基于广义切线模量理论的铝合金加筋板结构轴压极限强度分析

研究铝合金加筋板结构的极限强度,有利于充分发挥铝合金材料的强度潜力和结构的后屈曲承载能力。本文将广义切线模量理论应用于铝合金加筋板结构的轴压极限强度计算,并推导了适用于加筋板的协调参数、极限弯矩系数及结构系数等相关参数的解析算式,建立了铝合金加筋板结构的强度利用率函数,从而得到结构的极限强度,进一步完善了广义切线模量理论在加筋板结构极限强度研究领域的应用。通过将广义切线模量法计算结果与经验公式、有限元计算结果进行比较,验证了其适用性与可靠性,可用于工程分析计算。     

复合材料船体纵向极限强度可靠性分析

把船体甲板或船底板结构视为是一系列加筋板单元的组合，然后利用复合材料梁柱理论计算船体加筋板单元构件的极限承载能力，最后用Smith法计算复合材料船体的极限承载能力。由于复合材料船体纵向极限强度的极限状态方程不能简单地用船体各参数显式表达，故将近年发展起来的响应面法与JC法相结合，对复合材料船体纵向极限强度进行了可靠性分析。并讨论了影响船体纵向极限强度可靠性各变量的敏感性。     

基于J积分的含裂纹加筋板在单轴拉伸载荷下的极限强度计算

为研究含裂纹加筋板的极限拉伸强度,本文建立一系列不同长细比、不同裂纹长度、不同裂纹位置的含裂纹加筋板有限元模型,并基于J积分理论对其在单轴拉伸载荷下的极限强度进行了计算。结果发现含裂纹加筋板极限拉伸强度随加筋板长细比的增大略有减小,但减小的程度并不明显;含裂纹加筋板极限拉伸强度随裂纹长度的增大而减小,且减小的幅度逐渐增大;加强筋上的裂纹对含裂纹加筋板极限强度的影响小于底板上的裂纹,而裂纹同时出现在底板和加强筋上时对含裂纹加筋板极限拉伸强度的影响最大。表明含贯穿型裂纹的加筋板在单轴拉伸载荷下的剩余强度对加筋板长细比不敏感,而对裂纹长度较为敏感。     

Comparisons of calculations with experiments on the ultimate strength of wide stiffened panels

Five specimens of wide stiffened panel with four stiffeners under axial compression until collapse are studied with a nonlinear finite element analysis and Common Structural Rules to compare with the experimental results. The stiffened panel models have two longitudinal bays to produce reasonable boundary condition at the end of edges. Tension tests have been conducted to obtain the material properties of the steel that are used in the finite element analysis. Three boundary condition configurations are adopted to investigate their influence on the collapse behaviour of the stiffened panels. A displacement transducer was used to measure the initial geometrical imperfections of the stiffened plates. The collapse behaviour of the stiffened panels is analysed in finite element analysis with the measured initial imperfections and with nominal imperfections. An equivalent initial imperfection is validated for the ultimate strength of stiffened panel under compressive load until collapse for the panels under consideration. With the same imperfection amplitude, the shape of the column-type initial deflection of stiffeners affects significantly the collapse shape, but only slightly the ultimate strength and the mode of collapse of the stiffened panels. The 1/2 + 1 + 1/2 bays model with restrained boundary condition BC3 gives an adequate FE modelling and is possible to be fabricated in experiment.     

Influence of boundary conditions on the collapse behaviour of stiffened panels under combined loads

A series of finite element analyses are conducted to investigate the influence of boundary conditions and geometry of the model on the predicted collapse behaviour of stiffened panels. Periodic and symmetric boundary conditions in the longitudinal direction are used to calculate the ultimate strength of stiffened panels under combined biaxial thrust and lateral pressure. The calculated ultimate strength of stiffened panels are compared with those by different FEM (finite element method) code and are assessed. The periodic boundary condition in the longitudinal direction for two spans or bays model provides an appropriate modelling to a continuous stiffened panel and can consider both odd and even number of half waves and thus, is considered to introduce the smaller model uncertainty for the analysis of a continuous stiffened panel.     

加筋板极限压缩强度的对传神经网络计算

基于大量实验结果,提出了用对传神经网络（ＣＰＮ）计算加筋板极限强度的方法。与近年 来提出的双参数拟合多项式比较,ＣＰＮ可考虑更多的设计参数,并充分利用实验数据,因此拟 合精度更高。     

Prediction of hull girder moment-carrying capacity using kinematic displacement theory

The hull girder moment capacity of a very large crude oil carrier (VLCC) called Energy Concentration (EC), for which many benchmark studies have been carried out using the simple progressive collapse method (SPCM), is predicted. In this study, three approaches are used to represent the load-shortening behavior, so-called average compressive strength, of a stiffened panel, comprising the hull section: 1) kinematic displacement theory (KDT); 2) nonlinear finite element analysis (FEA); and 3) simple formulas in the common structural rule (CSR) for tankers. Load-shortening curves for various kinds of stiffened panels in EC are compared for five different scenarios with variations of load-shortening approaches and initial imperfections. In order to verify the effect of load-shortening on the prediction accuracy of the hull girder moment-carrying capacity, load-shortening curves are imported into an SPCM-based in-house program called Ultimate Moment Analysis of Damaged Ships (UMADS). Comparison of the hull girder ultimate strength for general heeling conditions, including hogging and sagging conditions, reveals that the load-shortening curves significantly affect the hull girder moment-carrying capacities. Based on our comparison of these capacities with other benchmark results, it is concluded that nonlinear FEA provided the most conservative results, KDT provided the second most conservative results, and the CSR formulas predicted the upper bound.     

初始缺陷对加筋板结构极限强度的影响研究

采用非线性有限元软件Ansys研究包含3种初始缺陷加筋板结构在单轴压缩载荷作用下极限强度的变化趋势,即初始变形、残余应力和凹陷.以单筋单跨加筋板模型为研究对象,考虑初始变形,不同半径及不同速度的撞击球所形成的凹陷及残余应力对加筋板极限强度的影响.结果表明,初始缺陷的存在降低了结构的极限承载力,而且缺陷的叠加作用比单独缺陷存在时对结构极限强度的影响大;加筋板的极限强度随着凹陷深度的加深而减小;3种初始缺陷中,残余应力相对于初始变形和凹陷对结构极限强度的削弱影响更大.     

Statistical properties of bulk carrier longitudinal strength

The paper focuses on time-variant longitudinal strength of bulk carriers under corrosion wastage, applying both Taylor series expansion method and Monte Carlo simulation. Hull girder section modulus and ultimate bending moment capacity are determined, by classical beam theory and the commonly applied incremental-iterative approach, respectively. Two main aspects are fully discussed and investigated, according to the final recommendations of last ISSC Report. The former regards the covariance between annual corrosion rates of individual structural members, commonly assumed as uncorrelated. Really, as it is conceivable that a certain correlation exists, three different cases are investigated: uncorrelated variables, fully correlated variables, full correlation between structural members belonging to the same category of compartments. The latter investigates the probability density function of both hull girder section modulus and ultimate bending capacity, because the Central Limit Theorem cannot be applied when correlation among random variables exists. Finally, as a test example, the bulk carrier section, presented in the last ISSC benchmark study, is analysed.     

Patran的PCL语言在板格和加筋板极限强度计算中的运用

用Fortran编写程序生成Patran的.ses文件,可将任意指定的初始挠度施加到要计算分析极限强度的光板和加筋板结构模型中去.具体分析6块光板和4块加筋板结构的极限强度,计算结果表明,该方法可以模拟任意复杂的变形形式,从而更加准确地计算和评估加筋板结构的极限强度.     

含裂纹加筋板在压缩载荷下的剩余极限强度试验研究

在老龄化引起的船舶结构安全性问题中,裂纹损伤是结构强度衰减的一个重要因素。文章采用逐步加载法对含裂纹损伤的加筋板压缩剩余极限强度进行试验研究。设计六种典型的穿透裂纹损伤加筋板,对损伤试件进行轴向压缩试验。通过改变裂纹尺寸、位置及倾角参数并根据试验观测结果,探讨了不同裂纹参数下加筋板的屈曲破坏特点和对剩余极限强度影响。试验结果表明,不同的裂纹长度以及裂纹位置改变加筋板结构承载力的分布,影响结构应力应变场,进而改变其失效崩溃模式;倾角为45°的裂纹相对于垂直于加筋的裂纹对加筋板结构的剩余极限强度影响较小,此外初始缺陷对结构的剩余极限强度的影响也不容忽视。     

加筋板格高级屈曲分析技术研究及软件开发

文章给出了基于弹性大挠度理论和刚塑性分析的加筋板格高级屈曲分析方法(EPM),该方法包括五种失效模式,即正交加筋板格整体屈曲、纵向加筋子板格整体屈曲、纵向加筋和带板的局部屈曲或屈服、纵向加筋的侧倾以及全部屈服,可以考虑初始挠度和残余应力的影响以及双向压缩和侧向载荷的联合作用。以EPM方法为核心开发了加筋板格高级屈曲分析软件系统,包括任务管理、数据输入、屈曲分析、结果查看、能力曲线和文件分析等六个模块。为验证EPM方法的精度进行了系列纵向加筋和正交加筋板格试验模型的比较计算,并计算了四种典型加筋板格的双向应力能力曲线,与板格极限状态分析（PULS）软件和协调共同结构规范（HCSR）方法进行了比较分析。结果表明EPM方法可以分析联合载荷等因素对加筋板格极限强度的影响,文中开发的软件系统可用于加筋板格高级屈曲分析。     

Buckling and ultimate capability of plates and stiffened panels in axial compression

This paper presents extensive non-linear finite element (FE) analysis and formulation development work carried out on the ultimate compressive strength of plates and stiffened panels of ship structures. A review of contemporary designs for large ships was carried out. The existing formulae for plate ultimate compressive strength were reviewed and compared with non-linear FE analysis results. A semi-analytical formula for ultimate compressive strength assessments of stiffened panels was proposed and is described. The developed formula was verified against results using ABAQUS non-linear FE software for a series of 61 stiffened panels and a good agreement between the proposed formula and FE results were achieved. The method was verified against a large number of published FE results and was also compared with 58 experimental results. The developed method was also applied to the deck and bottom structures for a range of various sizes oil tankers and bulk carriers.     

加筋板屈曲和极限强度有限元计算方法研究

针对国际船级社协会双壳油船共同结构规范中加筋板屈吐和极限强度的计算要求,介绍了其技术背景和国内外相关研究现状,并通过分析各种因素对加筋板屈曲和极限强度的影响,研究国外相关技术文献,提出了一套完整的加强筋屈曲和极限强度有限元计算方法。与共同结构规范中要求的对标数据进行对比,验证了该方法的正确性。     

Evaluation of ultimate strength of stiffened panels under longitudinal thrust

A series of collapse analyses is performed applying nonlinear FEM on stiffened panels subjected to longitudinal thrust. MSC.Marc is used. Numbers, types and sizes of stiffeners are varied and so slenderness ratio as well as aspect ratio of local panels partitioned by stiffeners keeping the spacing between adjacent longitudinal stiffeners the same. Initial deflection of a thin-horse mode is imposed on local panels and that of flexural buckling and tripping modes on stiffeners to represent actual initial deflection in stiffened panels in ship structures. On the basis of the calculated results, buckling/plastic collapse behaviour of stiffened panels under longitudinal thrust is investigated. The calculated ultimate strength are compared with those obtained by applying several existing methods such as CSR for bulk carriers and PULS. Simple formulas for stiffened panels, of which collapse is dominated fundamentally by the collapse of local panels between longitudinal stiffeners, are also examined if they accurately estimate the ultimate strength. Through comparison of the estimated results with the FEM results, it has been concluded that PULS and modified FYH formulas fundamentally give good estimation of the ultimate strength of stiffened panels under longitudinal thrust.     

Ultimate strength assessment of a tanker hull based on experimentally developed master curves

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

基于试验获取主应力应变曲线的油船极限强度评估研究(英文)

A geometrically similar scaling was made from small-scale specimen to full-scale stiffened panels and then their collapse behaviour is investigated. It is considered that the stiffened panel compressive ultimate strength test was designed according to geometrical scaling laws so that the output of the test could be used as representative of the stiffened panels of the compressive zone of a tanker hull subjected to vertical bending moment. The ultimate strength of a tanker hull is analysed by a FE analysis using the experimentally developed master stress-strain curves which are obtained by the beam tension test and the compressive test of the stiffened panel, and are then compared with the result achieved by the progressive collapse method.     

A computational investigation of the effects of both-sides general corrosion on the buckling/plastic collapse behaviour and strength of stiffened plates

This paper presents the results of an investigation into the post-buckling behaviour and ultimate strength of imperfect corroded stiffened steel plates used in ships and other marine-related structures. A series of elastic–plastic large deflection finite element analyses is performed on stiffened steel plates suffering general corrosion wastage with random distribution. General corrosion is introduced into the finite element models using a random thickness surface model. The effects of corroded stiffened plate parameters on the post-buckling and ultimate strengths are evaluated in detail. The stiffeners of different symmetrical or unsymmetrical cross-sections are introduced into the models for analysis. Some distinctions are explored and highlighted between the behaviours of steel plates suffering general corrosion in unstiffened and stiffened cases. Finally, a proposal is given in order to simulate the average stress–average strain relationship of stiffened steel plates having both-surface general corrosion wastage.     

Compressive tests on short continuous panels

Results of eight tests on stiffened panels under axial compression until collapse and beyond are presented. The tests consider panels with different combinations of mechanical material properties and geometric configurations for the stiffeners including the use of ‘U’-shaped stiffeners. The specimens are three bay panels with associated plate made of high tensile steel S690. Four different configurations are considered for the stiffeners that are made of mild or high tensile steel for bar stiffeners and mild steel for ‘L’ and ‘U’ stiffeners. The influence of the stiffener's geometry on the ultimate strength of the stiffened panels under compression is analyzed.