Coupler rotation behaviour and its effect on heavy haul trains

When a locomotive coupler rotates at an angle, the lateral component of the coupler force has an adverse effect on the locomotive's safety, particularly in heavy haul trains. In this paper, a model of a head-mid configuration, a 20,000-t heavy haul train is developed to analyse the rotation behaviour of the locomotive's coupler system and its effect on the dynamic behaviour of such a train's middle locomotive when operating on tangent and curved tracks. The train model includes detailed coupler and draft gear with which to consider the hysteretic characteristics of the rubber draft gear model, the friction characteristics of the coupler knuckles, and the alignment-control characteristics of the coupler shoulder. The results indicate that the coupler's rotation behaviour differs between the tangent and curved tracks, significantly affecting the locomotive's running performance under the braking condition. A larger coupler rotation angle generates a larger lateral component, which increases the wheelset's lateral force and the derailment coefficient. Decreasing the maximum coupler free angle can improve the locomotive's operational performance and safety. Based on these results, the recommended maximum coupler free angle is 4°.     

Simulation analysis on the coupler behaviour and its influence on the braking safety of locomotive

In order to simulate the runtime behaviour of coupler and buffer systems accurately, the dynamic model was improved by adopting the polygonal contact model. And the reliability of the friction phenomenon in flat-pin coupler’s tail and the connecting constraint between coupler heads were verified. Then the detailed model which fully considered the dynamic characteristics of middle locomotive and its adjacent wagons was incorporated into the simplified longitudinal dynamic model of combined heavy-haul train. The dynamic response of coupler and its influence on the running safety of locomotive under flat straight line emergency braking condition and long steep grade cycle braking condition were simulated respectively. According to the simulation results, the following suggestions were proposed: flat-pin coupler is more suitable for heavy-haul locomotive, but the inspection work on the friction surface of coupler tail needs to be strengthened; and the vertical anti-off stopping device should be added to avoid the occurrence of decoupling accidents.     

Analysis of the car body stability performance after coupler jack-knifing during braking

This paper aims to improve car body stability performance by optimising locomotive parameters when coupler jack-knifing occurs during braking. In order to prevent car body instability behaviour caused by coupler jack-knifing, a multi-locomotive simulation model and a series of field braking tests are developed to analyse the influence of the secondary suspension and the secondary lateral stopper on the car body stability performance during braking. According to simulation and test results, increasing secondary lateral stiffness contributes to limit car body yaw angle during braking. However, it seriously affects the dynamic performance of the locomotive. For the secondary lateral stopper, its lateral stiffness and free clearance have a significant influence on improving the car body stability capacity, and have less effect on the dynamic performance of the locomotive. An optimised measure was proposed and adopted on the test locomotive. For the optimised locomotive, the lateral stiffness of secondary lateral stopper is increased to 7875?kN/m, while its free clearance is decreased to 10?mm. The optimised locomotive has excellent dynamic and safety performance. Comparing with the original locomotive, the maximum car body yaw angle and coupler rotation angle of the optimised locomotive were reduced by 59.25% and 53.19%, respectively, according to the practical application. The maximum derailment coefficient was 0.32, and the maximum wheelset lateral force was 39.5?kN. Hence, reasonable parameters of secondary lateral stopper can improve the car body stability capacity and the running safety of the heavy haul locomotive.     

The stability mechanism and its application to heavy-haul couplers with arc surface contact

To investigate the stability mechanism of a type of heavy-haul coupler with arc surface contact, the force states of coupler were analysed at different yaw angles according to the friction circle theory and the structural characteristics of this coupler were summarised. A multi-body dynamics model with four heavy-haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability was tested in order to investigate the effect of relevant parameters on the coupler stability. The results show that this coupler exhibits the self-stabilisation and less lateral force at a small yaw angle. The yaw angle of force line is less than the actual coupler yaw angle which reduces the lateral force and the critical instability. An increase in the friction coefficient of the arc contact surfaces can improve the stability of couplers. The friction coefficient needs to be increased with the increase in the maximum coupler longitudinal compressive force. The stability of couplers is significantly enhanced by increasing the secondary suspension stiffness and reducing the clearance of the lateral stopper of the locomotives. When the maximum coupler compressive force reaches 2500 kN, the required friction coefficient reduces from 0.6 to 0.35, which notably lowers the derailment risk caused by the coupler. The critical instability angle of the coupler mainly depends on the arc contact friction coefficient. When the friction coefficient is 0.3, the critical instability angle was 4–4.5°. The simulation results are consistent with the locomotive line tests. These studies establish meaningful improvements for the stability of couplers and match the heavy-haul locomotive with its suspension parameters.     

The stability and mechanical characteristics of heavy haul couplers with restoring bumpstop

To investigate the stability and mechanical characteristics of a type of heavy haul coupler with restoring bumpstop, the geometry and force states of couplers were analysed at different yaw angles and the longitudinal forces. The structural characteristics of this coupler were summarised. To aid in the investigation, a multi-body dynamics model with four heavy haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability and lateral forces were tested in order to investigate the effect of relevant parameters on the locomotive's wheelset lateral forces. The results show that only when the bumpstop force exceeds half of the coupler longitudinal compression force, can the follower be rotated and the yaw angle of the coupler increase. The bumpstop preload is the most important stabilising factor. The coupler lateral force is constant when the coupler longitudinal force is smaller than the critical values of 2000, 1400 and 1150 kN at coupler free angles of 7°, 8° and 9°, respectively, for operation on straight track. The coupler free angle and the locomotive's lateral clearance of the secondary stopper are important in decreasing the wheelset lateral forces of the locomotive. It is advised that a smaller locomotive's secondary lateral suspension stiffness, a free clearance of 35 mm and an elastic clearance of 15 mm from the secondary lateral stopper be selected. If the coupler's free angle is less than the self-stabilising angle which is 5.5° for operation on straight track, the coupler is stable no matter how great the longitudinal force is. The wheelset lateral forces are allowed at the coupler longitudinal force of 2500 kN when the free angle is 6°. These studies establish meaningful improvements for the stability of couplers and match the heavy haul locomotive with its suspension parameters.     

On the overriding issue of train front end collision in rail vehicle dynamics

A three-dimensional dynamic model of crashed vehicles coupled with moving tracks is developed to research the dynamic behaviour of the train front end collision on tangent tracks. The three-dimensional dynamic model consists of a crashed vehicle model, moving track models, a simple wheel–rail contact model, a velocity-based coupler model and the model of energy absorption and anti-climbing devices. The vector method dealing with the nonlinear wheel–rail geometry is put forward in the paper. The developed model is applicable in the scope that central collisions occur on tangent tracks at low speeds. The examples of the vehicle impacting with a rigid wall and the train front end collision are carried out to obtain the dynamic responses of vehicles. The overriding issue is studied on the basis of the wheel rise in train collisions. The results show that the second bogie of the first colliding vehicle possesses the maximal wheel rise. The wheel rise increases with the increase of vehicles. However, the number of vehicles has tiny influence on the overriding in train collisions at low speeds. On the contrary, the impact speed has significant influence on the overriding in train collisions. The wheel rise increases rapidly if the impact speed is close to the critical speed of overriding. The large wheel rise is principally generated by the great coupler force related to the rigid impact in the axial direction.     

Coupler dynamic performance analysis of heavy haul locomotives

In this paper, a train dynamic model was developed to study the dynamic performance of heavy haul locomotives, taking into account the use of different coupler and buffer systems under conditions of severe longitudinal coupler compressive forces. The model consists of four locomotives each having 38 independent degrees of freedom and one dummy freight vehicle connected to each other by couplers and buffers. Simulation results showed that the longitudinal coupler compressive forces withstood by large rotation angle couplers with coupler shoulders were larger than those withstood by small rotation angle couplers. The results obtained for the large rotation angle coupler model showed that it had higher safety curve negotiation speeds. Due to the smaller static impedance, it was found that large capacity elastic clay (or cement) buffers cannot satisfy the requirement of heavy haul locomotives during cycle braking in long heavy downgraded tracks; the use of friction clay buffers can solve this problem.     

The mechanism for the coupler and draft gear and its influence on safety during a train collision

A mechanical model of the coupler and draft gear was established to study the mechanism during an intercity train collision. The model includes four rigid bodies, one spherical joint, two nonlinear torsion spring units and two nonlinear hysteresis units. Simulation and test results show that the axial characteristics of the model are reasonable and the model can reasonably simulate the pitching movement of the coupler. The influence of the coupler and draft gear on the collision behaviour of the train is analysed considering a four-section intercity train. The results show that during the collision process, the amount of compression of the middle coupler is an important factor influencing the pitching deflection angle. The pitching motion posture of the coupler changes with the initial pitching deflection angle, but the initial pitching deflection angle has little effect on its yawing deflection angle. When the pitching angle of the middle coupler is elevated, as the elevation angle increases, the derailment risk of the ‘A’ end bogie of the previous vehicle increases, whereas the risk of derailment of the ‘B’ end bogie of the subsequent vehicle decreases. When the pitching angle of the middle coupler is depressed, the derailment trends for the front and rear bogies exhibit the opposite trend from that of the elevation angle. As the train collision speed increases, the pitching motion of the middle coupler is limited to forcing a yawing motion, causing the yawing deflection angle to increase sharply, which causes the wheel–rail lateral force to increase rapidly. From this, the derailment risk of the bogie increases, which further causes large displacement lateral buckling of the train. An anti-lateral buckling device can limit the yawing deflection angle of the middle coupler, preventing lateral buckling from large displacement and decreasing the risk of derailment.     

Improvements for the stability of heavy-haul couplers with arc surface contact

To investigate the stability mechanism of heavy-haul couplers with arc surface contact, the geometry and force analysis were conducted according to the friction circle theory. To improve the stability of the coupler, four improvements were proposed, which are increasing the secondary lateral stiffness of locomotives, adding a restoring bumpstop at the end of the coupler, increasing the arc surfaces radii and changing the clearance and stiffness of secondary lateral stopping block. A multi-body dynamics model with four heavy-haul locomotives and three detailed couplers were established to simulate the emergency braking. In addition, the coupler yaw instability was tested to investigate the effects of relevant parameters on the coupler stability. The results show that increasing the secondary lateral stiffness of locomotives, adding a bumpstop with a smaller bumpstop gap, increasing the arc surfaces radii, increasing the stiffness and decreasing the clearance of secondary lateral stopping block are conducive to improving the stability of the coupler with arc surface contact.     

Dynamic performances of an innovative coupler used in heavy haul trains

An innovative structure for a heavy haul coupler with an arc surface contact and restoring bumpstop is proposed. This coupler has a small lateral force at a small yaw angle and a limitable yaw angle to ensure an allowable coupler lateral force under intense compressive force. The main structural characteristic of the combined contact coupler is a lateral movable follower with an appropriate friction coefficient of 0.06–0.08 and a slide block with a single freedom of longitudinal movement. In order to verify and simulate the performances, a multi-body dynamics model with four heavy haul locomotives and three detailed couplers was established to simulate the process of emergency braking. In addition, the coupler yaw instability and wheel set lateral forces were tested in order to investigate the effect of relevant parameters on the coupler performances. The combined contact coupler is suitable for heavy haul train for a good dynamic performance.     

液力偶合器叶栅附面层及旋涡控制的试验研究

采用在液力偶合器叶片上打孔的方法，控制其内部附面层的发展、分离和旋涡的扩散，以提高偶合器的力矩系数。应用激光切面法测量叶片打孔前后的内部流场，并进行以比分析，得出了叶片上打孔的数量和孔径大小的最佳值。     

An approach for the validation of railway vehicle models based on on-track measurements

This paper proposes an approach for the validation of railway vehicle models based on on-track measurements. The validation of simulation models has gained importance with the introduction of new applications of multi-body simulation in railway vehicle dynamics as the assessment of track geometry defects, the investigation of derailments and the analysis of gauging. These applications are not only interested in qualitative predictions of the vehicle behaviour but also in precise quantitative results of the safety and comfort relevant vehicle responses. The validation process aims at guaranteeing that the simulation model represents the dynamic behaviour of the real vehicle with a sufficient good precision. A misfit function is defined which quantifies the distance between the simulated and the measured vehicle response allowing to evaluate different models at different running conditions. The obtained modelling errors are compared to the measurement uncertainty estimated for one vehicle using repeatability analysis.     

4WD汽车应用粘性联轴器分析

粘性联轴器这一新装置以其独有的特性在四轮驱动汽车上得到广泛应用，粘性联轴器一经确定结构，即可通过转速差自动调节传递转矩的特性，分析了四轮驱动汽车采用粘性联轴器的可能性，介绍了采用粘性联轴器连接的四轮驱动形式和工作原理，阐述了汽车速度，轮胎滑移率对粘性联轴器转速差的影响。     

Simulation of curving at low speed under high traction for passive steering hauling locomotives

The traction control in modern electric and diesel electric locomotives has allowed rail operators to utilise high traction adhesion levels without undue risk of damage from uncontrolled wheel spin. At the same time, some locomotive manufacturers have developed passive steering locomotive bogies to reduce wheel rail wear and further improve locomotive adhesion performance on curves. High locomotive traction loads in curving are known to cause the loss of steering performance in passive steering bogies. At present there are few publications on the curving performance of locomotive steering with linkage bogies. The most extreme traction curving cases of low speed and high adhesion for hauling locomotives have not been fully investigated, with effects of coupler forces and cant excess being generally ignored. This paper presents a simulation study for three axle bogie locomotives in pusher and pulling train positions on tight curves. The simulation study uses moderate and high traction adhesion levels of 16.6% and 37% for various rail friction conditions. Curving performance is assessed, showing forced steering bogies to have considerable advantages over self steering bogies. Likewise it is shown that self steering bogies are significantly better than yaw relaxation bogies at improving steering under traction. As the required traction adhesion approaches the rail friction coefficient, steering performance of all bogies degrades and yaw of the bogie frame relative to the track increases. Operation with excess cant and tensile coupler forces are both found to be detrimental to the wear performance of all locomotive bogies, increasing the bogie frame yaw angles. Bogie frame pitching is also found to have significant effect on steering, causing increased performance differences between bogie designs.     

Effect of arc surfaces friction coefficient on coupler stability in heavy haul locomotives: simulation and experiment

The heavy haul coupler/buffer system equipped with arc surfaces on the coupler tail and the follower is widely applied to connect the locomotives and wagons. As one of the most important parameters, arc surfaces friction coefficient plays a key role in coupler instability, which threatens the safety of trains. To investigate the effect of arc surfaces friction coefficient on coupler stability, a simulation model adopting the latest modelling methods is established and field tests employing the locomotives equipped with different friction coefficients are conducted. The results show that the friction coefficient of arc surfaces can affect the coupler yaw angle remarkably. Increasing the friction coefficient can improve the coupler stability. However, under severe compressive force condition, the increased friction coefficient can be reduced quickly, which calls for further attention.     

一种新型HEV动力耦合器的ADAMS建模与仿真研究

动力耦合器是混合动力汽车的核心部件,对动力耦合器进行相关控制就可以实现混合动力车辆不同模式之间的转换。运用ADAMS仿真软件,对一新型动力耦合器(即汽车上常用差速器的反用)各项功能进行了仿真。仿真结果表明,该新型动力耦合器可以很好地实现预期目标,并得出了相关的运动学与动力学关系式。最后,通过台架试验验证了仿真结果的正确性。     

Berechnung des extremen Lenk- und Bremsverhaltens von Sattelkraftfahrzeugen

Simulation of Steering and Braking Behaviour of Tractor-Semitrailer Vehicles in Extreme Situations

This paper deals with the simulation of the behaviour of tractor-semitrailer vehicles at braking on wet, slippery road surface. The nonlinear model used for the computation enables to simulate extreme situations at wheel locking and swerving

The instabilities during braking such as jackknifing and trailer swing as well as non steerability are investigated. Straightline braking shows the influence of cornering on the behaviour during braking in a turn.     

牵引车-半挂车列车动力学仿真研究

在合理的理论假设基础上建立了较为精细的牵引车-半挂车的整车动力学仿真模型。应用此模型,针对6×4牵引车拖挂2轴半挂车列车的折叠、甩尾、倾翻及转向瞬态响应进行了仿真,并对各工况的特点进行了分析。仿真结果表明该模型能够很好地模拟车辆在各种危险工况下的运动状态,从而为进一步研究牵引车-半挂车列车的性能特点提供了很好的工具。     

Berechnung des extremen Lenk- und Bremsverhaltens von Sattelkraftfahrzeugen

SUMMARY

Simulation of Steering and Braking Behaviour of Tractor-Semitrailer Vehicles in Extreme Situations

This paper deals with the simulation of the behaviour of tractor-semitrailer vehicles at braking on wet, slippery road surface. The nonlinear model used for the computation enables to simulate extreme situations at wheel locking and swerving

The instabilities during braking such as jackknifing and trailer swing as well as non steerability are investigated. Straightline braking shows the influence of cornering on the behaviour during braking in a turn.     

The effect of spring pads in the secondary suspension of railway vehicles on bogie yaw resistance

This paper deals with properties of bogie yaw resistance of an electric locomotive with secondary suspension consisting of flexi-coil springs supplemented with tilting spring pads. Transversal stiffness of a sample of a spring/pad assembly was measured on a dynamic test stand of the University of Pardubice (Czech Republic) and the results were applied into a multi-body model of the locomotive created in the simulation tool ‘SJKV’. On the basis of the simulation results, a detailed analysis of the bogie yaw resistance was performed in order to explain the effect in dynamic behaviour of the locomotive when the moment against bogie rotation (and therefore the distribution of guiding forces on individual wheels, as well) is influenced with the vehicle speed in a certain curve. Results of this analysis show that the application of suspension elements with strongly directionally dependent transversal stiffness into the secondary suspension can just lead to a dependency of the bogie yaw resistance on cant deficiency, i.e. on the vehicle speed in curve. This fact has wide consequences on the vehicle dynamics (especially on the guiding behaviour of the vehicle in curves) and it also points out that the current method of evaluation of the bogie yaw resistance according to relevant standards, which is related with assessment of the quasistatic safety of a railway vehicle against derailment, is not objective enough.