Thermodynamic,environmental and economic effects of diesel and biodiesel fuels on exhaust emissions and nano-particles of a diesel engine

In this study, diesel (JIS#2) and various biodiesel fuels (BDF20, BDF50, BDF100) are used to operate the diesel engine at 100 Nm, 200 Nm and full load; while the engine speed is 1800 rpm. The system is experimentally studied, and the energy, exergy, sustainability, thermoeconomic and exergoeconomic analyses are performed to the system. The Engine Exhaust Particle Sizer is used to measure the size distribution of engine exhaust particle emissions. Also, the data of the exhaust emissions, soot, particle numbers, fuel consumptions, etc. are measured. It is found that (i) most of the exhaust emissions (except NO_x) are directly proportional to the engine load, (ii) maximum CO₂ and NO_x emissions rates are generally determined for the BDF100 biodiesel fuel; while the minimum ones are calculated for the JIS#2 diesel fuel. On the other hand, the maximum CO and HC emissions rates are generally computed for the JIS#2 diesel fuel; while the minimum ones are found for the BDF100 biodiesel fuel, (iii) fuel consumptions from maximum to minimum are BDF100 > BDF50 > BDF20 > JIS#2 at all of the engine loads, (iv) particle concentration of the JIS#2 diesel fuel is higher than the biodiesel fuels, (v) soot concentrations of the JIS#2, BDF20 and BDF50 fuels are directly proportional to the engine load; while the BDF100 is inversely proportional, (vi) system has better energy and exergy efficiency when the engine is operated with the biodiesel fuels (vii) sustainability of the fuels are BDF100 > BDF50 > BDF20 > JIS#2, (viii) thermoeconomic and exergoeconomic parameters rates from maximum to minimum are JIS#2 > BDF20 > BDF50 > BDF100.     

Performance and emission characteristics of a spark ignition engine fuelled with butanol isomer-gasoline blends

The heavy reliance on petroleum-derived fuels such as gasoline in the transportation sector is one of the major causes of environmental pollution. For this reason, there is a critical need to develop cleaner alternative fuels. Butanol is an alcohol with four different isomers that can be blended with gasoline to produce cleaner alternative fuels because of their favourable physicochemical properties compared to ethanol. This study examined the effect of butanol isomer-gasoline blends on the performance and emission characteristics of a spark ignition engine. The butanol isomers; n-butanol, sec-butanol, tert-butanol and isobutanol are mixed with pure gasoline at a volume fraction of 20 vol%, and the physicochemical properties of these blends are measured. Tests are conducted on a SI engine at full throttle condition within an engine speed range of 1000–5000 rpm. The results show that there is a significant increase in the engine torque, brake power, brake specific fuel consumption and CO₂ emissions with respect to those for pure gasoline. The butanol isomers-gasoline blends give slightly higher brake thermal efficiency and exhaust gas temperature than pure gasoline at higher engine speeds. The iBu20 blend (20 vol% of isobutanol in gasoline) gives the highest engine torque, brake power and brake thermal efficiency among all of the blends tested in this study. The isobutanol and n-butanol blend results in the lowest CO and HC emissions, respectively. In addition, all of the butanol isomer-gasoline blends yield lower NO emissions except for the isobutanol-gasoline blend.     

Biofuels in aviation: Fuel demand and CO2 emissions evolution in Europe toward 2030

This article presents the results of a scenario-based study carried out at the European Commission’s Joint Research Centre aimed at analyzing the future growth of aviation, the resulting fuel demand and the deployment of biofuels in the aviation sector in Europe. Three scenarios have been produced based on different input assumptions and leading to different underlying patterns of growth and resulting volumes of traffic. Data for aviation growth and hence fuel demand have been projected on a year by year basis up to 2030, using 2010 as the baseline. Data sources are Eurostat statistics and actual flight information from EUROCONTROL. Relevant variables such as the number of flights, the type of aircrafts, passengers or cargo tonnes and production indicators (RPKs) are used together with fuel consumption and CO₂ emissions data. The target of the European Advanced Biofuels Flightpath to ensure the commercialization and consumption of 2 million tons of sustainably produced paraffinic biofuels in the aviation sector by 2020, has also been taken into account. Results regarding CO₂ emission projections to 2030, reveal a steady annual increase in the order of 3%, 1% and 4% on average, for the three different scenarios, providing also a good correlation compared to the annual traffic growth rates that are indicated in the three corresponding scenarios. In absolute values, these ratios correspond to the central, the pessimistic and the optimistic scenarios respectively, corresponding to 360 million tonnes CO₂ emissions in 2030, ranging from 271 to 401 million tonnes for the pessimistic and optimistic scenarios, respectively. This article also reports on the supply potential of aviation biofuels (clustered in HEFA/HVOs and biojet) based on the production capacity of facilities around the world and provides an insight on the current and future trends in aviation based on the European and national policies, innovations and state-of-the art technologies that will influence the future of sustainable fuels in aviation.     

Reducing speed and fuel transfer of the Green Flag Incentive Program in Kaohsiung Port Taiwan

This research applied the Green Flag Program to assess the benefits of reducing speed and fuel transfer for large merchant vessels (bulk and container) entering Kaohsiung Port. This study adopts an activity-based model to calculate fuel consumption and emissions, as well as setting up two scenarios, (1) decrease vessel speed to 12 knots 20 nm away from port; and (2) decrease vessel speed to 12 knots and transfer fuel 20 nm away from port, which based on the Green Flag Program in Long Beach, in the U.S. The findings are (1) In scenario one, the container and bulk vessels saw reductions in CO₂ emissions of about 41% and 14%, respectively. In scenario two, container and bulk vessels had reductions of about 48% and 43% in SO₂ emissions, respectively. (2) Large vessels are more environmentally friendly than small vessels. (3) Using the CATCH model to assess the effectiveness of the two scenarios, it was found that container vessels benefited from both reducing speed and fuel transfer, while bulk carriers only did so from the former.     

Effects of battery chemistry and performance on the life cycle greenhouse gas intensity of electric mobility

Lithium traction batteries are a key enabling technology for plug-in electric vehicles (PEVs). Traction battery manufacture contributes to vehicle production emissions, and battery performance can have significant effects on life cycle greenhouse gas (GHG) emissions for PEVs. To assess emissions from PEVs, a life cycle perspective that accounts for vehicle production and operation is needed. However, the contribution of batteries to life cycle emissions hinge on a number of factors that are largely absent from previous analyses, notably the interaction of battery chemistry alternatives and the number of electric vehicle kilometers of travel (e-VKT) delivered by a battery. We compare life cycle GHG emissions from lithium-based traction batteries for vehicles using a probabilistic approach based on 24 hypothetical vehicles modeled on the current US market. We simulate life-cycle emissions for five commercial lithium chemistries. Examining these chemistries leads to estimates of emissions from battery production of 194–494 kg CO₂ equivalent (CO₂e) per kWh of battery capacity. Combined battery production and fuel cycle emissions intensity for plug-in hybrid electric vehicles is 226–386 g CO₂e/e-VKT, and for all-electric vehicles 148–254 g CO₂e/e-VKT. This compares to emissions for vehicle operation alone of 140–244 g CO₂e/e-VKT for grid-charged electric vehicles. Emissions estimates are highly dependent on the emissions intensity of the operating grid, but other upstream factors including material production emissions, and operating conditions including battery cycle life and climate, also affect life cycle GHG performance. Overall, we find battery production is 5–15% of vehicle operation GHG emissions on an e-VKT basis.     

Does the aviation Emission Trading System influence the financial evaluation of new airplanes? An assessment of present values and purchase options

In this paper we assess the impact of the CO₂ costs for short- and long-haul aircraft based on present values and on purchase options. We evaluate purchase options with a framework developed for real option analysis to estimate the value of flexibility under uncertain kerosene and CO₂ prices. We find an average influence of CO₂ costs on present values of €1.1 million for the short haul plane and €4.1 million for the long-haul plane over the typical lifetime of an airplane. For purchase options, we find a CO₂ influence of €0.43 million for the long-haul plane and a moderate impact for the short-haul plane. The results underline the importance of CO₂ and kerosene costs for long-haul aircraft.     

Eco-driver training within the City of Calgary’s municipal fleet: Monitoring the impact

This article highlights eco-driving as an available policy option to reduce climate altering GHG emissions. Recognizing the need to reduce the environmental impact of its fleet operations, the City of Calgary is a leader in developing programs and policies that aim to reduce GHG emissions and associated pollutants resulting from the use of fossil fuels. Among local action taken against climate change, the City sought to quantify CO₂ emissions reductions from their municipal fleet as a result of eco-driver training, with a specific focus on engine idling. Fifteen drivers from the Development & Building Approvals Business Unit had in-vehicle monitoring technology (CarChips®) installed into their vehicles as part of a three-phase research process. The results show that gasoline and hybrid vehicles decreased average idling between 4% and 10% per vehicle per day, leading to an average emissions decrease of 1.7 kg of CO₂ per vehicle per day.     

Influence of driving patterns on vehicle emissions: A case study for Latin American cities

On-board real-time emission experiments were conducted on 78 light-duty vehicles in Bogota. Direct emissions of carbon monoxide (CO), carbon dioxide (CO₂), nitrogen oxides (NO_x) and hydrocarbons (HC) were measured. The relationship between such emissions and vehicle specific power (VSP) was established. The experimental matrix included both gasoline-powered and retrofit dual fuel (gasoline–natural gas) vehicles. The results confirm that VSP is an appropriate metric to obtain correlations between driving patterns and air pollutant emissions. Ninety-five percent of the time vehicles in Bogota operate in a VSP between −15.2 and 17.7 kW ton⁻¹, and 50% of the time they operate between −2.9 and 1.2 kW ton⁻¹, representing low engine-load and near-idling conditions, respectively. When engines are subjected to higher loads, pollutant emissions increase significantly. This demonstrates the relevance of reviewing smog check programs and command-and-control measures in Latin America, which are widely based on static (i.e., idling) emissions testing. The effect of different driving patterns on the city’s emissions inventory was determined using VSP and numerical simulations. For example, improving vehicle flow and reducing sudden and frequent accelerations could curb annual emissions in Bogota by up to 12% for CO₂, 13% for CO and HC, and 24% for NO_x. This also represents possible fuel consumption savings of between 35 and 85 million gallons per year and total potential economic benefits of up to 1400 million dollars per year.     

Adapting the shipping sector to stricter emissions regulations: Fuel switching or installing a scrubber?

This paper examines how the existing fleet in the shipping industry can be adapted to the new emission regulations through the two main techniques that currently exist: (a) the use of low-sulphur marine diesels; and (b) the installation of scrubbers. A method is presented here for drawing up an economic assessment of both these techniques under uncertainty. It enables the best option to be selected at any given time taking into account fuel prices (spot and futures), scrubber installation costs, the time that the vessel operates in an Emission Control Area (ECA) and the remaining useful lifetime of the vessel. The paper also considers the possibility of an unexpected change from a non-ECA navigation area to an ECA. The assessment is carried out in a manner consistent with marine diesel and crude oil spot and futures market quotes. Our results show the net present value of investing in the installation of scrubbers and investing in changing fuel types for different assumptions on how vessels are operated. We also analyse increases in fuel consumption and CO₂ emissions as a consequence of using scrubbers and how they affects the financial analysis if such incremental emissions must be paid under a CO₂ pricing mechanism.     

Energy use and emissions of two stroke-powered tricycles in Metro Manila

CO, CO₂, NO_x and HC emissions of two stroke-powered tricycles in Metro Manila are examined using an instantaneous emissions model. Results show that fuel consumption and HC emissions in middle class residential areas and main roads are similar but lower than levels in low income residential areas. On the average, tricycles in Metro Manila consume 24.41 km/l of fuel and produces 9.5, 9.7, 40.5 and 0.07 g/km of HC, CO, CO₂ and NO_x, respectively. They fail to satisfy HC, CO and NO_x emission limits set by reference standards in the Philippines and other Asian countries. They produce greater HC and CO emissions than gasoline fueled private cars and diesel powered public jeepneys, taxis and buses on a per passenger-km basis but significantly lower NO_x emissions. Tricycles account for 15.4% of the total HC emissions from mobile sources in the metropolis while their contributions to CO, CO₂ and NO_x are minimal.     

Vehicle restrictions and CO2 emissions in Beijing – A simple projection using available data

The Beijing Government launched a new policy on restricting vehicle ownership in late 2010 to regulate the faster motorization and the excessive vehicular carbon dioxide (CO₂) emissions. In this paper, we first analyzed this policy and its effect on private passenger vehicle population. The private passenger vehicle population in Beijing from 2011 to 2020 was predicted under three different scenarios: no constraint (NC), current constraint (CC) and tighter constraint (TC). Then the assessment of vehicular emissions reduction benefits was made on the basis of private passenger vehicle population, vehicle kilometers traveled and CO₂ emission factors. It was projected that the CO₂ emissions in 2020 will reach 23.90, 15.55 and 13.23 million tons under NC, CC and TC respectively. The policy is very effective in controlling the faster motorization and reducing CO₂ emissions.     

How can shipowners comply with the 2020 global sulphur limit economically?

To comply with the International Maritime Organization’s (IMO) 2020 global sulphur limit for maritime shipping, low-sulphur fuel oils (LSFOs) and scrubbers are the most commonly applied approaches in practice, as a result of which, however, shipowners’ profits will be affected. This paper is to identify a more economical sulphur reduction approach, for which a 19,000 twenty-foot equivalent unit container ship sailing between Far East and Europe is set as a case study. Using the cost-benefit analysis, the use of scrubbers is proved to be more economical due to the higher net present value and lower annual unit cost. The sensitivity check suggests that a scrubber is more attractive in most cases except for two scenarios where LSFOs are more popular. That is, a scrubber is losing its attractiveness when prices of LSFOs and heavy fuel oil (HFO) move in the same direction with the price spread is equal to or below US$56 per ton, and when prices of HFO rise and prices of LSFOs fall with the price spread is equal to or below US$16 per ton. This finding well explains the current popularity of installing scrubbers among shipowners although retrofitting still faces many challenges.     

VISSIM/MOVES integration to investigate the effect of major key parameters on CO2 emissions

This paper looks at CO₂ emissions on limited access highways in a microscopic and stochastic environment using an optimal design approach. Estimating vehicle emissions based on second-by-second vehicle operation allows the integration of a microscopic traffic simulation model with the latest US Environmental Protection Agency’s mobile source emissions model to improve accuracy. A factorial experiment on a test bed prototype of the I-4 urban limited access highway corridor located in Orlando, Florida was conducted to identify the optimal settings for CO₂ emissions reduction and to develop a microscopic transportation emission prediction model. An exponentially decaying function towards a limiting value expressed in the freeway capacity is found to correlate with CO₂ emission rates. Moreover, speeds between 55 and 60 mph show emission rate reduction effect while maintaining up to 90% of the freeway’s capacity. The results show that speed has a significant impact on CO₂ emissions when detailed and microscopic analysis of vehicle operations of acceleration and deceleration are considered.     

Will technological progress be sufficient to stabilize CO2 emissions from air transport in the mid-term?

This article investigates whether anticipated technological progress can be expected to offset the CO₂ emissions resulting from rapid air traffic growth. Global aviation CO₂ emissions projections are examined for eight geographical zones until 2025. Air traffic flows are forecast using a dynamic panel-data econometric model, and then converted into corresponding quantities of air traffic CO₂ emissions using specific hypotheses and energy factors. None of our nine scenarios appears compatible with the objective of 450 ppm CO₂-eq. recommended by the Intergovernmental Panel on Climate Change. Nor is any compatible with the Panel’s aim of limiting global warming to 3.2 °C.     

Effect on direct injection naturally aspirated diesel engine characteristics fuelled by pine oil,ceiba pentandra methyl ester compared with diesel

This paper explores the experimental investigation of the performance, emission and combustion characteristics of bio fuels from ceiba pentandra methyl ester (CPME), ceiba pentandra methyl ester-pine oil blends (CPMEP) and pine oil and the results are compared with diesel. In ceiba pentandra seed oil the CPME yield is 92% by using transesterification process with the optimum conditions of 560 rpm, reaction time 58 min, catalyst concentration 13 g and methanol amount 500 ml. The viscosity of CPME is high when compare with diesel. So the low viscosity of pine oil is blended with CPME and it can be directly used in diesel engine without any modification. At different loads the Pine oil, CPME and CPMEP blends were used in direct injection naturally aspirated compression ignition engine. The outcomes exhibited that at full load conditions for CPME and CPMEP blends increased brake specific fuel consumption, and decreased brake thermal efficiency, CO, HC emissions. NOx emissions decreased and smoke emissions are increased on CPME and CPMEP blends, expect B25 blend compared with diesel. The combustion analysis like the heat release rate, peak cylinder pressure, cumulative heat release rate and ignition delay for CPME, CPMEP blends slightly lower and combustion duration higher than diesel and pine oil. At the Same engine operating condition, the engine fuelled with pine oil the values of brake thermal efficiency 4.79%, peak cylinder pressure, heat release rate, cumulative heat release rate and ignition delay are increased. Brake specific fuel consumption, CO, HC, and smoke were 9.46%, 16.66%, 14.89% and 8.33% decreased. However, the NOx emission is 8.29% higher than that of diesel. Experimental fuels up to B50 (50% pine oil and 50% CPME) blends have proved good potential for future energy is needed.     

Can rail/sail compete with air travel to Cyprus? A comparison of emissions

Rail and sea voyage journeys to Cyprus from a variety of origins are constructed to derive the travel emissions and travel time per person to compare popular aviation routes. The hypothetical ‘slow travel’ routes are approximately eight to ten times longer than flying. Emissions are lower from certain origins by about 100 kg CO₂ per person per round trip under reasonably high occupancy conditions when compared to current direct air services. Emissions from the sea voyages are derived from a sample of 162 marine vessels using the energy efficiency design index for European ships running at 20 knots.     

Carbon emission from urban passenger transportation in Beijing

Urban passenger transport significantly contributes to global greenhouse gas emissions, especially in developing countries owing to the rapid motorization, thus making it an important target for carbon reduction. This article established a method to estimate and analyze carbon emission from urban passenger transport including cars, rail transit, taxis and buses. The scope of research was defined based on car registration area, transport types and modes, the stages of rail transit energy consumption. The data availability and gathering were fully illustrated. A city level emission model for the aforementioned four modes of passenger transport was formulated, and parameters including emission factor of electricity and fuel efficiency were tailored according to local situations such as energy structure and field survey. The results reveal that the emission from Beijing’s urban passenger transport in 2012 stood at 15 million tonnes of CO₂, of which 75.5% was from cars, whereas car trip sharing constitutes only 42.5% of the total residential trips. Bus travel, yielding 28.6 g CO₂, is the most efficient mode of transport under the current situations in terms of per passenger kilometer (PKM) emission, whereas car or taxi trips emit more than 5 times that of bus trips. Although a decrease trend appears, Beijing still has potential for further carbon reduction in passenger transport field in contrast to other cities in developed countries. Development of rail transit and further limitation on cars could assist in reducing 4.39 million tonnes CO₂ emission.     

Valorization of carbon dioxide by conversion into fuel using renewable energy in Algeria

Reducing the emissions of the main anthropogenic greenhouse gases, such as carbon dioxide (CO₂), is one of the major challenges of this century. A partial solution to these environmental problems could be the capture and the conversion of carbon dioxide. The main objective of the present work is to study the opportunities and prospects of recycling carbon dioxide to produce synthetic fuel, particularly methanol, which is a complementary technology to carbon capture and storage (CCS). This methanol will be produced by using several renewable energies, such as solar, wind and geothermal, for the purpose of using it in the transportation sector in Algeria. In 2013, Algeria’s total amount of CO₂ emissions (created by energy consumption) was 143 million tonnes. It is estimated that 44.4 million tonnes of CO₂ can be captured from the exhaust of stationary units (factories and power stations) and converted to methanol every year. By adopting this process, approximately 32 million tonnes of methanol can be produced with an energy value of 580,000 TJ. The methanol produced from CO₂ can be used as an alternative transportation fuel. For this reason, the Geographical Information System (GIS) is used to present the spatial distribution of the methanol demand in short and long terms, based on market penetration rates, vehicle fleet and population data. An analysis of the energy balance, environment and economics of CO₂ recycling process is presented. In terms of environmental performance, the reduction in carbon dioxide emissions that come from the transport sector was remarkable in 2045.     

Analysis of fuel consumption and pollutant emissions of regulated and alternative driving cycles based on real-world measurements

Discrepancies between real-world use of vehicles and certification cycles are a known issue. This paper presents an analysis of vehicle fuel consumption and pollutant emissions of the European certification cycle (NEDC) and the proposed worldwide harmonized light vehicles test procedure (WLTP) Class 3 cycle using data collected on-road. Sixteen light duty vehicles equipped with different propulsion technologies (spark-ignition engine, compression-ignition engine, parallel hybrid and full hybrid) were monitored using a portable emission measurement system under real-world driving conditions. The on-road data obtained, combined with the Vehicle Specific Power (VSP) methodology, was used to recreate the dynamic conditions of the NEDC and WLTP Class 3 cycle. Individual vehicle certification values of fuel consumption, CO₂, HC and NO_x emissions were compared with test cycle estimates based on road measurements. The fuel consumption calculated from on-road data is, on average, 23.9% and 16.3% higher than certification values for the recreated NEDC and WLTP Class 3 cycle, respectively. Estimated HC emissions are lower in gasoline and hybrid vehicles than certification values. Diesel vehicles present higher estimated NO_x emissions compared to current certification values (322% and 326% higher for NO_x and 244% and 247% higher for HC + NO_x for NEDC and WLTP Class 3 cycle, respectively).     

An optimization model of energy and transportation systems: Assessing the high-speed rail impacts in the United States

This paper presents a long-term investment planning model that co-optimizes infrastructure investments and operations across transportation and electric infrastructure systems for meeting the energy and transportation needs in the United States. The developed passenger transportation model is integrated within the modeling framework of a National Long-term Energy and Transportation Planning (NETPLAN) software, and the model is applied to investigate the impact of high-speed rail (HSR) investments on interstate passenger transportation portfolio, fuel and electricity consumption, and 40-year cost and carbon dioxide (CO₂) emissions. The results show that there are feasible scenarios under which significant HSR penetration can be achieved, leading to reasonable decrease in national long-term CO₂ emissions and costs. At higher HSR penetration of approximately 30% relative to no HSR in the portfolio promises a 40-year cost savings of up to $0.63 T, gasoline and jet fuel consumption reduction of up to 34% for interstate passenger trips, CO₂ emissions reduction by about 0.8 billion short tons, and increased resilience against petroleum price shocks. Additionally, sensitivity studies with respect to light-duty vehicle mode share reveal that in order to realize such long-term cost and emission benefits, a change in the passenger mode choice is essential to ensure higher ridership for HSR.