共查询到20条相似文献,搜索用时 78 毫秒
1.
2.
3.
为减轻水密门的质量,提高安全性和经济性,对水密门进行轻量化设计。通过对比国内外现状,提出水密门轻量化的技术指标,并进行方案设计。通过关键技术的实施,完成样机的研制工作。试验结果表明:样机性能良好,符合技术指标的要求。研究成果可为水密门的轻量化设计提供一定参考。 相似文献
4.
国外海军舰船水密门的应用与发展 总被引:1,自引:0,他引:1
《舰船科学技术》2015,(12):175-179
水密门是维持舰船水密性的重要船体属具之一,一直以来倍受各国海军的关注和重视。近年来,新材料、新技术的发展推动了各国海军舰船水密门的升级换代。本文对国外海军舰船水密门的应用和发展进行深入分析研究,并以标准压力作动门为例,详细介绍了美国海军新型舰船水密门的研制、质量认证试验等情况,最后对舰船水密门的发展进行展望。 相似文献
5.
自1974年国际海上人命安全公约(以下简称"公约")生效以来,船用水密门和防火门作为保障船员生命安全的手段,成为海船上一项必不可少的重要配件.随着海洋货运船舶和大型舰艇的设计能力逐步提高,对大型船用防火水密门的设计也提出了更高要求.针对大型船舶设计一种具备高通过性的L型船用低门槛A-60级防火水密门,并对门页结构进行有限元分析,对大型防火水密门的设计提供一定参考. 相似文献
6.
为更好地控制集装箱滚装船门框结构的安装精度,以45000t集装箱滚装船中只包含水密门结构的分段为例进行水密门精度控制研究。通过研究该分段的建造方式,改进分段的建造工艺,合理安排门框结构在分段建造过程中的安装顺序,进而缩减结构变形;同时,利用精度测量仪器进行跟踪测量,保证始终把精度控制在有效范围内。对焊接过程中采用的焊接方法进行研究,改进焊接工艺,采取逐步退焊法控制焊接热量,进而减少焊接变形。通过对分段水密门门框结构的安装工艺及焊接工艺进行研究,将理论与实践相结合,总结出一套行之有效的建造工艺,确保分段门框结构安装精度得到有效控制,保证水密门的性能,为该系列船后续的分段建造提供参考。 相似文献
7.
8.
美国海岸警卫队(USCG)12月8日发布了水密门安全警报,强调了适当维护和关闭水密门的重要性。在过去的两年里,USCG曾发布过两项类似的安全警报。这与不当使用和维护水密门造成的持续海难事故有直接关系。如果正确使用水密门,超过42%的渔船海难事故是可以避免或者减少损失的。针对此类事故,USCG对船东和船舶提出三项建议:一、定期检查船舶所有水密门的状况; 相似文献
9.
介绍目前国内外型尺寸最大、手动陆用耐压水密门的研制及应用,严密地剖析水密门研制和使用中的关键点,阐述操作使用和日常维护。 相似文献
10.
雷海 《中国远洋航务公告》2011,(2):62-64
四、安全对策
1.装货前
(1)检查船舶设备,尤其是老龄船必须做到适货,适航。清洁污水沟(井),保持畅通,并在污水井盖上铺妥麻袋皮;检查舱内各种管系,如发现漏孔,应及时补妥,并保持良好的工作状态;检查各舱盖、水密门、测量管、空气管帽,双层底和边水柜,保持良好的水密状态,如发现欠妥,应临时用封舱贴条封死,或用水泥封舱;认真检查货舱和压载水舱强度构件,尤其适肋骨纵衍、肘板、横隔板强度。 相似文献
11.
介绍了我国港口资源的整合现状,指出港口整合可以提升港口的形象和地位,也为区域经济和城市的发展注入强大的动力。最后指出在港口资源整合中要避免的几个问题。 相似文献
12.
13.
广州集装箱码头的轮胎式场桥小车制动器使用10多年后,出现了许多问题,故进行了改造.分析了轮胎式集装箱龙门起重机小车制动器的主要故障现象,提出了改造方案,并加以实施. 相似文献
14.
本文对现有的选定球面轴承的三种工程方法进行了分析比较.引入了“合力系数”,并给出了合力方向上投影面积的精确解. 相似文献
15.
16.
17.
18.
分析柴油机故障中常见的机体裂纹故障原因,认为由于设计缺陷和管理及操作不当,易造成船舶柴油机缸体上的裂纹多发生在气缸套凸肩处。如不及时处理这些裂纹和故障,就会造成缸套的裂纹直至出现缸套漏水等严重后果,针对NANTAIQUEEN轮柴油机对该类型故障的检修提出具体措施。 相似文献
19.
The hydrophysical and hydrochemical structure of the Sea of Azov, with developed bottom anoxia, was studied during the RV “Akvanavt” cruise from July 31 to August 03, 2001. The anoxic zone with a thickness from 0.5 to 4 m above the bottom was found in all deep regions of the Sea. Concentrations of hydrochemical parameters were similar to the pronounced anoxic conditions (about 90 mmol m− 3 of hydrogen sulfide, 17 mmol m− 3 of ammonia, 6 mmol m− 3 of phosphate, 7 mmol m− 3 of total manganese). The hydrophysical structure was characterized by the uniform distribution of temperature in the upper 6–7 m mixed layer (UML). Below this a thin (0.4–0.8 m) thermocline layer was observed, just above the anoxic waters. Formation of this phenomenon was connected with that summer weather conditions. Intensive rains led to increased influx of river waters in June. That resulted in large input of allochtonous organic matter (OM) and inorganic nutrients; the latter were consumed on the additional autochthonous organic matter production. In July the weather was characterized by a significant rise in the daily averaged air temperature and large oscillations of temperature during the day. In this period a wind of constant direction was absent, but wind bursts were observed. The completed analyses showed that the formation of such a structure could be connected with the following factors: (i) positive growth trends of the daily averaged temperature and the daily oscillations of temperature, (ii) presence of wind bursts. The joint action of these factors resulted in the formation of the UML. The amplitude of wind bursts determined the depth of UML, and the value of trend determined the value of the temperature change in the thermocline. An initial presence of bottom halocline (caused by the Black Sea water influx to the bottom of the Sea of Azov) prevented the heating of the bottom layer and therefore led to an increase of vertical gradient of temperature in the thermocline. The spatial distribution of the turbulent exchange coefficient confirmed the existence of a “stagnation” area located above the anoxia zone, which is also, apparently, the reason for its occurrence. 相似文献
20.