Experimental and numerical analysis of the influence of tyres’ properties on the straight running stability of a sport-touring motorcycle

The behaviour of a motorcycle on the road is largely governed by tyre properties. This paper presents experimental and numerical analyses dealing with the influence of tyre properties on the stability of weave and wobble in straight running. The final goal is to find optimal sets of tyre properties that improve the stability of a motorcycle. The investigation is based on road tests carried out on a sport-touring motorcycle equipped with sensors. Three sets of tyres are tested at different speeds in the presence of weave and wobble. The analysis of telemetry data highlights significant differences in the trends of frequency and damping of weave and wobble against speed. The experimental analysis is integrated by a parametric numerical analysis. Tyre properties are varied according to the design of experiments method, in order to highlight the single effects on stability of lateral and cornering coefficient of front and rear tyres.     

Further study on the wheel–rail impact response induced by a single wheel flat: the coupling effect of strain rate and thermal stress

A comprehensive dynamic finite-element simulation method was proposed to study the wheel–rail impact response induced by a single wheel flat based on a 3-D rolling contact model, where the influences of the structural inertia, strain rate effect of wheel–rail materials and thermal stress due to the wheel–rail sliding friction were considered. Four different initial conditions (i.e. pure mechanical loading plus rate-independent, pure mechanical loading plus rate-dependent, thermo-mechanical loading plus rate-independent, and thermo-mechanical loading plus rate-dependent) were involved into explore the corresponding impact responses in term of the vertical impact force, von-Mises equivalent stress, equivalent plastic strain and shear stress. Influences of train speed, flat length and axle load on the flat-induced wheel–rail impact response were discussed, respectively. The results indicate that the maximum thermal stresses are occurred on the tread of the wheel and on the top surface of the middle rail; the strain rate hardening effect contributes to elevate the von-Mises equivalent stress and restrain the plastic deformation; and the initial thermal stress due to the sliding friction will aggravate the plastic deformation of wheel and rail. Besides, the wheel–rail impact responses (i.e. impact force, von-Mises equivalent stress, equivalent plastic strain, and XY shear stress) induced by a flat are sensitive to the train speed, flat length and axle load.     

A method to determine the two-point contact zone and transfer of wheel–rail forces in a turnout

A practical method to determine the zone of two contact points and the transfer of wheel–rail forces between two rails in a turnout is presented in this paper. The method is based on a wheel–rail elastic penetration assumption and used to study a turnout system for a 200 km/h high-speed railway in China. Rail profiles in a number of key sections in the turnout are identified first, and profiles in other sections are then obtained by interpolation between key sections. The track is modelled as flexible with rails and sleepers represented by beams and the interaction between the vehicle and turnout is simulated for cases of the vehicle passing the turnout. Results are mainly presented for two-point contact positions and the characteristics of the wheel–rail forces transference. It is found that the heights of the switch and crossing rail top have significant effects on the wheel–rail contact forces. Finally, the optimised top height for the crossing rails is proposed to reduce the system dynamic force in the turnout system.     

A survey of wheel–rail contact models for rail vehicles

Accurate and efficient contact models for wheel–rail interaction are essential for the study of the dynamic behaviour of a railway vehicle. Assessment of the contact forces and moments, as well as contact geometry provide a fundamental foundation for such tasks as design of braking and traction control systems, prediction of wheel and rail wear, and evaluation of ride safety and comfort. This paper discusses the evolution and the current state of the theories for solving the wheel–rail contact problem for rolling stock. The well-known theories for modelling both normal contact (Hertzian and non-Hertzian) and tangential contact (Kalker's linear theory, FASTSIM, CONTACT, Polach's theory, etc.) are reviewed. The paper discusses the simplifying assumptions for developing these models and compares their functionality. The experimental studies for evaluation of contact models are also reviewed. This paper concludes with discussing open areas in contact mechanics that require further research for developing better models to represent the wheel–rail interaction.     

Assessment of a semi-Hertzian method for determination of wheel–rail contact patch

Wheel–rail contact calculations are essential for simulating railway vehicle dynamic behavior. Currently, these simulations usually use the Hertz contact theory to calculate normal forces and Kalker's ‘FASTSIM’ program to evaluate tangential stresses. Since 1996, new methods called semi-Hertzian have appeared: 5 Kik, W. and Piotrowski, J. A fast approximate method to calculate normal load at contact between wheel and rail and creep forces during rolling. Paper presented at the 2nd Mini-conference on Contact Mechanics and Wear of Rail/Wheel Systems. July29–31, Budapest.  [Google Scholar] 7 Ayasse, J. B., Chollet, H. and Maupu, J. L. 2000. Paramètres caractéristiques du contact roue-rail. Rapport de Recherche INRETS n225, ISSN 0768–9756 (in French) [Google Scholar] (STRIPES). These methods attempt to estimate the non-elliptical contact patches with a discrete extension of the Hertz theory. As a continuation of 2 Ayasse, J. B and Chollet, H. 2005. Determination of the wheel–rail contact patch in semi-Hertzian conditions. Vehicle System Dynamics, 43(3) [Google Scholar], a validation of the STRIPES method for normal problem computing on three test cases is proposed in this article. The test cases do not fulfill the hypothesis required for the Hertz theory. Then, the Kalker's FASTSIM algorithm is adapted to STRIPES patch calculus to perform tangential forces computation. This adaptation is assessed using Kalker's CONTACT algorithm.     

Sensitivity of the wheel–rail contact interactions and Dang Van Fatigue Index in the rail with respect to irregularities of the track geometry

This paper investigates the effects of the track geometry irregularities on the wheel–rail dynamic interactions and the rail fatigue initiation through the application of the Dang Van criterion, that supposes an elastic shakedown of the structure. The irregularities are modelled, using experimental data, as a stochastic field which is representative of the considered railway network. The tracks thus generated are introduced as the input of a railway dynamics software to characterise the stochastic contact patch and the parameters on which it depends: contact forces and wheelset–rail relative position. A variance-based global sensitivity analysis is performed on quantities of interest representative of the dynamic behaviour of the system, with respect to the stochastic geometry irregularities and for different curve radius classes and operating conditions. The estimation of the internal stresses and the fatigue index being more time-consuming than the dynamical simulations, the sensitivity analysis is performed through a metamodel, whose input parameters are the wheel–rail relative position and velocity. The coefficient of variation of the number of fatigue cycles, when the simulations are performed with random geometry irregularities, varies between 0.13 and 0.28. In a large radius curve, the most influent irregularity is the horizontal curvature, while, in a tight curve, the gauge becomes more important.     

An analytical mathematical method for calculation of the dynamic wheel–rail impact force caused by wheel flat

The simplified method to determine a vertical impact force of wheel with flat and rail interaction is presented in this article. The presented simplified method can be used to identify maximum contact force and its distribution in the contact length between the damaged wheel and the rail. The vertical impact force depends on geometrical parameters of the rail and wheel with flat, speed of vehicle and the angle of deviation of rail. This article demonstrates the influence of wheel with flat geometrical parameters, speed of vehicle to maximum contact force and its distribution in the contact zone. The obtained values of the simplified method for determination of a vertical contact force are compared with the results obtained from field measurements.     

Modelling,validation and analysis of a three-dimensional railway vehicle–track system model with linear and nonlinear track properties in the presence of wheel flats

This paper presents dynamic contact loads at wheel–rail contact point in a three-dimensional railway vehicle–track model as well as dynamic response at vehicle–track component levels in the presence of wheel flats. The 17-degrees of freedom lumped mass vehicle is modelled as a full car body, two bogies and four wheelsets, whereas the railway track is modelled as two parallel Timoshenko beams periodically supported by lumped masses representing the sleepers. The rail beam is also supported by nonlinear spring and damper elements representing the railpad and ballast. In order to ensure the interactions between the railpads, a shear parameter beneath the rail beams has also been considered into the model. The wheel–rail contact is modelled using nonlinear Hertzian contact theory. In order to solve the coupled partial and ordinary differential equations of the vehicle–track system, modal analysis method is employed. Idealised Haversine wheel flats with the rounded corner are included in the wheel–rail contact model. The developed model is validated with the existing measured and analytical data available in the literature. The nonlinear model is then employed to investigate the wheel–rail impact forces that arise in the wheel–rail interface due to the presence of wheel flats. The validated model is further employed to investigate the dynamic responses of vehicle and track components in terms of displacement, velocity, and acceleration in the presence of single wheel flat.     

A study on the development strategy of China’s auto parts industry

1. Development trend As an important part of automobile, auto parts are the base of the auto industry. At the age of economic globalization and along with the change of the auto industry, the world auto parts industry is presenting new development trend. First, since the late 80’s and early 90’s, promoted by economic globalization, the world auto industry has fastened restructuring. The number of powerful auto makers is now 12 from 30 in 1980. The restructuring of auto makers has broken the…     

A non-Hertzian method for solving wheel–rail normal contact problem taking into account the effect of yaw

A novel approach is proposed in this paper to deal with non-Hertzian normal contact in wheel–rail interface, extending the widely used Kik–Piotrowski method. The new approach is able to consider the effect of the yaw angle of the wheelset against the rail on the shape of the contact patch and on pressure distribution. Furthermore, the method considers the variation of profile curvature across the contact patch, enhancing the correspondence to CONTACT for highly non-Hertzian contact conditions. The simulation results show that the proposed method can provide more accurate estimation than the original algorithm compared to Kalker’s CONTACT, and that the influence of yaw on the contact results is significant under certain circumstances.     

An alternative to FASTSIM for tangential solution of the wheel–rail contact

In most rail vehicle dynamics simulation packages, tangential solution of the wheel–rail contact is gained by means of Kalker's FASTSIM algorithm. While 5–25% error is expected for creep force estimation, the errors of shear stress distribution, needed for wheel–rail damage analysis, may rise above 30% due to the parabolic traction bound. Therefore, a novel algorithm named FaStrip is proposed as an alternative to FASTSIM. It is based on the strip theory which extends the two-dimensional rolling contact solution to three-dimensional contacts. To form FaStrip, the original strip theory is amended to obtain accurate estimations for any contact ellipse size and it is combined by a numerical algorithm to handle spin. The comparison between the two algorithms shows that using FaStrip improves the accuracy of the estimated shear stress distribution and the creep force estimation in all studied cases. In combined lateral creepage and spin cases, for instance, the error in force estimation reduces from 18% to less than 2%. The estimation of the slip velocities in the slip zone, needed for wear analysis, is also studied. Since FaStrip is as fast as FASTSIM, it can be an alternative for tangential solution of the wheel–rail contact in simulation packages.     

A motorcycle giant is to be formed by acquisition with Japanese Suzuki as the leading supporter

Recently, an announcement by listed company Qianjiang Motor ( 000913, SZ ) said that the managing personnel of Grand River Group and Qianjiang Group will purchase the total state-owned shares of Qianjiang Group, which may mean a change in the control of Qianjiang Motor. An insider says that, according to statistics of CAAM, in 2003, Grand River Group ranked first in the industry, with 1.0099 million motorcycles produced and sales of 1.0463 million, while Qianjiang Group was listed the …     

Comments on ‘the Kalker book of tables for non-Hertzian contact of wheel and rail’

The ‘simple double-elliptical contact’ (SDEC) approach by Piotrowski et al. [The Kalker book of tables for non-Hertzian contact of wheel and rail. Vehicle Syst Dyn. 2017;55:875–901] generates a-symmetrical contact patches in an elegant way. This allows to extend the table-based approach for the wheel–rail creep force calculation towards non-Hertzian contact geometry. This is an important line of research, because FASTSIM is intricate for non-Hertzian contacts, whereas CONTACT requires long calculation times.

Here, we comment on the further motivation that's provided for the approach. According to the authors, ‘the spin creepage generates longitudinal creep force in non-symmetric, non-elliptical contacts’, which is ‘completely lost’ when using elliptical regularisation. We demonstrate that this mainly depends on the choice of contact origin, and that the interaction is much reduced if different choices are made. This suggests that elliptical regularisation may be viable still, if the details are properly worked out. Furthermore, we introduce the spin center and the free-rolling position as means to extend the table-based approach towards more general non-Hertzian circumstances.     

A new mechanism hammered out for settling the intellectual property rights dispute on motorcycle between Japan and China

An agreement on the issue was signed recently by CAAM, JAMA and CCOICwhichmeans a new resolution for the issue. Disputes on motorcycles have cropped up frequently in recent years. For example,Shanghai Feiling Motorcycle and Zhejiang Huangyan Huari (Group) were accused ofviolating the patents of Honda’s KCW. Chongqing Lifan Motorcycle was also accused by Honda for using the trademarkHongda which is regarded toosimilar to Honda which was registered by Honda Motor Co.,Ltd in 1982.…     

On the sway stability improvement of car–caravan systems by articulated connections

The present analysis is addressed to some promising connection arrangements between the towing vehicles and the towed trailers, where the two units are linked by four-bar isosceles trapeziums in place of the conventional pintle hitch. Two types of instability, of the divergent type or the oscillating type, may be analysed by the Routh–Hurwitz criterion or by the direct analysis of the characteristic equation. The constant term of this equation vanishes at the divergent instability threshold (zero of a real root), whereas the equation splits into two lower degree algebraic ‘sub-equations’ when the oscillating instability arises (pair of pure imaginary roots). A large field of geometrical configurations of the four-bar linkage may be quickly tested by numerical search procedures, including those where the sidebars of the linkage converge towards the inside of the drawing car and shift the relative centre of rotation forward, and those converging backward towards the trailer. Maps of the critical velocity as a function of the geometrical or physical parameters may be easily traced. They clearly show the favourable influence of the forward four-bar connection in general and the benefits achievable comparing with the conventional coupling. Actually, it is conceivable to increase the critical speed by optimising the four-bar design depending on the weight distribution on the axles and on the other geometrical and physical properties. Moreover, this type of connection may produce significant corrections to the under-steering or over-steering conduct of the articulated vehicle. The off-tracking and the manoeuvrability along curved paths are also studied, showing the benefits or the drawbacks of the four-bar linkage for the various configurations.     

High-frequency random vibration analysis of a high-speed vehicle–track system with the frequency-dependent dynamic properties of rail pads using a hybrid SEM–SM method

A hybrid Spectral Element Method (SEM)–Symplectic Method(SM) method for high-efficiency computation of the high-frequency random vibrations of a high-speed vehicle–track system with the frequency-dependent dynamic properties of rail pads is presented. First, the Williams-Landel-Ferry (WLF) formula and Fractional Derivative Zener (FDZ) model were, respectively, applied for prediction and representation of the frequency-dependent dynamic properties of Vossloh 300 rail pads frequently used in China's high-speed railway. Then, the proposed hybrid SEM–SM method was used to investigate the influence of the frequency-dependent dynamic performance of Vossloh 300 rail pads on the high-frequency random vibrations of high-speed vehicle–track systems at various train speeds or different levels of rail surface roughness. The experimental results indicate that the storage stiffness and loss factors of Vossloh 300 rail pad increase with the decrease in dynamic loads or the increase in preloads within 0.1–10,000?Hz at 20°C, and basically linearly increase with frequency in a logarithmic coordinate system. The results computed by the hybrid SEM–SM method demonstrate that the frequency-dependent viscous damping of Vossloh 300 rail pads, compared with its constant viscous damping and frequency-dependent stiffness, has a much more conspicuous influence on the medium-frequency (i.e. 20–63?Hz) random vibrations of car bodies and rail fasteners, and on the mid- (i.e. 20–63?Hz) and high-frequency (i.e. 630–1250?Hz) random vibrations of bogies, wheels and rails, especially with the increase in train speeds or the deterioration of rail surface roughness. The two sensitive frequency bands can also be validated by frequency response function (FRF) analysis of the proposed infinite rail–fastener model. The mid and high frequencies influenced by the frequency-dependent viscous damping of rail pads are exactly the dominant frequencies of ground vibration acceleration and wheel rolling noise caused by high-speed railways, respectively. Even though the existing time-domain (or frequency-domain) finite track models associated with the time-domain (or frequency-domain) fractional derivative viscoelastic (FDV) models of rail pads can also be used to reach the same conclusions, the hybrid SEM–SM method in which only one element is required to compute the high-order vibration modes of infinite rail is more appropriate for high-efficiency analysis of the high-frequency random vibrations of high-speed vehicle–track systems.     

A Study on the Emission Characteristics of Volatile Organic Compounds from a State-Ⅲ Diesel Engine

采用热脱附-气相色谱-质谱联用技术(TD-CC-MS)对国3柴油机排气中的挥发性有机物进行了分析.在国3柴油机不同转速和负荷下的排气中定性检出烷烃、烯烃、芳香烃等90余种挥发性有机物,且在VOC8中以碳数C5-C20的化合物为主,其中C8化合物排放比例最高,为9.81％～15.41％.试验结果表明,芳香烃中的苯、甲苯、对二甲苯、间二甲苯、邻二甲苯、乙苯、苯乙烯、萘等排放量较高,其中排放水平最高的为甲苯;在相同转速下,苯乙烯的排放随着发动机负荷的增加而降低;而其他芳香烃则随着柴油机负荷的增加呈先降后增的变化趋势;在相同负荷下,多数芳香烃在中低负荷时随着发动机转速的增加而降低,但在高负荷时随发动机转速增加变化幅度很小.     

A Brief Analysis of the Impact of the Macro Economy on the Heavy Truck Market in 2005

Over the past two decades, China’s heavy truck market has grown to 1.5 million trucks. From 1998 through 2004, the market was in booming. But in the next few years, the development pace will be slowed down, mainly due to the macro regulation and control. It is well known that China’s auto market has been dominated by government policies and the heavy truck segment is in particular no exception. It is reported that after the “car rush”, this year’s focus is heavy trucks. On top of the ca…     

Stable with Slight Bounce, Waxing with Wane A Primer Analysis on Auto Market Operation in the First Half of 1997

The first half of 1997 sees Chinese auto market operating with the theme of seeking sta-ble increase and progressing with steady steps. But the situation varies greatly with different au-to product types and manufacturers, it may be said it is like the moon having wax and wane.