台结构的疲劳可靠性分析具有重要意义。     

海上平台管节点疲劳性能研究

在研究D500系列管节点疲劳特性的基础上，吸取国内外研究成果，建立了适用较广的可靠的管节点疲劳寿命计算方法．文章给出了建立在大量数据基础上的S－N曲线，探讨了影响疲劳寿命的因素，进行了局部应力—应变法及断裂力学法计算分析，对海洋平台管节点提出了适用于工程实际的建议．     

Study on hot spot stress distribution of three-planar tubular Y-joints subjected to in-plane bending moment

The three-planar tubular Y-joint (3Y-joint) is the main part of the fatigue assessment of tripod substructures of offshore wind turbines (OWTs). As typical multiplanar tubular joints, 3Y-joints are affected a lot by multiplanar interaction between braces. Moreover, the locations of hot spot stress (HSS) can vary considerably under different load types. Thus, the distributions of stress concentration factor (SCF) and multiplanar interaction factor (MIF) along weld toe curves are necessary to calculate HSS. Considering these requirements, this study focuses on the 3Y-joint considering the wide application of the tripod substructure of OWT. A finite element (FE) analysis method is introduced and validated. Then, a numerical database is established covering common ranges of parameters used in practice. The SCF and MIF of 3Y-joint under in-plane bending moment are analyzed. Distribution formulas are proposed and proved suitable for calculating HSS in engineering design.     

船舶折角型节点的疲劳裂纹扩展计算

文章以船舶折角型节点为研究对象,运用有限元软件WALCS和PATRAN分别预报某船的水动力响应和结构热点应力响应.为避免计算表面裂纹应力强度因子时需要在PATRAN有限元模型中疲劳热点区域采用体单元建模,文中提出了一种计算波浪载荷下船海结构物三维表面裂纹应力强度因子而无需在PATRAN中建立体模型的方法,并通过与广泛认可的经验公式对比验证其精度.将此方法应用于该船船舯底边舱折角处表面裂纹应力强度因子计算,计算并总结出波浪载荷下该类节点处表面裂纹应力强度因子的无量纲计算经验公式.应用一种基于谱分析构建结构疲劳载荷谱的方法,结合单一曲线模型对该节点进行裂纹扩展计算.计算结果表明:该船船舯底边舱折角疲劳寿命不满足设计要求,建议对节点进行改进.     

基于CSR中热点应力的散货船疲劳强度分析

基于散货船共同结构规范（CSRBC）的热点应力法,对一艘30000t级散货船内底板与底凳的斜板相交处进行了疲劳强度分析。通过对疲劳热点位置建立精细网格模型,采用中国船级社开发的软件CCS-Tools及英国劳氏船级社开发的SHIPRIGHT进行了热点应力分析及疲劳寿命计算。另外,还介绍了采用电子表格计算疲劳寿命的方法。     

The effect of weld residual stress on fracture toughness at the intersection of two welding lines of offshore tubular structure

Due to the spatial complexity and fabrication characteristics of offshore platforms, it is inevitable to encounter overlaps or proximity of weld lines in tubular joints. Several international standards such as American Petroleum Institute (API), American Welding Society (AWS), and American Institute of Steel Construction (AISC) regulate the minimum distance between primary weld beads; however, any logical and detailed background of this limitation has not been presented. For a non-compliant weld joint where the regulation is not met, fracture toughness calculation is a typical index to verify the structural integrity.This research consists of two parts. First, weld residual stress distributions are calculated by a 3D thermo-mechanical nonlinear Finite Element Analysis. Two crossing welds, a T-weld crossing on a butt weld, are simulated in one model. A separate tee and a butt welding simulations are also performed for a comparative purpose. Second, SIFs and J-integral values are calculated at the surface and deepest crack tip locations for four different types of semi-elliptical surface cracks. Four cracks are embedded into the weld model and the residual stress distribution from the 3D thermo-mechanical FEA are mapped to a 3D FE crack model as initial conditions. An additional axial tensile load is also imposed. SIF values are compared with those using the weighting function method for the butt weld model subject to three load cases, i.e., tensile stress only, weld residual stress only, and both of them. From the simulation, a tubular joint containing a chord girth weld intersected with weld beads of brace is found to show lower the SIF values than that having only a girth weld on chord.     

等效热点应力法结合临界面法评估焊接接头多轴疲劳强度研究

基于焊缝本身引起的非线性分布应力自平衡的性质,在板厚方向应力峰值零点位置定义等效热点应力,结合基于临界面法的MWCM法建立评估复杂焊接接头多轴疲劳强度的方法。采用数值计算分析零点位置的变化规律,建立零点位置拟合方程。利用公开发表的试验数据以及现有的热点应力法有限元计算结果对等效热点应力法进行精度验证。结果表明,等效热点应力法和现有的热点应力法具有很好的一致性,能在一定程度上考虑厚度效应对疲劳强度的影响,可以评估多轴疲劳强度。     

SCF equations in multi-planar welded tubular DT-joints including bending effects

Welded tubular connections exhibit significant stress concentrations at the weld vicinity, which may result in fatigue failure. Stress concentration factors (SCFs) in DT-joint are computed, based on an extensive finite element study. The present paper develops a methodology for the calculation of the maximum local stress, referred to as “hot-spot stress”, in a multi-planar DT-joint, with particular emphasis on the effects of bending moments on the braces and the chord. Special attention is focussed on the location where critical stress concentration occurs, as well as on the so-called “carry-over phenomenon” and its implications on the hot-spot stress value. Simplified design equations for fatigue design are proposed to determine SCF values due to bending in order to improve predictions with respect to existing design tools.     

Stress concentration factors of multi-planar tubular KT-joints subjected to in-plane bending moments

Numerical research on the stress concentration factors (SCFs) in uniplanar tubular joints is abundantly reported in literature. However, it has been shown that SCF equations for uniplanar joints can lead to both under- or overestimation of the SCFs in multi-planar joints. In this paper, a parametric finite element study of 81 different three-planar KT joints subjected to five different in-plane bending loading conditions is performed. The effects of different non-dimensional geometrical parameters on the SCF values at the crown locations of the central and outer braces are studied. Based on nonlinear regression analyses of the finite element results, a new set of SCF equations is developed and presented.     

Fatigue resistance of welded steel tubular X-joints

High-cycle fatigue experiments are performed on welded tubular steel X-joints, with braces and chord of equal diameter. They are scaled-down joints, used extensively in offshore wind platforms. Three different welding procedures are considered in specimen fabrication: manual, fully-automatic and manual with HFMI post-weld treatment. Τwo possible locations for crack initiation were identified: chord “crown” and “in-between location”, also verified by numerical calculations and fractography of failed specimens. Monotonic loading tests on fatigue-cracked specimens showed good performance in terms of ultimate strength and deformation capacity, despite the presence of through-thickness cracks. The results are compared with predictions from relevant design standards.     

肘板趾端表面裂纹在随机波浪载荷作用下的疲劳扩展预报

肘板趾端是船舶与海洋结构的疲劳热点。文章用三维有限元分析了趾端表面裂纹应力强度因子修正系数的变化规律,并与BS7910推荐的典型节点表面裂纹应力强度因子公式计算结果作了对比,结果表明趾端表面裂纹应力强度因子沿深度方向的放大系数和T型节点相差很小,而表面端点应力强度因子修正系数则当裂纹长度在肘板厚度范围内时和T型节点相差很小,超出后则相差较大。以某客滚船上肘板趾端应力范围长期分布服从Weibull分布,产生系列均值为零的应力幅,应力强度因子分别采用有限元结果和BS7910中T型接头公式进行计算,采用单一曲线模型计算该趾端表面裂纹的裂纹扩展。计算等效应力强度因子幅时,考虑焊接残余应力的影响。计算结果表明以T型接头的公式计算趾端表面裂纹应力强度因子和有限元结果相差很小。建议将T型节点表面裂纹应力强度因子计算公式用于趾端表面裂纹应力强度因子的计算,并采用单一曲线模型对随机波浪载荷下作用下船舶典型节点疲劳裂纹的扩展寿命进行了预报。     

海洋平台结构系统疲劳可靠性分析方法

本文研究了海洋平台结构系统疲劳可靠性评估方法。文中对平台结构简生管节点疲劳可靠性分析模型进行了简单的评述，在该模型的基础上，建立了用S－N曲线模型与断裂力学模型分别计算平台完好管节点及有初始裂纹管节点疲劳寿命的平告结构系统疲劳可靠性分析模型。作为一个算例，文中运用作者开发的程序系统，对一固定式导管架平台进行了疲劳可靠性计算。     

船舶舷侧细节结构的热点应力计算中的不确定性因素研究

疲劳是船舶结构一种重要的失效模式。在过去的十多年间，涌现出了一些不同的疲劳强度的评估方法，其中S－N曲线法在船级社中得到了广泛的应用。但是，仅就S－N曲线法中的热点应力法而言，不同的组织和个人所预报的疲劳寿命通常也存在很大差异，而计算所得的热点应力集中系数的不同是产生这些差异的一个重要影响因素。本文运用有限元比较研究的方法，对某船舶舷侧细节结构的热点应力计算中可能存在的不确定因素进行了综合分析。通过采用不同的单元类型，不同的建模方法以及不同的有限元软件ABAQUS和ANSYS，得出了相关结论，为正确计算此类船舶结构细节的热点应力提供了指导。