共查询到17条相似文献,搜索用时 203 毫秒
1.
2.
3.
4.
5.
6.
研制了调距桨装置半实物加载试验装置,包括机械加载装置、加载液压系统和电控系统.该试验装置可模拟调距桨装置在实际航行时所受的各种静态载荷.通过试验模拟加载,可获得桨毂毂桥、叶根螺栓等主要零件的应力与加载负荷的关系及分布情况,并可验证理论分析、仿真计算,为叶根螺栓等零件的优化设计提供依据. 相似文献
7.
桨毂是调距机构及桨叶等部件的安装基础构件,承受了较大的载荷.从桨毂受力的角度,模拟桨叶受力的加载重块离心力对叶根法兰中心产生的弯矩和离心力能有效模拟实际机构的推力弯矩、扭力弯矩、离心力和离心力扭矩,具备试验可行性.为评估试验误差,将有限元计算方法和试验结合应用,利用试验检验有限元计算的准确性,反之,有限元计算能有效评估... 相似文献
8.
9.
0引言船舶调距桨省去了主机换向装置,可实现船舶的无级变速,改善船舶操纵性能;其广泛应用于具有多样航行工况的运输船舶、工程船舶及军舰。本文简单介绍KL72/4-ST型调距桨的结构组成和工作原理,供同人参考。1调距桨系统调距桨系统主要由桨毂桨叶部分、调距机构、传动轴部分、配油器和液压系统等组成。1.1桨毂桨叶部分可调螺距螺旋桨的桨毂桨叶部分由桨毂和桨叶组成。桨毂内部装有调距机构,用于调整桨叶螺距; 相似文献
10.
11.
12.
13.
Stress evaluation of a submerged floating tunnel (SFT) is an issue important for determining the section dimensions required to resist environmental loads. However, the complex interaction between an SFT and surrounding fluid has confined most research on SFTs to longitudinal global time-history analyses based on Morison's equation [1]. Even though these analyses give sufficient information in the longitudinal direction, too little information about the circumferential direction compels an SFT section to be designed conservatively. This means that SFT design requires additional information on the structural behavior of the tunnel in the circumferential direction for efficient design. Accordingly, a supplementary approach by which to obtain structural responses in the circumferential direction is introduced in this paper. Upon consideration of the static responses equivalent to the dynamic behavior, three-dimensional (3-D) finite-element analyses of an SFT were performed by application of static loads corresponding to dynamic loads equivalent to those of wave, current and earthquake. The validation of each equivalent static load was supported by the results from comparison of the tension forces in mooring lines obtained using OrcaFlex [2] and ABAQUS [3]. These were used mainly for longitudinal dynamic analysis and 3-D stress evaluation, respectively, of an SFT. Based on the stresses obtained in the longitudinal and circumferential directions, the selection of suitable section dimensions for an SFT is considered. 相似文献
14.
15.
化学品船不锈钢舱热应力分析 总被引:1,自引:0,他引:1
以不锈钢舱化学品船的货舱区域平行舯体为模型来计算温差应力,并用于整个货舱区域。计算得出的温度载荷反映了航行和停?白状态下的满载和部分装载状态;将温差应力与静水弯曲应力、波浪弯曲应力以及液货和海水产生的静应力和动应力进行合成,最终结果对照许用应力,对全船和局部弯曲强度进行校核;同时研究了由于温差应力的存在对桁材轴向弯曲和剪应力、失稳强度、焊接(型式和尺寸)、开VI(形状,位置,局部加强等)的影响。 相似文献
16.
通过计算自位轴承在3MN径向静载作用下外座圈的理论比压、确定了模拟试验的载荷;采用应变测量、位移测量和试验前后试样厚度测量等三种方法,评价了自位轴上座圈代用材料ZQSn10-1的径向承载能力,模拟试验在WE100型拉压材料试验机上进行。试验结果表明,在0.08MN径向静载作用下,试样处在弹性范围内,即使载荷达0.12MN,也未生变形,由判断自位轴承的磷青铜外座圈在3MN径向静载试验载荷作用下是安全 相似文献