结构刚度变化对箱式超大型浮体结构水弹性响应的影响

结构刚度改变会导致结构固有频率变化和结构广义刚度的变化。必然会对结构在波浪中的水弹性响应产生影响，本文在某箱式超大型浮体结构单位幅值正弦规则波和不规则波水弹性响应计算的基础上，假定结构质量分布不变，研究了结构刚度变化对箱式超大型浮体结构水弹性响应的影响。得到了一些有价值的结论。     

三维复杂弹性耦合冲击隔离系统建模研究

针对带弹性筏体和弹性基础的三维复杂弹性耦合冲击隔离系统,综合运用多体动力学理论、结构动力学理论、子结构方法、有限元方法,考虑系统刚体运动与弹性振动的耦合,建立了三维复杂弹性耦合冲击隔离系统的动力学模型;编写计算程序计算系统的固有频率,并与用ANSYS软件建模计算的固有频率和实验值进行比较,结果吻合得较好,通过试验工况下计算的机组加速度响应与实测结果的比较,验证了模型的正确性;最后计算分析系统在三向冲击激励下的动力学响应,为分析浮筏系统的冲击响应控制和参数优化奠定理论基础。     

三维复杂弹性耦合冲击隔离系统建模研究

针对带弹性筏体和弹性基础的三维复杂弹性耦合冲击隔离系统，综合运用多体动力学理论、结构动力学理论、子结构方法、有限元方法，考虑系统刚体运动与弹性振动的耦合，建立了三维复杂弹性耦合冲击隔离系统的动力学模型；编写计算程序计算系统的固有频率，并与用ANSYS软件建模计算的固有频率和实验值进行比较，结果吻合得较好，通过试验工况下计算的机组加速度响应与实测结果的比较，验证了模型的正确性；最后计算分析系统在三向冲击激励下的动力学响应，为分析浮筏系统的冲击响应控制和参数优化奠定理论基础。     

水中三维结构的湿模态分析方法

水中任意几何形状结构的流固耦合振动特性的研究对船舶及海洋工程应用具有很大的价值。本文利用三维水弹性分析方法计算流体附加质量和恢复力系数，然后求解由结构的干模态广义质量、广义刚度及流体附加质量、流体恢复力系数所构成的耦合特征方程，从而获得结构的湿模态及特征频率。计算结果与整体弹性船模式试验结果吻合。     

多不连通流域耦合的声介质中三维结构水弹性力学研究

在外流场与结构耦合的声介质中三维结构水弹性力学的基础上,提出多不连通流域耦合的声介质中三维结构水弹性力学计算方法。在计算中增加虚拟阻抗封闭曲面,用来消除不规则频率。在用于处理声弹耦合问题的大型三维水弹性计算程序THAFTS中,增加了多不连通流域耦合的计算功能。以舷间充水双层弹性球壳的结构声辐射问题为考核算例,通过与解析结果的比较,验证了计算方法和计算程序的正确性。     

考虑航速及自由液面影响的声介质中三维结构水弹性力学研究

基于Wu建立的带航速三维水弹性理论,采用考虑自由液面效应的理想可压流体Green函数,提出了带航速和考虑自由液面的声介质中三维水弹性结构声辐射计算方法.对THAFTS三维水弹性计算程序进行修改,得到声介质中三维水弹性计算程序.针对无限大流体中的静态弹性球壳结构声辐射模型进行一系列数值计算,通过与解析结果的比较,验证了该计算方法和计算程序的正确性.进一步计算不同潜深、不同航速下弹性球壳的结构声辐射,以此为基础对该计算方法和计算程序进行进一步考核,同时分析了航速和自由液面对水下结构声辐射的影响.     

超大型FPSO原油质量分布模拟与水弹性响应研究

FPSO在近海油气田开发中得到了越来越广泛的应用.大多数在渤海海域服役的FPSO工作在浅水海域.主尺度大与水深吃水小,直接导致FPSO水动力特性与深水条件下船舶的水动力特性有较大区别,因此采用水弹性理论研究超大型FPSO在浅水中的运动与波浪诱导载荷响应具有重要意义.浅水超大型FPSO满载时原油重量将近占载重量的80%,因此如何正确模拟原油重量分布对干结构的固有频率、广义质量和振型的计算非常重要.本文建立了基于三维水弹性理论的数值模型,开发了有限水深复合格林函数的数值计算程序模块,对一艘300K DWT FPSO在特定水深海况下的运动与波浪载荷响应进行了研究;同时采用三种方法模拟了原油质量分布.计算结果表明,不同的原油质量分布模拟方法对水弹性计算分析影响很大.     

四边固定支承矩形薄板振动分析的有限积分变换法

利用双重有限余弦积分变换的方法推导出了四边固定支承条件下,矩形薄板的固有频率和振型的解析解表达式.由于在求解过程中不需要事先人为地选取挠度函数,而是从弹性薄板的基本振动方程出发,直接利用数学的方法求出可以完全满足四边固定支承的边界条件,弹性矩形薄板的固有频率和振型解析解,使得问题的求解更加合理化.最后,还给出了计算实例来验证文中所采用的方法以及所推导出的公式的正确性.     

动态刚度阵法在船体总振动计算中的应用

采用动态刚度阵法计算船体总振动的固有频率.该方法不但能简化计算模型,而且能获得较高精度的高阶固有频率.首先通过直接求解等直Timoshenko梁单元的运动微分方程,导出考虑剪切变形和转动惯量影响的平面梁单元动态刚度阵的解析表达形式;其次采用Wittrick-Williams算法结合二分法求解特征值;最后采用本方法计算299 500DWT超大型油船船体总振动的固有频率,并分别与一维梁有限元法和三维全船有限元法计算结果以及实测值进行比较,验证了方法的精确性和有效性.     

基于改进MPS方法的三维时域水弹性计算模型

本文在作者已有的二维改进MPS(Moving Particle Semi-implicit)方法基础上进行了三维拓展(主要包括三维自由面粒子判断),并通过将计算得到的三维溃坝问题结果与文献中实验结果相对比,验证了所发展模型的准确性。在结构响应计算方面,将刚性和柔性模态耦合并计及相互影响。在此基础上,将流体和结构部分通过迭代方式耦合,从而实现强流固耦合计算。最后,应用上述模型对涉及大刚体位移叠加弹性变形的三维方梁的强非线性时域水弹性问题进行了计算,验证了模型对此类问题的有效性。     

基于直接计算方法的海上超大型浮式结构物单模块强度分析

海上超大型浮式结构是由若干个与半潜平台相似的浮体通过连接器相连而成的一种新型海上结构,目前对其结构强度分析较少。文章基于直接计算方法,采用SESAM/Hydro D进行超大浮体单模块水动力分析并预报其波浪载荷,进而调用SESAM/Sestra模块进行超大浮体总体强度有限元分析。分析表明,超大浮体的三个连接部位出现了较大应力集中。选取这三处连接部位作为关键节点,采用ANSYS计算该三处关键节点的局部强度。研究结果表明,在横撑与下浮体连接处总体和局部应力均最大,该部位是易产生疲劳破坏的部位,需要重点研究。     

超大型浮体模块水弹性响应和结构强度分析

水弹性方法针对超大型浮体的刚度特点,充分考虑了结构变形与流体运动的相互作用,是进行结构安全性分析的有效手段。文章采用水弹性分析方法研究了超大型浮体单模块总体波浪载荷以及结构应力响应。首先基于三维有限元方法分析了模块在真空中的总振动模态,然后结合模态叠加法和边界元法计算了模块在流场里面的谐振和模态响应。在此基础上,研究了各模态下结构的应力响应以及总应力响应,并分析了危险载荷工况,评估了超大型浮体单模块的结构强度,研究结果对超大型浮体单模块结构优化设计和安全性评估具有一定的指导意义。     

基于离散模块梁单元水弹性理论的复杂连接处建模方法

[目的]在离散模块?梁单元(DMB)水弹性理论框架下,提出针对连接形式复杂的超大型浮体结构(VLFS)的新的建模方法,并与已有方法进行对比分析.[方法]首先,概述基于DMB的水弹性分析方法,给出求解连续VLFS结构在波浪作用下的动力响应步骤;然后,针对VLFS复杂连接处进行建模,通过定义连接处的刚度矩阵,对与连接处相邻...     

Simplified estimation for the dynamic behavior and reliability analysis of very large floating structures under wave-induced loads

This paper deals with the dynamic response and strength of very large floating structures (VLFS) in regular and irregular waves, considering the propagation of the hydroelastic deflection wave of the structure. First, a simplified estimation method is presented for the dynamic response and strength of the structure in regular waves. Then, the validity of the method is demonstrated by comparing its results with analytical results and experimental results for a mat-type floating structure model. Next, a simplified estimation method for dynamic responses under long crested irregular wave conditions is presented by using the above results and by combining them with irregular sea wave spectra. Finally, the applicability of the method is investigated through numerical examples carried out for a 4,800-m class VLFS under trial design. Characteristics of the hydroelastic waves, short-term responses, and reliability levels are numerically identified. Received for publication on April 14, 1999; accepted on Sept. 10, 1999     

Analysis of the slowly varying drift force on a very large floating structure in multidirectional random seas

In designing the mooring system of a very large floating structure (VLFS), it is essential to estimate the slowly varying drift force in random seas. For a small vessel, Hsu's method or Newman's approximation may be used to simulate this slowly varying drift force. However, based on experiments and/or field observations, it was found that the slowly varying drift force acting on a VLFS could be reduced to a great extent from the simulated values based on those methods. Thus, the conventional methods are not applicable for a VLFS. This discovery led to the development of several methods for estimating the slowly varying drift force on a VLFS, e.g., Namba et al. (J Soc Nav Archit Jpn 186:235–242, 1999), and Shimada and Maruyama (J Soc Nav Archit Jpn 190:347–351, 2001). However, Namba's method is only applicable to a pontoon-type VLFS with a shallow draft, and Shimada's method is too simplified to account for the general shape of a VLFS and elastic deformation. These methods have been expanded in this article, and by our proposed method, any shape of VLFS and the effect of elastic deformation of the VLFS can be included. Formulations and several numerical examples are given.     

Elastic response characteristics of a very large floating structure in waves moored inside a reef

 This article describes the results of hydraulic model tests of the elastic response of a very large floating structure (VLFS) moored inside a reef in an isolated island. The distributions of strains and vertical displacements due to the elastic response of the VLFS were measured. The response characteristics were strongly affected by deformed nonlinear waves inside the reef. A two-step analytical method to compute the elastic response of a VLFS is proposed, and its validity is verified using the results of the hydraulic model tests. Received: May 2, 2002 / Accepted: March 17, 2003 RID="*" ID="*" Address correspondence to: S. Shiraishi (shiraishi@pari.go.jp) Acknowledgment. This study was supported by the Program for Promotions of Fundamental Transport Technology Research from the Corporation for Advanced Transport and Technology (CATT).     

Numerical calculation method for the hydroelastic response of a pontoon-type very large floating structure close to a breakwater

This paper presents an effective scheme for calculating the wave-induced hydroelastic response of a pontoon-type very large floating structure (VLFS) when it is near a breakwater. The basic numerical calculation method is the one previously developed by the same author for a VLFS in the open sea (no breakwater), which is expanded to include the effect of the hydrodynamic mutual interaction between the breakwater and the floating structure. The efficiency and accuracy of the proposed method are validated through comparisons with other numerical results and with existing experimental results. After that confirmation, various numerical calculations were conducted, paying special attention to the resonance phenomena which will occur depending on the relation between the wavelength and the clearance between the breakwater and the floating structure. The irregular frequency phenomenon which appears in the calculation of the fluid dynamic problem is discussed in the appendices, including a method for its elimination. Received: October 31, 2000 / Accepted: December 19, 2000     

一种提高分裂阵频域波束形成测向分辨力的方法

为了提高声呐系统对目标方位的分辨能力,本文提出一种分裂阵频域波束形成方法,即超波束互谱测向法。通过将超波束方法得到的方位谱加权到互谱方法得到的波束形成结果上,从而得到最终的波束输出结果。超波束互谱测向方法的优点是既能够降低主瓣宽度,抑制旁瓣,提高测向分辨力;又能够保留相位信息,为后续谱分析应用提供参考。实验室水池测试结果表明,利用阵元间距为0.016 m的16元均匀直线阵,对于37.5 kHz的声信号,采用超波束互谱方法进行波束形成与单纯采用互谱方法进行波束形成相比较,在0°和60°方位上的波束主瓣宽度分别减小了3.8°和6.9°,旁瓣幅度降低超过30 dB,测向分辨力得到明显提高,从而验证采用超波束互谱测向方法提高测向分辨力的可行性和有效性。     

Analytical and experimental study of free vibration of beams carrying multiple masses and springs

The structures in engineering can be simplified intoelastic beams with concentrated masses and elastic spring supports.Studying the law of vibration of the beams can be a help in guidingits design and avoiding resonance. Based on the Laplace transformmethod, the mode shape functions and the frequency equations ofthe beams in the typical boundary conditions are derived. Acantilever beam with a lumped mass and a spring is selected toobtain its natural frequencies and mode shape functions. Anexperiment was conducted in order to get the modal parameters ofthe beam based on the NExT-ERA method. By comparing theanalytical and experimental results, the effects of the locations ofthe mass and spring on the modal parameter are discussed. Thevariation of the natural frequencies was obtained with the changingstiffness coefficient and mass coefficient, respectively. The findingsprovide a reference for the vibration analysis methods and thelumped parameters layout design of elastic beams used inengineering.