共查询到17条相似文献,搜索用时 843 毫秒
1.
2.
3.
气动力噪声控制技术
控制气动力噪声主要是控制进、排气系统的噪声,而控制进、排气噪声的途径和采用的办法是相同的,在保证发动机输出功率不降低的情况下.可通过改进发动机配气机构或在排气机构安装消声器的方法降低进、排气噪声。目前广泛采用的纸质空气滤清器和排气消声器能明显有效地降低进、排气噪声。 相似文献
4.
5.
本文在对■7种消声器做了静态声学性能试验、发动机台架试验及整车车外噪声试验的基础上,对降低重型汽车车外噪声的措施以及重型汽车排气消声器的类型、特点、设计、试验进行了探讨,并得出以下结论: (1) 改进消声器,提高消声性能,是一种比较经济而有效的措施; (2) 重型汽车排气消声器以阻抗复合式为好; (3) 选择和设计消声器时要考虑发动机排气噪声的特点; (4) 车辆在停车状态下的车外最大噪声值是一个很有用的参数。最后,对CQ261型汽车排气消声器提出了改进意见。 相似文献
6.
7.
8.
为了降低发动机排气系统噪声,首先利用计算流体力学方法,对汽车发动机排气系统模型的内部流场进行三维数值模拟;其次通过计算得到计算域内流场分布,观察打开不同排气歧管入口时消音器及尾管的内部流线图、催化转化器内部气体流动均匀性来研究分析发动机排气歧管噪声的产生原因。最后根据分析结果找出原结构中不合理的部位,并提出2种对发动机排气系统的优化改进方案,以达到减小排气阻力和排气噪声的目的。 相似文献
9.
10.
针对某乘用车消声器在发动机转速1 500~3 000 r/min范围内尾管噪声偏大的问题,应用GT-Power软件建立发动机及排气系统模型,并对该模型进行了试验验证。应用DoE方法找到了对消声器性能影响较大的参数,建立了消声器性能综合评价体系。依据运行工况及指标的重要程度为各转速下的评价指标设计了相应的权重,通过多目标优化计算得到了最优化的消声器结构参数。优化后消声器的模拟计算结果表明,在发动机转速1 500~3 000 r/min范围内,尾管总噪声和2阶噪声有较大程度上的降低。 相似文献
11.
在机动车辆的行驶中,发动机的排气噪音和排放污染是非常高的,为降低噪音和减少排放污染,在机动车辆上都设置有消声装置。但目前常见的各种原理的消声器效果都不太理想,而且经过消声处理的气体中还含有大量的粒状物、絮状物、油水混合物以及一氧化碳等有害物质,这些物质直接危害着生态环境。本文目的是提供一种新型的消声器设计方案,从而提高现有消声器性能,降低其噪音污染并减少排放的有害物质量。 相似文献
12.
13.
排气噪声是汽车的主要噪声源之一,往往比内燃机本体噪声高出10~15dB。使用合适的消声器是控制和降低排气噪声的有效手段,因而对排气消声器的研究越来越成为汽车排气噪声控制的热点。文章从实用性角度和声学原理出发,分析了一种普适性消声器结构及其降噪机理,并通过实验进行了有效验证。 相似文献
14.
15.
If a vehicle that meets emission regulations operates sufficiently for a long time under low speed and low load conditions,
soot contained in the exhaust gas is accumulated on the inner surface of the exhaust system. This soot deposition problem
occurs frequently in all diesel cars. However, when a vehicle is placed under the conditions of sudden start and sudden acceleration
after city mode driving for a long time, the deposited soot is abruptly blown up with the soot produced during fuel combustion.
In the present study, the main cause of the abrupt outburst of deposited soot is investigated to overcome this adverse phenomenon.
First, we developed a method to quantify the amount of the exhausted soot particles (or the accumulated soot particles) by
measuring the opacity that represents the contamination level of the exhaust gas due to soot particles. Using this measuring
scheme for deposited soot, we found the critical conditions for engine speeds and load conditions at which soot particles
are emitted into the air without accumulation in the exhaust system using main muffler composed of three chambers. In order
to meet these critical conditions and thus to drastically reduce soot accumulation, the exhaust system using the main muffler
applied in this study must be designed to ensure that the flow velocity of the exhaust gas is higher than 62 m/s when the
back pressure at the exit of the turbocharger is under 0.08 bars. 相似文献
16.
17.
为分析消声器压力场和温度场对其内部结构强度及排气效果的影响,在给定边界条件下,采用Fluent软件对某消声器进行内流场模拟计算。分析结果表明,消声器内压力温度场分布较均匀,但在过渡位置容易出现压力温度突变。指出消声器各腔长度影响其频谱移动,消声器过渡结构应平缓以减少压力损失,否则造成消声器热力变形。 相似文献