Contrasting the direct use of data from traffic radars and video-cameras with traffic simulation in the estimation of road emissions and PM hotspot analysis

This study investigates the effect of traffic volume and speed data on the simulation of vehicle emissions and hotspot analysis. Data from a microwave radar and video cameras were first used directly for emission modelling. They were then used as input to a traffic simulation model whereby vehicle drive cycles were extracted to estimate emissions. To reach this objective, hourly traffic data were collected from three periods including morning peak (6–9 am), midday (11–2 pm), and afternoon peak (3–6 pm) on a weekday (June 23, 2016) along a high-volume corridor in Toronto, Canada. Traffic volumes were detected by a single radar and two video cameras operated by the Southern Ontario Centre for Atmospheric Aerosol Research. Traffic volume and composition derived from the radar had lower accuracy than the video camera data and the radar performance varied by lane exhibiting poorer performance in the remote lanes. Radar speeds collected at a single point on the corridor had higher variability than simulated traffic speeds, and average speeds were closer after model calibration. Traffic emissions of nitrogen oxides (NOx) and particulate matter (PM₁₀ and PM_2.5) were estimated using radar data as well as using simulated traffic based on various speed aggregation methods. Our results illustrate the range of emission estimates (NO_x: 4.0–27.0 g; PM₁₀: 0.3–4.8 g; PM_2.5: 0.2–1.3 g) for the corridor. The estimates based on radar speeds were at least three times lower than emissions derived from simulated vehicle trajectories. Finally, the PM₁₀ and PM_2.5 near-road concentrations derived from emissions based on simulated speeds were two or three times higher than concentrations based on emissions derived using radar data. Our findings are relevant for project-level emission inventories and PM hot-spot analysis; caution must be exercised when using raw radar data for emission modeling purposes.     

Evaluating effects of traffic and vehicle characteristics on vehicular emissions near traffic intersections

Urban air quality is generally poor at traffic intersections due to variations in vehicles’ speeds as they approach and leave. This paper examines the effect of traffic, vehicle and road characteristics on vehicular emissions with a view to understand a link between emissions and the most likely influencing and measurable characteristics. It demonstrates the relationships of traffic, vehicle and intersection characteristics with vehicular exhaust emissions and reviews the traffic flow and emission models. Most studies have found that vehicular exhaust emissions near traffic intersections are largely dependent on fleet speed, deceleration speed, queuing time in idle mode with a red signal time, acceleration speed, queue length, traffic-flow rate and ambient conditions. The vehicular composition also affects emissions. These parameters can be quantified and incorporated into the emission models. There is no validated methodology to quantify some non-measurable parameters such as driving behaviour, pedestrian activity, and road conditions     

The significant impacts on traffic and emissions of ferrying children to school in Beijing

After having implemented numerous regulations, e.g., coercive policies on vehicle use and purchase, it is becoming increasingly difficult to find further potential to control vehicle emissions in Beijing, as the air quality is still poor. This research provides a different approach for policy-makers to reduce vehicle emissions by managing demand. We found that parents ferrying their children to and from school is an important but long-neglected contributor to traffic congestion and vehicle emissions. This phenomenon is very common in China because of the social culture. In this research, parallel tests during both the school season and the non-school season were adopted, and emissions in both seasons were calculated based on travel demand and emission models. The results revealed that emissions factors (in g/km) for criteria pollutants and CO₂ increased by over 10% during rush hours during the school season due to traffic condition deterioration compared with non-school season. Daily HC, CO, NO_x, PM and CO₂ emissions from the passenger car fleet were 8.3%, 7.8%, 6.4%, 6.3% and 6.5% higher compared with those during the non-school season, respectively. These differences are greater than the total vehicular emission reduction by other control measures in 2014 in Beijing. For policy makers, providing safe and efficient ways to ferry children would be a useful and harmonious strategy for future vehicle emission control.     

Simulating the air quality impacts of traffic calming schemes in a dense urban neighborhood

In this study, the effects of isolated traffic calming measures and area-wide calming schemes on air quality in a dense neighborhood were estimated using a combination of microscopic traffic simulation, emission, and dispersion modeling. Results indicated that traffic calming measures did not have as large an effect on nitrogen dioxide (NO₂) concentrations as the effect observed on nitrogen oxide (NO_x) emissions. Changes in emissions resulted in highly disproportional changes in pollutant levels due to daily meteorological conditions, road geometry and orientation with respect to the wind. Average NO₂ levels increased between 0.1% and 10% with respect to the base-case while changes in NO_x emissions varied between 5% and 160%. Moreover, higher wind speeds decreased NO₂ concentrations on both sides of the roadway. Among the traffic calming measures, speed bumps produced the highest increases in NO₂ levels.     

Urban real-world driving traffic emissions during interruption and congestion

On-road emissions from urban traffic during interrupted and congested flow conditions are too high as compared to free-flow condition and often influenced by accelerating and decelerating speed due to frequent stop-and-go. In this study, we measured emissions from passenger cars and auto-rickshaws during peak and off-peak hours and analyzed according to different mileages with the instantaneous speed and acceleration for interrupted and congested traffic conditions. It was found that during flow, several short-events lasting over fractions of a second each lead to a sharp increase in pollutant emissions, indicating episodic conditions. The emission levels are sensitive to frequency and intensity of acceleration and deceleration, in accordance with the traffic-flow patterns and speed, besides mileages. Further, congestion conditions occur during both peak and off-peak hours, but last for different durations. The results are important in the sense that instantaneous estimates of pollutant emissions are necessary for the assessment of air quality in urban centers and for an effective traffic management plan.     

Impact of horizontal geometric design of two-lane rural roads on vehicle co2 emissions

In 2014, highway vehicles accounted for 72.8% of all Greenhouse Gases emissions from transportation in Europe. In the United States (US), emissions follow a similar trend. Although many initiatives try to mitigate emissions by focusing on traffic operations, little is known about the relationship between emissions and road design. It is feasible that some designs may increase average flow speed and reduce accelerations, consequently minimizing emissions.This study aims to evaluate the impact of road horizontal alignment on CO₂ emissions produced by passenger cars using a new methodology based on naturalistic data collection. Individual continuous speed profiles were collected from actual drivers along eleven two-lane rural road sections that were divided into 29 homogeneous road segments. The CO₂ emission rate for each homogeneous road segment was estimated as the average of CO₂ emission rates of all vehicles driving, estimated by applying the VT-Micro model.The analysis concluded that CO₂ emission rates increase with the Curvature Change Rate. Smooth road segments normally allowed drivers to reach higher speeds and maintain them with fewer accelerations. Additionally, smother segments required less time to cover the same distance, so emissions per length were lower. It was also observed that low mean speeds produce high CO₂ emission rates and they increase even more on roads with high speed dispersions.Based on this data, several regression models were calibrated for different vehicle types to estimate CO₂ emissions on a specific road segment. These results could be used to incorporate sustainability principles to highway geometric design.     

Accounting for traffic speed dynamics when calculating COPERT and PHEM pollutant emissions at the urban scale

Coupling a traffic microsimulation with an emission model is a means of assessing fuel consumptions and pollutant emissions at the urban scale. Dealing with congested states requires the efficient capture of traffic dynamics and their conditioning for the emission model. Two emission models are investigated here: COPERT IV and PHEM v11. Emission calculations were performed at road segments over 6 min periods for an area of Paris covering 3 km². The resulting network fuel consumption (FC) and nitrogen oxide (NOx) emissions are then compared. This article investigates: (i) the sensitivity of COPERT to the mean speed definition, and (ii) how COPERT emission functions can be adapted to cope with vehicle dynamics related to congestion. In addition, emissions are evaluated using detailed traffic output (vehicle trajectories) paired with the instantaneous emission model, PHEM.COPERT emissions are very sensitive to mean speed definition. Using a degraded speed definition leads to an underestimation ranging from −13% to −25% for fuel consumption during congested periods (from −17% to −36% respectively for NOx emissions). Including speed distribution with COPERT leads to higher emissions, especially under congested conditions (+13% for FC and +16% for NOx). Finally, both these implementations are compared to the instantaneous modeling chain results. Performance indicators are introduced to quantify the sensitivity of the coupling to traffic dynamics. Using speed distributions, performance indicators are more or less doubled compared to traditional implementation, but remain lower than when relying on trajectories paired with the PHEM emission model.     

A field evaluation case study of the environmental and energy impacts of traffic calming

This study quantifies the energy and environmental impact of a selection of traffic calming measures using a combination of second-by-second floating-car global positioning system data and microscopic energy and emission models. It finds that traffic calming may result in negative impacts on vehicle fuel consumption and emission rates if drivers exert aggressive acceleration levels to speed up to their journeys. Consequently by eliminating sharp acceleration maneuvers significant savings in vehicle fuel consumption and emission rates are achievable through driver education. The study also demonstrates that high emitting vehicles produce CO emissions that are up to 25 times higher than normal vehicle emission levels while low emitting vehicles produce emissions that are 15–35% of normal vehicles. The relative increases in vehicle fuel consumption and emission levels associated with the sample traffic calming measures are consistent and similar for normal, low, and high emitting vehicles.     

Impacts of freeway accidents on CO2 emissions: A case study for Orange County,California, US

Traffic congestion caused by traffic accidents contributes to CO₂ emissions. Generally, more efficient and prompt responses to accidents lead to reduced traffic congestion as well as CO₂ emissions. Here we assess the CO₂ emissions impacts of freeway accidents, applies an existing model to capture spatio-temporally congested regions caused by freeway accidents. A case study for the assessment of CO₂ emissions impacts of based on the results from the model is presented.     

Spatiotemporal intersection control in a connected and automated vehicle environment

Current research on traffic control has focused on the optimization of either traffic signals or vehicle trajectories. With the rapid development of connected and automated vehicle (CAV) technologies, vehicles equipped with dedicated short-range communications (DSRC) can communicate not only with other CAVs but also with infrastructure. Joint control of vehicle trajectories and traffic signals becomes feasible and may achieve greater benefits regarding system efficiency and environmental sustainability. Traffic control framework is expected to be extended from one dimension (either spatial or temporal) to two dimensions (spatiotemporal). This paper investigates a joint control framework for isolated intersections. The control framework is modeled as a two-stage optimization problem with signal optimization at the first stage and vehicle trajectory control at the second stage. The signal optimization is modeled as a dynamic programming (DP) problem with the objective to minimize vehicle delay. Optimal control theory is applied to the vehicle trajectory control problem with the objective to minimize fuel consumption and emissions. A simplified objective function is adopted to get analytical solutions to the optimal control problem so that the two-stage model is solved efficiently. Simulation results show that the proposed joint control framework is able to reduce both vehicle delay and emissions under a variety of demand levels compared to fixed-time and adaptive signal control when vehicle trajectories are not optimized. The reduced vehicle delay and CO₂ emissions can be as much as 24.0% and 13.8%, respectively for a simple two-phase intersection. Sensitivity analysis suggests that maximum acceleration and deceleration rates have a significant impact on the performance regarding both vehicle delay and emission reduction. Further extension to a full eight-phase intersection shows a similar pattern of delay and emission reduction by the joint control framework.     

Simulating the environmental effects of isolated and area-wide traffic calming schemes using traffic simulation and microscopic emission modeling

This study focuses on the development of a microscopic traffic simulation and emission modeling system which aims at quantifying the effects of different types of traffic calming measures on vehicle emissions both at a link-level and at a network-level. It also investigates the effects of isolated traffic-calming measures at a corridor level and area-wide calming schemes, using a scenario analysis. Our study is set in Montreal, Canada where a traffic simulation model for a dense urban neighborhood is extended with capabilities for microscopic emission estimation. The results indicate that on average, isolated calming measures increase carbon dioxide (CO₂), carbon monoxide (CO), and nitrogen oxides (NO_x) emissions by 1.5, 0.3, and 1.5 %, respectively across the entire network. Area-wide schemes result in a percentage increase of 3.8 % for CO₂, 1.2 % for CO, and 2.2 % for NO_x across the entire network. Along specific corridors where traffic calming measures were simulated, increases in emissions of up to 83 % were observed. We also account for the effect of different measures on traffic volumes and observe moderate decreases in areas that have undergone traffic calming. In spite of traffic flow reductions, total emissions do increase.     

Impact of public transport and non-motorized transport infrastructure on travel mode shares,energy, emissions and safety: Case of Indian cities

Current modal share in Indian cities is in favor of non-motorized transport (NMT) and public transport (PT), however historical trends shows decline in its use. Existing NMT and PT infrastructure in Indian cities is of poor quality resulting in increasing risk from road traffic crashes to these users. It is therefore likely that the current NMT and PT users will shift to personal motorized vehicles (PMV) as and when they can afford it. Share of NMT and PT users can be retained and possibly increased if safe and convenient facilities for them are created. This shall also have impact on reducing environment impacts of transport system.We have studied travel behavior of three medium size cities – Udaipur, Rajkot and Vishakhapatnam. Later the impact of improving built environment and infrastructure on travel mode shares, fuel consumption, emission levels and traffic safety in Rajkot and Vishakhapatnam are analyzed. For the purpose three scenarios are developed – improving only NMT infrastructure, improving only bus infrastructure and improving both NMT and bus infrastructure.The study shows the strong role of NMT infrastructure in both cities despite geographical dissimilarities. The scenario analysis shows maximum reduction in CO₂ emissions is achieved when both PT and NMT infrastructure are improved. Improvement in safety indicator is highest in this scenario. Improving only PT infrastructure may have marginal effect on overall reduction of CO₂ emissions and adverse effects on traffic safety. NMT infrastructure is crucial for maintaining the travel mode shares in favor of PT and NMT in future.     

A velocity and payload dependent emission model for heavy-duty road freight transportation

The paper develops a forecasting model of emissions from traffic flows embracing the dynamics of driving behavior due to variations in payload. To measure of emissions at the level of individual vehicles under varying payloads a portable emission measurement system is used. This paper reports on a model based on data at the level of individual vehicles for a representative road trajectory. The model aggregates the data to the level of a homogeneous flow dependent of velocity and specific power, which is dependent on payload weight. We find a lean specification for the model that provides emission factors for CO₂, NO_x, HC, CO, and NO₂. The results indicate that, in comparison with earlier models, NO_x emissions in particular tend to be underestimated.     

An evaluation framework for traffic calming measures in residential areas

The paper evaluates the effectiveness of various traffic calming measures from the perspectives of traffic performance and safety, and environmental and public health impacts. The proposed framework was applied to four calming measures – two types of speed humps, speed tables, and chicanes – to demonstrate its usefulness and applicability. A field experiment using probe vehicles equipped with global positioning system devices was conducted to obtain vehicle trajectory data for use in more realistic simulations. In addition, a recently developed vehicle emissions model was used for more accurate evaluation of environmental and public health impacts. The results show that chicane is better than the other types of traffic calming measures considered, except in terms of vehicle emissions.     

A new probability statistical model for traffic noise prediction on free flow roads and control flow roads

A new traffic noise prediction approach based on a probability distribution model of vehicle noise emissions and achieved by Monte Carlo simulation is proposed in this paper. The probability distributions of the noise emissions of three types of vehicles are obtained using an experimental method. On this basis, a new probability statistical model for traffic noise prediction on free flow roads and control flow roads is established. The accuracy of the probability statistical model is verified by means of a comparison with the measured data, which has shown that the calculated results of L_eq, L₁₀, L₅₀, L₉₀, and the probability distribution of noise level occurrence agree well with the measurements. The results demonstrate that the new method can avoid the complicated process of traffic flow simulation but still maintain high accuracy for the traffic noise prediction.     

Assessing carbon emissions from road transport through traffic flow estimators

Carbon emissions from road transport are one of the main issues related to modern transport planning. To address them adequately, the acquisition of reliable data about traffic flow is an essential prerequisite. However, the large quantity and the heterogeneity of available information often cause problems; missing or incomplete data are one of the most critical aspects. This paper discusses how technology handles imperfect information in order to obtain more accurate quantification of CO₂ emissions. First, an analysis of single estimators and combination models is provided, highlighting their main characteristics. Then, the TANINO model (Tool for the Analysis of Non-conservative Carbon Emissions In TraNspOrt) is presented, jointly developed at the University of Seville and at the IUAV University of Venice. It consists of two different modules: the first is a combination model that optimizes the results of three traffic flow single estimators, while the second is a macro-model of carbon evaluation, which takes into account road infrastructure, vehicle type and traffic conditions. TANINO is then tested to calculate CO₂ emissions along the ring road of the Spanish city of Seville, showing its more efficient performance, compared to the single estimators normally adopted for such aims. Transport planning can benefit from the adequate knowledge of traffic flows and related CO₂ emissions, since it allows a more reliable monitoring of the progresses granted by specific carbon policies.     

Analyzing spatiotemporal traffic line source emissions based on massive didi online car-hailing service data

Nowadays, the massive car-hailing data has become a popular source for analyzing traffic operation and road congestion status, which unfortunately has seldom been extended to capture detailed on-road traffic emissions. This study aims to investigate the relationship between road traffic emissions and the related built environment factors, as well as land uses. The Computer Program to Calculate Emissions from Road Transport (COPERT) model from European Environment Agency (EEA) was introduced to estimate the 24-h NOx emission pattern of road segments with the parameters extracted from Didi massive trajectory data. Then, the temporal Fuzzy C-Means (FCM) Clustering was used to classify road segments based on the 24-h emission rates, while Geographical Detector and MORAN’s I were introduced to verify the impact of built environment on line source emissions and the similarity of emissions generated from the nearby road segments. As a result, the spatial autoregressive moving average (SARMA) regression model was incorporated to assess the impact of selected built environment factors on the road segment emission rate based on the probabilistic results from FCM. It was found that short road length, being close to city center, high density of bus stations, more ramps nearby and high proportion of residential or commercial land would substantially increase the emission rate. Finally, the 24-h atmospheric NO₂ concentrations were obtained from the environmental monitor stations, to calculate the time variational trend by comparing with the line source traffic emissions, which to some extent explains the contribution of on-road traffic to the overall atmospheric pollution. Result of this study could guide urban planning, so as to avoid transportation related built environment attributes which may contribute to serious atmospheric environment pollutions.     

Forecasting road traffic conditions using a context-based random forest algorithm

With the ability to accurately forecast road traffic conditions several hours, days and even months ahead of time, both travellers and network managers can take pro-active measures to minimise congestion, saving time, money and emissions. This study evaluates a previously developed random forest algorithm, RoadCast, which was designed to achieve this task. RoadCast incorporates contexts using machine learning to forecast more accurately contexts such as public holidays, sporting events and school term dates. This paper evaluates the potential of RoadCast as a traffic forecasting algorithm for use in Intelligent Transport System applications. Tests are undertaken using a number of different forecast horizons and varying amounts of training data, and an implementation procedure is recommended.     

Metropolitan sprawl measurement and its impacts on commuting trips and road emissions

This study measures urban form as indicators of metropolitan sprawl and explores its impact on commuting trips and NO_x and CO₂ emissions from road traffic in all metropolitan statistical areas (MSAs) and four groups’ MSAs separated by population in the continental United States. Encompassing all MSAs, the study adds the accessibility factor to four existing factors: density, land use mix, centeredness, and street connectivity. The study establishes multivariate regression models between urban form, commuting trips, and emissions from road traffic while controlling for socioeconomic conditions. The study shows that urban form index and five urban form factors have a statistically significant association with commuting trips, NO_x and CO₂ emissions from road traffic. In four MSA groups as determined by MSA population size, higher values of urban form factors (i.e., lower sprawl) are statistically associated with more walking commuters. On the other hand, higher values of urban form factors are associated with fewer commuting vehicles per household in large MSAs with the moderate effect, a lower average commuting drive time in medium and small MSAs, and more commuters using public transportation in medium and large MSAs. This study provides an urban form index covering all metropolitan areas in the continental United States by adding another urban form factor, and the findings show that urban form factors have different effects on mode choices, drive time, and emission from road traffic depending on the MSA population size.     

Temporal and spatial variation in allocating annual traffic activity across an urban region and implications for air quality assessments

Patterns of traffic activity, including changes in the volume and speed of vehicles, vary over time and across urban areas and can substantially affect vehicle emissions of air pollutants. Time-resolved activity at the street scale typically is derived using temporal allocation factors (TAFs) that allow the development of emissions inventories needed to predict concentrations of traffic-related air pollutants. This study examines the spatial and temporal variation of TAFs, and characterizes prediction errors resulting from their use. Methods are presented to estimate TAFs and their spatial and temporal variability and used to analyze total, commercial and non-commercial traffic in the Detroit, Michigan, U.S. metropolitan area. The variability of total volume estimates, quantified by the coefficient of variation (COV) representing the percentage departure from expected hourly volume, was 21%, 33%, 24% and 33% for weekdays, Saturdays, Sundays and holidays, respectively. Prediction errors mostly resulted from hour-to-hour variability on weekdays and Saturdays, and from day-to-day variability on Sundays and holidays. Spatial variability was limited across the study roads, most of which were large freeways. Commercial traffic had different temporal patterns and greater variability than non-commercial vehicle traffic, e.g., the weekday variability of hourly commercial volume was 28%. The results indicate that TAFs for a metropolitan region can provide reasonably accurate estimates of hourly vehicle volume on major roads. While vehicle volume is only one of many factors that govern on-road emission rates, air quality analyses would be strengthened by incorporating information regarding the uncertainty and variability of traffic activity.