The changing accuracy of traffic forecasts

Researchers have improved travel demand forecasting methods in recent decades but invested relatively little to understand their accuracy. A major barrier has been the lack of necessary data. We compiled the largest known database of traffic forecast accuracy, composed of forecast traffic, post-opening counts and project attributes for 1291 road projects in the United States and Europe. We compared measured versus forecast traffic and identified the factors associated with accuracy. We found measured traffic is on average 6% lower than forecast volumes, with a mean absolute deviation of 17% from the forecast. Higher volume roads, higher functional classes, shorter time spans, and the use of travel models all improved accuracy. Unemployment rates also affected accuracy—traffic would be 1% greater than forecast on average, rather than 6% lower, if we adjust for higher unemployment during the post-recession years (2008 to 2014). Forecast accuracy was not consistent over time: more recent forecasts were more accurate, and the mean deviation changed direction. Traffic on projects that opened from the 1980s through early 2000s was higher on average than forecast, while traffic on more recent projects was lower on average than forecast. This research provides insight into the degree of confidence that planners and policy makers can expect from traffic forecasts and suggests that we should view forecasts as a range of possible outcomes rather than a single expected outcome.

     

A traffic flow simulator for short‐term travel time forecasting

This paper presents an off‐line forecasting system for short‐term travel time forecasting. These forecasts are based on the historical traffic count data provided by detectors installed on Annual Traffic Census (ATC) stations in Hong Kong. A traffic flow simulator (TFS) is developed for short‐term travel time forecasting (in terms of offline forecasting), in which the variation of perceived travel time error and the fluctuations of origin‐destination (O‐D) demand are considered explicitly. On the basis of prior O‐D demand and partial updated detector data, the TFS can estimate the link travel times and flows for the whole network together with their variances and covariances. The short‐term travel time forecasting by O‐D pair can also be assessed and the O‐D matrix can be updated simultaneously. The application of the proposed off‐line forecasting system is illustrated by a numerical example in Hong Kong.     

The Effectiveness of Conceptual Airport Terminal Designs

Abstract

Aviation passenger traffic is forecast to grow significantly over the next decade and beyond. To accommodate this growth will require investment in airport infrastructure, including terminals. These buildings represent large, lumpy investments, so it is important to provide the capacity to accommodate the forecast traffic. However, this depends on at least two factors: the accuracy of the forecast of future demand, and the process of translating these forecasts into designs. Error in either factor can be potentially catastrophic financially. Translating forecasts into designs depends on ‘rules of thumb’ formulae that convert design hour flows into area requirements for each terminal facility. This paper examines the process of translating demand forecasts into conceptual terminal designs. The basic methods used are outlined, and how they affect the conceptual terminal design process are revealed. A model for conceptual terminal design is derived, presented and validated based on a sample of UK airports. It is shown that even if demand forecasts can be taken to be completely accurate, there can still be errors in terminal design and size resulting from the use of these ‘rules of thumb’.     

A demand trend change early warning forecast model for the city of São Paulo multi-airport system

The need of accurate forecasts of air passenger numbers to assist managerial decision making for both short and long terms is well recognized and a central problem on both short and long term forecasting is how to handle future trend. The aim of this paper is to develop a demand trend change early warning forecast model (EWFM) for the city of São Paulo multi-airport system (SPMARs). For SPMARs the EWFM is based on the combination of leading indicators and alarms against possible occurrence of changes on trend component of the monthly number of domestic air passengers. A topdown induction procedure is employed to identify leading indicators to provide an interpretable prediction procedure to support the development of scenarios for future demand trend. Results show that changes on such demand trend are mostly associated to changes on the economic activity and six different scenarios were built combining the identified leading indicators. The EWFM was employed to assist managerial decision making for both short and long terms in order to evaluate different alternatives to prevent congestion delay occurrences and to support infrastructure planning.     

Analysis of peak and non‐peak traffic forecasts using combined models

Accurate and timely traffic forecasting is crucial to effective management of intelligent transportation systems (ITS). To predict travel time index (TTI) data, we select six baseline individual predictors as basic combination components. Applying the one‐step‐ahead out‐of‐sample forecasts, the paper proposes several linear combined forecasting techniques. States of traffic situations are classified into peak and non‐peak periods. Based on detailed data analyses, some practical guidance and comments are given in what situation a combined model is better than an individual model or other types of combined models. Indicating which model is more appropriate in each state, persuasive comparisons demonstrate that the combined procedures can significantly reduce forecast error rates. It reveals that the approaches are practically promising in the field. To the best of our knowledge, it is the first time to systematically investigate these approaches in peak and non‐peak traffic forecasts. The studies can provide a reference for optimal forecasting model selection in each period. Copyright © 2010 John Wiley & Sons, Ltd.     

Public transport demand estimation by calibrating a trip distribution-mode choice (TDMC) model from passenger counts: A case study in Bandung,Indonesia

A problem always found in developing countries is the lack of information required for short, medium and long term planning purposes due to money and time constraints. This becomes even more valuable for problems which require ‘quick-response’ treatment. A flexible model approach allows monitoring a long term plan in order to check its short term performance at regular intervals using easily-available data. If found necessary, changes to the plan may be evaluated and eventually implemented. For this reason, the approach is deemed appropriate for long term planning and project evaluation even in the case of rapid changes in land-use, socio-economic and population parameters usually occurs in most of developing countries. A key element of the approach is a system to update the forecasting model (in particular its trip distribution and mode choice elements) using low-cost and/or easily-available information. Traffic counts are particularly attractive to be used in developing countries for planning purposes. The estimation of public transport demand, particularly important for planning purposes, is an expensive and time consuming undertaking. The need for a low-cost method to estimate the public transport demand is therefore obvious. The objective of this paper is the development of methods and techniques for modelling the public transport demand using traffic (passenger) count information and other simple zonal-planning data. We will report on a family of aggregate model combined with a family of mode choice logit models which can be calibrated from traffic (passenger) counts and other low-cost data. The model examined was the Gravity (GR) model combined with the Multi-Nominal-Logit (MNL) model. Non-Linear-Least-Squares (NLLS) estimation method was used to calibrate the parameter of the combined model. The combined TDMC model and the calibration method have been implemented into a micro-computer package capable of dealing with the study area consisting of up to 300 zones, 3000 links and 6000 nodes. The approach has been tested using the 1988 Public Transport Data Survey in Bandung (Indonesia). The model was found to provide a reasonably good fit and the calibrated parameter can then be used for forecasting purposes. General conclusion regarding the advantageous and the applicability of the approach to other environments are given.     

Travel demand forecasts improved by using cross-sectional data from multiple time points

Forecasts of travel demand are often based on data from the most recent time point, even when cross-sectional data is available from multiple time points. This is because forecasting models with similar contexts have higher transferability, and the context of the most recent time point is believed to be the most similar to the context of a future time point. In this paper, the author proposes a method for improving the forecasting performance of disaggregate travel demand models by utilising not only the most recent dataset but also an older dataset. The author assumes that the parameters are functions of time, which means that future parameter values can be forecast. These forecast parameters are then used for travel demand forecasting. This paper describes a case study of journeys to work mode choice analysis in Nagoya, Japan, using data collected in 1971, 1981, 1991, and 2001. Behaviours in 2001 are forecast using a model with only the most recent 1991 dataset and models that combine the 1971, 1981, and 1991 datasets. The models proposed by the author using data from three time points can provide better forecasts. This paper also discusses the functional forms for expressing parameter changes and questions the temporal transferability of not only alternative-specific constants but also level-of-service and socio-economic parameters.     

Short‐term travel time forecasts for transport information system in hong kong

In this paper, a case study is carried out in Hong Kong for demonstration of the Transport Information System (TIS) prototype. A traffic flow simulator (TFS) is presented to forecast the short‐term travel times that can be served as a predicted travel time database for the TIS in Hong Kong. In the TFS, a stochastic deviation coefficient is incorporated to simulate the minute‐by‐minute fluctuation of traffic flows within the peak hour period. The purposes of the case study are: 1) to show the applicability of the TFS for larger‐scale road network; and 2) to illustrate the short‐term forecasting of path travel times in practice. The results of the case study show that the TFS can be applied to real network effectively. The predicted travel times are compared with the observed travel times on the selected paths for an OD pair. The results show that the observed path travel times fall in the 90% confidence interval of the predicted path travel times.     

基于桥梁挠度长期监测值的动态预测

文章针对重庆高家花园嘉陵江大桥实时健康监测系统的挠度长期监测数据,根据监测信息的时间序列呈季节、循环等非平稳状态特点,介绍采用ARMA时间序列预测模型,对挠度监测数据中所包含的外荷载的变化趋势及结构抗力的衰变信息进行动态预测,同时建立了结构外效应的预测函数。结果表明,采用低阶模型能对挠度监测值进行较好的动态预测。     

Traffic forecasts under uncertainty and capacity constraints

Traffic forecasts provide essential input for the appraisal of transport investment projects. However, according to recent empirical evidence, long-term predictions are subject to high levels of uncertainty. This article quantifies uncertainty in traffic forecasts for the tolled motorway network in Spain. Uncertainty is quantified in the form of a confidence interval for the traffic forecast that includes both model uncertainty and input uncertainty. We apply a stochastic simulation process based on bootstrapping techniques. Furthermore, the article proposes a new methodology to account for capacity constraints in long-term traffic forecasts. Specifically, we suggest a dynamic model in which the speed of adjustment is related to the ratio between the actual traffic flow and the maximum capacity of the motorway. As an illustrative example, this methodology is applied to a specific public policy that consists of suppressing the toll on a certain motorway section before the concession expires.     

Predicting short-term bus passenger demand using a pattern hybrid approach

This paper proposes an Interactive Multiple Model-based Pattern Hybrid (IMMPH) approach to predict short-term passenger demand. The approach maximizes the effective information content by assembling the knowledge from pattern models using historical data and optimizing the interaction between them using real-time observations. It can dynamically estimate the priori pattern models combination in advance for the next time interval. The source demand data were collected by Smart Card system along one bus service route over one year. After correlation analysis, three temporal relevant pattern time series are generated, namely, the weekly, daily and hourly pattern time series. Then statistical pattern models are developed to capture different time series patterns. Finally, an amended IMM algorithm is applied to dynamically combine the pattern models estimations to output the final demand prediction. The proposed IMMPH model is validated by comparing with statistical methods and an artificial neural network based hybrid model. The results suggest that the IMMPH model provides a better forecast performance than its alternatives, including prediction accuracy, robustness, explanatory power and model complexity. The proposed approach can be potentially extended to other short-term time series forecast applications as well, such as traffic flow forecast.     

Forecasting light-duty vehicle demand using alternative-specific constants for endogeneity correction versus calibration

We investigate parameter recovery and forecast accuracy implications of incorporating alternative-specific constants (ASCs) in the utility functions of vehicle choice models. We compare two methods of incorporating ASCs: (1) a maximum likelihood estimator that computes ASCs post-hoc as calibration constants (MLE-C) and (2) a generalized method of moments estimator that uses instrumental variables (GMM-IV) to correct for price endogeneity. In a synthetic study we observe significant coefficient bias with MLE-C when the price-ASC correlation (endogeneity) is large. GMM-IV successfully mitigates this bias given valid instruments but exacerbates the bias given invalid instruments. Despite greater coefficient bias, MLE-C yields better forecasts than GMM-IV with valid instruments in most of the cases examined, including most cases where the price-ASC correlation present in the estimation data is absent in the prediction data. In a market study of U.S. midsize sedan sales from 2002 – 2006 the GMM-IV model predicts the 1-year-forward market better, but the MLE-C model predicts the 5-year-forward market better. Including an ASC in predictions by any of the methods proposed improves share forecasts, and assuming that the ASC of each new vehicle matches that of its closest competitor vehicle yields the best long term forecasts. We find evidence that the instruments most frequently used in the automotive demand literature may be invalid.     

Predicting travel time reliability using mobile phone GPS data

Estimates of road speeds have become commonplace and central to route planning, but few systems in production provide information about the reliability of the prediction. Probabilistic forecasts of travel time capture reliability and can be used for risk-averse routing, for reporting travel time reliability to a user, or as a component of fleet vehicle decision-support systems. Many of these uses (such as those for mapping services like Bing or Google Maps) require predictions for routes in the road network, at arbitrary times; the highest-volume source of data for this purpose is GPS data from mobile phones. We introduce a method (TRIP) to predict the probability distribution of travel time on an arbitrary route in a road network at an arbitrary time, using GPS data from mobile phones or other probe vehicles. TRIP captures weekly cycles in congestion levels, gives informed predictions for parts of the road network with little data, and is computationally efficient, even for very large road networks and datasets. We apply TRIP to predict travel time on the road network of the Seattle metropolitan region, based on large volumes of GPS data from Windows phones. TRIP provides improved interval predictions (forecast ranges for travel time) relative to Microsoft’s engine for travel time prediction as used in Bing Maps. It also provides deterministic predictions that are as accurate as Bing Maps predictions, despite using fewer explanatory variables, and differing from the observed travel times by only 10.1% on average over 35,190 test trips. To our knowledge TRIP is the first method to provide accurate predictions of travel time reliability for complete, large-scale road networks.     

The role of volume-delay functions in forecasting and evaluating congestion charging schemes: the Stockholm case

This paper uses observations from before and during the Stockkholm congestion charging trial in order to validate and improve a transportation model for Stockholm. The model overestimates the impact of the charges on traffic volumes while at the same time it substantially underestimates the impact on travel times. These forecast errors lead to considerable underestimation of economic benefits which are dominated by travel time savings. The source of error lies in the static assignment that is used in the model. Making the volume-delay functions (VDFs) steeper only marginally improves the quality of forecast but strongly impacts the result of benefit calculations. We therefore conclude that the dynamic assignment is crucial for an informed decision on introducing measures aimed at relieving congestion. However, in the absence of such a calibrated dynamic model for a city, we recommend that at least a sensitivity analysis with respect to the slope of VDFs is performed.     

Forecasting demand for high speed rail

It is sometimes argued that standard state-of-practice logit-based models cannot forecast the demand for substantially reduced travel times, for instance due to High Speed Rail (HSR). The present paper investigates this issue by reviewing the literature on travel time elasticities for long distance rail travel and comparing these with elasticities observed when new HSR lines have opened. This paper also validates the Swedish long distance model, Sampers, and its forecast demand for a proposed new HSR, using aggregate data revealing how the air–rail modal split varies with the difference in generalized travel time between rail and air. The Sampers long distance model is also compared to a newly developed model applying Box–Cox transformations. The paper contributes to the empirical literature on long distance travel, long distance elasticities and HSR passenger demand forecasts. Results indicate that the Sampers model is indeed able to predict the demand for HSR reasonably well. The new non-linear model has even better model fit and also slightly higher elasticities.     

Interactive travel choices and traffic forecast in a doubly dynamical system with user inertia and information provision

This study models the joint evolution (over calendar time) of travelers’ departure time and mode choices, and the resulting traffic dynamics in a bi-modal transportation system. Specifically, we consider that, when adjusting their departure time and mode choices, travelers can learn from their past travel experiences as well as the traffic forecasts offered by the smart transport information provider/agency. At the same time, the transport agency can learn from historical data in updating traffic forecast from day to day. In other words, this study explicitly models and analyzes the dynamic interactions between transport users and traffic information provider. Besides, the impact of user inertia is taken into account in modeling the traffic dynamics. When exploring the convergence of the proposed model to the dynamic bi-modal commuting equilibrium, we find that appropriate traffic forecast can help the system converge to the user equilibrium. It is also found that user inertia might slow down the convergence speed of the day-to-day evolution model. Extensive sensitivity analysis is conducted to account for the impacts of inaccurate parameters adopted by the transport agency.     

Forecasting bunker prices; A nonstationary,multivariate methodology

This paper suggests a methodological approach for the forecasting of marine fuel prices. The prediction of the bunker prices is of outmost importance for operators, as bunker prices affect heavily the economic planning and financial viability of ventures and determine decisions related to compliance with regulations. A multivariate nonstationary stochastic model available in the literature is being retrieved, after appropriate adjustment and testing. The model belongs to the class of periodically correlated stochastic processes with annual periodic components. The time series are appropriately transformed to become Gaussian, and then are decomposed to deterministic seasonal characteristics (mean value and standard deviation) and a residual time series. The residual part is proved to be stationary and then is modeled as a Vector AutoRegressive Mooving Average (VARMA) process. Finally, using the methodology presented, forecasts of a tetra-variate and an octa-variate time series of bunker prices are produced and are in good agreement with actual values. The obtained results encourages further research and deeper investigation of the driving characters of the multivariate time series of bunker prices.     

Short-term,real-time prediction of the extreme ambient carbon monoxide concentrations due to vehicular exhaust emissions using transfer function-noise model

The Box–Jenkins transfer function-noise (TFN) models (Box, G.E.P., Jenkins, G.M., Reinsel, G.C., 1994. Time Series Analysis: Forecasting and Control, 3rd ed. Prentice-Hall, Englewood Cliffs, NJ.) have been used to provide short-term, real-time forecast of the extreme carbon monoxide for an air quality control region (AQCR) comprising a major traffic intersection in the centre of the capital city of Delhi. The time series of the surface wind speed and ambient temperature have been used as “explaining” exogenous variables in the TFN models. When compared with the results of univariate ARIMA model of the endogenous series, the forecast performance is found to improve with the inclusion of the wind speed as input series; however, no significant improvement is observed in the forecast with the inclusion of temperature as input series.     

Short‐term traffic forecasting: Overview of objectives and methods

In the last two decades, the growing need for short‐term prediction of traffic parameters embedded in a real‐time intelligent transportation systems environment has led to the development of a vast number of forecasting algorithms. Despite this, there is still not a clear view about the various requirements involved in modelling. This field of research was examined by disaggregating the process of developing short‐term traffic forecasting algorithms into three essential clusters: the determination of the scope, the conceptual process of specifying the output and the process of modelling, which includes several decisions concerning the selection of the proper methodological approach, the type of input and output data used, and the quality of the data. A critical discussion clarifies several interactions between the above and results in a logical flow that can be used as a framework for developing short‐term traffic forecasting models.     

Simplifications for single-route transit-ridership forecasting models

The growth in popularity of microcomputers has reemphasized the need for simplified transit-planning techniques. This paper describes and evaluates a single-route ridership forecasting model which is designed to fit within a modest-sized microcomputer. The model is based upon the traditional four-step urban transportation modeling process, but it is simplified by removing the possibility of multiple transfers and by eliminating the highway network. An analysis of model error shows that these simplifications do not appreciably affect the accuracy of the forecasts. A particular advantage of implementing the model on a microcomputer is the user-friendliness that can be achieved by employing interactive color graphics for data input.