Validation of an Articulated Vehicle Simulation

Tests were performed on a typical UK articulated vehicle to measure dynamic tyre forces and sprung mass accelerations. The measured road profile data and vehicle response data are used to determine some of the important characteristics of articulated vehicle vibration behaviour. In particular, roll motions and their effect on dynamic tyre forces are examined. The measured data are used to validate two and three-dimensional computer models of the vehicle. Attention is given to modelling the tandem leaf-spring trailer suspension. The conditions under which a two-dimensional model can accurately simulate vehicle behaviour are examined.     

Validation of an Articulated Vehicle Simulation

SUMMARY

Tests were performed on a typical UK articulated vehicle to measure dynamic tyre forces and sprung mass accelerations. The measured road profile data and vehicle response data are used to determine some of the important characteristics of articulated vehicle vibration behaviour. In particular, roll motions and their effect on dynamic tyre forces are examined. The measured data are used to validate two and three-dimensional computer models of the vehicle. Attention is given to modelling the tandem leaf-spring trailer suspension. The conditions under which a two-dimensional model can accurately simulate vehicle behaviour are examined.     

Tyre–road grip coefficient assessment. Part 1: off-line methodology using multibody dynamic simulation and genetic algorithms

A key factor to understand the vehicle dynamic behaviour is to know as accurately as possible the interaction that occurs between the tyre and the road, since it depends on many factors that influence the dynamic response of the vehicle. This paper aims to develop a methodology in order to characterise the tyre–road behaviour, applying it to obtain the tyre–road grip coefficient. This methodology is based on the use of dynamic simulation of a virtual model, integrated into a genetic algorithm that identifies the tyre–road friction coefficient in order to adjust the response obtained by simulation to real data. The numerical model was developed in collaboration with SEAT Technical Centre and it was implemented in multibody dynamic simulation software Adams®, from MSC®.     

Identifying tyre models directly from vehicle test data using an extended Kalman filter

Individual tyre models are traditionally derived from component tests, with their parameters matched to force and slip measurements. They are imported into vehicle models which should, but do not always properly provide suspension geometry interaction. Recent advances in Global Positioning System (GPS)/inertia vehicle instrumentation now make full state measurement viable in test vehicles, so tyre slip behaviour is directly measurable. This paper uses an extended Kalman filter for system identification, to derive individual load-dependent tyre models directly from these test vehicle state measurements. The resulting model therefore implicitly compensates for suspension geometry and compliance. The paper looks at two variants of the tyre model, and also considers real-time adaptation of the model to road surface friction variations. Test vehicle results are used exclusively, and the results show successful tyre model identification, improved vehicle model state prediction – particularly in lateral velocity reproduction – and an effective real-time solution for road friction estimation.     

Tyre friction behaviour under abrupt wheel torque transients on slippery road surfaces: experimental analysis and modelling

The paper shows that, during abrupt wheel torque transients for ice surface and low vehicle speeds, the tyre can develop significantly larger longitudinal force than the peak value of the tyre static curve. This so-called dynamic tyre friction potential (DTFP) effect has many influencing factors such as the rate of change of the wheel torque, the vehicle speed, and the tyre dwell time. The paper presents a detailed analysis of the DTFP behaviour based on the experimental data collected by using an in-wheel motor-based tyre test vehicle. The analysis results and an insight into the brush structure of a tyre model lead to the hypothesis that the different influencing factors may be predominantly explained by the bristle dwell time (BDT) effect. Following this hypothesis, the LuGre model of the tyre friction dynamics is extended with a physical BDT sub-model. The experimental validation results show that the proposed model can accurately capture the low-speed tyre–ice friction behaviour during abrupt wheel torque transients.     

Estimation of the tyre–road maximum friction coefficient and slip slope based on a novel tyre model

In this article, a new approach to estimate the vehicle tyre forces, tyre–road maximum friction coefficient, and slip slope is presented. Contrary to the majority of the previous work on this subject, a new tyre model for the estimation of the tyre–road interface characterisation is proposed. First, the tyre model is built and compared with those of Pacejka, Dugoff, and one other tyre model. Then, based on a vehicle model that uses four degrees of freedom, an extended Kalman filter (EKF) method is designed to estimate the vehicle motion and tyre forces. The shortcomings of force estimation are discussed in this article. Based on the proposed tyre model and the improved force measurements, another EKF is implemented to estimate the tyre model parameters, including the maximum friction coefficient, slip slope, etc. The tyre forces are accurately obtained simultaneously. Finally, very promising results have been achieved for pure acceleration/braking for varying road conditions, both in pure steering and combined manoeuvre simulations.     

A real-time approach to robust identification of tyre–road friction characteristics on mixed-μ roads

ABSTRACT

The interaction between the tyre and the road is crucial for understanding the dynamic behaviour of a vehicle. The road–tyre friction characteristics play a key role in the design of braking, traction and stability control systems. Thus, in order to have a good performance of vehicle dynamic stability control, real-time estimation of the tyre–road friction coefficient is required. This paper presents a new development of an on-line tyre–road friction parameters estimation methodology and its implementation using both LuGre and Burckhardt tyre–road friction models. The proposed method provides the capability to observe the tyre–road friction coefficient directly using measurable signals in real-time. In the first step of our approach, the recursive least squares is employed to identify the linear parameterisation form of the Burckhardt model. The identified parameters provide, through a T–S fuzzy system, the initial values for the LuGre model. Then, a new LuGre model-based nonlinear least squares parameter estimation algorithm using the proposed static form of the LuGre to obtain the parameters of LuGre model based on recursive nonlinear optimisation of the curve fitting errors is presented. The effectiveness and performance of the algorithm are demonstrated through the real-time model simulations with different longitudinal speeds and different kinds of tyres on various road surface conditions in both Matlab/Carsim environments as well as collected data from real experiments on a commercial trailer.     

Vehicle-Generated Road Damage: A Review

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

Noise,vibration, harshness model of a rotating tyre

ABSTRACT

The tyre plays a fundamental role in the generation of acoustically perceptible driving noise and vibrations inside the vehicle. An essential part of these vibrations is induced by the road excitation and transferred via the tyre into the vehicle. There are two basic ways to study noise, vibration, harshness (NVH) behaviour: Simulations in time and frequency domains. Modelling the tyre transfer behaviour in frequency domain requires special attention to the rotation of the tyre. This paper shows the approach taken by the authors to include the transfer behaviour in the frequency range up to 250?Hz from geometric road excitations to resulting spindle forces in frequency domain. This paper validates the derived NVH tyre model by comparison with appropriate transient simulations of the base transient model.     

Total dynamic response of a PSS vehicle negotiating asymmetric road excitations

A planar suspension system (PSS) is a novel automobile suspension system in which an individual spring–damper strut is implemented in both the vertical and longitudinal directions, respectively. The wheels in a vehicle with such a suspension system can move back and forth relative to the chassis. When a PSS vehicle experiences asymmetric road excitations, the relative longitudinal motion of wheels with respect to the chassis in two sides of the same axle are not identical, and thus the two wheels at one axle will not be aligned in the same axis. The total dynamic responses, including those of the bounce, pitch and the roll of the PSS vehicle, to the asymmetric road excitation may exhibit different characteristics from those of a conventional vehicle. This paper presents an investigation into the comprehensive dynamic behaviour of a vehicle with the PSS, in such a road condition, on both the straight and curved roads. The study was carried out using an 18 DOF full-car model incorporating a radial-spring tyre–ground contact model and a 2D tyre–ground dynamic friction model. Results demonstrate that the total dynamic behaviour of a PSS vehicle is generally comparable with that of the conventional vehicle, while PSS exhibits significant improvement in absorbing the impact forces along the longitudinal direction when compared to the conventional suspension system. The PSS vehicle is found to be more stable than the conventional vehicle in terms of the directional performance against the disturbance of the road potholes on a straight line manoeuvre, while exhibiting a very similar handling performance on a curved line.     

User-Appropriate Tyre-Modelling for Vehicle Dynamics in Standard and Limit Situations

Summary When modelling vehicles for the vehicle dynamic simulation, special attention must be paid to the modelling of tyre-forces and -torques, according to their dominant influence on the results. This task is not only about sufficiently exact representation of the effective forces but also about user-friendly and practical relevant applicability, especially when the experimental tyre-input-data is incomplete or missing. This text firstly describes the basics of the vehicle dynamic tyre model, conceived to be a physically based, semi-empirical model for application in connection with multi-body-systems (MBS). On the basis of tyres for a passenger car and a heavy truck the simulated steady state tyre characteristics are shown together and compared with the underlying experimental values. In the following text the possibility to link the tyre model TMeasy to any MBS-program is described, as far as it supports the 'Standard Tyre Interface' (STI). As an example, the simulated and experimental data of a heavy truck doing a standardized driving manoeuvre are compared.     

Analysis of wheel speed vibrations for road friction classification

ABSTRACT

With higher level of vehicle automation, it becomes increasingly important to know the maximum possible tyre forces during normal driving. An interesting method in this respect is estimating the tyre–road friction from the resonance peak in the wheel speed signal, excited by road roughness. A simulation environment using the MF-Swift tyre model is proposed, which gives insight in the correctness and functioning of this method. From implementing the estimation algorithm and considering the tyre torsional vibration system, it is concluded that frequencies and damping ratios can be estimated with reasonable accuracy and that the trends observed with changing road friction are consistent. Furthermore, the proposed simulation environment gives opportunity to investigate other issues like robustness of the estimation method to road roughness. Additionally, the tyre modelling aspect of the estimation method is analysed and improvements are proposed.     

New tyre-road contact model for applications at low speed

Most of the tyre models have been developed for high speed, combined forces, etc., however, in certain tests it is necessary to know tyre behaviour at very low speed in order to evaluate different systems. So, during vehicle inspection and maintenance of the steering and brake system, by means of sideslip tester and roller brake tester respectively, the forces transmitted by the tyres are measured; all of these inspections are carried out at low speeds. Furthermore, usually, automobile vehicles run at low speeds during an important part of their operating life (less than 60 km/h), mainly during urban traffic, and in steady state conditions. Therefore, it is particularly interesting to develop an accurate model of the contact patch tyrepavement for low speeds without the complexity of models that cover a wide speed range but provide less precision at very low speeds. The dynamometer plate has proved to be an appropriate test equipment to characterise the tyre-pavement contact at low speed and the steering geometry and wheel alignment. It has the feature of being able to carry out tests with the tyre installed in the vehicle as in completely real conditions. The main aim of this research is to set up a contact model between tyre and pavement at very low speed based on the measurement of longitudinal and lateral forces. A test methodology that allows carrying out the experimental tests in a systematic and controlled way with the dynamometer plate has also been developed. From this model it will be possible to estimate the forces that tyres are capable of transmitting in different situations to act in the parameters which affect these forces and maximize them.     

Rail Vehicles' Riding Quality and Comfort Related to Theoretical and Experimental Optimization Application to High Speed Trains

SUMMARY

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

Using the lead vehicle as preview sensor in convoy vehicle active suspension control

Both ride quality and roadholding of actively suspended vehicles can be improved by sensing the road ahead of the vehicle and using this information in a preview controller. Previous applications have used look-ahead sensors mounted on the front bumper to measure terrain beneath. Such sensors are vulnerable, potentially confused by water, snow, or other soft obstacles and offer a fixed preview time. For convoy vehicle applications, this paper proposes using the overall response of the preceding vehicle(s) to generate preview controller information for follower vehicles. A robust observer is used to estimate the states of a quarter-car vehicle model, from which road profile is estimated and passed on to the follower vehicle(s) to generate a preview function. The preview-active suspension, implemented in discrete time using a shift register approach to improve simulation time, reduces sprung mass acceleration and dynamic tyre deflection peaks by more than 50% and 40%, respectively. Terrain can change from one vehicle to the next if a loose obstacle is dislodged, or if the vehicle paths are sufficiently different so that one vehicle misses a discrete road event. The resulting spurious preview information can give suspension performance worse than that of a passive or conventional active system. In this paper, each vehicle can effectively estimate the road profile based on its own state trajectory. By comparing its own road estimate with the preview information, preview errors can be detected and suspension control quickly switched from preview to conventional active control to preserve performance improvements compared to passive suspensions.     

Tyre–road grip coefficient assessment – Part II: online estimation using instrumented vehicle,extended Kalman filter,and neural network

The main objective of this work is to determine the limit of safe driving conditions by identifying the maximal friction coefficient in a real vehicle. The study will focus on finding a method to determine this limit before reaching the skid, which is valuable information in the context of traffic safety. Since it is not possible to measure the friction coefficient directly, it will be estimated using the appropriate tools in order to get the most accurate information. A real vehicle is instrumented to collect information of general kinematics and steering tie-rod forces. A real-time algorithm is developed to estimate forces and aligning torque in the tyres using an extended Kalman filter and neural networks techniques. The methodology is based on determining the aligning torque; this variable allows evaluation of the behaviour of the tyre. It transmits interesting information from the tyre–road contact and can be used to predict the maximal tyre grip and safety margin. The maximal grip coefficient is estimated according to a knowledge base, extracted from computer simulation of a high detailed three-dimensional model, using Adams^® software. The proposed methodology is validated and applied to real driving conditions, in which maximal grip and safety margin are properly estimated.