Experimental Study of System Optimization for Suppression of Vehicle Vibration

The improvements of ride comfort and vehicle maneuverability in the vehicle design can be achieved by using an active suspension. However, the problems in such a control are the complex control logic because of the control laws incompatible with the improvements of ride comfort and maneuverability, and the cost increase because of various sensors to be attached. Therefore, we examined the control abilities of ride comfort and maneuverability on a unique control law using frequency shaped LQ, and controlled the characteristic of the contact between tire and road without a road displacement sensor     

The Development and Implementation of Adaptive Semi-Active Suspension Control*

SUMMARY

Using adjustable shock absorbers within vehicle suspension systems, it is possible to improve ride comfort significantly when a control strategy is applied based on the so-called skyhook principle. However, the drawback is a poorly damped wheel-hop mode which makes the road holding ability worse. Using adaptive semi-active suspension control based on the tire load variations as introduced in this paper, the trade-off between road holding and ride comfort can be relaxed. Implementation of adaptive skyhook control requires the determination of a number of important and difficult to measure states of the vehicle. This can either be accomplished by several sensors and filters or by a state estimator in combination with less sensors and an internal model of the vehicle. Both methods are discussed. Finally some preliminary test results are discussed.     

Magneto-rheological suspensions for improving ground vehicle’s ride comfort,stability, and handling

ABSTRACT

A state-of-the-art discussion on the applications of magneto-rheological (MR) suspensions for improving ride comfort, handling, and stability in ground vehicles is discussed for both road and rail applications. A historical perspective on the discovery and engineering development of MR fluids is presented, followed by some of the common methods for modelling their non-Newtonian behaviour. The common modes of the MR fluids are discussed, along with the application of the fluid in valve mode for ground vehicles’ dampers (or shock absorbers). The applications span across nearly all road vehicles, including automobiles, trains, semi-trucks, motorcycles, and even bicycles. For each type of vehicle, the results of some of the past studies is presented briefly, with reference to the originating study. It is discussed that Past experimental and modelling studies have indicated that MR suspensions provide clear advantages for ground vehicles that far surpasses the performance of passive suspension. For rail vehicles, the primary advantage is in terms of increasing the speed at which the onset of hunting occurs, whereas for road vehicles – mainly automobiles – the performance improvements are in terms of a better balance between vehicle ride, handling, and stability. To further elaborate on this point, a single-suspension model is used to develop an index-based approach for studying the compromise that is offered by vehicle suspensions, using the H₂ optimisation approach. Evaluating three indices based on the sprung-mass acceleration, suspension rattlespace, and tyre deflection, it is clearly demonstrated that MR suspensions significantly improve road vehicle’s ride comfort, stability, and handling in comparison with passive suspensions. For rail vehicles, the simulation results indicate that using MR suspensions with an on-off switching control can increase the speed at which the on-set of hunting occurs by as much as 50% to more than 300%.     

Advanced Control Methods of Active Suspension

SUMMARY

This paper describes new control methods for the active suspension. For improving ride comfort further, preview control rule is proposed. For improving stability further, roll stiffness distribution control rule is examined by the test vehicle. Simulations and vehicle driving tests are conducted to confirm the effect of these new control methods. The results of simulations and vehicle driving tests show in our research phase that preview control can achieve a substantial improvement in ride comfort and application of roll stiffness distribution control provides a large improvement in stability     

Optimal Linear Preview Control of Active Vehicle Suspension

SUMMARY

The problem of linear preview control of vehicle suspension is considered as a continuous time stochastic optimal control problem. In the proposed approach minimal a priori information about the road irregularities is assumed and measurement errors are taken into account. It is shown that estimation and control issues can be decoupled. The problem formulation and the analytical solution are given in a general form and hence they apply to other problems in which the system disturbances are unknown a priori, even in a stochastic sense, but some preview information is possible.

The solution is applied to a two-degree-of-freedom (2-DOF) vehicle model. The effects of preview information on ride comfort, road holding, working space of the suspension and power requirements are examined in time and frequency domains. The results show that the greatest potential is for improving road holding properties. This effect could not have been observed in previous studies based on a 1-DOF vehicle model. It is also demonstrated that the presence of preview drastically reduces power requirements, thus relieving the performance versus actuator power dilemma.     

Preview suspension control for a full tracked vehicle

In this study, preview control algorithms for the active and semi-active suspension systems of a full tracked vehicle (FTV) are designed based on a 3-D.O.F model and evaluated. The main issue of this study is to make the ride comfort characteristics of a fast moving tracked vehicle better to keep an operator’s driving capability. Since road wheels almost trace the profiles of the road surface as long as the track doesn’t depart from the ground, the preview information can be obtained by measuring only the absolute position or velocity of the first road wheel. Simulation results show that the performance of the sky-hook suspension system almost follows that of full state feedback suspension system and the on-off semi-active system carries out remarkable performance with the combination of 12 on-off semi-active suspension units. The results simulated with 1^st and 2^nd weighting sets mean that the suspension system combined with the soft type of inner suspension and hard type of outer suspension can carry out better ride comfort characteristics than that with identical suspensions. The full tracked vehicle (FTV) system is uncontrollable and the system is split into controllable and uncontrollable subspace using singular value decomposition transformation. Frequency response curves to four types of inputs, such as heaving, pitching, rolling, and warping inputs, also demonstrate the merits of preview control in ride comfort. All the frequency characteristic responses confirm the continuous time results.     

Stochastic Optimal Control of Highway Tractors with Active Suspensions

Stochastic optimal control and estimation theories are used to design an active suspension system for a cab ride in a tractor-semitrailer vehicle. A discrete-continuous vehicle model with eleven degrees of freedom is augmented by a stochastic road excitation model and a human perception of vibration shape filter. Both perfect measurement and estimated state cases are considered. The impact of the measurement noise on the design of the optimal controller is demonstrated. The performance of the optimally controlled system is compared with an optimal passive system. It is shown that significant improvements in ride comfort can be achieved through the use of actively controlled cab suspensions.     

Random Response of Tractor-Semitrailer System

SUMMARY

This work describes an analytical study of the dynamic behaviour of a tractor-semitrailer vehicle. A digital computer simulation was used to describe the longitudinal, vertical, and pitching motions of the vehicle travelling over a stationary random road surface. A man-seat model was also incorporated into the simulation. Vehicle response to road irregularities has been studied by assuming two different roads for loaded and unloaded cases.

Numerical results are presented for vehicle, showing system eigenvalues, power spectral densities and root mean square values of the linear and angular accelerations and displacements. Vehicle acceleration response is compared with the ISO riding comfort standard. All results for the loaded and unloaded cases and for smooth and rough roads indicated that an uncomfortable ride would result from vehicle response.     

汽车平顺性时域仿真分析

采用虚拟试验场技术进行了汽车行驶平顺性的时域仿真。建立了面向汽车平顺性分析的整车刚弹耦合有限元模型,同时建立了脉冲输入路面模型和随机输入路面模型。采用1/3倍频带分布加速度均方根值方法及总加权方法对试验车辆的平顺性进行了评价。试验结果表明,运用虚拟试验场技术能够真实地反映汽车的行驶平顺性,仿真分析结果可靠。     

轮毂电机驱动电动汽车3种构型的平顺性分析

针对轮毂电机驱动电动汽车3种构型,对其平顺性问题展开研究。分别采用滤波白噪声方法和三角形凸块描述随机路面激励和脉冲路面激励。建立了轮毂电机驱动电动汽车3种构型的振动模型,确定了相应的平顺性评价指标。在随机路面和脉冲路面下,采用Matlab/Simulink仿真了轮毂电机驱动电动汽车3种构型的平顺性。研究结果表明,具有吸振结构的构型2和具有悬置结构的构型3与传统悬架的构型1相比,降低了轮毂电机驱动电动汽车随机路面和脉冲路面的平顺性评价指标。     

I. Minutes of the IAVSD Board Meetings

SUMMARY

A theoretical analysis is presented to model a hydromechanical, semi-active suspension system, first as a single wheel station and then as fitted to each wheel of an off-road vehicle. Predicted results show that two benefits are obtained by comparison with the equivalent passive system. First, vehicle attitude is controlled for changes in body forces arising from static loads or braking/cornering inputs. Second, a significant improvement in ride comfort is obtained because low suspension stiffnesses can be used.     

Comparison of Ride Comfort Criteria for Computer Optimization of Vehicles Travelling on Randomly Profiled Roads

SUMMARY

This paper discusses and compares some ride comfort criteria which may be suitable for randomly vibrating vehicles. The criteria consider single-figure measures based on response mean square spectral densities for plane linear combined vehicle-passenger models. Eight different measures divided into three groups are studied. The two vehicle suspension damper stiffnesses are numerically optimized with respect to the eight measures of ride comfort. The results are compared and discussed. Two optimizations with respect to five vehicle parameters are also reported.     

The Development and Implementation of Adaptive Semi-Active Suspension Control*

Using adjustable shock absorbers within vehicle suspension systems, it is possible to improve ride comfort significantly when a control strategy is applied based on the so-called skyhook principle. However, the drawback is a poorly damped wheel-hop mode which makes the road holding ability worse. Using adaptive semi-active suspension control based on the tire load variations as introduced in this paper, the trade-off between road holding and ride comfort can be relaxed. Implementation of adaptive skyhook control requires the determination of a number of important and difficult to measure states of the vehicle. This can either be accomplished by several sensors and filters or by a state estimator in combination with less sensors and an internal model of the vehicle. Both methods are discussed. Finally some preliminary test results are discussed.     

基于柔性模型的多轴汽车平顺性的仿真研究

基于弹性梁弯曲振动理论和模态分析法建立了多轴汽车平顺性分析的柔性模型。按照汽车行驶平顺性评价方法，运用建立的柔性模型，分析了车速、路面等级、悬挂质量的分布、车架刚度以及悬架系统的刚度和阻尼对多轴汽车平顺性的影响。分析结果表明：悬挂质量的弯曲振动是影响多轴汽车行驶平顺性的一个不可忽略的重要因素；常用的刚体模型不能准确地描述多轴汽车的平顺性，不适合用于多轴汽车平顺性的分析。     

Active lateral secondary suspension with H ∞ control to improve ride comfort: simulations on a full-scale model

In this study, a full-scale rail vehicle model is used to investigate how lateral ride comfort is influenced by implementing the H _∞ and sky-hook damping control strategies. Simulations show that significant ride comfort improvements can be achieved on straight track with both control strategies compared with a passive system. In curves, it is beneficial to add a carbody centring Hold-Off Device (HOD) to reduce large spring deflections and hence to minimise the risk of bumpstop contact. In curve transitions, the relative lateral displacement between carbody and bogie is reduced by the concept of H _∞ control in combination with the HOD. However, the corresponding concept with sky-hook damping degrades the effect of the carbody centring function. Moreover, it is shown that lateral and yaw mode separation is a way to further improve the performance of the studied control strategies.     

Frequency-domain method for evaluating the ride comfort of a motorcycle

In many European towns, the demand for fast and efficient mobility is frequently satisfied by means of two-wheeled vehicles. The improvement of comfort of two-wheeled vehicles used by tired and busy workers can increase safety in ground transport. Nowadays, multibody codes make it possible to predict the ride comfort of two-wheeled vehicles by means of time-domain or frequency-domain simulations. Comfort indices can be developed by post-processing the results of numerical simulations. This task is difficult, because the indices should depend on vehicle characteristics and should be independent of road quality and vehicle speed. Poor quality roads may generate nonlinear effects. Speed influences the trim of the vehicle and the wheelbase filtering, which takes place because the same road unevenness excites the front and rear wheel with a time delay which depends on the vehicle’s speed.

In this paper, the comfort of two-wheeled vehicles is studied by means of a frequency-domain approach. The wheelbase filtering is averaged considering typical missions of the vehicle. The missions are journeys with a forward speed that assumes different values according to a probability density function. Indices of comfort are calculated taking into account the human sensitivity. The examples show that the proposed comfort indices depend on suspensions’ characteristics and, hence, are useful design tools. Finally, some time-domain calculations are carried out to give emphasis to nonlinear effects and to show the limits of the frequency-domain analysis.     

松软路面突变性对车辆垂向振动的影响

为了在越野行驶车辆平顺性仿真系统中实时动态反映车辆的振动特性,提出了基于小波变换的松软越野路面突变性描述方法并分析突变性对车辆垂向振动的影响。通过小波变换对路面奇异点进行测定和定位,把越野车辆平顺性仿真系统看作是在有限时间内受到随机载荷激励的动力系统,分析其受路面突变载荷的车辆的垂直振动响应方差。结果表明,小波变换能较准确地判定路面奇异点并对其定位,可为越野车辆平顺性虚拟测试系统提供路面随机输入。     

Development of Preview Active Suspension Control System and Performance Limit Analysis by Trajectory Optimization

The main role of the suspension system is to achieve ride comfort by reducing vibrations generated by the road roughness. The active damper is getting much attention due to its reduced cost and ability to enhance ride comfort especially when the road ahead is measurable by an environment sensor. In this study a preview active suspension control system was developed in order to improve ride comfort when the vehicle is passing over a speed bump. The control system consists of a feedback controller based on the skyhook logic and a feedforward controller for canceling out the road disturbance. The performance limit for the active suspension control system was computed via trajectory optimization to provide a measure against which to compare and validate the performance of the developed controller. The simulation results indicated that the controller of this study could enhance ride comfort significantly over the active suspension control system employing only the skyhook feedback control logic. Also the developed controller, by displaying similar control pattern as the trajectory optimization during significant time portions, proved that its control policy is legitimate.     

基于行驶舒适性的路桥过渡段差异沉降控制标准

从人车路相互作用出发,建立了人车路系统振动方程和路桥过渡段路面不平整模型,并通过编制的RCBP程序分析了车辆行驶舒适性的影响因素,最后确定了基于行驶舒适性的路桥过渡段差异沉降控制标准。结果不仅可以用于路桥过渡段差异沉降控制标准的相关规范,也可用于一般路基差异沉降标准的制定,对桥头跳车问题的处治和路桥过渡段路面的养护维修提供了科学决策依据。     

汽车转向与悬架系统的集成控制研究

在建立了汽车转向与悬架系统的综合模型的基础上,运用一种具有扩展的调节器结构LQG控制方法,设计了 主动悬架控制器,实现对车身横摆角速度、车身垂直加速度、车身侧倾角和俯仰角的集成控制,从而显著提高汽车的 平顺性、操纵稳定性和安全性。