Vehicle Handling Improvement by Active Steering

Summary This paper first analyses some stability aspects of vehicle lateral motion, then a coprime factors and linear fractional transformations (LFT) based feedforward and feedback H 8 control for vehicle handling improvement is presented. The control synthesis procedure uses a linear vehicle model which includes the yaw motion and disturbance input with speed and road adhesion variations. The synthesis procedure allows the separate processing of the driver reference signal and robust stabilization problem or disturbance rejection. The control action is applied as an additional steering angle, by combination of the driver input and feedback of the yaw rate. The synthesized controller is tested for different speeds and road conditions on a nonlinear model in both disturbance rejection and driver imposed yaw reference tracking maneuvers.     

Lateral handling improvement with dynamic curvature control for an independent rear wheel drive EV

The integrated longitudinal and lateral dynamic motion control is important for four wheel independent drive (4WID) electric vehicles. Under critical driving conditions, direct yaw moment control (DYC) has been proved as effective for vehicle handling stability and maneuverability by implementing optimized torque distribution of each wheel, especially with independent wheel drive electric vehicles. The intended vehicle path upon driver steering input is heavily depending on the instantaneous vehicle speed, body side slip and yaw rate of a vehicle, which can directly affect the steering effort of driver. In this paper, we propose a dynamic curvature controller (DCC) by applying a the dynamic curvature of the path, derived from vehicle dynamic state variables; yaw rate, side slip angle, and speed of a vehicle. The proposed controller, combined with DYC and wheel longitudinal slip control, is to utilize the dynamic curvature as a target control parameter for a feedback, avoiding estimating the vehicle side-slip angle. The effectiveness of the proposed controller, in view of stability and improved handling, has been validated with numerical simulations and a series of experiments during cornering engaging a disturbance torque driven by two rear independent in-wheel motors of a 4WD micro electric vehicle.     

Using µ Feedforward for Vehicle Stability Enhancement

A differential braking control strategy using yaw rate feedback, coupled with µ feedforward is introduced for a vehicle cornering on different µ roads. A nonlinear 4-wheel car model is developed. A desired yaw rate is calculated from the reference model based on the driver steering input. It is shown that knowledge of µ offers significant improvement of the vehicle desired trajectory over that of a yaw rate controller alone. Uncertainties and time delay in estimating µ are shown to still yield a system that is superior to using no µ information at all.     

Using µ Feedforward for Vehicle Stability Enhancement

A differential braking control strategy using yaw rate feedback, coupled with µ feedforward is introduced for a vehicle cornering on different µ roads. A nonlinear 4-wheel car model is developed. A desired yaw rate is calculated from the reference model based on the driver steering input. It is shown that knowledge of µ offers significant improvement of the vehicle desired trajectory over that of a yaw rate controller alone. Uncertainties and time delay in estimating µ are shown to still yield a system that is superior to using no µ information at all.     

A lateral driver model for vehicle–driver closed-loop simulation at the limits of handling

This paper presents a lateral driver model for vehicle–driver closed-loop simulation at the limits of handling. An appropriate driver model can be used to evaluate the performance of vehicle chassis control systems via computer simulations before vehicle tests which incurs expenses especially at the limits of handling. The driver model consists of two parts. The first part is an upper-level controller employing force-based approach to reduce the number of unknown vehicle parameters. The feedforward part of the upper controller has been designed by using the centre of percussion. The feedback part aims to minimise ‘tangential error’, defined as the sum of body slip angle and yaw error, to match vehicle direction and road heading angle. The part is designed to regenerate an appropriate skid motion similar to that of a professional driver at the limits. The second part is a lower-level controller which converts the desired front lateral force to steering wheel angle. The lower-level controller also consists of feedforward and feedback parts. A two-degree-of-freedom bicycle model-based feedforward part provides nominal steering wheel angle, and the feedback part aims to eliminate unmodelled error. The performance of the lateral driver model has been investigated via computer simulations. It has been shown that the steering behaviours of the proposed driver model are quite close to those of a professional driver at the limits. Compared with the previously developed lateral driver models, the proposed lateral driver model shows good tracking performance at the limits of handling.     

Modeling and control of an anti-lock brake and steering system for cooperative control on split-mu surfaces

The brake and steering systems in vehicles are the most effective actuators that directly affect the vehicle dynamics. In general, the brake system affects the longitudinal dynamics and the steering system affects the lateral dynamics; however, their effects are coupled when the vehicle is braking on a non-homogenous surface, such as a split-mu road. The yaw moment compensation of the steering control on a split-mu road is one of the basic functions of integrated or coordinated chassis control systems and has been demonstrated by several chassis suppliers. However, the disturbance yaw moment is generally compensated for using the yaw rate feedback or using wheel brake pressure measurement. Access to the wheel brake pressure through physical sensors is not cost effective; therefore, we modeled the hydraulic brake system to avoid using physical sensors and to estimate the brake pressure. The steering angle controller was designed to mitigate the non-symmetric braking force effect and to stabilize the yaw rate dynamics of the vehicle. An H-infinity design synthesis was used to take the system model and the estimation errors into account, and the designed controller was evaluated using vehicle tests.     

Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Application of Aerodynamic Actuators to Improve Vehicle Handling

This exploratory study considers applications of active aerodynamic devices for suppressing parasitic motion and for improving the response of vehicles to steering, within the scope of the linear dynamic behaviour. A three DOF linear model is chosen to describe the side slip, yaw and roll motion of a baseline front-wheel steered vehicle. The improvements in performance of the base-line vehicle that are achievable by the application of direct yaw and roll moments are determined when either an open loop control pre-filter or a state feedback control law based on LQR design is applied. Unlike the former control, the state feedback control is unable to make the body side-slip angle vanish. The feedback control performance of each of the two moment actuators has been examined separately and then jointly. The advantages of combining the open loop and feedback dual actuator configurations are demonstrated using the two-degree of freedom control scheme. It is found that the scheme yields a spectacular performance but demands unreasonably large moments from the actuators in the context of available aerodynamic forces. On the other hand, the demand on direct yaw and roll moment of actuators is modest when the actuators are controlled using the LQR feedback only and if the control design is used to track a desired yaw rate trajectory and simultaneously to reduce the parasitic rolling motion. Significant improvements in handling and dynamic stability of a base-line vehicle can be achieved by aerodynamically generated direct yaw and roll actuator moments provided the target control performance is reasonable. The configurations of aerodynamic actuators considered are feasible for improving vehicle handling in cornering on motorways but more work remains to be done to explore alternative aerodynamic configurations that give rise to less side effects and higher lift coefficients.     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

智能汽车自动紧急转向避撞的跟踪控制方法对比研究

为了提高智能汽车的主动安全性,提出3种不同的自动紧急转向避撞跟踪控制方法。首先建立汽车避撞简化模型,对制动、转向及两者相结合的3种不同避撞方式进行对比分析。其次,为深入研究汽车避撞过程中的实际响应,建立包含转向、制动及悬架3个子系统耦合特性的底盘18自由度统一动力学模型,并进行相关试验验证。随后构建智能汽车自动紧急转向避撞控制框架,对五次多项式参考路径和七次多项式参考路径的横摆角速度和横摆角加速度进行对比分析。接着以线性2自由度转向动力学模型为参考对象,对最优控制四轮转向、最优控制前轮转向、前馈与反馈控制相结合的前轮转向3种不同的跟踪控制系统分别进行设计。最后,以汽车底盘18自由度统一动力学模型为研究对象,对上述3种避撞控制系统进行仿真试验对比分析。研究结果表明：与制动避撞相比而言,转向避撞所需的纵向距离有较大降低,随着车速的增加和路面附着系数的越低,效果越明显;七次多项式参考路径比五次多项式参考路径的避撞过渡过程更为平缓,当实际车速与控制器所用车速不一致时,前者避撞性能表现更优;最优四轮转向控制系统在高、低2种不同附着路面都具有较好的避撞效果,最优前轮转向控制系统次之,而前馈与反馈相结合的前轮转向控制系统在低附着路面上则表现出严重的失稳。     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

An investigation on motor-driven power steering-based crosswind disturbance compensation for the reduction of driver steering effort

This paper describes a lateral disturbance compensation algorithm for an application to a motor-driven power steering (MDPS)-based driver assistant system. The lateral disturbance including wind force and lateral load transfer by bank angle reduces the driver's steering refinement and at the same time increases the possibility of an accident. A lateral disturbance compensation algorithm is designed to determine the motor overlay torque of an MDPS system for reducing the manoeuvreing effort of a human driver under lateral disturbance. Motor overlay torque for the compensation of driver's steering torque induced by the lateral disturbance consists of human torque feedback and feedforward torque. Vehicle–driver system dynamics have been investigated using a combined dynamic model which consists of a vehicle dynamic model, driver steering dynamic model and lateral disturbance model. The human torque feedback input has been designed via the investigation of the vehicle–driver system dynamics. Feedforward input torque is calculated to compensate additional tyre self-aligning torque from an estimated lateral disturbance. The proposed compensation algorithm has been implemented on a developed driver model which represents the driver's manoeuvreing characteristics under the lateral disturbance. The developed driver model has been validated with test data via a driving simulator in a crosswind condition. Human-in-the-loop simulations with a full-scale driving simulator on a virtual test track have been conducted to investigate the real-time performance of the proposed lateral disturbance compensation algorithm. It has been shown from simulation studies and human-in-the-loop simulation results that the driver's manoeuvreing effort and a lateral deviation of the vehicle under the lateral disturbance can be significantly reduced via the lateral disturbance compensation algorithm.     

Steering disturbance rejection using a physics-based neuromusculoskeletal driver model

The aim of this work is to develop a comprehensive yet practical driver model to be used in studying driver–vehicle interactions. Drivers interact with their vehicle and the road through the steering wheel. This interaction forms a closed-loop coupled human–machine system, which influences the driver's steering feel and control performance. A hierarchical approach is proposed here to capture the complexity of the driver's neuromuscular dynamics and the central nervous system in the coordination of the driver's upper extremity activities, especially in the presence of external disturbance. The proposed motor control framework has three layers: the first (or the path planning) plans a desired vehicle trajectory and the required steering angles to perform the desired trajectory; the second (or the musculoskeletal controller) actuates the musculoskeletal arm to rotate the steering wheel accordingly; and the final layer ensures the precision control and disturbance rejection of the motor control units. The physics-based driver model presented here can also provide insights into vehicle control in relaxed and tensed driving conditions, which are simulated by adjusting the driver model parameters such as cognition delay and muscle co-contraction dynamics.     

A curving ACC system with coordination control of longitudinal car-following and lateral stability

The paper presents a curving adaptive cruise control (ACC) system that is coordinated with a direct yaw-moment control (DYC) system and gives consideration to both longitudinal car-following capability and lateral stability on curved roads. A model including vehicle longitudinal and lateral dynamics is built first, which is as discrete as the predictive model of the system controller. Then, a cost function is determined to reflect the contradictions between vehicle longitudinal and lateral dynamics. Meanwhile, some I/O constraints are formulated with a driver permissible longitudinal car-following range and the road adhesion condition. After that, desired longitudinal acceleration and desired yaw moment are obtained by a linear matrix inequality based robust constrained state feedback method. Finally, driver-in-the-loop tests on a driving simulator are conducted and the results show that the developed control system provides significant benefits in weakening the impact of DYC on ACC longitudinal car-following capability while also improving lateral stability.     

Handling Capabilities of Vehicles in Emergencies Using Coordinated AFS and ARMC Systems

In this paper, an advanced control technique that can be implemented in hard emergency situations of vehicles is introduced. This technique suggests integration between Active Front Steering (AFS) and Active Roll Moment Control (ARMC) systems in order to enhance the vehicle controllability. For this purpose, the AFS system applies a robust sliding mode controller (SMC) that is designed to influence the steering input of the driver by adding a correction steering angle for maintaining the vehicle yaw rate under control all the time. The AFS system is then called active-correction steering control. The ARMC system is designed to differentiate the front and rear axles' vertical suspension forces in order to alter the vehicle yaw rate and to eliminate the vehicle roll motion as well. Moreover, the operation of the SMC is based on tracking the behavior of a nonlinear 2-wheel model of 2-DOF used as a reference model. The 2-wheel model incorporates real tire characteristics, which can be inferred by the use of trained neural networks. The results clearly demonstrate the enhanced characteristics of the proposed control technique. The SMC with the assistance of the ARMC provides less correction of the steering angle and accordingly reduces the possibility of occurrence of the saturation phenomenon that is likely to take place in the operation of the SMC systems.     

Handling Capabilities of Vehicles in Emergencies Using Coordinated AFS and ARMC Systems

In this paper, an advanced control technique that can be implemented in hard emergency situations of vehicles is introduced. This technique suggests integration between Active Front Steering (AFS) and Active Roll Moment Control (ARMC) systems in order to enhance the vehicle controllability. For this purpose, the AFS system applies a robust sliding mode controller (SMC) that is designed to influence the steering input of the driver by adding a correction steering angle for maintaining the vehicle yaw rate under control all the time. The AFS system is then called active-correction steering control. The ARMC system is designed to differentiate the front and rear axles' vertical suspension forces in order to alter the vehicle yaw rate and to eliminate the vehicle roll motion as well. Moreover, the operation of the SMC is based on tracking the behavior of a nonlinear 2-wheel model of 2-DOF used as a reference model. The 2-wheel model incorporates real tire characteristics, which can be inferred by the use of trained neural networks. The results clearly demonstrate the enhanced characteristics of the proposed control technique. The SMC with the assistance of the ARMC provides less correction of the steering angle and accordingly reduces the possibility of occurrence of the saturation phenomenon that is likely to take place in the operation of the SMC systems.     

Design and evaluation of sideslip angle observer for vehicle stability control

This paper presents a method for estimating the vehicle side slip angle, which is considered as a significant signal in determining the vehicle stability region in vehicle stability control systems. The proposed method combines the model-based method and kinematics-based method. Side forces of the front and rear axles are provided as a weighted sum of directly calculated values from a lateral acceleration sensor and a yaw rate sensor and from a tire model according to the nonlinear factor, which is defined to identify the degree of nonlinearity of the vehicle state. Then, the side forces are fed to the extended Kalman filter, which is designed based on the single-track vehicle model associated with a tire model. The cornering stiffness identifier is introduced to compensate for tire force nonlinearities. A fuzzy-logic procedure is implemented to determine the nonlinear factor from the input variables: yaw rate deviation from the reference value and lateral acceleration. The proposed observer is compared with a model-based method and kinematics-based method. An 8 DOF vehicle model and Dugoff tire model are employed to simulate the vehicle state in MATLAB/SIMULINK. The simulation results shows that the proposed method is more accurate than the model-based method and kinematics-based method when the vehicle is subjected to severe maneuvers under different road conditions.     

Active front wheel steering model and controller for integrated dynamics control systems

We report a model and controller for an active front-wheel steering (AFS) system. Two integrated dynamics control (IDC) systems are designed to investigate the performance of the AFS system when integrated with braking and steering systems. An 8-degrees-of-freedom vehicle model was employed to test the controllers. The controllers were inspected and compared under different driving and road conditions, with and without braking input, and with and without steering input. The results show that the AFS system performs kinematic steering assistance function and kinematic stabilisation function very well. Three controllers allowed the yaw rate to accurately follow a reference yaw rate, improving the lateral stability. The two IDC systems improved the lateral stability and vehicle control and were effective in reducing the sideslip angle.     

基于MPC的分布式驱动越野车辆原地转向控制研究

针对轮毂电机分布式驱动越野车辆在狭小空间快速机动的需求,设计了一种分层结构的原地转向控制策略。基于动力学原理分析了各轮载荷、附着条件对原地转向横摆速度的影响机理,并搭建原地转向运动学模型,上层采用模型预测控制算法设计原地转向理想轨迹以及期望的横摆角速度,开发基于PI滑模控制的横摆运动跟踪算法,通过补偿转向横摆力矩以提高方向角控制的鲁棒性和稳定性,下层以最优轮胎利用率为目标,设计二次规划算法优化分配各轮附加横摆力矩。dSPACE硬件在环测试结果表明,所提出的控制算法可在保证稳定性的前提下实现原地转向,大幅提高了车辆的转向机动性,在方向盘动态输入仿真中,车辆最大转弯半径为0.157 m,转向中心的最大偏移量为3.610 m;同时,驾驶员能对转向过程进行闭环控制,实现了原地转向过程中横摆速度的实时调节。     

汽车爆胎特性建模与主动制动控制策略

为了提高汽车在突发爆胎事故时的稳定性,对爆胎汽车主动制动控制策略进行了研究。根据车轮爆胎时间与压力变化的关系,在UniTire模型基础上建立了爆胎模型;根据电子稳定性控制系统中横摆角速度及质心侧偏角对汽车稳定性影响的关系,基于二自由度汽车动力学模型,通过计算汽车横摆角速度及质心侧偏角实际值与理想值的偏差,并基于线性二次型调节器最优控制方法决策出最优附加横摆力矩,从而修正爆胎后汽车的运动状态。最后通过计算机仿真对所提策略的有效性进行了验证。结果表明：主动制动控制策略可以保证爆胎过程中汽车的行驶稳定性和安全性。