共查询到19条相似文献,搜索用时 171 毫秒
1.
为了提高船舶尾部模态计算的精度,文章提出了一种尾部详细结构与船体骨架结合的简化有限元模型,应用该模型对某全回转推进船舶尾部模态进行了计算,并将其结果与另外两种传统简化模型(即尾部三维模型与尾部+一维梁混合模型)的计算结果进行了比较。研究发现改进模型与传统模型在尾部局部模态计算中没有明显差别,但对整体模态而言其差异随频率增大而增大。为了进一步验证模型的有效性,在航行过程中对该船舶振动情况进行了测试,并利用运行模态分析法识别尾部整体模态。通过识别结果与计算结果的比较可见,三种模型在基频(1阶弯曲)计算时误差均很小,但是在高阶固有频率计算中改进的模型误差明显小于另两种模型。 相似文献
2.
3.
4.
针对升船机卷筒体工况及结构特点,提出模态、屈曲建模及校验的卷筒结构稳定性研究路线。首先以经验参照法分析卷筒结构的稳定性指标,引出与工程实际的矛盾,进而基于有限元法校验多工况卷筒的刚度强度;其次以整体模态理论、屈曲分析理论为依据,推导出模态分析、屈曲分析的数学模型;最后基于有限元法开展卷筒结构的整体模态运算分析,采用外载荷单位化的施加方法,开展卷筒结构的有限元特征值屈曲运算分析。校验出升船机卷筒结构的设计参数满足工程稳定性要求。 相似文献
5.
6.
针对采用吊舱推进器的邮轮建立4种尺度的有限元模型,各尺度模型均包含2种类型:A类以质量点模拟吊舱推进器,B类建立吊舱推进器的三维有限元模型。分别对两类有限元模型进行模态分析,通过比较固有频率来分析吊舱推进器与主船体的振动耦合效应。通过振动模态对比,确定结构动力学计算的最佳模型尺度范围,并在此基础上进行推进器舱振动响应分析。结果表明,在模型较大时,吊舱推进器对结构扭转振动耦合影响最大,而在计算模型范围较小时,其对水平振动耦合影响最大;垂向速度响应的最大值并没有出现在激励力正上方,而是位于2个吊舱推进器之间的船中区域。本文结论可为船体尾部振动优化分析与邮轮设计提供参考。 相似文献
7.
舰船的机械结构振动不仅会产生噪声,降低舰船的隐蔽性,还会导致机械结构由于振动造成的破坏,因此,研究船舶机械结构的振动特性具有重要的意义。船舶尾部是动力系统所在地,研究船舶尾部的振动传递特性,并针对振动传递特性进行相应的减振设计对于改善船舶整体的性能有良好的效果。本文首先介绍振动功率流理论和无阻尼自由振动理论,并结合有限元分析技术,对船舶尾部的振动传递特性进行仿真。 相似文献
8.
船舶结构振动特性研究 总被引:17,自引:1,他引:16
本文利用SHELL63、BEAM4、SOLID95、COMBIN14四种类型共64187个有限单元和30种几何参数建立了接近于真实船舶(包括机舱动力设备)的有限元模型。在考虑流一固耦合状态下,用有限元技术对船舶进行模态分析以及船舶对激励力的振动响应数值计算。在模态分析过程中,采用了矩阵缩减的方法来消除局部模态,以便获得整体弯曲和扭转振动模态。然后对主机单层隔振器和辅机双层隔振器的减振效果进行了预估。将建立的接近于真实船舶的有限元模型和尾部结构的三维有限元和梁组合模型的数值计算结果进行比较,得到一些重要结论。本文为船舶设计人员在船舶设计阶段,预报船舶结构振动提供了一条新的途径。 相似文献
9.
10.
《舰船科学技术》2015,(12):13-17
螺旋桨轴系激励作用下水下航行器的尾部结构会产生低频辐射噪声,针对尾部结构的声振特性开展研究很有必要。本文以水下加肋圆柱壳为对象,采用有限元耦合声学边界元计算了加肋圆柱壳的辐射声功率,针对尾部噪声分析的3种模型:整体三维模型,尾部三维模型+首部梁模型的混合模型,尾部截断模型,分析讨论3种不同模型处理方法对声辐射特性的影响。结果表明采用尾部截断模型计算辐射声功率时在低频段与整体三维模型的误差较大,混合模型在趋势上与整体三维模型吻合较好。对比尾端部不同方向激励力对环肋圆柱壳声辐射特性的影响,结果表明横向和垂向激励对环肋圆柱壳的辐射声功率没有影响,但是对远场声压指向性有较大影响。 相似文献
11.
12.
该文采用有限元方法对某型多用途拖船尾滚筒的结构强度及稳定性进行了分析及计算,尝试利用了积分加载的方式施加结构的外载荷,分两种不同的工况对结构的主要参数进行了具体分析和比较,计算结果及经验分析验证了该外载荷施加方式的正确性,为尾滚筒的结构强度设计及稳定性分析工作提供了一定的参考。 相似文献
13.
14.
45000t集装箱滚装船艉门是艉部大开口密封设备,由艉门主体和滚装翼板组成,艉门主体对整个滚装区域与外部空间进行水密分隔,滚装翼板作为艉跳板与滚装通道衔接。滚装翼板在工作状态下搭在艉跳板上,保证车辆顺利进入滚装货舱;通道关闭时,先收拢滚装翼板,再关闭艉门,确保艉门周围的水密结构正常,保证通道的水密性。主要对艉门主体、滚装翼板及其相关部件的安装进行研究,阐述艉门主体、滚装翼板的前期安装准备和过程控制,以及艉门安装过程中相关安装精度的控制,以确保艉门安装的准确性和可靠性,进而达到预期的设计要求,为后续系列船的艉门安装提供参考。 相似文献
15.
通过有限元分析,选取Workbench作为平台,采用MOGA优化算法分别对尾管轴承和中间轴承的长度和布置位置进行敏感度分析,得到轴系设计过程中各参数的不同敏感度,同时计算轴承布置位置和长度与轴系最大应力关系,得到船舶轴系的最佳优化设计方案。 相似文献
16.
17.
一种实用船型设计方法(2)--特殊船尾及其推进性能分析 总被引:2,自引:0,他引:2
介绍了四种具有完全不同尾型的实用双桨船型的优化设计结果,即双球尾船型、蜗尾船型、双尾船型、双尾鳍沿海客滚船船型,都取得了很好的推进性能与节能效果.在设计航速下,与各自的对比常规双桨船型相比较,提高推进效率分别为15%以上,20%以上,10%左右,8~10%.文中亦对特殊船尾的推进性能与螺旋桨设计作了初步分析. 相似文献
18.
In this paper, we investigate the damage to offshore platforms subjected to ship collisions. The considered scenarios are bow and stern impacts against the column of a floating platform and against the jacket legs and braces. The effect of the ship–platform interaction on the distribution of damage is studied by modeling both structures using nonlinear shell finite elements. A supply vessel of 7500-ton displacement with bulbous bow is modeled. A comprehensive numerical analysis program is conducted, and the primary findings are described herein. The collision forces from the vessel are compared with the suggested force–deformation curves in the NORSOK code. For collisions with floating platforms we particularly focus on the crushing behavior and potential penetration of the bulbous bow and stern sections into the cargo tanks or void spaces of semi-submersible platforms. For fixed jacket platforms we investigate whether jacket braces can penetrate into the ship without being subjected to significant plastic bending or local denting.Adequate treatment of the relative strength between the interacting bodies is especially relevant for impacts with high levels of available kinetic energy, for which shared energy or strength design is aimed at. Simplifying one body as rigid quickly leads to overly conservative and/or costly solutions, and is in some cases non-conservative.The numerical analysis is used to develop a novel pressure–area relation for the deformation of the bulbous bow and stern corners of the supply vessel. Procedures for strength design of the stiffened panels are discussed. Refined methods and criteria are proposed for strength design of platforms, including both floating and jacket structures. The adequacy of the NORSOK design guidance for collisions against jacket legs is evaluated. The characteristic strength of a cylindrical column is used to develop a novel criterion for the resistance to local denting from stern corners and bulbous bows. 相似文献
19.
Chen Q.Liu Z.Luo F. 《中国舰船研究》2023,(1):124-140and151
[Objectives]Aiming at the problem of poor depth-changing ability of the stern rudder of submarine at low speed, and the problem of reversing the movement trend is difficult when the stern rudder is stuck and encountering abrupt changes of seawater density in the vertical steering maneuver. This paper conducts the mechanism research of static moment maneuver. [Methods]First, it is proved through theoretical analysis that the static moment maneuver can eliminate the reversed velocity phenomenon of the stern rudder. Then, the surfacing process under the static moment maneuver and the rudder hydrodynamic control is numerically simulated. [Results]The simulation results show that the static moment maneuver can make the submarine maintain good vertical plane maneuverability at low speed, eliminate the reversed velocity phenomenon of the stern rudder, and avoid excessive trim angle of the submarine at high speed. At the same time, the recovery effect of the two emergency situations of rudder jamming and falling deep has been improved. [Conclusions]The static moment maneuver is beneficial to the maneuverability and safety of the submarine. The research in this article can provide a reference for the maneuverability design of submarine. © 2023 The Author(s). 相似文献