An evaluation framework for traffic calming measures in residential areas

The paper evaluates the effectiveness of various traffic calming measures from the perspectives of traffic performance and safety, and environmental and public health impacts. The proposed framework was applied to four calming measures – two types of speed humps, speed tables, and chicanes – to demonstrate its usefulness and applicability. A field experiment using probe vehicles equipped with global positioning system devices was conducted to obtain vehicle trajectory data for use in more realistic simulations. In addition, a recently developed vehicle emissions model was used for more accurate evaluation of environmental and public health impacts. The results show that chicane is better than the other types of traffic calming measures considered, except in terms of vehicle emissions.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

Platooning on two-lane two-way highways: An empirical investigation

This paper presents an empirical investigation into platooning on two-lane two-way highways. The main objective is to better understand this phenomenon that has important implications on traffic performance and safety. Field data from three study sites in the state of Montana were used in this study. Separate investigations were performed to examine the relationships among platoon-related variables, namely; time headway, travel speed, and platoon size. The study confirmed that interaction between successive vehicles in the traffic stream generally diminishes beyond a time headway threshold value that fell in the range of 5–7 seconds. Also, the study revealed that very short headways (less than one second) are more associated with aggressive driving and higher speeds than with slow-moving platoons due to lack of passing opportunities. Further, the study found that amount of impedance to traffic is proportional to the size of platoon as evidenced by the relative difference between mean speed of various size platoons and the mean speed of unimpeded vehicles. The study provided other valuable insights into the platooning phenomenon on two-lane highways that are essential in developing a better understanding of traffic operation on two-lane highways.     

Time-series model for vehicle speeds

This paper presents a time-series model for the spot speeds of vehicles on a road section. Based on time-series analysis techniques, the model incorporates information on the extent of existing dependency between the speeds of successive vehicles. The model for the data is chosen while relying heavily on the data, and thus emphasis is given to their special characteristics. The advantages of using the model are examined with regard to the relative speed of two successive vehicles along a road section. The results are compared with those obtained by using a model of independent observations; fewer errors are obtained with the time-series model. Therefore, it is concluded that the sequence of speed observations contains valuable information which should be incorporated into speed models.     

Updating free speed models through mechanistic principles for Indian conditions

The prediction of free speeds of vehicles is an integral part of the economic appraisal of highways. It is to be noted that speeds not only govern the travel time costs, but also have major impacts on Vehicle Operating Costs (VOC). The World Bank has proposed a mechanistic free speed model based on the limiting speed concept for Highway Design and Maintenance (HDM)‐III. This model along with some refinements has been included in HDM‐4. The underlying assumption in the HDM free speed prediction model is that the free speed at any given point of time is the minimum of possible constraining speeds. This paper mainly addresses the methodology considered to update the free speed models through mechanistic principles (based on HDM‐4). This is accomplished by calibration of the model using the current data on free speeds, road and vehicle characteristics. Subsequently, the validation of the developed models has been carried out.     

A recursive, cell processing model for predicting freeway travel times

Travel time information influences driver behaviour and can contribute to reducing congestion and improving network efficiency. Consequently many road authorities disseminate travel time information on road side signs, web sites and radio traffic broadcasts. Operational systems commonly rely on speed data obtained from inductive loop detectors and estimate travel times using simple algorithms that are known to provide poor predictions particularly on either side of the peak period. This paper presents a new macroscopic model for predicting freeway travel times which overcomes the limitations of operational ‘instantaneous’ speed models by drawing on queuing theory to model the processing of vehicles in sections or cells of the freeway. The model draws on real-time speed, flow and occupancy data and is formulated to accommodate varying geometric conditions, the relative distribution of vehicles along the freeway, variations in speed limits, the impact of ramp flows and fixed or transient bottlenecks. Field validation of the new algorithm was undertaken using data from two operational freeways in Melbourne, Australia. Consistent with the results of simulation testing, the validation confirmed that the recursive model provided a substantial improvement in travel time predictions when compared to the model currently used to provide real-time travel time information to motorists in Melbourne.     

Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

A driving force model for non-strict priority crossing behaviors of right-turn drivers

At urban intersections, conflicts between right-turn vehicles and through non-motorized vehicles are a critical cause of traffic congestion and safety challenges. Based on the fact that in different countries there is no strict priority in conflicts between motorized and non-motorized vehicles, this study focused on analysis of the inherent mechanism of this universal phenomenon. By the analogy of a force model for moving vehicles, this paper developed a micro driving force model, including the safety driving force and efficiency driving force, for right-turn drivers which constitute the dominant party during the non-strict priority crossing process. We further demonstrate that the strict priority crossing behavior is a special case of the proposed driving force model. All the parameters used in this model were calibrated through field data collected at twelve signalized intersection sites in Shanghai. Model validation results proved the accuracy and reliability of the proposed driving force model. The model was further proved that it can be used for right-turn vehicle's average crossing speed prediction. The sensitivity analysis identified the influence of vehicle type, non-motorized traffic flow rate, and non-motorized traffic speed on the average speed, and offered support for the rationality of the non-strict priority.     

Evaluating speed consistency between successive elements of a two-lane rural highway

The V₈₅ speed reflects the 85th percentile speed of vehicles in a traffic stream passing a given element on the highway section. The large amount of speed differential in V₈₅ between the two successive elements along a highway reflects lack of speed consistency in the highway section. This lack of speed consistency can result in increased crash risk. Recent research points to several problems associated with the conventional method of measuring ΔV₈₅ between successive highway elements: (1) failure to reflect individual vehicle speed profiles; and (2) failure to account for inter-dependence in individual vehicle speeds between successive elements. These problems have serious implications for justifying safety treatment when conventional ΔV₈₅ measure is applied. A number of researchers have suggested that the estimated speed differential based on individual vehicle speed profiles in successive elements is significantly higher than that obtained using the conventional approach. In this paper, we assess the safety implications of using the conventional ΔV₈₅ and introduce a hierarchical model for considering individual vehicles speed consistency. These findings lead to important implications for introducing engineering treatments to improve safety along in two-lane rural highways based on the criteria of speed consistency.     

Speed or spacing? Cumulative variables,and convolution of model errors and time in traffic flow models validation and calibration

This paper proves that in traffic flow model calibration and validation the cumulative sum of a variable has to be preferred to the variable itself as a measure of performance. As shown through analytical relationships, model residuals dynamics are preserved if discrepancy measures of a model against reality are calculated on a cumulative variable, rather than on the variable itself. Keeping memory of model residuals occurrence times is essential in traffic flow modelling where the ability of reproducing the dynamics of a phenomenon – as a bottleneck evolution or a vehicle deceleration profile – may count as much as the ability of reproducing its order of magnitude. According to the aforesaid finding, in a car-following models context, calibration on travelled space is more robust than calibration on speed or acceleration. Similarly in case of macroscopic traffic flow models validation and calibration, cumulative flows are to be preferred to flows. Actually, the findings above hold for any dynamic model.     

Alterations to the transyt-7F model to represent near-side transit stops

Transit vehicles stopping to load/unload passengers on-line at a signalized intersection can obstruct the flow of other vehicles. The TRANSYT model ignores the delay to other traffic caused by this loading/unloading process. This can cause TRANSYT to use incorrect flow profiles, resulting in signal timings that cater to these profiles rather than the actual ones. This paper describes a new model for representing near-side transit stops in lanes shared by public transit and private vehicles, and its implementation into the TRANSYT-7F program. The results of an initial application of the proposed model are also described. The proposed model, which is a deterministic simulation model, is able to represent the effect of near-side transit stops on the other traffic; this representation covers both total and partial blockage of the approaches during the transit loading. The procedure has been incorporated into the TRANSYT-7F program. This allows appropriate representation of the adverse effects of transit loading on-line during a green phase. It thus encourages the TRANSYT optimizer to push transit loading to the red phases.     

Heteroscedastic Gaussian processes for uncertainty modeling in large-scale crowdsourced traffic data

Accurately modeling traffic speeds is a fundamental part of efficient intelligent transportation systems. Nowadays, with the widespread deployment of GPS-enabled devices, it has become possible to crowdsource the collection of speed information to road users (e.g. through mobile applications or dedicated in-vehicle devices). Despite its rather wide spatial coverage, crowdsourced speed data also brings very important challenges, such as the highly variable measurement noise in the data due to a variety of driving behaviors and sample sizes. When not properly accounted for, this noise can severely compromise any application that relies on accurate traffic data. In this article, we propose the use of heteroscedastic Gaussian processes (HGP) to model the time-varying uncertainty in large-scale crowdsourced traffic data. Furthermore, we develop a HGP conditioned on sample size and traffic regime (SSRC-HGP), which makes use of sample size information (probe vehicles per minute) as well as previous observed speeds, in order to more accurately model the uncertainty in observed speeds. Using 6 months of crowdsourced traffic data from Copenhagen, we empirically show that the proposed heteroscedastic models produce significantly better predictive distributions when compared to current state-of-the-art methods for both speed imputation and short-term forecasting tasks.     

Experimental and empirical investigations of traffic flow instability

Traffic instability is an important but undesirable feature of traffic flow. This paper reports our experimental and empirical studies on traffic flow instability. We have carried out a large scale experiment to study the car-following behavior in a 51-car-platoon. The experiment has reproduced the phenomena and confirmed the findings in our previous 25-car-platoon experiment, i.e., standard deviation of vehicle speeds increases in a concave way along the platoon. Based on our experimental results, we argue that traffic speed rather than vehicle spacing (or density) might be a better indicator of traffic instability, because vehicles can have different spacing under the same speed. For these drivers, there exists a critical speed between 30 km/h and 40 km/h, above which the standard deviation of car velocity is almost saturated (flat) along the 51-car-platoon, indicating that the traffic flow is likely to be stable. In contrast, below this critical speed, traffic flow is unstable and can lead to the formation of traffic jams. Traffic data from the Nanjing Airport Highway support the experimental observation of existence of a critical speed. Based on these findings, we propose an alternative mechanism of traffic instability: the competition between stochastic factors and the so-called speed adaptation effect, which can better explain the concave growth of speed standard deviation in traffic flow.     

Simulating the environmental effects of isolated and area-wide traffic calming schemes using traffic simulation and microscopic emission modeling

This study focuses on the development of a microscopic traffic simulation and emission modeling system which aims at quantifying the effects of different types of traffic calming measures on vehicle emissions both at a link-level and at a network-level. It also investigates the effects of isolated traffic-calming measures at a corridor level and area-wide calming schemes, using a scenario analysis. Our study is set in Montreal, Canada where a traffic simulation model for a dense urban neighborhood is extended with capabilities for microscopic emission estimation. The results indicate that on average, isolated calming measures increase carbon dioxide (CO₂), carbon monoxide (CO), and nitrogen oxides (NO_x) emissions by 1.5, 0.3, and 1.5 %, respectively across the entire network. Area-wide schemes result in a percentage increase of 3.8 % for CO₂, 1.2 % for CO, and 2.2 % for NO_x across the entire network. Along specific corridors where traffic calming measures were simulated, increases in emissions of up to 83 % were observed. We also account for the effect of different measures on traffic volumes and observe moderate decreases in areas that have undergone traffic calming. In spite of traffic flow reductions, total emissions do increase.     

Decision-making on Large Infrastructure Projects: The Role of the Dutch Parliament

Abstract

Validating microscopic traffic simulation models incorporates several challenges because of the inadequacy and rareness of validation data, and the complexity of the car following and lane-changing processes. In addition, validation data were usually measured in aggregate form at the link level and not at the level of the individual vehicle. The majority of model validation attempts in the literature use average link measurements of traffic characteristics. However, validation techniques based on averages of traffic variables have several limitations including possible inconsistency between the field observed and simulation-estimated variables, and as such the resulting spatial–temporal traffic stream patterns.

Due to these inconsistencies, this paper introduces a novel approach to the validation of microscopic traffic simulation models. A three-stage procedure for validating microscopic simulation models is presented. The paper describes the field measurements, experimental setup, and the simulation-based analysis of the three stages. The purpose of the first stage is to validate a benchmark simulator (NETSIM) using limited field data. The second stage examines the spatial–temporal traffic patterns extracted from the benchmark simulator versus those extracted from the simulation model to be validated (I-SIM-S). Different traffic patterns were examined accounting for various factors, such as traffic flow, link speeds, and signal timing. The third stage compares the aggregate traffic measures extracted from the subject simulator against those extracted from the benchmark simulator.     

Speed profile estimation using license plate recognition data

Vehicle speed profile is a fundamental data support for calculating vehicular emission using the micro-emission model. However, achieving accuracy and breadth for the speed profile estimation is difficult. This study proposes a new vehicle speed profile estimation model using license plate recognition (LPR) data. This model allows speed profile estimation of every individual vehicle between two consecutive intersections. A systematic LPR data-mending method is developed to infer the information of unmatched vehicles. Using the complete arrival and departure information as boundary conditions, a customized car-following model combined with dummy-overtaking hypothesis and boundary constraints is then applied to estimate the speed profile of vehicles. The proposed model is validated using ground truth speed information from a field experiment conducted in Langfang City in China. Results show that the model can fully capture the pattern of ground truth speed profile. A complementary model validation using the Next Generation Simulation dataset and a model application for calculating emissions are also conducted. The numerical results indicate the effectiveness of the proposed model in estimating vehicle speed profile and emissions.     

Reprint of: Modelling the impact of traffic incidents on travel time reliability

Traffic incidents are recognised as one of the key sources of non-recurrent congestion that often leads to reduction in travel time reliability (TTR), a key metric of roadway performance. A method is proposed here to quantify the impacts of traffic incidents on TTR on freeways. The method uses historical data to establish recurrent speed profiles and identifies non-recurrent congestion based on their negative impacts on speeds. The locations and times of incidents are used to identify incidents among non-recurrent congestion events. Buffer time is employed to measure TTR. Extra buffer time is defined as the extra delay caused by traffic incidents. This reliability measure indicates how much extra travel time is required by travellers to arrive at their destination on time with 95% certainty in the case of an incident, over and above the travel time that would have been required under recurrent conditions. An extra buffer time index (EBTI) is defined as the ratio of extra buffer time to recurrent travel time, with zero being the best case (no delay). A Tobit model is used to identify and quantify factors that affect EBTI using a selected freeway segment in the Southeast Queensland, Australia network. Both fixed and random parameter Tobit specifications are tested. The estimation results reveal that models with random parameters offer a superior statistical fit for all types of incidents, suggesting the presence of unobserved heterogeneity across segments. What factors influence EBTI depends on the type of incident. In addition, changes in TTR as a result of traffic incidents are related to the characteristics of the incidents (multiple vehicles involved, incident duration, major incidents, etc.) and traffic characteristics.     

Noise prediction for highways in Thailand

A model of highway traffic noise is formulated based on vehicle types. The data were collected from local highways in Thailand with free-flow traffic conditions. First, data on vehicle noise was collected from individual vehicles using sound level meters placed at a reference distance. Simultaneously, measurements were made of vehicles’ spot speeds. Secondly, are data for building the highway traffic noise model. This consists of traffic noise levels, traffic volumes by vehicle classification, average spot speeds by vehicle type, and the geometric dimension of highway sections. The free-flow traffic noise model is generated from this database. A reference energy mean emission level (the basic noise) level for each type of vehicles is developed based on direct measurement of Leq (10 s) from the real running condition of each type of vehicles. Modification of terms and parameters are used to make the model fit highway traffic characteristics and different types of vehicle.     

Towards a real-time microscopic emissions model

This article presents a new approach to microscopic road traffic exhaust emission modelling. The model described uses data from the SCOOT demand-responsive traffic control system implemented in over 170 cities across the world. Estimates of vehicle speed and classification are made using data from inductive detector loops located on every SCOOT link. This data feeds into a microscopic traffic model to enable enhanced modelling of the driving modes of vehicles (acceleration, deceleration, idling and cruising). Estimates of carbon monoxide emissions are made by applying emission factors from an extensive literature review. A critical appraisal of the development and validation of the model is given before the model is applied to a study of the impact of high emitting vehicles. The article concludes with a discussion of the requirements for the future development and benefits of the application of such a model.