New insight into the wave-induced nonlinear vertical load effects of ultra-large container ships based on experiments

Accurate estimation of the wave-induced extreme hogging vertical bending moment (VBM) is of vital importance for the design of container ships because container ships are normally under hogging conditions in still water. According to the empirical formulas proposed by the classification society rules, the design hogging VBM can be approximately 20 % smaller than the design sagging VBM for vessels with small block coefficients. High-order harmonic components in the vertical load effects, which are induced by the nonlinearities in the hydrodynamic forces and ship hull geometry, contribute to the asymmetry. Previous studies have shown that the nonlinear hydrostatic and Froude–Krylov forces increase the sagging VBM significantly. Current numerical tools are able to reveal this asymmetry to a certain extent. There is, however, little focus on the nonlinear pressure under the bow bottom, which is a more likely contributor to the hogging VBM. Several unexpected phenomena have been observed for large container ships. The wave-frequency sagging and hogging VBMs followed each other closely, and hence did not reflect the significant nonlinear factors as expected. In this paper, the test data of two (8600-TEU and 13000-TEU) ultra-large containership models in both regular and irregular head waves are systematically studied. In regular waves, the influence of the second and third harmonics on the fundamental hogging peaks and sagging troughs is estimated by comparing both the amplitude and phase difference relative to the first harmonic peaks. In irregular waves, the focus is on the statistical characteristics of the wave-induced nonlinear vertical load effects. To achieve a balance between results in regular and irregular waves, the influence of the second harmonics is evaluated through bispectral analysis.     

Investigation on the nonlinear effects of the vertical motions and vertical bending moment for a wave-piercing tumblehome vessel based on a hydro-elastic segmented model test

Although the nonlinear effects of the ship motions, wave-induced loads and structural responses of conventional vessels have been investigated experimentally and numerically in recent years, similar studies on the wave-piercing tumblehome (WPTH) vessels are rare, in spite of the urgent necessary due to their extensive applications. This paper experimentally investigated the nonlinear effects of the vertical motions and vertical bending moment (VBM) for a WPTH vessel based on a hydro-elastic segmented model test. The model test was carried out in head regular waves for three amplitudes, in the towing tank at Harbin Engineering University. Based on the band-pass filter technique, four kinds of decomposed harmonics are defined by mean offset, linear wave-frequency response, nonlinear wave-frequency response and nonlinear high-frequency vibration. Meanwhile, based on mean offset, three kinds of combined responses are defined by considering linear wave-frequency response, nonlinear wave-frequency response and nonlinear high-frequency vibrations step by step. The transfer functions of vertical motions and VBM are presented as function of the incident wave frequency, and the measured data and VBM were compared with numerical calculations for validation. With the method proposed above, the results of VBM are analyzed by focusing on the influences of decomposed harmonics on the amplitudes and asymmetry of combined responses. Strong nonlinear effects are observed in the VBM. The nonlinearity of VBM can be identified by the significant amplitudes of decomposed harmonics, variation of amplitude with the wave amplitude and remarkable asymmetry about the zero axis. The hogging VBM of WPTH vessel can be even larger than the sagging VBM, which is in contrast to the general experiences from conventional vessels. Combined the calculated relative motion with the decomposed and combined histories of VBM, the occurrence of the transient impact and its characteristics are discussed, and these are then used to analyze the unconventional asymmetry of VBM. Furthermore, the influences of the bow shape over the vertical motions and VBM are discussed. At the end of the paper, the uncertainties in the test are provided.     

Time-domain simulation of wave-induced nonlinear motions and loads and its applications in ship design

A nonlinear time-domain formulation for ship motions and wave loads and a nonlinear long-term statistics method are presented and applied to the S175 container ship. The general agreement between model tests and numerical results is very satisfactory. The calculated long-term vertical sagging and hogging moments amidships are comparable to those given by DNV rules. The approach described in this paper can be used as a way of more accurately evaluating extreme wave loads and other nonlinear responses in ship design.     

6750箱集装箱船非线性波激振动和颤振响应分析

本文采用三维时域非线性水弹性方法分析了一艘6750箱集装箱船的水弹性响应以及运动和垂向弯矩特征。通过考虑入射波力、静水恢复力、砰击效应的非线性,研究了在恶劣海况下船体的非线性运动和垂向弯矩响应,同时分析了波激振动及颤振对垂向弯矩的影响。数值计算结果表明:(1)非线性入射波力对运动的影响较小,但是对垂向弯矩的影响较大,使得其有明显的倍频成分,同时中垂弯矩显著大于中拱弯矩。另外,非线性入射波力也引起了明显的非线性波激振动;(2)非线性静水恢复力对运动和载荷的影响均较大,但是没有引起明显的非线性响应。非线性计算的垂荡响应小于线性结果,而纵摇和垂向弯矩响应大于线性结果;(3)砰击效应对运动的影响较小,但对垂向弯矩的影响较大,砰击效应引起了显著的船体弹性高频振动,增大了载荷幅值,但是其引起的合成中垂和中拱幅值相差不大;(4)非线性水动力的作用主要引起垂向弯矩的倍频响应,包括倍频可能引起的二节点垂向弯矩弹性共振,而砰击效应主要引起船体二节点垂向弯矩共振;(5)本文的非线性水弹性响应计算结果与Kim给出的数值计算结果吻合很好。     

极端波浪与海洋结构物的强非线性作用研究综述

鉴于极端波浪的极大破坏力,其与海洋结构物的强非线性作用研究正日益受到重视。为了评估极端波浪可能带来的严重破坏,有必要对极端波浪作用下海洋结构物的波浪爬升与抨击、强非线性波浪力、结构载荷与运动响应等问题开展深入研究。国内外许多学者采用数值计算、模型实验及小波分析等手段对这些问题开展了探索研究,获得了一些有益的研究结论。该文对极端波浪与海洋结构物相互作用的研究现状和现有结论作了综述,可为进一步开展深入研究提供有益参考。     

Nonlinear analysis of parametric rolling in longitudinal and quartering seas with realistic modeling of roll-restoring moment

Parametric rolling of a containership in longitudinal and quartering seas is examined by applying nonlinear dynamics to a 1DOF mathematical model with realistic modeling of the wave effect on roll-restoring moment. In our previous work, we confirmed that a mathematical model with a roll-restoring moment in waves calculated with the Froude–Krylov assumption could considerably overestimate the danger of capsizing associated with parametric rolling. Therefore, in the present work, all numerical calculations based on nonlinear analysis were carried out with the direct aid of a measured roll-restoring moment in waves. For this purpose, captive model experiments were conducted for various sets of wavelengths in longitudinal seas. This experiment demonstrates that the Froude–Krylov prediction could not explain the wavelength effect on restoring moment as the wave-steepness effect. Using the numerical model with the aid of this measured roll-restoring moment, the Poincaré mapping technique was applied to identify bifurcation structures of roll motions not only in longitudinal seas, but also in quartering seas. As a result, it was confirmed that capsizing associated with parametric rolling is more likely to occur in following seas than in quartering seas. However, period-doubling and chaos appeared in quartering seas. Finally, an averaging method assuming a period-2 orbit was applied to the same model with the same conditions as the Poincaré map. Reasonably good agreement was obtained between the numerical results with a Poincaré map and those with the averaging method in longitudinal seas, but the averaging method has limited capability in quartering seas.     

顶浪、斜浪中复合材料双体艇艇体结构耦合响应数值分析

采用流固耦合（Fluid-Structure Interaction,FSI）的艇体波浪载荷和结构响应的数值分析方法,对顶浪、斜浪中复合材料双体艇结构的动态响应进行研究。分别建立了完整的复合材料艇体有限元模型以及流场模型,基于数值水池造波技术,通过计算获得了顶浪、斜浪中复合材料艇体结构的时域动态响应结果,选取高应力梯度区域,通过网格加密重构同时获得了复合材料的层间应力。选取具有代表性的前10大等效应力与内外面板最值主应力,在将 FSI与传统基于经验公式的有限元法（Finite Element Method,FEM）的结果对比中发现,FSI中拱、中垂的计算结果更接近于 FEM弯扭组合工况,而采用《钢制双体船直接计算指南》计算复合材料双体艇时,所用经验公式的顶浪航行波浪载荷计算值偏小。     

基于一个二维修正水弹性方法的集装箱船体梁动态前极限强度评估研究

海上极端波因其巨大的波高常常导致船体的极限破坏。该文提出了一个二维的修正水弹性方法来研究一个集装箱船船体梁在极端波中的动态前极限强度。传统的极限强度评估基于准静态方法,没有动态效应被考虑。而船体在波浪下的动态结构响应是基于水弹性方法,传统的水弹性方法并不能计算船体梁的动态非线性强度。该二维修正的水弹性方法考虑时域波浪和非线性船体梁之间的耦合,将水弹性方法和Smith方法结合,用Smith方法计算船体梁的刚度,而其刚度与船体梁的强度和变形曲率有关。所以该时域的非线性刚度被用于修改水弹性方法里的常数项的结构梁刚度。几组极端波模型被用以产生船体梁的大变形和非线性动态垂向弯矩。文中分别采用修正水弹性方法和普通水弹性方法,通过改变四个重要的极端波参数如极端波最大波高、规则波的波高、波速和波长等来研究其对船体梁船中处的大变形转角和非线性垂向弯矩的影响,通过采用修正的水弹性方法计算得来的结果与水弹性方法计算得来的结果相比较,得到了一些差异和结论。     

小方型系数船舶的船体波浪载荷综合研究

从船级社规范对于不符合主尺度比要求的船舶船体梁波浪载荷的规定出发,采用理论预报和船模试验2种综合方式,进行了小于0.6方型系数、高航速、高海况目标船的波浪载荷研究.从规范对波浪载荷的线性理论预报值进行的非线性修正,修正后中拱和中垂波浪弯矩绝对值之和与线性理论预报极值全幅值相等出发,阐述所研究船特殊主尺度比下的模型试验结果、三维非线性水弹性理论预报结果显示出的波浪载荷非线性行为;同时综合模型试验与理论预报的共同规律,研究不同波高、航速、浪向等非常规船型船体波浪载荷的强非线性行为,从而认为规范基于的线性理论预报值进行非线性修正的统一规定太过笼统,进而建议规范对波浪载荷的非线性修正予以进一步的明确区分和规定.     

Importance of several nonlinear factors on broaching prediction

In order to realize a more quantitative prediction of broaching and capsizing in following and quartering seas, existing mathematical modelling techniques should be upgraded. Therefore, it is necessary to systematically examine all factors relevant to capsizing in following and quartering seas. To this end, we first attempted to examine the prediction accuracy of wave-induced forces by comparing calculations with captive model experiments. As a result, we found that a wave-induced surge force has a certain nonlinearitiy with respect to wave steepness. The nonlinearity of sway–roll coupling with respect to sway velocity was also found, and our numerical result with these nonlinearities improves the prediction accuracy of the critical ship speed of capsizing in following and quartering seas. The importance of the wave effect on propeller thrust was also examined. We found that this effect is not negligibly small and could improve capsizing predictions in heavy following and quartering seas. Finally, we attempted to investigate the importance of nonlinear heel-induced hydrodynamic forces on numerical predictions of capsizing due to broaching. Here, we propose a new procedure for captive model experiments to obtain hydrodynamic forces with various heel angles up to 90°, and data on heel-induced hydrodynamic forces with respect to heel angle in calm water are provided. We then compare the numerical simulations with the nonlinear heel-induced hydrodynamic forces and without them. These time series comparisons show that the effect of nonlinear heel-induced hydrodynamic forces in calm water is not negligibly small for the case of ship capsizing due to broaching.     

Experimental and numerical study of containership responses in severe head seas

An accurate determination of the global load effects in a ship is vital for the design of the vessel. This paper addresses an experimental and numerical study of containership responses in severe head seas. Experimental results were obtained using a flexible model of a containership of newer design. The experiments showed that, taking hull flexibility into account, the fourth and sixth harmonic of the vertical bending moments had a maximum value of between 25% and 50% of the first harmonic. We also demonstrated that hull flexibility can increase the vertical bending moment by up to 35% in sea states relevant for design. Comparisons of moments found experimentally with results from a nonlinear hydroelastic strip theory method showed that the effect of nonlinearities on the rigid body moments was slightly over-predicted in the aft body. The method also tends to over-predict the increase of the bending moments due to hull flexibility. In general however, the numerical results compared reasonably well with the experimental ones.     

Numerical and experimental investigations into the application of response conditioned waves for long-term nonlinear analyses

The coefficient of contribution method, in which the extreme response is determined by considering only the few most important sea states, is an efficient way to do nonlinear long-term load analyses. To furthermore efficiently find the nonlinear short-term probability distributions of the vessel responses in these sea states, response conditioned wave methods can be used. Several researchers have studied the accuracy of response conditioned wave methods for this purpose. However, further investigations are necessary before these can become established tools. In this paper we investigate the accuracy by comparing the short-term probability distributions obtained from random irregular waves with those from response conditioned waves. We furthermore show how response conditioned wave methods can be fitted into a long-term response analysis. The numerical and experimental investigations were performed using a container vessel with a length between perpendiculars of 281 m. Numerical simulations were done with a nonlinear hydroelastic time domain code. Experiments were carried out with a flexible model of the vessel in the towing tank at the Marine Technology Centre in Trondheim. The focus was on the probability distributions of the midship vertical hogging bending moments in the sea states contributing most to the hogging moments with a mean return period of 20 years and 10 000 years. We found that the response conditioned wave methods can very efficiently be used to accurately determine the nonlinear short-term probability distributions for rigid hulls, but either accuracy or efficiency is to a large effect lost for flexible hulls, when slamming induced whipping responses are accounted for.     

Parametrical studies of a new numerical model for controlled ship motions in extreme astern seas

Parametrical studies based on numerical simulations were carried out for very steep regular waves to assess possible improvements in the state-of-the art numerical modelling of the control and capsizing behaviour of ships in following and quartering seas. A nonlinear 6-DOF numerical model has been developed with the inclusion of frequency-dependent terms, the so called memory effects, and a flexible axis system that allows straightforward combination of seakeeping and manoeuvring models while accounting for extreme motions. The previously undertaken validation analyses using extensive model test data provided qualitatively good agreement, whereas the comparison with numerical models without coupling of the vertical motions and frequency-dependent hydrodynamic terms embodied in radiation forces identified improvements in the accuracy. However, to broaden the assessment of the numerical model, further parametrical numerical analyses were carried out using two ships, which had previously been tested in the validation analyses, for various operational and environmental conditions. These parameters were changed in accordance with the recommendations from international organisations and experience from model tests to realise and avoid dangerous conditions that often result in capsizing, such as broaching associated with surf riding and low-cycle resonance. As a result of the parametric analysis, we discuss the sensitivity of the improvements in the numerical model for various critical operational and design parameters and its possible use to provide a link between the ship's behavior and these parameters.     

水下爆炸作用下对称结构船体梁整体损伤特性研究

基于相似原则设计了全封闭对称结构船体梁模型,将TNT炸药置于模型中部正下方爆炸,通过改变爆距和药量来研究梁模型在水下近距非接触爆炸作用下的整体损伤特性,比较爆炸气泡运动对梁结构造成的中垂和中拱弯曲损伤作用,探索近距条件下炸药爆炸造成梁发生整体损伤变形时的高效攻击方式。研究发现:在近距非接触爆炸作用下,当爆炸气泡脉动频率与梁一阶湿频率相近时,水下爆炸气泡对梁结构造成的损伤作用以中垂弯曲为主,且爆径比越小,中垂损伤作用越明显;若爆径比不变,随着药量的增大,梁的整体损伤模式会由中垂弯曲向中拱弯曲转变;一定爆距范围内,炸药在远距离多次爆炸比近距离一次爆炸所造成的梁结构中垂损伤变形要大。     

Experimental study on the nonlinear pressure acting on a high-speed vessel in regular waves

It is well known that the hydrodynamic responses of a high-speed vessel traveling in regular head waves of even moderate wave height can show significant nonlinear behavior, and so linear statistical techniques become insufficient for predicting the statistics of responses in irregular waves. On the other hand, it has been shown that an approximate third-order Volterra model is applicable to handling the statistics of some nonlinear seakeeping problems, such as motions and vertical hull girder loads. In the present study, the focus is on the nonlinear behavior of the pressure responses of the hull surface, especially on the pressures acting on alternately wet and dry areas near the waterline and on the bow zone with high deadrise angles that may be subject to slight impact and water pile-up effects. To clarify the validity of applying Volterra modeling to this problem, a series of experiments in regular and irregular head waves were carried out, and approximate third-order and fifth-order Volterra models with the proposed algorithm for finding frequency response functions (FRFs) were applied as a means of validation. In the present article, the first part of the validation was performed using experimental data in regular waves. It was confirmed that the third-order Volterra model has adequate accuracy to simulate deterministically the variation of pressure responses in regular waves of different wave steepness up to a wave amplitude to wavelength ratio of 0.01 even for the highly nonlinear pressures acting on the above-mentioned areas of the hull surface.     

Extreme value prediction of nonlinear ship loads by FORM using Prolate Spheroidal Wave Functions

In this study, a method for predicting the extreme value distribution of the Vertical Bending Moment (VBM) in a flexible ship under a given short-term sea state is presented. The First Order Reliability Method (FORM) is introduced to evaluate the Probability of Exceedances (PoEs) of extreme VBM levels. The Karhunen-Loeve (KL) representation of stochastic ocean wave is adopted in lieu of the normal wave representation using the trigonometric components, by introducing the Prolate Spheroidal Wave Functions (PSWFs) to formulate the wave elevations. By this means, reduction of the number of stochastic variables to reproduce ocean wave is expected, which in turn the number of computations required during FORM based prediction phases is significantly reduced. In this study, the Reduced Order Model (ROM), which was developed in our previous studies, is used to yield the time-domain VBMs along with the hydroelastic (whipping) component in a ship. Two different short-term sea states, moderate and severe ones, are assumed. The FORM based predictions using PSWF for normal wave-induced VBM are then validated by comparing with those using the normal trigonometric wave representation and Monte Carlo Simulations (MCSs). Through a series of numerical demonstrations, the computational efficiency of the FORM based prediction using PSWF is presented. Then, the validation is extended to the severe sea state where the whipping vibration contributes to the extreme VBM level to a large degree, and finally the conclusions are given.     

Large-amplitude motion responses of a Ro–Ro ship to regular oblique waves in intact and damaged conditions

This article presents a nonlinear time-domain simulation method for the prediction of large-amplitude motions of a Ro–Ro ship in regular oblique waves in an intact and a damaged condition. Numerical computations and model tests have been carried out to investigate the dynamic motion responses of Ro–Ro ship Dextra to various wave amplitudes at three different wave headings. The results of numerical and experimental investigations for stern quartering waves are reviewed. Comparisons between predictions and measurements show good agreement except in the roll-resonant region. Nonlinear effects are significant in horizontal modes of motion, and resonant roll motion, and there is strong coupling between all modes of motion in the roll-resonant region for large-amplitude responses. On the other hand, the time-domain simulation technique suffers from numerical drift in horizontal modes of motion as wave amplitude increases. This is due to nonlinear equations of motion and the lack of a restoring force and moment in horizontal motion. Received: April 30, 2002 / Accepted: August 9, 2002 Acknowledgments. II Programme of the European Community Commission under contract No. BRPR-CT97-0513. Address correspondence to: H.S. Chan (hoi-sang.chan@ncl.ac.uk)     

Numerical computation of motions and structural loads for large containership using 3D Rankine panel method

In this paper, we present the results of our numerical seakeeping analyses of a 6750-TEU containership, which were subjected to the benchmark test of the 2 nd ITTC–ISSC Joint Workshop held in 2014. We performed the seakeeping analyses using three different methods based on a 3D Rankine panel method, including 1) a rigid-body solver, 2) a flexible-body solver using a beam model, and 3) a flexible-body solver using the eigenvectors of a 3D Finite Element Model(FEM). The flexible-body solvers adopt a fully coupled approach between the fluid and structure. We consider the nonlinear Froude–Krylov and restoring forces using a weakly nonlinear approach. In addition, we calculate the slamming loads on the bow flare and stern using a 2D generalized Wagner model. We compare the numerical and experimental results in terms of the linear response, the time series of the nonlinear response, and the longitudinal distribution of the sagging and hogging moments. The flexible-body solvers show good agreement with the experimental model with respect to both the linear and nonlinear results, including the high-frequency oscillations due to springing and whipping vibrations. The rigid-body solver gives similar results except for the springing and whipping.     

Stability assessment for intact ships in the light of model experiments

A systematic method for assessing intact ship stability with a free-running model in a seakeeping and maneuvering basin is proposed in this paper. Model experiments were carried out in extremely steep regular waves for a model drifting, running in head seas, and quartering seas. This method was applied to two purse seiners, and efficiently identified thresholds in metacentric heights for capsizing of these ships. These capsizing thresholds are compared with requirements of the IMO Code on Intact Stability. This series of model experiments also confirms that capsizing at the threshold occurs only in quartering seas, and shows that capsizing is caused by broaching, loss of stability on a wave crest, or bow diving. Received for publication on Jan. 20, 1999; accepted on July 6, 1999     

Vertical and horizontal bending moments on the hydroelastic response of a large-scale segmented model in a seaway

Wave-induced vertical bending moment (VBM) and horizontal bending moment (HBM) on a large-scale segmented model with a box-type backbone beam in short-crested irregular seas are systematically analyzed using sea trial measurement data. New insights into the relationship between nonlinear VBM and HBM of the ship sailing in short-crested sea waves are explored and presented. The results indicate that the HBM significantly contributes to the total sectional loads when the ship is sailing in a seaway and the HBM has a strong correlation with VBM in both magnitude and tendency. Therefore, design loads of HBM and the corresponding lateral structural strength issues should also be concerned in addition to VBM at the ship design phase.