板架弯曲二次应力对纵骨疲劳评估影响的研究

为了验证散货船、油船协调共同规范(HCSR)中在计算纵骨疲劳寿命时不考虑板架弯曲纵骨二次应力的合理性,讨论两种二次应力的计算方法,分别对散货船和油船板架的纵骨的二次应力进行计算,通过对是否考虑纵骨二次应力计算得到的疲劳寿命进行对比,验证HCSR中简化算法计算纵骨疲劳寿命的合理性。     

超大型集装箱船纵骨贯穿孔的形状优化

基于在外板纵骨与横向肋板连接处的贯穿孔是疲劳裂纹的多发地带,以某超大型集装箱船为例,介绍了船体外板纵骨贯穿孔的受力状态,并基于谱分析方法,对该型船舭部外板纵骨贯穿孔结构进行了疲劳强度分析。通过比较不同结构形式贯穿孔的疲劳寿命和不同结构形式纵骨贯穿孔的优缺点,总结并提出了超大型集装箱船纵骨贯穿孔结构形式的设计要点。     

基于断裂力学的散货船外底纵骨疲劳寿命评估

基于断裂力学的疲劳裂纹扩展理论,按《散货船共同结构规范》确定疲劳载荷及计算工况,通过有限元应力分析对某散货船外底纵骨与横舱壁或横框架连接节点处进行疲劳寿命分析,并探讨了裂纹形状比对疲劳寿命的影响。研究结果表明,外底纵骨上远离横舱壁或横框架一侧的软趾端处的疲劳寿命比靠近横舱壁或横框架一侧的通焊孔焊缝趾端处的疲劳寿命要短,并且疲劳寿命随着裂纹形状比的增大而增大。     

LNG船纵骨端部表面裂纹疲劳扩展寿命计算

基于断裂力学的裂纹扩展方法预报液舱纵骨端部的疲劳寿命。采用有限元软件对液舱纵骨端部节点处表面裂纹应力强度因子进行系列计算,并在BS7910经验公式的基础上拟合出趾端的应力强度因子修正系数经验公式。将采用该公式得到的结果与有限元计算结果相对比,结果表明二者能较好地吻合,该公式可应用到类似端部结构裂纹扩展应力强度因子的计算中。按挪威船级社(Det Norske Veritas,DNV)规范的要求组合热点主应力幅值,并按降序对各载荷块构造液舱疲劳热点载荷谱,结合修正公式系数经验计算液舱纵骨端部趾端的裂纹扩展寿命,预报的疲劳寿命满足要求。     

原油转驳船结构疲劳强度分析研究

基于谱分析方法对于CTV模型的易疲劳区域进行筛选,对于筛选出的舷侧纵骨切口疲劳热点区域,考虑水线附近的水压力动态折减因素进行单独校核。参考校核结果,优化纵骨切口角隅疲劳热点区域的补板结构形式,使应力平稳过渡,使疲劳寿命满足设计需求。     

超大型浮体柔性连接器疲劳强度模型试验

为了保证超大型浮体的作业安全,需要精确评估连接器结构疲劳强度。文章针对一种由尼龙柔性夹层和环肋加强圆管轴构成的铰接式连接器,开展了疲劳强度模型试验,测量了热点应力、疲劳寿命和裂纹扩展。考虑接触、柔性层以及开孔的影响,采用三维有限元方法计算了连接器结构应力,分别基于S-N曲线和裂纹扩展,给出了柔性连接器疲劳寿命评估方法。比较分析表明,计算得到的连接器结构应力和疲劳寿命与模型试验结果吻合,文中方法可用于柔性连接器结构疲劳强度设计     

双轴加载下船底纵骨疲劳寿命试验与数值模拟研究

以实尺度制作了疲劳试验的试件,对45000DWT江海直达散货船船底纵骨与水密及非水密实肋板连接处进行了双轴恒幅循环载荷下的疲劳试验,记录了热点处的疲劳裂纹扩展长度和对应循环次数,获得船底纵骨疲劳特性;根据不同节点处裂纹萌生和扩展情况,得出非水密节点处是疲劳危险处;用动态应变仪记录热点处的应变,根据新版《船体结构疲劳强度指南》中的热点应力法计算热点应力,用试验数据拟合了一条S-N曲线,与指南提供的D曲线进行了对比分析,验证了D曲线的合理性。同时用MSC.Patran软件建立有限元模型,选取2007版《船体结构疲劳强度指南》中名义应力法对应结构形式的F曲线,用MSC.fatigue模块计算了相应节点的总疲劳寿命,将有限元结果和试验结果进行对比,验证了热点应力法的准确性。     

FPSO纵骨疲劳寿命分析

FPSO(Floating Production Storage and Offloading)长期系泊于定位海域,在服役期内没有进坞维修的可能。而在这个过程中,其船体结构承受不间断的交替变化的载荷,再加上高强度钢的广泛使用,使其疲劳破坏问题更加突出,因此其疲劳设计更为严格。本文以一大型浮式生产储油船为例,选取了典型剖面,采用简化的计算法进行纵骨的疲劳分析,给出了纵骨疲劳寿命计算的基本过程并且对船体结构中几种常见的节点连接方式的纵骨进行了疲劳寿命计算,通过分析比较,发现肘板软趾对疲劳寿命影响很大,从而找出最佳的端部节点连接形式,为工程设计提供依据。     

船舶典型结构焊接残余应力的有限元分析

在船舶建造中,会有大量的纵骨对接焊缝,存在复杂的焊接残余应力,对结构的极限强度及疲劳寿命有一定影响。该文运用有限元软件ANSYS的APDL语言编写出相应的计算程序,对平板对接焊进行数值模拟,并与试验值进行对比分析。在此基础上,对船舶典型纵骨对接焊进行数值模拟分析,得到相应的残余应力的分布规律。     

超大型油船波激振动研究

本文论述了超大型船发生波激振动的机理及其实船测量和船模试验以及理论预报方法，还探讨了波激振动对超大型油船总纵强度及疲劳寿命的影响。     

Errata

正In the paper"Influence of Fouling Assemblage on the Corrosion Behaviour of Mild Steel in the Coastal Waters of The Gulf of Mannar,India"in Vol.12,No.4,Page:509,References were lost,and the two authors’biographies were identical.The correct text is shown below.We apologize to the authors and our readers for any inconvenience caused by the errors.     

Journal of Marine Science and Application 2014 Sum. Contents

正~~     

第34届海洋、离岸及极地工程国际会议(英文)

正St.John's,Newfoundland,Canada,May 31-June 5,2015 OMAE2015 is the ideal forum for researchers,engineers,managers,technicians and students from the scientific and industrial communities from around the world to: meet and present advances in technology and its scientific support;     

联合作战计划和执行系统

全球指挥控制系统(GCCS)实施当前美国海军网络中心战信息基础设施的联合计划网络。联合作战计划和执行系统(JOPES)支持GCCS实现联合计划。JOPES有两类计划：时间不限的精密预案计划生成作战计划、方案计划或职能计划；时间敏感的危机行动计划生成作战命令或战役方案。前者在和平时期创建的作战计划是后者的计划基础，加速应付危机的能力。     

Eastbound or westbound ?

In terms of equal sailing distances, where is the inflexion when ships depart from ports in the Asian Continent to New York via Suez and/or Panama？
The answer is China South Port Group （Hong Kong, Shenzhen and Guangzhou）.     

Recent progress on wave induced loading measurements in warships

Recent measurements of wave induced hull strain and flexure in RN warships are presented together with the derivation of the current design criteria for extreme hull girder bending loads. The history of the development of the shipboard instrumentation used is given and recent developments to improve the quality and ease of analysis of the data are described. An unexpectedly high transverse asymmetry in the longitudinal strains measured in destroyers is shown to be the result of a combination of vertical and lateral bending in oblique seas. Finally recent theoretical comparisons between the loading of Deep-Vee hulls and conventional UK rounded bilge hulls are presented which demonstrate the higher loading experienced by this type of hull form.     

桥梁防撞设施物理模型试验

物理模型试验是预报防撞设施所受撞击力及优化设计方案的主要方法之一。结合杭州湾大桥柔性防撞设施及东海大桥独立式防撞体设计方案,阐述了船—防撞体撞击试验的基本原理、方法、试验方案及相关试验结果。提出了柔性防撞系统的优化方案。试验结果表明,该方案经济有效,可供预报类似桥梁防撞设施撞击力时参考。     

印尼某电厂码头水工建筑物设计

印尼某电厂项目码头水工建筑物包括码头、防波堤和护岸等主要组成部分。在该项目水工建筑物的设计过程中,综合考虑当地的自然条件、施工能力和材料来源等因素,不断优化结构选型和结构断面。根据不同使用要求,护岸分别采用直立式和斜坡式2种结构型式,推荐的设计方案节省投资、施工方便,可供同类工程设计参考。     

Impact of regulation on the performances of long-distance transport services: A comparison of the different approaches in Sweden and Norway

Despite the many socio-economic similarities between Sweden and Norway, differences in jurisdiction, organisation, cooperation, and financing of long-distance passenger train and coach services have led to the development of four distinctively different ways of serving the markets. This paper describes how the train and coach markets have developed in the two countries, with emphasis on regulatory and industrial structure and a couple of performance variables.Looking at passenger rail, both countries separated infrastructure from operation over a decade ago. However, while Norwegian rail is characterised by an almost monopoly supplier, rail services in Sweden are partly decentralised to the responsibility of county authorities and are widely subjected to competitive tendering. The rest of the network is about to be opened up for on-the-track competition. Swedish Rail (SJ) has spent the last decades consolidating its core business (passenger rail) and sold out its other businesses. In contrast, the Norwegian state rail (NSB) has expanded its business to become a major bus operator and property owner, with extensions also into the Swedish market.The coach industry was more recently deregulated in both countries. The Swedish coach market is dominated by privately owned companies operating services to and from Stockholm. In Norway, state-owned NSB is a major coach operator on medium distance routes, and is also the largest partner of Nor-Way Bussekspress which totally dominates long-distance coach services. Further, the Norwegian coach market is characterised by cross-ownership and cooperation which has enabled an extensive route network which covers most of Norway.We find distinct differences in achievements in the two modes and in the two countries. Swedish rail services have succeeded in winning market shares and in renewing and developing both infrastructure and service levels to a greater extent than the Norwegian model. On the other hand, the Norwegian coach market seems to be more developed and efficient compared to its Swedish counterpart.The paper concludes with a discussion on the possible links between the different approaches and the performance observed, with the aim to stimulate further and more detailed research on some important issues.     

开放式数据挖掘系统模型

目前国内已经出现了少量的数据挖掘相关产品。国内数据挖掘软件无论从数量还是质量上比较，都与国外软件存在着较大的差距。随着数据仓库技术的普及，数据挖掘应用的需求越来越强烈，如何缩短这种差距，研发数据挖掘软件产品成为国内业界的一个重要问题。通过引用目前国际通用数据挖掘标准技术来构建开放式的数据挖掘系统模型，该系统模型从可扩展性、可重用性、易用性等方面得到了加强。