轻型CNG车颗粒物排放特性研究

对同一台轻型两用燃料（C N G和汽油）车使用同一批次基准天然气和基准汽油,在底盘测功机上进行NEDC ,FTP75和WLTC循环对比试验,使用CVS定容取样系统和ELPI设备分析颗粒物等排放。研究发现：3种循环中,试验车辆燃用CNG和汽油,排放颗粒物在 Dp ＝40 nm和 Dp ＝330 nm附近均出现峰值,Dp ＝40 nm处汽油峰值远高于CNG ,Dp ＝330 nm处CNG峰值略高于汽油;CNG的PN和PM的排放率随车速的升高而增大,在较低的匀速工况下增长幅度较小,高速工况下增长幅度较大;CNG在NEDC循环中排放的核态和聚集态颗粒物各占50％左右,FTP75和WLTC循环中排放的聚集态颗粒物占比高于NEDC ;CNG在NEDC循环中单位里程颗粒数和颗粒总数最多,FTP75和WLTC循环中单位里程颗粒数基本相同;WLTC循环中排放的颗粒物质量总量最多,FTP75和NEDC循环中排放的颗粒物质量总量基本相同;FTP75和WLTC循环中单位里程排放的颗粒物质量基本相同,约为N EDC循环的2倍。     

Effects of FTP-75 mode vehicle fuel economy improvement due to types of power steering system

This paper focuses on fuel economy improvement according to the type of power steering system. Usually, a conventional power steering system is directly driven by the crankshaft of the engine with a belt, known as HPS (hydraulic power steering). However, there is some inefficiency with this system at high engine speeds. To improve this inefficiency, automobile makers have developed two power steering systems: EHPS (electro-hydraulic power steering) and MDPS (motor-driven power steering) or EPS (electric powered steering). However, there has been insufficient study of effects of the type of power steering system on fuel economy. In this paper, the effect of the type of power steering system on fuel economy is studied experimentally, and calculations of the effect on vehicle fuel economy are presenting using computer simulation with AVL cruise software. The results demonstrate that a 1% vehicle fuel economy improvement can be achieved in a vehicle with an electro-hydraulic power steering system compared to a vehicle with a hydraulic power steering system. In addition, a 1.7% vehicle fuel economy improvement can be achieved using a full electric power steering system in a FTP-75 driving cycle. These results could be used to choose a power steering system.     

Influence of oxygenate content on particulate matter emission in gasoline direct injection engine

The relationship between the oxygen content in gasoline and the particulate emission (particle number and weight) was investigated. In order to study the influence of the engine configuration on the particulate emission, four vehicles were tested in which the following systems were installed: Vehicle 1 was equipped with direct injection system which uses central mounted outwardly opening injectors. Vehicle 2 and 3 used direct injection with a side mounted multihole injectors and Vehicle 4 had port fuel injection system. Methyl tert-butyl ether (MTBE) was used as the oxygen booster. The oxygen content in the gasoline was varied from 1 to 3 wt%, which corresponds with an MTBE dosage from 3.55% to 16.11%. This study used fuel that contained the same octane number with a 2% oxygen content without oxygen components, and it was used as the reference fuel in order to distinguish the effect of the oxygen content increases and the octane boosts that result from the MTBE. All vehicle tests were performed on a roller type chassis dynamometer using the New European Driving Cycle (NEDC) and Federal Test Procedure-75 (FTP-75) cycle. The experiment results demonstrate that the oxygen content increases in the gasoline reduced the particulate emission in vehicles with direct injection engines. An equivalent phenomenon was observed in a vehicle with a port fuel injection engine, but its absolute particle number was much smaller than that of the gasoline direct injection engine. The amount of reduction of the particle number in the start (cold) phase of the test cycle was significant compared with the later (hot) phase engine operation. However, particulates were emitted even though the engine was fully warmed up, especially when the engine was highly loaded. Other factors such as fuel economy or other exhaust emissions were not significantly affected by the oxygen content.     

轻型汽油车N_2O排放特性研究

选择1辆满足国Ⅴ排放标准的轻型汽油车作为试验样车,应用全流稀释排放测试系统在FTP75和US06测试循环下,对车辆在不同测试工况下的N_2O排放水平、车辆N_2O排放的影响因素以及N_2O排放随着车辆里程增加的劣化情况进行了研究。研究结果表明:FTP75循环下的N_2O排放结果高于US06循环,前者是后者的4倍左右;在冷起动阶段,由于催化剂没有达到正常的工作温度,车辆会产生较多的N_2O排放,且随着燃油硫含量的增加,车辆的N_2O排放呈现上升的趋势;随着车辆里程的不断增加,车辆的N_2O排放存在一定程度的劣化。     

Effect of regenerative braking energy on battery current balance in a parallel hybrid gasoline-electric vehicle under FTP-75 driving mode

In recent years, a hybrid electric vehicle (HEV) has been considered a successful technology. Especially, in case of a full HEV, the motor can drive the vehicle by itself at low velocity or assist the engine at high load. To improve the hybrid electric vehicle’s efficiency, a regenerative braking system is also applied to recover from kinetic energy. In this study, an experimental control apparatus was set up with a parallel hybrid electric vehicle mounted on a chassis dynamometer to measure ECU (engine control unit) and MCU (motor control unit) signals, including the current and state of charge in the battery. In order to analyze regenerative braking characteristics, user define braking driving cycle was introduced and carried out using different initial velocities and braking times. The FTP 75 driving cycle was then adapted under different initial SOC (state of charge) levels. The experiment data was analyzed in accordance with the vehicle velocity, battery current, instant SOC level, motor RPM, engine RPM, and then vehicle driving mode was decided. In case of braking driving cycle, it was observed that SOC were increased up to 1.5 % when the braking time and the velocidy were 6 second and 60 km/h, respectively. In addition, using the FTP 75 driving cycle, mode 1 was most frequently operated at SOC 65 conditions in phase 1. In phase 2, due to frequent stop-go hills, percentage of mode 1 was increase by 22 %. Eventually, despite of identity, it was shown that the characteristics of phase 3 differed from phase 1 due to the evanishment of the effects of initial SOCs.     

对某自动档车型油耗的优化研究

基于车辆静置温度和台架试验技师的操作技巧这两个噪声因子,运用DFSS对某自动档车型的节温器开启温度、换档点、怠速转速等参数进行油耗优化研究,通过模拟软件对油耗的模拟分析与实际试验结果的关联比对,不断优化分析模型,最终实车验证油耗目标的改进且结果更加稳定。     

Effect of fuel choice on nanoparticle emission factors in LPG-gasoline bi-fuel vehicles

Nanoparticle and gas-phase emission factors are presented for a liquefied petroleum gas (LPG) passenger vehicle and are compared to gasoline operation. A bi-fuel LPG-gasoline vehicle certified for use on either fuel was used as the test vehicle so that a direct comparison of the emissions could be made based on fuel choice. These values were considered along with previous studies to determine the relative change in particulate emissions due to fuel choice over a wide range of vehicles and operating conditions. The vehicle examined in this study was tested on a chassis dynamometer for both steadystate and transient conditions. Transient test cycles included the US FTP72 driving cycle, Japanese driving cycle and modified Indian driving cycle while steady-state tests were done at vehicle speeds ranging from 10–90 km/hr in various transmission gears. Exhaust particle size distributions were measured in real-time using a differential mobility spectrometer (DMS50), and particle number and particle mass emission factors were calculated. For both fuels, the majority of the particles ranged from 5 to 160 nm in terms of particle diameter, with typically more than 85% of the particles in the nucleation mode (between 5–50 nm). In most cases, the vehicle produced a greater fraction of larger (accumulation mode) particles when fuelled on LPG. Using the data in the literature as well as the data in the current study, gasoline fuel produces 4.6 times more particles in terms of number and 2.1 times more particles in terms of mass.     

浅谈新双积分法规下乘用车降油耗方案研究

乘用车燃油经济性是评价车辆性能的重要指标,通常以在一定循环行驶试验工况下,行驶100km所消耗燃油升数(单位为L/100km)作为评价指标。影响乘用车燃油经济性的因素很多,文章以公司某在研SUV为例,通过仿真及转鼓油耗测试手段,在保证车辆驾驶体验体验前提下,研究如何降低整车燃油经济性。     

CVT ratio control with consideration of CVT system loss

A modified CVT ratio map is proposed to obtain the improved fuel economy for a metal belt CVT. Since the CVT system loss, which occupies most of the drivetrain loss, depends on the engine speed, input torque, primary and secondary actuator pressure, a modified CVT ratio map is produced to realize the highest engine-CVT overall efficiency through the consideration of CVT system loss. The modified CVT ratio map is constructed with respect to the demanded vehicle power and present vehicle speed based on the steady state CVT system loss. Using the modified CVT ratio map, performance simulations are carried out using the dynamic models of the CVT powertrain. The simulation results indicate that the modified CVT ratio control provides improved engine-CVT overall system efficiency, and improves the fuel economy of the federal urban driving schedule by 4.9 percent.     

基于GT—DRIVE的整车动力性燃油经济性仿真

汽车的动力性和燃油经济性是其最基本与最重要的性能之一。为在汽车开发之初分析整车的动力性和燃油经济性,文章研究了动力性和燃油经济性的评价指标,合理选取整车参数,利用GTDRIVE软件对整车进行动力学和运动学建模与仿真计算。将仿真结果与试验结果对比,合理设置边界条件修正模型,最终得到较为精准的模型,使得在没有样车阶段,利用GT—DRIVE软件仿真可以得到整车的动力性和燃油经济性参数,能够对动力系统的匹配方案进行定量评价,为以后汽车的动力系统匹配优化提供一定的理论参考。     

Stability enhancement and fuel economy of the 4-wheel-drive hybrid electric vehicles by optimal tyre force distribution

In this paper, vehicle stability control and fuel economy for a 4-wheel-drive hybrid vehicle are investigated. The integrated controller is designed within three layers. The first layer determines the total yaw moment and total lateral force made by using an optimal controller method to follow the desired dynamic behaviour of a vehicle. The second layer determines optimum tyre force distribution in order to optimise tyre usage and find out how the tyres should share longitudinal and lateral forces to achieve a target vehicle response under the assumption that all four wheels can be independently steered, driven, and braked. In the third layer, the active steering, wheel slip, and electrical motor torque controllers are designed. In the front axle, internal combustion engine (ICE) is coupled to an electric motor (EM). The control strategy has to determine the power distribution between ICE and EM to minimise fuel consumption and allowing the vehicle to be charge sustaining. Finally, simulations performed in MATLAB/SIMULINK environment show that the proposed structure could enhance the vehicle stability and fuel economy in different manoeuvres.     

Simulation of city bus performance based on actual urban driving cycle in China

This paper establishes the simulation model of a city bus on the basis of the EQ6110 bus prototype and its experimental data. According to the actual urban driving cycle, the fuel economy and the traction performance of the EQ6110 city bus have been simulated, and factors such as the driving cycle, the loss of power to engine accessories, the gear-shifting strategy, the fuel shut-off strategy of the engine, etc., which influence on the bus’s fuel economy, are also quantitatively analyzed. Some conclusions are drawn as follows: (1) driving cycles have a great influence on the fuel economy of a city bus; (2) under the typical urban driving cycle of the public bus in China, the engine fuel shut-off strategy can save about 1 to 1.5 percent of the fuel consumption; and (3) the optimized gear-shifting rules can save 6.7 percent of the fuel consumption. Experimental results verify that the fuel economy for the EQ6110 public bus is improved by 7.2 pecent over the actual Wuhan urban driving cycle of the current public bus in China.     

Analysis of vehicle fuel efficiency and survival patterns for the prediction of total energy consumption from ground transportation in Korea

In this study, correlation between vehicle fuel efficiency and total fuel energy consumption is analyzed to support the energy consumption and greenhouse gas (GHG) emissions reduction master plan in Korea. The background and highlights of recently amended fuel economy regulations and fuel efficiency labeling standards in Korea are also introduced. 18 representative vehicle groups, classified by class, type, size, and fuel, are selected by investigating vehicle distribution statistics based on market penetration and registration data sets in order to reflect and predict total fuel energy consumption in the overall ground transportation sector in Korea. Validity of the vehicle survival patterns modeled and vehicle classification rules are confirmed by comparing national fuel energy consumption statistics to the total amount of fuel consumed by each selected representative vehicle group. The latter figures are approximated from representative number of registrations, weighted average fuel economy, and average annual distance traveled.     

混合动力汽车燃油经济性研究

应用能量分析的方法,以轿车和载货汽车为例,研究了混合动力汽车(HEV)与传统燃油发动机汽车的燃油经济性。发现按原车后备功率最大值时所对应的车速所需的驱动功率作为HEV燃油发动机功率的选择依据,节油效果最显著。当燃油驱动功率和电动驱动功率各占50%左右时,HEV轿车的经济性评价指标为原车的22.8%,HEV货车的经济性评价指标为原车的79.2%,同时又能保证动力性基本不变。结果表明,用混合动力可以有效地降低汽车的100km燃料消耗量,轿车的燃料消耗降低幅度大于货车。     

Application of a modified thermostatic control strategy to parallel mild HEV for improving fuel economy in urban driving conditions

A modified thermostatic control strategy is applied to the powertrain control of a parallel mild hybrid electric vehicle (HEV) to improve fuel economy. This strategy can improve the fuel economy of a parallel mild HEV by operating internal combustion engine (ICE) in a high-efficiency region. Thus, in this study, experiments of a parallel mild HEV were conducted to analyze the characteristics of the hybrid electric powertrain and a numerical model is developed for the vehicle. Based on the results, the thermostatic control strategy was modified and applied to the vehicle model. Also, battery protection logic by using electrochemical battery model is applied because the active usage of battery by thermostatic control strategy can damage the battery. The simulation results of the vehicle under urban driving conditions show that the thermostatic control strategy can improve the vehicle’s fuel economy by 3.7 % compared with that of the conventional strategy. The results also suggest that the trade-off between the fuel economy improvement by efficient ICE operation and the battery life reduction by active battery usage should be carefully investigated when a thermostatic control strategy is applied to a parallel mild HEV.     

轿车发动机机械损失的降低

机械损失对现代车用发动机燃料经济性的影响很大，轿车发动机因为其经常在很小的负荷率下运行，故障低机构损失的对改善其油耗和排放将更大的效果，分析了轿车发动机基本参数，零部件设计等对摩擦损失的影响，提出了降低其机械损失的若干措施。     

功率分流混合动力全速域工作模式切换规则优化

针对某功率分流混合动力汽车,探讨了既定模式转矩分配策略未知情况下全速域工作模式切换规则的优化问题。先在既定模式转矩分配策略未知的前提下,将等效燃油消耗与样本数字特征相结合,计算了不同荷电状态（SOC）值下各工作模式在所有可行工作点的基准综合燃油消耗率。以整车燃油经济性为优化目标,确定不同SOC值下所有可行工作点的最佳工作模式,进而得出基于车速、车轮端需求转矩、SOC值的优化后全速域工作模式切换规则,以满足不同工况下的工作模式选择需求。之后,不考虑模式切换过程对整车驾驶平顺性的影响,搭建了模式切换实施模型。再以4个新欧洲驾驶循环（NEDC）工况所构成的组合工况为目标行驶工况,将优化后全速域工作模式切换规则和传统基于逻辑门限的全速域工作模式切换规则分别应用于基于规则的能量管理策略,进行了整车燃油经济性仿真与台架试验验证。仿真结果表明：在不改变既定模式转矩分配策略的条件下,与基于逻辑门限的全速域工作模式切换规则情况相比,所提出的既定模式转矩分配策略未知情况下全速域工作模式切换规则优化方法至少可使整车燃油经济性提高7.33%。台架试验结果进一步表明,该优化方法至少可使整车燃油经济性提高6.17%。由此可见,所提出的既定模式转矩分配策略未知情况下全速域工作模式切换规则优化方法对整车燃油经济性具有较好的改善效果。     

基于上海市区道路行驶工况的混合动力汽车性能仿真研究

文章基于上海市区道路行驶循环进行了混合动力汽车的燃油经济性能仿真研究。具体内容包括动力部件的选型、控制策略的制定以及对混合动力汽车性能仿真结果的研究分析。在理论上阐述了改善混合动力汽车燃油经济性的方法以及混合动力汽车相对于传统燃油汽车的显著优势,为控制策略的具体制定奠定了基础。     

汽车动力性和经济性模拟计算

通过建立数学模型,设计了汽车动力性、经济性模拟计算软件,利用该软件进行了实际车型的模拟计算,所得结果与实际值相吻合。应用该软件进行了变参数计算,并分析了影响汽车动力性、经济性的主要因素,从而为汽车产品设计提供参考依据。     

四轮驱动燃料电池汽车动力系统参数匹配与优化

针对某多电机双能源四轮驱动燃料电池汽车动力参数匹配进行了研究。根据其整车结构、行驶工况以及控制策略,对动力系统参数进行初步选择,并以动力系统各部件尺寸最小为目标函数、相应参数为设计变量、整车动力性能为约束条件进行优化计算,得出动力传动系统合理的参数匹配,不仅动力性完全满足设计要求,而且经济性得到提高。