Road Surface Correction o f Tire Test Data

SUMMARY

Most tire data used for vehicle simulations is measured on laboratory test facilities. An investigation showed that the frictional properties of these laboratory machines can be quite different from actual road conditions. This paper describes a method to correct laboratory tire test data to be more like road data in order to achieve a higher degree of correlation between instrumented test- and simulation results.     

Sideslip angle estimation based on input–output linearisation with tire–road friction adaptation

An adaptive sideslip angle observer considering tire–road friction adaptation is proposed in this paper. The single-track vehicle model with nonlinear tire characteristics is adopted. The tire parameters can be easily obtained through road test data without using special test rigs. Afterwards, this model is reconstructed and a high-gain observer (HGO) based on input–output linearisation is derived. The observer stability is analysed. Experimental results have confirmed that the HGO has a better computational efficiency with the same accuracy when compared with the extended Kalman filter and the Luenberger observer. Finally, a road friction adaptive algorithm based on vehicle lateral dynamics is proposed and validated through driving simulator data. As long as the tires work in the nonlinear region, the maximal friction coefficient could be estimated. This algorithm has excellent portability and is also suitable for other observers.     

基于IS0362-1：2007的M1类车辆轮胎噪声影响研究

介绍了汽车加速行驶车外噪声测量标准ISO362—1：2007的试验流程和数据处理方法,并与现行标准进行了比较。在此基础上,重点分析了新标准下轮胎噪声对M1类车辆噪声测试结果的影响,结果表明：轮胎噪声对加速噪声结果的影响有了大幅度提高,甚至成了影响试验结果的决定性因素,并对此进行了相关的试验验证。     

车轮轮胎总成的路障冲击试验

轮毂的性能直接影响汽车的行驶安全和乘客的人身安全,车轮轮胎总成的路障冲击试验对轮毂的性能有了更高的要求。文章通过从SAEJ1981标准的总体要求、试验范围及冲击方式等方面的介绍提供了引导开发新的车轮轮胎总成路障冲击试验的背景信息,表明SAEJ1981标准能公正地评估车轮和轮胎总成的路障冲击试验,指出国内在车轮新品验证过程和周期性试验中也应增加该冲击试验项目,以充分保障产品的安全性。     

纯电动汽车轮胎磨损关键影响因素研究

木文在分析纯电动车汽车不同于传统燃油车对于轮胎磨损关键因素的基础上,对纯电动车汽车轮胎磨损影响因素进行了试验验证。试验针对栽荷及动力系统两个因素采用控制单一变量法进行轮胎道路磨损试验,并通过对试验路线优化及驾驶员驾驶习惯的约束,使得测试结果更加准确及客观。最后对测试完成之后的轮胎花纹形态、轮胎花纹深度及轮胎预计里程寿命进行了详细数据分析。     

基于车路系统的事故现场轮胎印迹强度参数化研究

为明确事故现场可视轮胎印迹强度与车辆动力学特性、轮胎橡胶磨损特征及道路表面灰度之间的关联特性,提出基于车路耦合的事故现场轮胎印迹强度参数化研究方法。通过结合动态滑动摩擦因数模型及轮胎非线性模型,建立车辆路面9 DOF非线性系统动力学模型,运用VBOX惯性测量技术验证模型的有效性。运用胎面磨损能量模型,从车路系统角度确定车辆、轮胎和路面特性对轮胎全局摩擦力及胎面磨损特性的影响。结合印迹强度特征模型提出轮胎印迹强度参数研究方法,选取不同制动、转向角工况及3组路面、胎面特性对轮胎路面接地力学特性、胎面橡胶磨损量、可视轮胎印迹特征进行仿真分析。结果表明：印迹强度仅与全局摩擦力大小有关,与轮胎路面滑移方向无关;滑移工况下胎面橡胶磨损量随着全局摩擦力和滑移速度的增大而增大,而印迹强度变化不明显;制动力矩和道路表面灰度对产生可视轮胎印迹起决定作用,转向角主要影响不规则可视轮胎印迹的产生;前轮轮胎最先出现可视印迹,且可视印迹长度和强度均高于后轮轮胎;采取可视印迹起点作为事故车辆速度判定具有一定的误差,应根据具体情况进行具体分析;研究成果能够为基于可视轮胎印迹的交通事故重建提供理论基础。     

Tire Lateral Force Estimation Using Kalman Filter

As for the tire analysis, lateral tire force is a fundamental factor that describes the stability of vehicle handling. Attempts to analyze the vehicle stability have been made based on various objective test methods and some specific factors such as yaw, lateral acceleration and roll angle. However, the problem to identify which axle is lack of the tire grip at a certain situation still remains. Since indoor tire force measurement system cannot represent a real road and vehicle conditions, tire force measurement through a real vehicle test is inevitable. Due to the high price of the tire force measurement device, tire force estimator can be an alternative toward cost reduction and device failure. In this paper, nonlinear planar full car model combined with tire model is proposed. Then, using discrete-time extended Kalman-Bucy filter (EKBF), individual tire lateral force are estimated with modified relaxation length model.     

车轮与轮胎设计间隙研究

本文以解决某款新车型正向设计轮罩在车辆在综合耐久路试过程中出现了前轮胎和轮罩干涉的现象对轮胎与轮罩间隙设计的因素进行研究分析,增加了新的轮胎包络工况明确了轮胎和轮罩的预留间隙值.     

轮胎非稳态转向特性非线性仿真模型

本文以轮与路面之间的滑移速度为出发点，在稳态指数统一模型的基础上，建立了轮胎非稳态转向特性非线性仿真模型。在实验研究中，发现了动态过程回正力臂和附加的回正力矩的滞后特性。仿真和试验结果对比表明，该模型足以反映轮胎非线性转向特性，可用于前轮及汽车操纵动力学仿真方面的研究。     

Design of a signal transducer for direct conversion of wheel linear accelerations into tire lateral forces

This paper describes a design of a real-time conversion system of wheel linear accelerations into tire lateral forces. Though the tire lateral forces are important elements for analyzing vehicle dynamic control performances, they cannot be easily measured in real-time owing to the non-linearities of tire dynamics, friction, and slippage on road. In this paper, we propose a practical direct method using wheel linear accelerations in order to estimate tire lateral forces transmitted into the vehicle in real-time. A simplified vehicle model based on force-acceleration analysis is proposed to assure the real-time performance. The acceleration values are obtained using three-axis accelerometers attached on each wheel location. For conditioning and rectifying the acceleration signals, a signal transducer is designed using a digital filter. And in order to investigate the feasibility and real-time performance, a prototype of signal transducer is fabricated using a digital signal processor. The experimental results and performance are validated with the road test results using six-component wheel force transducers.     

轻型货车轮胎接地压力分布实测

利用自主开发的轮胎接地压力测试仪,进行了轻型货车不同花纹和不同使用年限轮胎,在不同轮胎胎压和不同负荷作用下,轮胎的接地压力分布规律测量。实测结果发现:轻型货车轮胎与路面的接触形状更接近于矩形;新胎比旧胎的接地压力要均匀些;轮胎胎压与平均接地压力、轮胎负荷与平均接地压力、轮胎负荷与有效接地面积基本上呈线性关系。     

独立悬架车辆转向轮侧滑及其影响因素的试验研究

结合独立悬架车辆转向轮定位参数的特点,采用二元二次回归正交组合设计方法设计了试验方案,并对影响转向轮侧滑的轮胎胎压、载荷和车速等相关因素进行了试验研究。通过对试验数据进行回归处理,得到了侧滑量与转向轮定位参数间的定量映射关系,并对其进行了回归系数、回归方程的显著性检验和失拟检验。结合汽车动力学相关理论对试验研究结果进行了分析。     

考虑动压与路面粗糙度时轮胎湿牵引性能研究

根据流体动力润滑理论,将轮胎黏性滑水问题模拟为胎面单元与路面之间的动压、挤压膜问题,同时考虑了路面粗糙度的影响,建立了轮胎胎面单元黏性滑水问题的数学模型,并进行数值求解。以矩形胎面单元为例分析了胎面单元对轮胎黏性滑水性能的影响。结果表明,轮胎的薄膜湿牵引性能与滑动速度成反比;在考虑路面粗糙度的情况下,引入了膜厚比作为轮胎的薄膜湿牵引性能衡量标准,得出湿牵引性能与路面粗糙度成正比的结论。     

In-plane Dynamics of Tires on the Road Based on an Experimentally Verified Rolling Ring Model

SUMMARY

The dynamic behavior of tires rolling on the road is predicted based on a ring model that is experimentally verified to well represent a real tire. The road contact is kinematically represented by two displacement constraints, one in radial and one in tangential direction. The displacement constraints are enforced via the receptance theory. The receptance matrix developed for the rolling tire is found to be Hermitian. Numerical results show that the natural (or eigen-) frequencies of the rolling tire with road contact are, as expected, higher than those of the tire with no contact. The influence of the rotating speed to the eigen-frquencies of the tire is also shown. Analytic expressions for the mode shapes of a rolling tire with ground contact are derived.     

用于不平路面车辆动力学仿真的轮胎模型综述

介绍了轮胎在不平路面的动力学特性。在回顾不平路面轮胎动力学模型发展的基础上，以近期的研究工作为重点，对用于不平路面车辆动力学仿真的轮胎模型进行了较为系统的介绍。概要地阐述了各种轮胎模型的建模理论、方法，并进行了分析和评述。最后，总结了不平路面轮胎力学建模的核心问题及发展方向，对不平路面车辆动力学仿真选择合适的轮胎模型给出了建议。     

某车型高速行驶方向盘摆振分析

研究高速行驶方向盘摆振影响因素与测试方法。针对某款乘用车方向盘摆振的现象进行原因分析,通过对其进行道路再现试验,测试分析轮胎至方向盘的灵敏度,可知该车对轮胎异相位的激励非常灵敏;以副车架为参考点,建立模型,通过ODS分析进一步验证摆振产生原因。该研究为高速行驶方向盘摆振问题的解决提供依据。     

表面粗糙度对冰路面上滑动轮胎摩擦牵引力影响的研究

依据能量守恒定律和冰的摩擦熔化理论，考虑冰面和轮胎胎面的表面粗糙度，建立了摩擦界面冰完全熔化条件下轮胎的牵引力预测模型。给出了预测模型中接地胎面温度的选择原则。研究表明，该模型可较好地预测不同条件下轮胎在冰路面上的摩擦牵引力，表面粗糙度的影响随车辆行驶速度的提高而增大。     

低滑移率条件下轮速传感器脉冲数相对差值的影响因素研究

通过对捷达轿车的道路试验,研究了汽车行驶速度、载荷及轮胎气压对轮速传感器脉冲数相对差值的影响。试验结果表明,当车速增大时,从动轮(或驱动轮)之间的脉冲数相对差值较小,而驱动轮与从动轮之间的相对差值较大;在正常载荷范围内,载荷对脉冲数相对差值影响较小;脉冲数相对差值与轮胎气压差值的变化近似成线性关系。进行间接轮胎气压监视系统设计时,可以利用脉冲数的相对差值监测轮胎气压的变化。     

In-plane Dynamics of Tires on the Road Based on an Experimentally Verified Rolling Ring Model

The dynamic behavior of tires rolling on the road is predicted based on a ring model that is experimentally verified to well represent a real tire. The road contact is kinematically represented by two displacement constraints, one in radial and one in tangential direction. The displacement constraints are enforced via the receptance theory. The receptance matrix developed for the rolling tire is found to be Hermitian. Numerical results show that the natural (or eigen-) frequencies of the rolling tire with road contact are, as expected, higher than those of the tire with no contact. The influence of the rotating speed to the eigen-frquencies of the tire is also shown. Analytic expressions for the mode shapes of a rolling tire with ground contact are derived.     

载重子午轮胎与路面相互作用的分析

根据全钢载重子午线轮胎12.00R20的实际结构,考虑轮胎的几何非线性、材料非线性、接触非线性以及大变形等力学特性,应用有限元的方法建立轮胎的三维模型,橡胶材料采用Yeoh模型,橡胶-帘线复合材料采用加强筋模型,并通过轮胎径向刚度的测试验证了模型的有效性.在数值模拟中分析了轮胎在一定充气压力时,在不同垂直载荷和牵引速度的作用下,与地面在接触区域的变形情况、应力分布、摩擦应力分布等滚动接触规律.结果表明,轮胎与地面接触应力分布存在明显的非均匀性,轮胎的接地面积和地面总反力随着滚动速度的升高而增大.