共查询到20条相似文献,搜索用时 62 毫秒
1.
HEV控制器硬件在环仿真平台的研究与开发 总被引:3,自引:0,他引:3
针对控制器传统开发方法中存在的局限性以及混合动力汽车动力传动系统控制的复杂性,应用控制系统现代开发技术,为某型混合动力客车多能源动力总成控制器开发了硬件在环仿真测试平台,该平台包括实时硬件和系统模型、信号调理电路等,并利用它对控制器进行了仿真测试。仿真测试结果与试验结果说明,所开发平台模型的精度基本能够满足仿真测试要求。控制器的环境试验和在EMC试验中的成功应用以及控制器在车上的正常运行,验证了在混合动力汽车多能源动力总成控制器的开发过程中采用自行开发硬件在环仿真测试平台这一技术方案的可行性。 相似文献
2.
并联式混合动力电动汽车动力总成控制器硬件在环仿真 总被引:3,自引:1,他引:3
通过对EQ6110并联式混合动力城市客车的动力总成系统结构和控制系统的分析,研制开发了用于并联式混合动力电动汽车(PHEV)的动力总成控制器设计开发的硬件在环仿真系统;详细介绍了动力总成各个部件仿真模型的建立,包括发动机模型、电机模型、动力电池模型以及传动系统模型等;通过Matlab/Simulink的建模,运用dSPACE实时计算系统成功地构建了PHEV多能源动力总成控制器的硬件在环仿真系统;最后进行了PHEV动力总成控制器硬件在环仿真的测试试验研究。 相似文献
3.
4.
5.
6.
混合动力汽车动力总成试验台研究 总被引:12,自引:2,他引:12
基于混合动力汽车有串联、并联和混联等多种结构形式的特点,提出以模块化设计思想来搭建混合动力汽车动力总成试验台的方法,从而达到了在比较短的时间内、以尽量小的改动适应不同混合动力汽车动力总成结构形式组合需要的目标。根据研究需要,首先完成了混合动力汽车动力总成试验台并联形式的建设,并利用该试验台对所研制的混合动力城市客车多能源动力总成控制器进行了初步调试,验证了该控制器的软硬件设计和并联电动助力型控制策略。同时,所完成的发动机台架试验和电机台架试验也充分证明了试验台模块化设计思想的可行性和有效性。 相似文献
7.
8.
9.
10.
4FCEV动力性能的仿真FCEV的多能源动力系统的控制相当复杂,利用计算机技术和仿真软件,可对FCEV的整车结构模型、动力性能、动力匹配、动力组合和道路工况等进行模拟和仿真,能最佳地确定多能源动力总成中各种不同驱动模式所采取的控制策略,这就大大地加速了FCEV的研究、开发、试 相似文献
11.
12.
《Vehicle System Dynamics: International Journal of Vehicle Mechanics and Mobility》2012,50(4):573-596
An existing driver–vehicle model with neuromuscular dynamics is improved in the areas of cognitive delay, intrinsic muscle dynamics and alpha–gamma co-activation. The model is used to investigate the influence of steering torque feedback and neuromuscular dynamics on the vehicle response to lateral force disturbances. When steering torque feedback is present, it is found that the longitudinal position of the lateral disturbance has a significant influence on whether the driver’s reflex response reinforces or attenuates the effect of the disturbance. The response to angle and torque overlay inputs to the steering system is also investigated. The presence of the steering torque feedback reduced the disturbing effect of torque overlay and angle overlay inputs. Reflex action reduced the disturbing effect of a torque overlay input, but increased the disturbing effect of an angle overlay input. Experiments on a driving simulator showed that measured handwheel angle response to an angle overlay input was consistent with the response predicted by the model with reflex action. However, there was significant intra- and inter-subject variability. The results highlight the significance of a driver’s neuromuscular dynamics in determining the vehicle response to disturbances. 相似文献
13.
预应力曲线箱梁和异形箱梁的研究 总被引:7,自引:0,他引:7
近年来 ,国内外学者对曲线箱梁和异形箱梁的静力分析理论和计算方法作过大量的研究 ,但这些理论和方法在某种程度上都存在着一定的局限性 ,特别是在实际设计工作中 ,运用起来不能得心应手。为此本文在综合前人已取得经验下 ,针对桥梁结构设计中分析曲线箱梁、异形箱梁 ,经常遇到的难题进行了研究 ,建立一个较为完善的理论和方法 ,编制了等参元空间分析程序。在实际工程中进行实桥试验 ,验证了本文理论和方法的正确性。本文的研究工作更准确描述了箱梁的荷载响应 ,为设计人员提供直观的设计依据。对曲线箱梁和异形箱梁受力特性有了更一步的理解 ,并提出了新的见解 相似文献
14.
SMA是沥青码蹄脂碎石(Stone Matrix Asphal)的缩写,是一种以沥青结合料与少量的纤维稳定剂、细集料,以及较多的填料(矿粉)组成的沥青玛蹄脂,填充于间断级配粗集料骨架间隙中组成一体所形成的沥青混合料,简称SMA。该文介绍了SMA在上海的应用及其施工技术。 相似文献
15.
混凝土的推广使用已有一个世纪,目前在现代工程建设中仍占有重要的地位。而在今天,混凝土的裂缝较为普遍,在桥梁工程中裂缝几乎无所不在,尽管我们在施工中采取各种各样的措施,但收效甚微,裂缝仍然时有出现。该文指出,究其原因,人们对混凝土温度变化所产生的应力注意不够是其中之一,尤其是大体积混凝土。对此,温度应力与温度控制具有重要的意义。 相似文献
16.
利用AVL公司开发的BOOST软件可宏观地描述发动机的热力学过程且优化发动机的性能,而AVL的CRUISE软件可调用BOOST建立的发动机模型.在进行道路循环工况的仿真时,须对发动机全部工况点进行准确的标定.文中采用BOOST开发了发动机的仿真模型.通过调整节气门开度和燃烧模型参数,标定了发动机在多个转速和负荷点的转矩、功率和油耗,较好地模拟了发动机的动力性和经济性.最后基于ECE循环工况,将此模型与CRUISE进行联合仿真,分析了发动机瞬态工况的动力性、油耗和NO_x排放等参数. 相似文献
17.
J. R. Serrano F. J. Arnau V. Dolz A. Tiseira M. Lejeune N. Auffret 《International Journal of Automotive Technology》2008,9(3):277-288
This article presents a two-stage turbocharged heavy-duty diesel (HDD) engine designed to fulfil the US2007 anti-pollution
directive. This directive imposes very restrictive limits on the NOx and particle emissions of HDD engines. In this work,
the possibility of combining particle traps in the exhaust line to reduce soot emissions with very high EGR rates to reduce
NOx emissions is considered. This new generation engine implements two-stage turbocharging in order to improve the bsfc when
the engine is working on steady conditions as well as to optimize the engine transient response. After carrying out the tests,
the results were analyzed and the engine settings were adjusted to maximise its behaviour and minimise pollutant emissions.
NOx and soot emission peaks were also analyzed at engine transient conditions in order to keep them under certain levels,
and thus maintain the overall pollutant emissions to a level that is as low as possible. In summary, a double-stage turbocharging
configuration can greatly improve engine driveability (between 23% and 36% depending on engine speed), while reducing NOx
emissions during transient evolution without increasing opacity peaks beyond the stated limits. 相似文献
18.
19.
该文从研究超薄磨耗层的级配的选择入手,简单分析了超薄磨耗层的结构特点和强度形成机理,给出了几种国内外常用的超薄磨耗层级配范围,并提出了将SAC-10做为其研究的设计级配。在研究超薄磨耗层沥青混合料配合比设计的基础上,通过对SAC-10沥青混合料的马歇尔试验,确定了该沥青混合料的矿料级配和最佳沥青含量。最后采用车辙试验、浸水马歇尔和冻融劈裂试验及小梁弯曲试验等一系列试验,检测超薄磨耗层沥青混合料的各项路用性能,为在实际工程中的应用提供理论依据。 相似文献