Effect of road width and traffic volume on vehicular interactions in heterogeneous traffic

Highway traffic flow phenomena involve several complex and stochastic variables with high interdependencies. The variations in roadway, traffic and environmental factors influence the traffic flow quality significantly. Capacity analysis of road sections under different traffic and geometric conditions need to quantify the vehicles of widely varying characteristics to a common and universally acceptable unit. Passenger car unit (PCU) is the universally adopted unit of traffic volume, keeping the passenger car as the ‘standard vehicle’ with reference to its static and dynamic characteristics; other vehicles are expressed to its equivalent number in terms of PCUs. The studies carried out in this aspect represent the dynamic nature of impedance caused by a vehicle while moving through a traffic stream. The PCU values recommended by the Highway Capacity Manual are widely applied in many countries; however, their applicability is highly under debate because of the variations in prevailing local traffic conditions. There are several factors that influence the PCU values such as traffic, roadway, vehicle, environmental and control conditions, etc. Apart from vehicular characteristics, the other two major factors that influence the PCU of vehicles are the following: (i) road width and (ii) traffic volume. In this study, estimation of PCU values for the different types of vehicles of a highly heterogeneous traffic on 7.5‐ and 11.0‐m‐wide roads, using micro‐simulation technique, has been dealt with. It has been found that the PCU value of a vehicle type varies significantly with variation in road width and traffic volume. The results of the study indicate that the PCU values are significantly influenced by the said two factors. Copyright © 2012 John Wiley & Sons, Ltd.     

A Cooperative Intelligent Transport Systems (C‐ITS)‐based lane‐changing advisory for weaving sections

Weaving sections, a common design of motorways, require extensive lane‐change manoeuvres. Numerous studies have found that drivers tend to make their lane changes as soon as they enter the weaving section, as the traffic volume increases. Congestion builds up as a result of this high lane‐changing concentration. Importantly, such congestion also limits the use of existing infrastructure, the weaving section downstream. This behaviour thus affects both safety and operational aspects. The potential tool for managing motorways effectively and efficiently is cooperative intelligent transport systems (C‐ITS). This research investigates a lane‐change distribution advisory application based on C‐ITS for weaving vehicles in weaving sections. The objective of this research is to alleviate the lane‐changing concentration problem by coordinating weaving vehicles to ensure that such lane‐changing activities are evenly distributed over the existing weaving length. This is achieved by sending individual messages to drivers based on their location to advise them when to start their lane change. The research applied a microscopic simulation in aimsun to evaluate the proposed strategy's effectiveness in a one‐sided ramp weave. The proposed strategy was evaluated using different weaving advisory proportions, traffic demands and penetration rates. The evaluation revealed that the proposed lane‐changing advisory has the potential to significantly improve delay. Copyright © 2016 John Wiley & Sons, Ltd.     

Impact of heavy vehicles on surrounding traffic characteristics

This work examines the impact of heavy vehicle movements on measured traffic characteristics in detail. Although the number of heavy vehicles within the traffic stream is only a small percentage, their impact is prominent. Heavy vehicles impose physical and psychological effects on surrounding traffic flow because of their length and size (physical) and acceleration/deceleration (operational) characteristics. The objective of this work is to investigate the differences in traffic characteristics in the vicinity of heavy vehicles and passenger cars. The analysis focuses on heavy traffic conditions (level of service E) using a trajectory data of highway I‐80 in California. The results show that larger front and rear space gaps exist for heavy vehicles compared with passenger cars. This may be because of the limitations in manoeuvrability of heavy vehicles and the safety concerns of the rear vehicle drivers, respectively. In addition, heavy vehicle drivers mainly keep a constant speed and do not change their speed frequently. This work also examines the impact of heavy vehicles on their surrounding traffic in terms of average travel time and number of lane changing manoeuvres using Advanced Interactive Microscopic Simulator for Urban and Non‐Urban Networks (AIMSUN) microscopic traffic simulation package. According to the results, the average travel time increases when proportion of heavy vehicles rises in each lane. To reflect the impact of heavy vehicles on average travel time, a term related to heavy vehicle percentage is introduced into two different travel time equations, Bureau of Public Roads and Akçelik's travel time equations. The results show that using an exclusive term for heavy vehicles can better estimate the travel times for more than 10%. Finally, number of passenger car lane changing manoeuvres per lane will be more frequent when more heavy vehicles exist in that lane. The influence of heavy vehicles on the number of passenger car lane changing is intensified in higher traffic densities and higher percentage of heavy vehicles. Large numbers of lane changing manoeuvres can increase the number of traffic accidents and potentially reduce traffic safety. The results show an increase of 5% in the likelihood of accidents, when percentage of heavy vehicles increases to 30% of total traffic. Copyright © 2014 John Wiley & Sons, Ltd.     

Passing Bays for Slow Moving Vehicles on Rural Two‐lane Roads

Abstract

Slow‐moving vehicles, including agricultural vehicles, on arterial highways can cause serious delays to other traffic as well as posing an extra safety risk. This paper elaborates on a small‐scale solution for these problems: the passing bay. It investigates the impacts of a passing bay on the total delay for other motorized vehicles, the number of passing manoeuvres and hindered vehicles, and the mean delay per hindered vehicle. The latter is also considered to be an indicator for traffic safety. The calculations are performed for two characteristic trips with a slow‐moving vehicle. The passing bay is an effective solution to reducing delays on arterial highways when two‐way hourly volumes exceed 600–1000 vehicles. The effects depend on the trip length and speed of the slow‐moving vehicle, and on the passing sight distance limitations of the road. A distance of 2–4?km between the passing bays seems an acceptable compromise between the reduction of delay for other motorized vehicles and the extra discomfort and delay for drivers of slow‐moving vehicles. This result also shows that passing bays are not effective in regions where slow‐moving vehicles mainly make trips shorter than this distance.     

Modelling heavy vehicle car‐following behaviour in congested traffic conditions

This study develops a car‐following model in which heavy vehicle behaviour is predicted separately from passenger car. Heavy vehicles have different characteristics and manoeuvrability compared with passenger cars. These differences could create problems in freeway operations and safety under congested traffic conditions (level of service E and F) particularly when there is high proportion of heavy vehicles. With increasing numbers of heavy vehicles in the traffic stream, model estimates of the traffic flow could be degrades because existing car‐following models do not differentiate between these vehicles and passenger cars. This study highlighted some of the differences in car‐following behaviour of heavy vehicle and passenger drivers and developed a model considering heavy vehicles. In this model, the local linear model tree approach was used to incorporate human perceptual imperfections into a car‐following model. Three different real world data sets from a stretch of freeway in USA were used in this study. Two of them were used for the training and testing of the model, and one of them was used for evaluation purpose. The performance of the model was compared with a number of existing car‐following models. The results showed that the model, which considers the heavy vehicle type, could predict car‐following behaviour of drivers better than the existing models. Copyright © 2013 John Wiley & Sons, Ltd.     

An applicatoin of an optimal traffic control during lane closure periods of a two‐lane road

On two‐lane roadways, when provision should be made for alternative one‐way movement (for construction or maintenance), the traffic characteristics differ from normal operation in which no lane is closed. The purpose of this study is to derive optimal strategies for controlling, by means of traffic signals, the one lane operation (in two‐way roadways). In this study, strategies to determine the optimal length of the closed one‐lane section during construction and maintenance work are established. This length minimizes the objective function representing the tradeoff between delay cost and operational cost. Using the length value obtained by the proposed model, plus a timing methodology, the overall cost of operating the closed highway section can be minimized. The sensitivity analysis of the optimal solution for the section length is examined with respect to the input variables. This analysis shows that for very low traffic flow values (less than 100 vph per direction), the solution is very sensitive to fuel price changes, while for greater flow values, the solution is insensitive to this change. Similar results are obtained for changes in the worker's wage which is part of both the operational and the delay cost. That is, the section's length is sensitive to wage changes at low traffic flow and insensitive otherwise. Based on the results presented in this study, it is possible to establish a guideline for the section's length determination. The control measure can emerge from a pair of traffic signals that can be installed at both ends of the closed highway segment. This traffic control system is also described in the study in terms of its components and operational features and advantages.     

A novel approach for assessing the LOS for two‐lane intercity highways under heterogeneous traffic conditions

Performance of two‐lane intercity highways has been evaluated in terms of level of service (LOS) by different researchers. Different follower‐related performance measures, namely, the number of followers (NF), percent followers (PF), follower density (FD) and the number of followers as a proportion of capacity (NFPC) are examined in the present study to define LOS. Data are collected from five sites located in different parts of India. While almost all the past studies used 3‐s headway rule to identify followers suggested by US Highway Capacity Manual, a new methodology is proposed in the current study to identify the followers by analysing speed difference (SD) and the gap between two consecutive vehicles. It is observed that vehicles travel in non‐following condition after a critical gap threshold value of 10 s. By using a SD limit of ?4 km/h to +10 km/h and a gap value of 10 s, followers are identified across all the study sites. Thereafter, different critical gap values ranging from 1.9 s to 4.3 s are observed at the study sites beyond which the probability of not following would increase. Variation in two‐way traffic volume is found to be the main contributory factor which affects the critical gap values. Among all of the performance measures, NFPC shows a strong correlation with two‐way traffic volume followed by FD under heterogeneous traffic condition. Finally, different threshold values of LOS ranges for two‐lane intercity highways are provided by carrying out cluster analysis with the help of NFPC and FD. Copyright © 2017 John Wiley & Sons, Ltd.     

山区高速公路危险路段交通安全设施系统研究

本篇以高速公路长下坡危险路段为研究对象,以解决云南蒙新高速公路38km连续长下坡路段行车安全问题为目标,提出了车辆制动失灵概率的预测方法,研发出了长下坡路段制动失灵车辆专用减速带、消能减速护栏、网索式避险车道等三种新型安全设施,并总结分析了长下坡路段安全设施的设计方法及施工工艺技术,编制了《连续长下坡路段安全保障系统设计与施工指南》,可有效提高长下坡危险路段的行车安全。     

Modeling delay at signalized intersections with channelized right‐turn lanes considering the impact of blockage

This paper presents a probabilistic delay model for signalized intersections with right‐turn channelization lanes considering the possibility of blockage. Right‐turn channelization is used to improve the capacity and to reduce delay at busy intersections with a lot of right‐turns. However, under heavy traffic conditions the through vehicles will likely block the channelization entrance that accrues delay to right‐turn vehicles. If the right‐turn channelization gets blocked frequently, its advantage in reducing the intersection delay is neglected and as a result the channelization lane becomes inefficient and redundant. The Highway Capacity Manual (HCM) neglects the blockage effect, which may be a reason for low efficiency during peak hours. More importantly, using HCM or other standard traffic control methods without considering the blockage effects would lead to underestimation of the delay. To overcome this issue, the authors proposed delay models by taking into account both deterministic and random aspects of vehicles arrival patterns at signalized intersections. The proposed delay model was validated through VISSIM, a microscopic simulation model. The results showed that the proposed model is very precise and accurately estimates the delay. In addition, it was found that the length of short‐lane section and proportion of right‐turn and through traffic significantly influence the approach delay. For operational purposes, the authors provided a step‐by‐step delay calculation process and presented approach delay estimates for different sets of traffic volumes, signal settings, and short‐lane section lengths. The delay estimates would be useful in evaluating adequacy of the current lengths, identifying the options of extending the short‐lane section length, or changing signal timing to reduce the likelihood of blockage. Copyright © 2016 John Wiley & Sons, Ltd.     

Vehicle reidentification and travel time measurement on congested freeways

The paper presents an algorithm for matching individual vehicles measured at a freeway detector with the vehicles’ corresponding measurements taken earlier at another detector located upstream. Although this algorithm is potentially compatible with many vehicle detector technologies, the paper illustrates the method using existing dual-loop detectors to measure vehicle lengths. This detector technology has seen widespread deployment for velocity measurement. Since the detectors were not developed to measure vehicle length, these measurements can include significant errors. To overcome this problem, the algorithm exploits drivers’ tendencies to retain their positions within dense platoons. The otherwise complicated task of vehicle reidentification is carried out by matching these platoons rather than individual vehicles. Of course once a vehicle has been matched across neighboring detector stations, the difference in its arrival time at each station defines the vehicle’s travel time on the intervening segment.Findings from an application of the algorithm over a 1/3 mile long segment are presented herein and they indicate that a sufficient number of vehicles can be matched for the purpose of traffic surveillance. As such, the algorithm extracts travel time data without requiring the deployment of new detector technologies. In addition to the immediate impacts on traffic monitoring, the work provides a means to quantify the potential benefits of emerging detector technologies that promise to extract more detailed information from individual vehicles.     

Empirical analysis of heterogeneous traffic flow and calibration of porous flow model

Heterogeneous traffic flow, characterized by a free inter-lane exchange, has become an important issue in addressing congestion in urban areas. It is of particular interest in many developing countries, that experience a strong increase in motorcycle use. New approaches to the heterogeneous non-lane-based flow have been proposed. However insufficient empirical verification has been made to estimate vehicle interaction, that is necessary for an accurate representation of mixed-flow conditions. In this paper, we focus on the porous flow approach to capture the complex interactions. The parameters from this approach are estimated from empirical observations. Video data was recorded and processed to capture vehicle interactions at a number of road sections in Surabaya City, Indonesia. The specific behavior of each vehicle in the traffic flow was captured by developing the pore size–density distributions, analyzing the class-specific critical pore sizes, and producing the class specific speed–density and flow–density diagrams. The results reveal how critical pore sizes are based on pore size–density distributions, the flow diagram for each vehicle class, and how traffic flow relationships for motorcyclists and the other vehicles exhibit significant differences. It is concluded that the proposed approach can represent the specific behavior of the motorcyclist in heterogeneous traffic flow, in both the situations of with- and without an exclusive lane for motorcycles, can clarify motorcyclist’s behavior in terms of passenger car unit of motorcycle, and can therefore support policy making on the improvement of urban transport.     

A revised branch‐and‐price algorithm for dial‐a‐ride problems with the consideration of time‐dependent travel cost

Developing demand responsive transit systems are important with regard to meeting the travel needs for elderly people. Although Dial‐a‐ride Problems (DARP) have been discussed for several decades, most researchers have worked to develop algorithms with low computational cost under the minimal total travel costs, and fewer studies have considered how changes in travel time might affect the vehicle routes and service sequences. Ignoring such variations in travel time when design vehicle routes and schedules might lead to the production of inefficient vehicle routes, as well as incorrect actual vehicle arrival times at the related nodes. The purpose of this paper is to construct a DARP formulation with consideration of time‐dependent travel times and utilizes the traffic simulation software, DynaTAIWAN, to simulate the real traffic conditions in order to obtain the time‐dependent travel time matrices. The branch‐and‐price approach is introduced for the time‐dependent DARP and tested by examining the sub‐network of Kaohsiung City, Taiwan. The numerical results reveal that the length of the time window can significantly affect the vehicle routes and quantitative measurements. As the length of the time window increases, the objective value and the number of vehicles will reduce significantly. However, the CPU time, the average pickup delay time, the average delivery delay time and the average actual ride time (ART)/direct ride time (DRT) will increase significantly as the length of the time window increases. Designing the vehicle routes to reduce operating costs and satisfy the requirements of customers is a difficult task, and a trade‐off must be made between these goals. Copyright © 2014 John Wiley & Sons, Ltd.     

Experimental and empirical investigations of traffic flow instability

Traffic instability is an important but undesirable feature of traffic flow. This paper reports our experimental and empirical studies on traffic flow instability. We have carried out a large scale experiment to study the car-following behavior in a 51-car-platoon. The experiment has reproduced the phenomena and confirmed the findings in our previous 25-car-platoon experiment, i.e., standard deviation of vehicle speeds increases in a concave way along the platoon. Based on our experimental results, we argue that traffic speed rather than vehicle spacing (or density) might be a better indicator of traffic instability, because vehicles can have different spacing under the same speed. For these drivers, there exists a critical speed between 30 km/h and 40 km/h, above which the standard deviation of car velocity is almost saturated (flat) along the 51-car-platoon, indicating that the traffic flow is likely to be stable. In contrast, below this critical speed, traffic flow is unstable and can lead to the formation of traffic jams. Traffic data from the Nanjing Airport Highway support the experimental observation of existence of a critical speed. Based on these findings, we propose an alternative mechanism of traffic instability: the competition between stochastic factors and the so-called speed adaptation effect, which can better explain the concave growth of speed standard deviation in traffic flow.     

Evaluating the effects of automated vehicle technology on the capacity of freeway weaving sections

Weaving sections, where a merge and a diverge are in close proximity, are considered as crucial bottlenecks in the highway network. Lane changes happen frequently in such sections, leading to a reduced capacity and the traffic phenomenon known as capacity drop. This paper studies how the emerging automated vehicle technology can improve the operations and increase the capacity of weaving sections. We propose an efficient yet effective multiclass hybrid model that considers two aspects of this technology in scenarios with various penetration rates: (i) the potential to control the desired lane change decisions of automated vehicles, which is represented in a macroscopic manner as the distribution of lane change positions, and (ii) the lower reaction time associated with automated vehicles that can reduce headways and the required gaps for lane changing maneuvers. The proposed model is successfully calibrated and validated with empirical observations from conventional vehicles at a weaving section near the city of Basel, Switzerland. It is able to replicate traffic dynamics in weaving sections including the capacity drop. This model is then applied in a simulation-based optimization framework that searches for the optimal distribution of the desired lane change positions to maximize the capacity of weaving sections. Simulation results show that by optimizing the distribution of the desired lane change positions, the capacity of the studied weaving section can increase up to 15%. The results also indicate that if the reaction time is considered as well, there is an additional combined effect that can further increase the capacity. Overall, the results show the great potential of the automated vehicle technology for increasing the capacity of weaving sections.     

A probabilistic model for the behaviour of traffic at a roundabout

A discrete-time, Markov chain model is proposed to describe the behaviour of traffic travelling on a single-lane roundabout and queueing on approach roads to enter the roundabout. A general origin-destination matrix is allowed for trip ends, there is an arbitrary number of approach roads and there is room for a general number of vehicles on each weaving section. Attention is given to the equilibrium régime at an approach subject to heavy traffic conditions. It is shown that for such an approach the moments of the distribution of the length of the queue of waiting vehicles may be found by a heavy traffic approximation.     

Integrated expression method for technical mapping of traffic parameters using RGB color model

In the field of traffic flow, speed, density, time, and distance are fundamental variables analyzed to predict traffic conditions. Reliable sources of information are gauged using tested mathematical approaches that have been developed. However, a fundamental diagram that could serve as a basis for expression techniques has not been devised. Red–green–blue (RGB) color modeling was used to overcome this limitation in traffic flow. The purpose of this study is to provide a way to understand traffic flow conditions based on features of three traffic flow elements simultaneously. The limitation of three‐dimensional expressions in two‐dimensional paper was extended to multi‐dimensional information. Information on speed, density, and flow were combined into a single RGB color and given the name RGB flow‐density space time‐distance space. This cancels out the effect of each individual's vehicular trajectories and contains five major components of a specific road section. The new gizmo aims to provide information on traffic flow conditions in transition and to stimulate further approaches related to the predictions and understanding of traffic flow. Copyright © 2016 John Wiley & Sons, Ltd.     

Agricultural vehicles and sustainable safe road traffic: solving conflicts on arterial highways

Addressing the issues of traffic safety in rural areas presents a constant challenge. The mix of light and heavy vehicles and the considerable differences in speed among these traffic participants result in high risks and delays for the faster vehicles. Agricultural vehicles (AVs) in particular have such an impact on traffic, especially when using arterial highways. This paper reviews the problems of safety and delays that AVs cause on arterial highways, and the appropriate mitigation. The concept of 'sustainable safety' in The Netherlands focuses on these problems, because of the proposed construction of parallel roads alongside all arterial highways. However, Dutch accident statistics cannot justify the high costs for the construction of parallel roads alongside 7000 km of arterial highways. Delays experienced by fast traffic are another reason for separating AVs from other road users with parallel roads. Alternative measures alongside the arterial highway, such as passing bays, restricting AVs to travelling at off-peak only and improving the conspicuity of the AVs, may be more cost-effective ways of reducing delays and/or improving traffic safety on arterial highways. Another solution may be to eliminate the need for AVs to use the arterial highway by altering their routes. For this purpose, land reallocation projects (as practised in Holland) can provide a useful tool.     

The measurement of train noise: a case study in northern Italy

This paper analyses the interactions between vehicles, infrastructure and environment for rail traffic. It identifies variables having a significant influence on sound levels, defines a standard procedure for measuring noise, and develops a database for setting up and calibrating train noise models. A pilot study looks at two railway lines passing through Vercelli, a medium sized town in the north-west of Italy. Four main conclusions were drawn. First, in certain conditions, variables that normally influence noise production can be neglected (e.g. when surrounding environmental conditions are constant, different types of train do not cause a significant variation in noise level). Secondly, when diesel trains are travelling at less than 70 km/h, a speed change of 30–40 km/h significantly affects the maximum noise level (Lmax). However, for electrified lines, when speed is below 80 km/h, a change of 20–30 km/h does not cause significant variations in Lmax. Thirdly, for diesel trains transiting at low speeds––e.g. near stations––noise emissions are strongly affected by acceleration/deceleration. Lastly, an approach based on ‘sites types’ is able to produce useful results because site configuration and the presence of building significantly affect Lmax. High buildings along the line can increase noise levels and may nullify the advantages derived from technological advance in the vehicles.     

Safety modeling for two‐way left‐turn lanes and a procedure to identify two‐way left‐turn lane segments with safety concerns

In the past, two‐way left‐turn lane (TWLTL) median treatments have been frequently used in Florida to inexpensively improve traffic and safety performances. In order to identify factors that may have significant impacts on safety operations in TWLTL sections and to identify TWLTL locations that present existing and future safety concerns, a research project was carried out and results are summarized in the paper. In the research, a three‐year crash history database with crashes and section characteristics from a total of 1688 TWLTL sections all over Florida was developed and used. A negative binomial regression model was developed to determine the statistical relationship between the number of crashes per mile per year and several variables such as traffic volume, access density, posted speed, and number of lanes. In regard to the methodology, in order to identify locations with safety concerns, several steps are needed: development of real crash data distribution, determination of statistical distribution models that better represent the actual crash data, determination of percentile values for the average number of crashes, estimation of crash rates for sections with the same characteristics, estimation of critical values for the variables corresponding to the percentile values for average number of crashes, calculation of tables of critical average annual daily traffic values, and generation of a list of TWLTL locations with critical safety concerns. Results presented in the paper have been used in real applications. Copyright © 2012 John Wiley & Sons, Ltd.     

Congestion avoidance in city traffic

The number of vehicles on the road (worldwide) is constantly increasing, causing traffic jams and congestion especially in city traffic. Anticipatory vehicle routing techniques have thus far been applied to fairly small networked traffic scenarios and uniform traffic. We note here a number of limitations of these techniques and present a routing strategy on the assumption of a city map that has a large number of nodes and connectivity and where the vehicles possess highly varying speed capabilities. A scenario of operation with such characteristics has not previously been sufficiently studied in the literature. Frequent short‐term planning is preferred as compared with infrequent planning of the complete map. Experimental results show an efficiency boost when single‐lane overtaking is allowed, traffic signals are accounted for and every vehicle prefers to avoid high traffic density on a road by taking an alternative route. Comparisons with optimistic routing, pessimistic routing and time message channel routing are given. Copyright © 2014 John Wiley & Sons, Ltd.