Simulation of curving at low speed under high traction for passive steering hauling locomotives

The traction control in modern electric and diesel electric locomotives has allowed rail operators to utilise high traction adhesion levels without undue risk of damage from uncontrolled wheel spin. At the same time, some locomotive manufacturers have developed passive steering locomotive bogies to reduce wheel rail wear and further improve locomotive adhesion performance on curves. High locomotive traction loads in curving are known to cause the loss of steering performance in passive steering bogies. At present there are few publications on the curving performance of locomotive steering with linkage bogies. The most extreme traction curving cases of low speed and high adhesion for hauling locomotives have not been fully investigated, with effects of coupler forces and cant excess being generally ignored. This paper presents a simulation study for three axle bogie locomotives in pusher and pulling train positions on tight curves. The simulation study uses moderate and high traction adhesion levels of 16.6% and 37% for various rail friction conditions. Curving performance is assessed, showing forced steering bogies to have considerable advantages over self steering bogies. Likewise it is shown that self steering bogies are significantly better than yaw relaxation bogies at improving steering under traction. As the required traction adhesion approaches the rail friction coefficient, steering performance of all bogies degrades and yaw of the bogie frame relative to the track increases. Operation with excess cant and tensile coupler forces are both found to be detrimental to the wear performance of all locomotive bogies, increasing the bogie frame yaw angles. Bogie frame pitching is also found to have significant effect on steering, causing increased performance differences between bogie designs.     

Simulation of active steering control for curving under traction in hauling locomotives

Active steering control in the form of secondary yaw control (SYC) and actuated wheelset yaw (AWY) have been in prototype development. This paper presents a new active steering bogie design, actuated yaw force steering (AY-FS), that is able to steer under high traction loads in tight curves. The AY-FS bogie design is compared with the AWY design. The steering performance AWY under high traction loads has not been previously reported. This paper examines five control methods, three for AWY and two for AY-FS bogies and assesses the traction curving and stability control performance of the alternative designs and control methods compared with each other and to passive steering bogie designs. The curving performance results showed considerable advantage in the proposed AY-FS bogies over the AWY. It was shown that control must be applied to both the yaw angle and the steering angle of the bogie to achieve the best traction steering performance which was not possible with the AWY bogies. The proposed new bogie designs of AY-FS overall give better traction curving and stability performance than the AWY designs.     

Theoretical Comparison Between Different Configurations of Radial and Conventional Bogies

This article compares the dynamic behaviour of different configurations of radial and conventional two-axle bogies. In general, the design parameters for a better curve negotiation are not compatible with those for good stability. As the main target of this article is to compare the curving performances of different bogies under the same design basis, several bogie configurations with the same level of stability, obtained by choosing proper primary suspension stiffnesses, have been used. The comparison includes a conventional bogie and three radial bogies with differing self-steering and forced-steering principles in three different passenger services: High Speed, Regional and Mass Transit. The analysis has been concentrated on parameters such as stability, lateral wheel-track forces in curve and wheel wear indices. The results show that the radial bogie configurations studied do not make significant contributions in general applications with regard to a conventional bogie. It is only under specific running conditions and types of service that some radial bogie configurations provide advantages with respect to the conventional bogie.     

Theoretical Comparison Between Different Configurations of Radial and Conventional Bogies

This article compares the dynamic behaviour of different configurations of radial and conventional two-axle bogies. In general, the design parameters for a better curve negotiation are not compatible with those for good stability. As the main target of this article is to compare the curving performances of different bogies under the same design basis, several bogie configurations with the same level of stability, obtained by choosing proper primary suspension stiffnesses, have been used. The comparison includes a conventional bogie and three radial bogies with differing self-steering and forced-steering principles in three different passenger services: High Speed, Regional and Mass Transit. The analysis has been concentrated on parameters such as stability, lateral wheel-track forces in curve and wheel wear indices. The results show that the radial bogie configurations studied do not make significant contributions in general applications with regard to a conventional bogie. It is only under specific running conditions and types of service that some radial bogie configurations provide advantages with respect to the conventional bogie.     

Conceptual design of high-speed semi-low-floor bogie for train-tram

Train-tram railway vehicles implement the connection between urban tramlines and the surrounding railway network. Train-tram railway vehicles, which use existing infrastructure, can help to avoid large investments in new railways or tramlines and make interchanges between city center and surrounding cities unnecessary. However, present train-tram rail vehicle cannot carry out the integration of operating by means of high speed in intercity railways with operating on small radius of curvature in inner city tramlines. This paper aims to develop a new model for solid wheelsets train-tram railway vehicles, which will not only pass the curve of 25mR radius of curvature traveling on inner city tramlines with the speed of 18 km/h, but also can travel on straight railway with 200 km/h high speed between intercity. In this paper, a new train-tram model, including five car-body and five motor bogies with ten traction motors, is addressed. Expect as a real rail vehicle testing, this study prefer virtual simulation, which is an effective way to show the rail vehicle performance, such as ride stability, ride comfort and ride safety, by means of evaluating the dynamic characteristics of rail vehicle. Moreover, Design of Experiment (DOE) method is used to optimize solid wheelsets bogie system on improving passenger comfort, safety and stability of train-tram. Parameters of components of bogie system are tuned to minimize the derailment coefficient and the ride comfort index. The results shows that the best comfort index for passenger and minimum derailment coefficient are found. The results also show that this optimized new train-tram model is reliable and practical enough to be applied on real rail vehicle design.     

Recent Development in Active Steering of Railway Vehicles

Summary This paper presents the recent development on active steering for railway vehicles, and carries out a technical appraisal of different actuation schemes and control approaches. It brings together the latest research activities and findings for the full active steering techniques for rail vehicles with the solid-axle wheelsets, independently-rotating wheelsets and wheel-pairs without axles, but relevant work on passive and semi-active solutions is also briefly described. Potential benefits of the use of a combination of modern control technology and mechatronic approach are evaluated, and in particular solutions for the difficult design trade-off between the stability and the curving performance are presented. Various actuation configurations are discussed, and advantages and drawbacks of those schemes are investigated. The outline design using a number of control methods is analysed, and measurement requirement and state estimation techniques essential for implementation of the active steering schemes are also explored. In addition the issue of safety criticality is highlighted and a possible approach for developing fault-tolerant systems is proposed. Overall the paper provides an authoritative assessment of the major advances in actively-steered wheels and addresses outstanding critical issues.     

Static and Dynamic Instabilities of Bogie Railway Vehicles with Linkage Steered Wheelsets

The root loci of a type of bogie railway vehicle with linkage steered wheelsets are discussed and contrasted with those of conventional configurations. Approximate solutions of the equations of motion are used to derive stability criteria associated with the various modes of static and dynamic instability that are identified. The physical origin of each form of instability is discussed. It is shown that, in addition to the more common forms of dynamic instability arising from the joint action of creep, conicity and inertia, other forms of static and oscillatory instability are the result of structural asymmetry and wheelset articulation.     

Dynamics of Automated Guideway Transit Vehicle with Single-axle Bogies

Summary The steering type of a mechanical guidance system has been used for Automated Guideway Transit (AGT) system in Japan. Recently, the single-axle bogie system has developed for AGT vehicle and applied to Yurikamome 7200 type vehicle. This paper describes dynamic characteristics of AGT vehicle with single-axle bogies. Introducing a nonlinear, 15 degree-of-freedom dynamic model, a computer simulation study on the lateral motion of the AGT vehicle with single-axle bogies are carried out. In order to show the dynamic characteristics of the single-axle bogie clearly, it is compared to that of the AGT vehicle with conventional steering system. The simulation study with actual vehicle parameters shows that single-axle bogie has suitable characteristics for AGT system. The multi-body dynamics modeler, DADS, is used to build the dynamic model of AGT vehicle with single-axle bogies and this is used to demonstrate the vehicle motion in actual guideway. Obtained results are compared to that of the field test. It is shown that the vehicle dynamic response can be obtained in realistic situation by using multibody dynamics code, that is useful for designing both vehicle and guideway.     

Dynamics of Automated Guideway Transit Vehicle with Single-axle Bogies

Summary The steering type of a mechanical guidance system has been used for Automated Guideway Transit (AGT) system in Japan. Recently, the single-axle bogie system has developed for AGT vehicle and applied to Yurikamome 7200 type vehicle. This paper describes dynamic characteristics of AGT vehicle with single-axle bogies. Introducing a nonlinear, 15 degree-of-freedom dynamic model, a computer simulation study on the lateral motion of the AGT vehicle with single-axle bogies are carried out. In order to show the dynamic characteristics of the single-axle bogie clearly, it is compared to that of the AGT vehicle with conventional steering system. The simulation study with actual vehicle parameters shows that single-axle bogie has suitable characteristics for AGT system. The multi-body dynamics modeler, DADS, is used to build the dynamic model of AGT vehicle with single-axle bogies and this is used to demonstrate the vehicle motion in actual guideway. Obtained results are compared to that of the field test. It is shown that the vehicle dynamic response can be obtained in realistic situation by using multibody dynamics code, that is useful for designing both vehicle and guideway.     

Some Basic Properties of Bogies, an Analytical Approach

An important function of a bogie of a railway vehicle (or of the running gear of guided vehicles in general) is to guide or steer the vehicle along the course of the track while isolating the vehicle and its payload as well as possible from unintended but inevitable imperfections in the position of the track. Against this background, an analytical expression is derived for the low speed transfer function of a bogie, from which conclusions can be drawn regarding the effect of the elastic connections between wheelsets on dynamic behaviour. At higher speeds inertia effects of the unsprung masses have a negative effect on dynamic behaviour, the magnitude of this effect being different for different types of elastic connections. This is also reflected in the critical speed and the interaction between body and bogie. With respect to the wear of wheels and rails on curved track, the range of radii of curves which can be traversed without flange contact and, for smaller radii, the rate of increase of flange force and angle of attack of the leading wheelset are important factors. Some expressions are derived for the effect of the elastic connections between wheelsets on these factors.     

Solid Axle and Independently-Rotating Railway Wheelsets - A Control Engineering Assessment of Stability

Block diagram representations of both conventional wheelsets and wheelsets with independently-rotating wheels are developed, with the objective of giving insights from a control engineering viewpoint for studies of actively-controlled wheelsets. The analysis predicts a quasi-kinematic oscillation with independently-rotating wheels which has not been reported before. It also identifies possibilities for control approaches which might be used to stabilise a wheelset without affecting steady-state curving performance.     

Solid Axle and Independently-Rotating Railway Wheelsets - A Control Engineering Assessment of Stability

Block diagram representations of both conventional wheelsets and wheelsets with independently-rotating wheels are developed, with the objective of giving insights from a control engineering viewpoint for studies of actively-controlled wheelsets. The analysis predicts a quasi-kinematic oscillation with independently-rotating wheels which has not been reported before. It also identifies possibilities for control approaches which might be used to stabilise a wheelset without affecting steady-state curving performance.     

Flutter and Divergence Instabilities in Systems of Railway Wheelsets with Semi-rigid Articulation

For railway vehicles having coned wheels mounted on solid axles there is, in general, a conflict between stability of lateral deviations from the motion along the track and ability to steer round curves. However, certain configurations of three-axle vehicle can satisfy the requirement of perfect curving and for certain values of the system parameters are dynamically stable. In the case where three wheelsets have semi-rigid articulation and either the distribution of conicity amongst the wheelsets or the position of the articulation joint are varied, it is shown that both flutter and divergence instabilities can occur at low speeds, in contrast to the more common dynamic instabilities of other forms of railway vehicle which are driven by the inertia forces.     

A semi-active control suspension system for railway vehicles with magnetorheological fluid dampers

The high-speed train has achieved great progress in the last decades. It is one of the most important modes of transportation between cities. With the rapid development of the high-speed train, its safety issue is paid much more attention than ever before. To improve the stability of the vehicle with high speed, extra dampers (i.e. anti-hunting damper) are used in the traditional bogies with passive suspension system. However, the curving performance of the vehicle is undermined due to the extra lateral force generated by the dampers. The active suspension systems proposed in the last decades attempt to solve the vehicle steering issue. However, the active suspension systems need extra actuators driven by electrical power or hydraulic power. There are some implementation and even safety issues which are not easy to be overcome. In this paper, an innovative semi-active controlled lateral suspension system for railway vehicles is proposed. Four magnetorheological fluid dampers are fixed to the primary suspension system of each bogie. They are controlled by online controllers for enhancing the running stability on the straight track line on the one hand and further improving the curving performance by controlling the damper force on the other hand. Two control strategies are proposed in the light of the pure rolling concept. The effectiveness of the proposed strategies is demonstrated by SIMPACK and Matlab co-simulation for a full railway vehicle with two conventional bogies.     

Steering and Dynamic Stability of Railway Vehicles

For railway vehicles having coned wheels mounted on solid axles there is a conflict between dynamic stability and steering ability

It is shown that the stiffness and kinematic properties of all possible interwheelset connections are characterised by two properties describing the distortional characteristics of the vehicle in plan. Within this framework, the various possibilities for steered wheelsets are considered, and several past and current proposals are reviewed. Using the linear approach to dynamic stabibty and curve negotation the performance of existing and newly proposed configurations is discussed

For any symmetric, two-axle vehicle it is shown that for perfect steering on a curve there should be zero bending stiffness between the wheelsets. It is further shown that if the bending stiffness is zero, the vehicle lacks dynamic stability as the critical speed of instability, is zero. In this case, the vehicle undergoes a steering oscillation which occurs at the kinematic frequency of a single wheelset and which is a motion in which pure rolling occurs

Similar results are obtained with vehicles with three or more axles if adjacent axles are connected by shear structures. However, it is shown that it is possible to satisfy both the requirements of perfect steering and a non-zero critical speed if the vehicle has zero bending stiffness and if, in addition to adjacent wheelsets being connected in shear, at least one pair of non-adjacent axles are connected by a shear structure.     

Efficiency analysis of a multiple axle vehicle with hydrostatic transmission overcoming obstacles

Transmission configurations in off-road vehicles with multiple driven axles can be a determining factor in the obstacle surmounting capacity and also in the vehicle efficiency. An off-road articulated vehicle with four driven axles, four bogies and two modules has been considered for the global hydrostatic transmission efficiency analysis and for the vehicle functional efficiency analysis. The power flow through the transmission system has been quantified from the combustion engine shaft to each axle of the wheels. It has been done for different the operating conditions and taking into account the wheel–terrain interaction and the transmission configuration, that could lead to a forced slippage of some of the wheels. Results show the influence of the different wheels’ requirements, the transmission configuration limitations and the considered control strategy on the global transmission and vehicle functional efficiencies.     

Steering and Dynamic Stability of Railway Vehicles

SUMMARY

For railway vehicles having coned wheels mounted on solid axles there is a conflict between dynamic stability and steering ability

It is shown that the stiffness and kinematic properties of all possible interwheelset connections are characterised by two properties describing the distortional characteristics of the vehicle in plan. Within this framework, the various possibilities for steered wheelsets are considered, and several past and current proposals are reviewed. Using the linear approach to dynamic stabibty and curve negotation the performance of existing and newly proposed configurations is discussed

For any symmetric, two-axle vehicle it is shown that for perfect steering on a curve there should be zero bending stiffness between the wheelsets. It is further shown that if the bending stiffness is zero, the vehicle lacks dynamic stability as the critical speed of instability, is zero. In this case, the vehicle undergoes a steering oscillation which occurs at the kinematic frequency of a single wheelset and which is a motion in which pure rolling occurs

Similar results are obtained with vehicles with three or more axles if adjacent axles are connected by shear structures. However, it is shown that it is possible to satisfy both the requirements of perfect steering and a non-zero critical speed if the vehicle has zero bending stiffness and if, in addition to adjacent wheelsets being connected in shear, at least one pair of non-adjacent axles are connected by a shear structure.     

Method for obtaining the modal properties of articulated trains equipped with independently rotating wheels

Independently rotating wheels in railway vehicles could represent an alternative to standard technology as a solution to dynamic problems such as hunting instability or steering forces in curves. Among the proposed design solutions, the train with independently rotating wheels and with the most practical applications is that developed by Talgo. The Talgo technology is based on the use of a passive steering technique of the wheelset through a mechanism. The absence of automatic control systems means that a careful selection of the mechanical parameters of the vehicle is required to improve its dynamic characteristics. Aspects such as dynamic stability or the effect of vibration on passenger comfort could be analysed by extracting the modal properties of the train from mathematical models. In this article, a methodology for determining the low-frequency modal properties of articulated trains equipped with independently rotating wheels and passive steering system (Talgo-type) is proposed. The singularity of this application based on the use of non-conventional wheelsets necessarily involves the development of a specific methodology.