Handling Analysis of a Motorcycle with Added Cambering of the Front Frame

SUMMARY

Through linear analysis, the handling characteristics of the motorcycle with fixed control of added cambering of front frame are investigated under the variation of fixed and free controls of steering axis. The cornering responses and stability characteristics of the motorcycle are presented with the aid of the handling diagram. From numerical results for a typical motorcycle, it is found that the influence of the cambering of front frame on the cornering response of fixed steering control is opposite to that of free steering control. Moreover, the design philosophy of a so-called semi-direct steering mechanism, which cambers the front frame for cornering, is studied.     

Study on integrated control of active front steer angle and direct yaw moment

This study proposes a control system to improve vehicle handling and stability under severe driving conditions by actively controlling the front steering angle and the distribution of braking forces on four tires. With the application of a model-matching control technique, this proposed control system makes the performance of the actual vehicle model follow that of an ideal vehicle model with consideration of nonlinearity of tire characteristics. Finally, this paper investigates the effectiveness of control system during the following conditions: braked cornering, lane change and side wind disturbance.     

双前桥转向机构优化设计方法研究

双前桥转向机构包含两个独立的转向梯形机构和双前桥间的转向联动机构—双摇臂系统。文中分析了双前桥转向机构应实现的功能、运动规律和与其它系统可能造成的运动干涉,提出了同时保证双前桥汽车车轮转向时做纯滚动和杆系干涉造成的车轮异常磨损最小的多目标优化设计方法。     

四轮转向汽车自适应模型跟踪控制研究

使用单点预瞄驾驶员模型，针对确定性汽车模型探讨了４ＷＳ汽车在单移线行驶过程中后轮的最优转向控制规律。通过引入状态反馈，改善了整车的转向特性，将实际汽车的前后轮胎侧刚度及外界干扰视为有界的不确定性参数，采用自适应模型跟踪变结构控制方法，使得不确定的实际汽车模型能够很好地跟踪确定的最优理论模型，仿真结果表明该方法的可行性，控制系统能够有效地克服参数摄动及外界干扰对系统稳定性的影响。     

A Variable Free Control Characteristic Vehicle

A variable characteristic car (VCC) has been developed at Melbourne University for driverlvehicle handling research. The vehicle is unusual in that it has facilities for varying both its fixed control and free control dynamic characteristics over wide ranges. In this paper the servo systems used to effect these changes are described. The calibration methods used to relate the vehicle response characteristics to the variable servo settings are detailed. Sample calibration results are given for the fixed control parameters steering ratio, yaw response time and stability factor. Calibration of the free control parameters is also described and results are given for the steering torque gradient, and the time-to-peak and percentage overshoot of the steering wheel motion in response to a step input of torque.     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

Nonlinear PI front and rear steering control in four wheel steering vehicles

Vehicle steering dynamics show resonances, which depend on the longitudinal speed, unstable equilibrium points and limited stability regions depending on the constant steering wheel angle, longitudinal speed and car parameters.

The main contribution of this paper is to show that a combined decentralized proportional active front steering control and proportional-integral active rear steering control from the yaw rate tracking error can assign the eigenvalues of the linearised single track steering dynamics, without lateral speed measurements, using a standard single track car model with nonlinear tire characteristics and a non-linear first-order reference model for the yaw rate dynamics driven by the driver steering wheel input. By choosing a suitable nonlinear reference model it is shown that the responses to driver step inputs tend to zero (or reduced) lateral speed for any value of longitudinal speed: in this case the resulting controlled vehicle static gain from driver input to yaw rate differs from the uncontrolled one at higher speed. The closed loop system shows the advantages of both active front and rear steering control: higher controllability, enlarged bandwidth for the yaw rate dynamics, suppressed resonances, new stable cornering manoeuvres, enlarged stability regions, reduced lateral speed and improved manoeuvrability; in addition comfort is improved since the phase lag between lateral acceleration and yaw rate is reduced.

For the designed control law a robustness analysis is presented with respect to system failures, driver step inputs and critical car parameters such as mass, moment of inertia and front and rear cornering stiffness coefficients. Several simulations are carried out on a higher order experimentally validated nonlinear dynamical model to confirm the analysis and to explore the robustness with respect to unmodelled dynamics.     

主动前轮转向客车的操纵稳定性仿真分析

建立某大型客车的含侧向、横摆及侧倾三自由度动力学模型,通过方向盘角阶跃转向仿真结果和试验数据的比较,验证了仿真分析的准确性。采用横摆角速度跟踪主动前轮转向控制策略,结合比例积分控制方法,在考虑作动器动态特性和前轮转角饱和特性的基础上,对主动前轮转向控制前后的车辆进行直线行驶下的侧向风扰动和湿滑路面急转弯情况下的仿真对比分析。结果表明,主动前轮转向控制后的车辆其操纵稳定性和行车安全性都有较大的提高。     

String tyre model for evaluating steering agility performance using tyre cornering force and lateral static characteristics

The cornering force and lateral static characteristics of a tyre are fundamental factors that describe the steering feel for handling performance. However, it is difficult to justify the contribution of each factor when the tyre’s cornering motion is evaluated through subjective assessment. Currently, the relaxation length of Pacejka’s tyre model is close to describing these tyre motions. Therefore, this paper proposes a string tyre model based on the relaxation length in order to represent the steering performance. The proposed method provides a more accurate modelling of the steering agility performance. Therefore, it is possible to use this model to predict the steering response performance, and this is validated through comparison with a real relaxation length.     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

Steering control of motorcycles using steer-by-wire system

This study proposes a steering control method to improve motorcycle handling and stability. Steer-by-wire (SBW) technology is applied to the motorcycle's steering system to remove characteristic difficulties of vehicle maneuvers. By examining computer simulation using a simplified motorcycle model, the actual rolling angle of the SBW motorcycle is controlled to follow the desired rolling angle intended by the rider. A state feedback control such as linear quadratic control gives the SBW vehicle a good follow-through performance compared with proportional-derivative control because it can decouple rolling motion from the other motions, which affect the rolling motion in the strongly coupled motorcycle system.     

The Influence of Structural Flexibilities on the Straight-running Stability of Motorcycles

SUMMARY

A new tyre model for studies of motorcycle lateral dynamics, and three new motorcycle models, each incorporating a different form of structural compliance, are developed. The tyre model is based on “taut string” ideas, and includes consideration of tread width and longitudinal tread rubber distortion and tread mass effects, and normal load variation. Parameter values appropriate to a typical motorcycle tyre are employed. The motorcycle models are for small lateral perturbations from straight running at constant speed, and include (a) lateral compliance of the front wheel in the front forks, (b) torsional compliance of the front forks, and (c) torsional compliance in the rear frame at the steering head about an axis perpendicular to the steering axis.

Results in the form of eigenvalues, indicating modal damping properties and natural frequencies are presented for each model. The properties of four large production machines for a range of forward speeds, and the practicable range of stiffnesses are calculated, and the implications are discussed.

It is concluded that typical levels of structural compliance in models (a) and (c) contribute significantly to the steering behaviour properties of large motorcycles, and their observed behaviour can be understood better in terms of the new results than of those existing previously. Some conclusions relating to optimal structural stiffness properties are also drawn.     

Automatic path-tracking controller of a four-wheel steering vehicle

The present paper proposes an automatic path-tracking controller of a four-wheel steering (4WS) vehicle based on the sliding mode control theory. The controller has an advantage in that the front- and rear-wheel steering can be decoupled at the front and rear control points, which are defined as centres of percussion with respect to the rear and front wheels, respectively. Numerical simulations using a 27-degree-of-freedom vehicle model demonstrated the following characteristics: (1) the automatic 4WS controller has a more stable and more precise path-tracking capability than the 2WS controller, and (2) the automatic 4WS controller has robust stability against system uncertainties such as cornering power perturbation, path radius fluctuation, and cross-wind disturbance.     

单轨车辆驾驶员单点预瞄模型的参数优化

使用ADAMS软件建立摩托车的模型,并利用MATLAB软件建立驾驶员模型,构成驾驶员-车辆模型。采用MATLAB和ADAMS协同仿真,得出单移线和双移线工况实际行驶轨迹和手把力矩、侧倾力矩、转向角、侧倾角、横向加速度等。建立了摩托车移线工况的性能综合评价指标,并用此指标对摩托车在不同运动状况下的性能进行评价。以驾驶员模型反馈系数为设计变量,采用正交设计方法优选出一组参数。     

Handling stability improvement through robust active front steering and active differential control

The design of the integrated active front steering and active differential control for handling improvement of road vehicles is undertaken. The controller design algorithm is based on the solution of a set of linear matrix inequalities that guarantee robustness against a number of vehicle parameters such as speed, cornering and braking stiffnesses. Vehicle plane dynamics are first expressed in the generic linear parameter-varying form, where the above-stated parameters are treated as interval uncertainties. Then, static-state feedback controllers ensuring robust performance against changing road conditions are designed. In a first series of simulations, the performance of the integrated controller is evaluated for a fishhook manoeuvre for different values of road adhesion coefficient. Then, the controller is tested for an emergency braking manoeuvre executed on a split-μ road. In all cases, it is shown that static-state feedback controllers designed by the proposed method can achieve remarkable road handling performance compared with uncontrolled vehicles.     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Fuzzy-logic applied to yaw moment control for vehicle stability

In this paper, we propose a new yaw moment control based on fuzzy logic to improve vehicle handling and stability. The advantages of fuzzy methods are their simplicity and their good performance in controlling non-linear systems. The developed controller generates the suitable yaw moment which is obtained from the difference of the brake forces between the front wheels so that the vehicle follows the target values of the yaw rate and the sideslip angle. The simulation results show the effectiveness of the proposed control method when the vehicle is subjected to different cornering steering manoeuvres such as change line and J-turn under different driving conditions (dry road and snow-covered).     

Automotive Stability and Handling Dynamics in Cornering and Braking Maneuvers

SUMMARY

Automotive steering behaviour is classified for steady-state cornering and the definitions of over-/understeer and stability/instability are well known. In this paper it is intended to apply these definitions to combined cornering and braking maneuvers i.e. to extend the criteria to quasi-steady-state conditions. This way of investigation was chosen because it gives a clear idea of the typical handling behaviour. Furthermore, the vehicle behaviour is analyzed using the cornering stiffness of the axles and front/rear cornering stiffness ratio because this is always of primary significance. The following contribution is based on a theoretical analysis considering the most important non-linear vehicle properties.

The paper deals with two groups of vehicles: single vehicles (passenger cars) and combinations (passenger car/caravan and tractor/semitrailer). In the case of combinations the effect of trailers on the towing vehicles is examined. So, careful attention is paid to the coupling forces, which alter the wheel loads and influence steerability and stability.     

Nonlinear adaptive sliding mode control for vehicle handling improvement via steer-by-wire

This paper proposes a nonlinear adaptive sliding mode control that aims to improve vehicle handling through a Steer-By-Wire system. The designed sliding mode control, which is insensitive to system uncertainties, offers an adaptive sliding gain to eliminate the precise determination of the bound of uncertainties. The sliding gain value is calculated using a simple adaptation algorithm that does not require extensive computational load. Achieving the improved handling characteristics requires both accurate state estimation and well-controlled steering inputs from the Steer-By-Wire system. A second order sliding mode observer provides accurate estimation of lateral and longitudinal velocities while the driver steering angle and yaw rate are available from the automotive sensors. A complete stability analysis based on Lyapunov theory has been presented to guarantee closed loop stability. The simulation results confirmed that the proposed adaptive robust controller not only improves vehicle handling performance but also reduces the chattering problem in the presence of uncertainties in tire cornering stiffness.