Noise,vibration, harshness model of a rotating tyre

ABSTRACT

The tyre plays a fundamental role in the generation of acoustically perceptible driving noise and vibrations inside the vehicle. An essential part of these vibrations is induced by the road excitation and transferred via the tyre into the vehicle. There are two basic ways to study noise, vibration, harshness (NVH) behaviour: Simulations in time and frequency domains. Modelling the tyre transfer behaviour in frequency domain requires special attention to the rotation of the tyre. This paper shows the approach taken by the authors to include the transfer behaviour in the frequency range up to 250?Hz from geometric road excitations to resulting spindle forces in frequency domain. This paper validates the derived NVH tyre model by comparison with appropriate transient simulations of the base transient model.     

Optimization for Vehicle Suspension I: Time Domain

SUMMARY

A numerical procedure for finding the optimum values of a number of parameters describing a model vehicle suspension has been studied. The vehicle has been modelled by dynamic systems of linear springs and dampers, and the goal is to obtain lower acceleration peaks at an elected design point in the vehicle.

The problem is stated as a mathematical programming problem which can be solved by means of the sequential linear programming technique. The procedure has been implemented for a four wheel independent suspension model capable of being subjected to road irregularities and to centrifugal and braking accelerations.     

Validation of an Articulated Vehicle Simulation

SUMMARY

Tests were performed on a typical UK articulated vehicle to measure dynamic tyre forces and sprung mass accelerations. The measured road profile data and vehicle response data are used to determine some of the important characteristics of articulated vehicle vibration behaviour. In particular, roll motions and their effect on dynamic tyre forces are examined. The measured data are used to validate two and three-dimensional computer models of the vehicle. Attention is given to modelling the tandem leaf-spring trailer suspension. The conditions under which a two-dimensional model can accurately simulate vehicle behaviour are examined.     

Off-Road Vehicle Dynamics

SUMMARY

Recent developments in off-road vehicle dynamics are reviewed. Progress on this topic and the application of new techniques to the particular problemsassociated with off-road operation tend to lag behind practices established for road vehicles.

The factor which limits further progress is the lack ofappropriate off-road tyre data, in particular, on vibrational and lateral force generation characteristics. Also, a long term study should be aimed at understanding the dynamic behaviour of tyres on yielding surfaces.     

Comparison of All-Wheel Steerings in the System Driver-Vehicle

SUMMARY

Different load or tires and a drive on an ice-coated road can overcharge a driver to such an extend, that the result may be an accident. Therefore the aim of development is a self-acting compensation of the vehicle to different vehicle transfer behaviour (invariant vehicle behaviour).

The calculation of so called optimal characteristics shows, that only rear-wheel steering cannot realize this aim of development. Therefore an additional front-wheel angle, which is not influenced by the driver, is necessary. A transfer function can be calculated in order to get controlled steering of the rear wheels without the influence of load.

It is not possible to realize optimal characteristics, because the parameters of the vehicle are difficult to measure. Only an optimal diagnosis and control of driving condition realize a relief for the driver in every driving situation in order to avoid most of the accidents.

The often demanded sideslip angle compensation only worsens driving conditions on ice-coated roads. Therefore systems which identify the driving condition themselves have to be favoured in any case.     

Experimental Study of System Optimization for Suppression of Vehicle Vibration

SUMMARY

The improvements of ride comfort and vehicle maneuverability in the vehicle design can be achieved by using an active suspension. However, the problems in such a control are the complex control logic because of the control laws incompatible with the improvements of ride comfort and maneuverability, and the cost increase because of various sensors to be attached. Therefore, we examined the control abilities of ride comfort and maneuverability on a unique control law using frequency shaped LQ, and controlled the characteristic of the contact between tire and road without a road displacement sensor     

Effect of Connecting the Front and Rear Air Suspensions of a Vehicle on the Transmissibility of Road Undulation Inputs

SUMMARY

Airsprings have been used for vehicle suspensions over the last 40 years. They are mostly used as independent suspensions. Analysis of air springs available in literature is mostly limited to a single-degree-of-freedom system or a two-degrees-of-freedom system only in the translation mode. This paper deals with a model of a vehicle where the front and the rear springs are connected by a capillary tube. A two-degrees-of-freedom model having motion in bounce and pitch mode is presented. Equations of mass flow are linearized on the assumption of small variations in volume and pressure. Expressions for the transmissibility and the phase angle in the bounce and the pitch mode are derived. Road inputs to the front and the rear axles are assumed to be identical except for a phase difference between them. The effect of the capillary flow coefficient and that of the phase angle between the front and the rear axle excitation are studied. It is shown that an optimum value of the capillary flow coefficient exists which minimizes the transmissibility of motion in both modes over the entire frequency range. It is also observed that a phase angle of 180 degrees presents ideal transmissibility characteristics. Thus, a promising application of air springs for a vehicle suspension is presented.     

Random Response of Tractor-Semitrailer System

SUMMARY

This work describes an analytical study of the dynamic behaviour of a tractor-semitrailer vehicle. A digital computer simulation was used to describe the longitudinal, vertical, and pitching motions of the vehicle travelling over a stationary random road surface. A man-seat model was also incorporated into the simulation. Vehicle response to road irregularities has been studied by assuming two different roads for loaded and unloaded cases.

Numerical results are presented for vehicle, showing system eigenvalues, power spectral densities and root mean square values of the linear and angular accelerations and displacements. Vehicle acceleration response is compared with the ISO riding comfort standard. All results for the loaded and unloaded cases and for smooth and rough roads indicated that an uncomfortable ride would result from vehicle response.     

Crosswind Feedforward Control – A Measure to Improve Vehicle Crosswind Behaviour

SUMMARY

The theory of crosswind feedforward control was explained using the example of a vehicle with active front-wheel steering. Beforehand, the calculation formulas and frequency responses of the transient crosswind force and of the wind yaw moment acting on the vehicle were derived using the example of a simple vehicle fluid model. The influence of the transiency of crosswind disturbance on the dynamic crosswind behaviour of a vehicle was then presented. The results of simulation confirmed the analyses carried out in the frequency domain for feedforward control with front, rear and all-wheel steering. With front-wheel steering, the influence of crosswind on one of the vehicle movement variables (lateral acceleration or yaw rate) could be almost completely compensated by dynamic feedforward control. With rear-wheel steering, it is only possible to compensate directly for the influence on the yawing rate. Due to the setting of the side force in the same direction as the lateral wind force at the start, active rear-wheel steering is not so successful as active front-wheel steering. Nevertheless, the crosswind behaviour of a vehicle can be considerably enhanced by feedforward control with rear-wheel steering. The best crosswind behaviour was obtained with active all-wheel steering: the vehicle hardly responds at all to crosswinds and remains on course despite heavy gusts of wind.     

Stationar- und Ubergangsverhalten von Sattel- und Lasttugen bei der Kreisfahrt: Lineare Berechnungen

ABSTRACT

Steady and Transient Turning of Tractor-Semitrailer and Truck-Trailer Combinations: A Linear Analysis

A simplified analysis is made of the yaw stability and control of the two types of the commercial vehicle combinations (tractor-semitrailer, truck-trailer) at a constant forward velocity during steady and transient turning. The combined vehicle is treated as a linear dynamic system (Fig. 2). The steer angle at the front wheels of the tractor (or truck) and the steady-state responses if the road verhicle train (yaw rate, articulation angles and sideslip angle) are calculated (Equations 18 to 25). Exploratory calculations are performed to determine the influence of the cornering stiffness of the tires for the two types of the vehicle combinations upon the steady-state responses (Figs. 7 to 10). For a linear simplified model of articulated vehicle the steady-state turning behaviour is stable also under conditions of rather high driving speed (70 km/h). A simplified analysis of the transient turning behaviour of the two types of road trains has shown the tractor-semitrailer to preserve stability even under driving speeds exceeding 70 km/h (Fig. 13), whereas the truck-trailer combinations appear to become oscillatory unstable if the driving speed rises above the 60 km/h margin (Fig. 14).     

Shear Force Development by Pneumatic Tyres in Steady State Conditions: A Review of Modelling Aspects

SUMMARY

Modelling of the generation of shear forces by pneumatic tyres under steady state conditions is reviewed. The review is placed in a practical context, through reference to the uses to which models may be put by the vehicle dynamicist and the tyre designer. It will be of interest also to the student of rolling contact problems.

The subject is divided into sections, covering physically founded models which require computation for their solution, physically based models which are sufficiently simplified to allow analytical solutions and formula based, empirical models. The classes are more nearly continuous than this strict division would imply, since approximations in obtaining analytical solutions may be made, empirical correction factors may be applied to analytical results and formula based methods may take into account tyre mechanical principles. Such matters are discussed in the relevant sections. Attention is given to the important matter of choosing model parameters to best represent the behaviour of a particular tyre.

Conclusions relate to the structural and frictional mechanisms present in the shear force generation process, the contributions of carcass and tread elastic properties and of geometrical and frictional factors to the determination of the distributions of force through the contact region, the relationship between accuracy and computational load and the selection of methods for modelling tyre forces in a road vehicle dynamics context. Reference to the most pertinent literature in the field is made and possibilities for the further development of the state of the art are mentioned.     

Modelling of Railway Track and Vehicle/Track Interaction at High Frequencies

Abstract

A review is presented of dynamic modelling of railway track and of the interaction of vehicle and track at frequencies which are sufficiently high for the track's dynamic behaviour to be significant. Since noise is one of the most important consequences of wheel/rail interaction at high frequencies, the maximum frequency of interest is about 5kHz: the limit of human hearing. The topic is reviewed both historically and in particular with reference to the application of modelling to the solution of practical problems. Good models of the rail, the sleeper and the wheelset are now available for the whole frequency range of interest. However, it is at present impossible to predict either the dynamic behaviour of the railpad and ballast or their long term behaviour. This is regarded as the most promising area for future research.     

Road roughness estimation based on discrete Kalman filter with unknown input

ABSTRACT

The road roughness acts as a disturbance input to the vehicle dynamics, and causes undesirable vibrations associated with the ride and handing characteristics. Furthermore, the accurate measurement of road roughness plays a key role in better understanding a vehicle dynamic behaviour and active suspension control systems. However, the direct measurement by laser profilometer or other distance sensors are not trivial due to technical and economic issues. This study proposes a new road roughness estimation method by using the discrete Kalman filter with unknown input (DKF-UI). This algorithm is built on a quarter-car model and uses the measurements of the wheel stroke (suspension deflection), and the acceleration of the sprung mass and unsprung mass. The estimation results are compared to the measurements by laser profilometer in-vehicle test.     

Advanced vehicle dynamics of heavy trucks with the perspective of road safety

ABSTRACT

This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.     

Optimal Linear Preview Control of Active Vehicle Suspension

SUMMARY

The problem of linear preview control of vehicle suspension is considered as a continuous time stochastic optimal control problem. In the proposed approach minimal a priori information about the road irregularities is assumed and measurement errors are taken into account. It is shown that estimation and control issues can be decoupled. The problem formulation and the analytical solution are given in a general form and hence they apply to other problems in which the system disturbances are unknown a priori, even in a stochastic sense, but some preview information is possible.

The solution is applied to a two-degree-of-freedom (2-DOF) vehicle model. The effects of preview information on ride comfort, road holding, working space of the suspension and power requirements are examined in time and frequency domains. The results show that the greatest potential is for improving road holding properties. This effect could not have been observed in previous studies based on a 1-DOF vehicle model. It is also demonstrated that the presence of preview drastically reduces power requirements, thus relieving the performance versus actuator power dilemma.     

Roadway Elevation Profile Generation for Vehicle Simulation

SUMMARY

With a simplified approach for creating road surface elevation information for simulation of vehicle vertical response to roadway unevenness, roadways for single and parallel track simulations and averaged roads for variable velocity simulation are developed. Sets of correctly chosen random roadway slopes are averaged appropriately for the variable velocity simulation. The procedure generates approximately “white” slope spectral density roadways in the frequency ranges of interest, and the elevation profiles are representative of average road profiles. The method is simple in practice yet suffices for many parameter studies of suspensions and vehicle dynamics.     

Simulation of the Interaction between Vehicle Wheel and the Unevenness of Road Surface

SUMMARY

A model of the relationship between a vehicle wheel and the unevenness of the road surface is defined. The wheel is considered to be of circular shape. For a given form of unevenness, the excitation functions are evaluated for the individual subsystems of the dynamic vehicle model having 5 degrees of freedom. The vehicle model traverses the uneven surface at a variable velocity. The model provides for the study of the complex dynamic phenomena which occur between the wheel and the unevenness. The response of the model also includes the dynamic stress on the drive when the wheel passes over the unevenness of the road surface.