Preferences for alternative fuel vehicles by Dutch local governments

Using a choice model, we estimate the preferences for alternative fuel vehicles by Dutch local governments. The analysis shows that local governments are willing to pay between 25% and 50% extra for an alternative fuel vehicle without a serious loss of utility. Further, local emissions are an important criterion on which to base a decision, especially for municipalities and provinces. We also calculate the utility for a number of prominent alternative fuel vehicles. We find that show that local governments value the battery electric vehicle and biogas internal combustion engine equally. It is important, however, that the time to refuel for electric vehicles is reduced to about 30 min.     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

The impact of competition on container port (in)efficiency

There are many studies on container port efficiency and that seek to understand what factors, such as technical and scale efficiency, private versus public terminal management or macro-economic factors, play on the efficiency score of a given port. There are fewer studies that focus on the role played by the inter-port competitive environment. This role remains difficult to assess. In fact, on the one hand, a port subject to high inter-port competition may record higher efficiency scores due to the pressure from the competitive environment. On the other hand, a port subject to high competition may be forced to over-invest and could therefore records a lower efficiency score. This article investigates this issue and examines how the degree of competition measured at different levels (local, regional and global level) impacts the efficiency score of a given container port. To do so, we implement a truncated regression with a parametric bootstrapping model. The model applied to information gathered for 200 container ports in 2007 and 2010 leads to the following conclusions: port efficiency decreases with competition intensity when measured in a range of 400–800 km (regional level); and the effect from competition is not significant when competition is measured at a local (less than 300 km) or at a global (more than 800 km) level. Estimates also show a tendency for ports who invested from 2007 to 2010 to experience a general decrease in efficiency scores, an element which could be explained by the time lag between the investment and the subsequent potential increase in container throughput.     

Fast computing and approximate fuel consumption modeling for Internal Combustion Engine passenger cars

This article presents a fuel consumption model, SEFUM (Semi Empirical Fuel Use Modeling), and its comparison with three models from the literature on a 600 km experimental database. This model is easy to calibrate with only a few required parameters that are provided by car manufacturers. The test database has been built from 21 drivers who drove in two conditions (normal and ecodriving) on a 15 km trip. For the model evaluation, three indicators have been selected: instantaneous fuel use root mean square error, cumulated error and computation time in order to evaluate the accuracy both in cumulated and instantaneous fuel use and to estimate computation time of each model. Results tend to prove that the model is able to compute rapidly (maximum of 1500 simulated kilometers under Matlab) in comparison to all other models while ensuring a high accuracy and precision for cumulated and instantaneous fuel use.     

Estimating the CO2 intensity of intermodal freight transportation

This paper looks at the environmental effects of shifting from road to rail freight transportation. Little data is available to shippers to calculate the potential CO₂ savings of an intermodal shift. In this paper we analyze a data set of more than 400,000 intermodal shipments to calculate the CO₂ intensity of intermodal transportation as a distinct mode. Our results indicate an average intensity of 67 g of CO₂ per ton-mile, but can vary between 29 and 220 g of CO₂ per ton-mile depending on the specific origin–destination lane. We apply the market area concept to explain the variance between individual lane intensities and demonstrate the complexity in predicting the potential carbon savings in a switch from truckload to intermodal.     

Idling stop fines for exceeding legal idling times – From the driver’s perspective

In order to reduce CO₂ emissions from motorised transport, the Taiwanese government implemented an idling policy for vehicles in 2012. This paper applies a contingent valuation framework based on stated preference questions to calculate a reasonable fine for idling vehicles based on drivers’ preferences in Taiwan. Drivers were surveyed at urban roadsides to determine the amount of money they would prefer to pay for idling in excess of the 3 min currently allowed by law. The results obtained from our spike model analysis showed that drivers would prefer to pay a fine of 1720 NTD (approximately USD 57).     

Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Responses to differentiated road pricing schemes

Reducing traffic-related problems is an important issue that requires changes in travel behavior. It is argued that road pricing is an effective tool but that it would be more effective if charges are differentiated. A laboratory experiment employing a heterogeneous sample (n = 155) examined effects of differentiated road pricing schemes on understanding and behavioral change intentions. The results show that difficulties are experienced in calculating the charges for road pricing schemes differentiated with respect to both place and time. Suggesting learning effects, if presented with degree of differentiation gradually increasing compared to random orders, the highly differentiated schemes were evaluated faster, as more comprehensible, and perceived difficulty decreased. Elderly were less flexible than young people in indicating how they would respond, women were more flexible than men, and frequent drivers less flexible than non-frequent drivers. A distance-based road pricing scheme with a fixed charge per kilometer was on average ranked highest on preference compared to several other conceivable road pricing alternatives.     

China’s electric car frustrations

By 2020, the vehicle population in China will likely exceed 280 million—exacerbating national energy security, urban air pollution, and traffic congestion. In response, many local and regional governments in China are pursuing an expanding array of measures to restrain growth in personal vehicle ownership and, along with the central government, reducing emissions and energy use of vehicles. One prominent strategy is the promotion of new energy vehicles, especially plug-in electric vehicles (PEVs). Large subsidies were offered—up to $27,600 (171,000 RMB) per vehicle in some regions, including almost $9200 (57,000 RMB) from the central government—which suggests that China is making a major commitment to PEVs. But sales have been meager. In 2013, only 17,600 PEVs, mostly buses and utility trucks, were sold, less than 0.1% of total civilian vehicle sales. Several factors explain the failure of PEV sales to take off: (1) protectionism by local governments; (2) uncertainty over which electric-drive vehicle technologies to promote and what consumers are willing to pay, (3) lagging investments in charging infrastructure, and (4) conservative investment behavior by automakers and battery manufacturers. The central government issued directives to local governments in late 2013 to reduce barriers to out-of-town companies, resulting in modest sales increases in early 2014, but a more coherent, broader, and effective set of policies, incentives, and strategies are needed to overcome consumer and industry resistance and the lack of charging infrastructure.     

On the electrification of road transportation – A review of the environmental,economic, and social performance of electric two-wheelers

Electrification is widely considered as a viable strategy for reducing the oil dependency and environmental impacts of road transportation. In pursuit of this strategy, most attention has been paid to electric cars. However, substantial, yet untapped, potentials could be realized in urban areas through the large-scale introduction of electric two-wheelers. Here, we review the environmental, economic, and social performance of electric two-wheelers, demonstrating that these are generally more energy efficient and less polluting than conventionally-powered motor vehicles. Electric two-wheelers tend to decrease exposure to pollution as their environmental impacts largely result from vehicle production and electricity generation outside of urban areas. Our analysis suggests that the price of e-bikes has been decreasing at a learning rate of 8%. Despite price differentials of 5000 ± 1800 EUR₂₀₁₂ kW h⁻¹ in Europe, e-bikes are penetrating the market because they appear to offer an apparent additional use value relative to bicycles. Mid-size and large electric two-wheelers do not offer such an additional use value compared to their conventional counterparts and constitute niche products at price differentials of 700 ± 360 EUR₂₀₁₂ kW⁻¹ and 160 ± 90 EUR₂₀₁₂ kW⁻¹, respectively. The large-scale adoption of electric two-wheelers can reduce traffic noise and road congestion but may necessitate adaptations of urban infrastructure and safety regulations. A case-specific assessment as part of an integrated urban mobility planning that accounts, e.g., for the local electricity mix, infrastructure characteristics, and mode-shift behavior, should be conducted before drawing conclusions about the sustainability impacts of electric two-wheelers.     

Biofuels in aviation: Fuel demand and CO2 emissions evolution in Europe toward 2030

This article presents the results of a scenario-based study carried out at the European Commission’s Joint Research Centre aimed at analyzing the future growth of aviation, the resulting fuel demand and the deployment of biofuels in the aviation sector in Europe. Three scenarios have been produced based on different input assumptions and leading to different underlying patterns of growth and resulting volumes of traffic. Data for aviation growth and hence fuel demand have been projected on a year by year basis up to 2030, using 2010 as the baseline. Data sources are Eurostat statistics and actual flight information from EUROCONTROL. Relevant variables such as the number of flights, the type of aircrafts, passengers or cargo tonnes and production indicators (RPKs) are used together with fuel consumption and CO₂ emissions data. The target of the European Advanced Biofuels Flightpath to ensure the commercialization and consumption of 2 million tons of sustainably produced paraffinic biofuels in the aviation sector by 2020, has also been taken into account. Results regarding CO₂ emission projections to 2030, reveal a steady annual increase in the order of 3%, 1% and 4% on average, for the three different scenarios, providing also a good correlation compared to the annual traffic growth rates that are indicated in the three corresponding scenarios. In absolute values, these ratios correspond to the central, the pessimistic and the optimistic scenarios respectively, corresponding to 360 million tonnes CO₂ emissions in 2030, ranging from 271 to 401 million tonnes for the pessimistic and optimistic scenarios, respectively. This article also reports on the supply potential of aviation biofuels (clustered in HEFA/HVOs and biojet) based on the production capacity of facilities around the world and provides an insight on the current and future trends in aviation based on the European and national policies, innovations and state-of-the art technologies that will influence the future of sustainable fuels in aviation.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Triangulation of two methods measuring the impacts of a free-floating carsharing system in Germany

This article reports on two different methods applied in the same survey (N = 1881) to measure the impact of the carsharing system car2go on other transportation modes in Ulm, Germany. The first method calculated how the mobility behavior of respondents would hypothetically be at the present time if car2go was not available. The second method determined the respondents’ past mobility behavior before using car2go. Confounding circumstances were corrected in both approaches through different mechanisms. Comparable methods calculating carsharing impacts have only been applied individually in past studies. This is the first study applying two measurement methods within the same survey, which enables a triangulation. As other influencing parameters were equal (e.g. sampling frame, nonresponse bias, mode of asking, point in time of the survey), the deviating results are assumed to have resulted from the different measurement techniques. The findings indicate a primacy effect (disproportionally high selection of first answer options) having influenced the first measurement and an overestimation of the impact on total kilometers travelled in the second measurement. The comparative findings of this dual-measurement could contribute to research designs of greater precision in future work on carsharing impacts.     

Characteristics of air pollutants at near and far field regions of a national highway located at an industrial complex

This paper presents the characterization of air quality monitored at near field region (NFR) and far field region (FFR) of a national highway located at an industrial complex. The pollutants such as PM₁₀, SO₂ and NO₂ were monitored in two campaigns (11th September to 18th October 2012 and 18th January to 17th February 2013). The 24 h average PM₁₀ concentration at NFR and FFR were found to be 86.69 ± 18.56 μg/m³; 73.16 ± 16.21 μg/m³ and 89.44 ± 18.69 μg/m³; 81.91 ± 16.42 μg/m³, respectively during first and second campaign. In both the campaigns PM₁₀, SO₂ and NO₂ concentration at NFR was higher than FFR. The chemical characterization of PM₁₀ at NFR and FFR indicated the abundance of major elements such as Na (NFR = 30% and FFR = 32%), Ca (NFR = 12% and FFR = 14%) and ions namely NO₃⁻ (NFR = 71% and FFR = 68%) and NH₃⁺ (NFR = 15% and FFR = 19%). Further, at FFR, SO₄²⁻ and NO₃⁻ were found to be 18% and 35% higher than NFR indicating the conversions of SO₂ and NO₂ concentration into secondary particles. The measured SO₂ and NO₂ concentrations were 23 and 21% lower at FFR when compared to NFR confirms the secondary formation.The CALPUFF, EPA regulatory model was set up to understand the dynamics of air pollutants at the industrial complex. The predicted PM₁₀, SO₂ and NO₂ concentrations at NFR and FFR were found to be 32.31 ± 1.56 μg/m³ and 31.35 ± 1.27 μg/m³; 0.37 ± 0.21 μg/m³ and 0.06 ± 0.04 μg/m³; 12.83 ± 6.55 μg/m³ and 4.67 ± 2.77 μg/m³, respectively. The model showed moderate predictions for PM₁₀ (R² = 0.44–0.52), SO₂ (R² = 0.41–0.51) and NO₂ (R² = 0.45–0.61) concentrations.     

Using nonparametrics to specify a model to measure the value of travel time

Using a range of nonparametric methods, the paper examines the specification of a model to evaluate the willingness-to-pay (WTP) for travel time changes from binomial choice data from a simple time–cost trading experiment. The analysis favours a model with random WTP as the only source of randomness over a model with fixed WTP which is linear in time and cost and has an additive random error term. Results further indicate that the distribution of log WTP can be described as a sum of a linear index fixing the location of the log WTP distribution and an independent random variable representing unobserved heterogeneity. This formulation is useful for parametric modelling. The index indicates that the WTP varies systematically with income and other individual characteristics. The WTP varies also with the time difference presented in the experiment which is in contradiction of standard utility theory.     

General statistics of diesel engines’ idle time: Shunting locomotives in industrial sidings in Poland 2009…2013

Shunting locomotive/switcher (AmE)/utilization profiles are analyzed in this paper, in particular on the basis of idle time data collected in nineteen Polish industrial sidings and yards. 40 years old, diesel-electric locomotives are observed during 1000 h. Idle times related to work cycles are analyzed statistically. The percentage of the shunting locomotive daily operating time that the engine is operating at idle amounts to 70% (from 55% to 90%), and average daily idle fuels consumption amounts to 150 l a day (from 90 to 240 l a day).Many European and Asian countries still operate a significant number of similar (ChME3, e.g. S200) old, diesel-electric locomotives (almost 8000 locomotives have been produced), for moving trains over long distances and as shunting locomotives.Observed frequent short idle time periods suggest necessity of widening future scope of idling times’ analysis. Adaptation of Polish rolling stock will be possible using prior general public education about dangerous carcinogens in diesel exhaust smoke and fuel waste related to diesel engines’ idling. Simple simultaneous depiction of diesel engine power time series together with idle time could be used for educational visualization of idling among a wider audience. In the future classical aggregated idle time statistics should be supplemented by models that are more related to the variability of shunting locomotives diesel generator’s power time series, e.g. distribution of frequent short individual idle time cases.     

Inferring price elasticities of car use and moral costs of driving without a licence

The article develops a model which makes it possible to infer drivers’ perceived extra costs per km of driving without a license and the moral costs of doing so. Furthermore, it gives estimates of the ratios between responses to car license suspension in different time perspectives. The calculations are carried out using data over car holders’ willingness to pay for not losing their driving license for 12 months and 24 months, their yearly driving distance and variable car usage costs. The elasticity ratios estimated here are compared with previous studies of short-term and long-term elasticities of car usage with respect to car usage costs.     

Characterization and prediction of air traffic delays

This paper presents a new class of models for predicting air traffic delays. The proposed models consider both temporal and spatial (that is, network) delay states as explanatory variables, and use Random Forest algorithms to predict departure delays 2–24 h in the future. In addition to local delay variables that describe the arrival or departure delay states of the most influential airports and links (origin–destination pairs) in the network, new network delay variables that characterize the global delay state of the entire National Airspace System at the time of prediction are proposed. The paper analyzes the performance of the proposed prediction models in both classifying delays as above or below a certain threshold, as well as predicting delay values. The models are trained and validated on operational data from 2007 and 2008, and are evaluated using the 100 most-delayed links in the system. The results show that for a 2-h forecast horizon, the average test error over these 100 links is 19% when classifying delays as above or below 60 min. Similarly, the average over these 100 links of the median test error is found to be 21 min when predicting departure delays for a 2-h forecast horizon. The effects of changes in the classification threshold and forecast horizon on prediction performance are studied.     

Maximizing net benefits for conventional and flexible bus services

Transit ridership is usually sensitive to fares, travel times, waiting times, and access times, among other factors. Therefore, the elasticities of demand with respect to such factors should be considered in modeling bus transit services and must be considered when maximizing net benefits (i.e. “system welfare” = consumer surplus + producer surplus) rather just minimizing costs. In this paper welfare is maximized with elastic demand relations for both conventional (fixed route) and flexible-route services in systems with multiple dissimilar regions and periods. As maximum welfare formulations are usually too complex for exact solutions, they have only been used in a few studies focused on conventional transit services. This limitation is overcome here for both conventional and flexible transit services by using a Real Coded Genetic Algorithm to solve such mixed integer nonlinear welfare maximization problems with constraints on capacities and subsidies. The optimized variables include service type, zone sizes, headways and fares. We also determine the maximum welfare threshold between optimized conventional and flexible services) and explore the effects of subsidies. The proposed planning models should be useful in selecting the service type and optimizing other service characteristics based on local geographic characteristics and financial constraints.     

Sensitive analysis of emission rates in MOVES for developing site-specific emission database

With the rapid social and economic development, vehicle emissions have been identified as a major source of urban air pollutions in China. Therefore, the study on vehicle emission estimations is necessary. In light of the limitation of emission data for establishing a local comprehensive emission database, this paper analyzes the characteristics of emission rates in MOVES released by U.S. Environmental Protection Agency (EPA) to investigate the feasibility and to design a method for developing site-specific emission database. Sensitive analysis for model year, age group and speed interval is performed, and the regularity is concluded. The result shows that emission rates are almost constant with model year, but increase with age groups because of emission deterioration. With respect to speed intervals, the emission rates in 25–50 mph are higher than both those <25 mph and >50 mph in the same VSP (vehicle specific power) bins. In addition, an analysis of local emission data in Beijing is conducted to build the relationship between vehicle activities and emission rates. After that, a comparison of emission rates by VSP bins in MOVES and in local database is conducted in this study. The result shows that the absolute values are different because of regulatory emission standards, fuel quality, and other factors. However, the relative changes described by normalizing emission rates have a good consistency. Hence, the regularities of emission rates by VSP bins in MOVES can be used to develop local emission database in Beijing.