Stability enhancement and fuel economy of the 4-wheel-drive hybrid electric vehicles by optimal tyre force distribution

In this paper, vehicle stability control and fuel economy for a 4-wheel-drive hybrid vehicle are investigated. The integrated controller is designed within three layers. The first layer determines the total yaw moment and total lateral force made by using an optimal controller method to follow the desired dynamic behaviour of a vehicle. The second layer determines optimum tyre force distribution in order to optimise tyre usage and find out how the tyres should share longitudinal and lateral forces to achieve a target vehicle response under the assumption that all four wheels can be independently steered, driven, and braked. In the third layer, the active steering, wheel slip, and electrical motor torque controllers are designed. In the front axle, internal combustion engine (ICE) is coupled to an electric motor (EM). The control strategy has to determine the power distribution between ICE and EM to minimise fuel consumption and allowing the vehicle to be charge sustaining. Finally, simulations performed in MATLAB/SIMULINK environment show that the proposed structure could enhance the vehicle stability and fuel economy in different manoeuvres.     

A combined-slip predictive control of vehicle stability with experimental verification

In this paper, a model predictive vehicle stability controller is designed based on a combined-slip LuGre tyre model. Variations in the lateral tyre forces due to changes in tyre slip ratios are considered in the prediction model of the controller. It is observed that the proposed combined-slip controller takes advantage of the more accurate tyre model and can adjust tyre slip ratios based on lateral forces of the front axle. This results in an interesting closed-loop response that challenges the notion of braking only the wheels on one side of the vehicle in differential braking. The performance of the proposed controller is evaluated in software simulations and is compared to a similar pure-slip controller. Furthermore, experimental tests are conducted on a rear-wheel drive electric Chevrolet Equinox equipped with differential brakes to evaluate the closed-loop response of the model predictive control controller.     

Design of tyre force excitation for tyre–road friction estimation

Knowledge of the current tyre–road friction coefficient is essential for future autonomous vehicles. The environmental conditions, and the tyre–road friction in particular, determine both the braking distance and the maximum cornering velocity and thus set the boundaries for the vehicle. Tyre–road friction is difficult to estimate during normal driving due to low levels of tyre force excitation. This problem can be solved by using active tyre force excitation. A torque is added to one or several wheels in the purpose of estimating the tyre–road friction coefficient. Active tyre force excitation provides the opportunity to design the tyre force excitation freely. This study investigates how the tyre force should be applied to minimise the error of the tyre–road friction estimate. The performance of different excitation strategies was found to be dependent on both tyre model choice and noise level. Furthermore, the advantage with using tyre models with more parameters decreased when noise was added to the force and slip ratio.     

A model-based traction control strategy non-reliant on wheel slip information

A traction control system (TCS) for two-wheel-drive vehicles can conveniently be realised by means of slip control. Such a TCS is modified in this paper in order to be applicable to four-wheel-drive vehicles and anti-lock braking systems, where slip information is not readily available. A reference vehicle model is used to estimate the vehicle velocity. The reference model is excited by a saw-tooth signal in order to adapt the slip for maximum tyre traction performance. The model-based TCS is made robust to vehicle modelling errors by extending it with (i) a superimposed loop of tyre static curve gradient control or (ii) a robust switching controller based on a bi-directional saw-tooth excitation signal. The proposed traction control strategies are verified by experiments and computer simulations.     

Estimation of the tyre–road maximum friction coefficient and slip slope based on a novel tyre model

In this article, a new approach to estimate the vehicle tyre forces, tyre–road maximum friction coefficient, and slip slope is presented. Contrary to the majority of the previous work on this subject, a new tyre model for the estimation of the tyre–road interface characterisation is proposed. First, the tyre model is built and compared with those of Pacejka, Dugoff, and one other tyre model. Then, based on a vehicle model that uses four degrees of freedom, an extended Kalman filter (EKF) method is designed to estimate the vehicle motion and tyre forces. The shortcomings of force estimation are discussed in this article. Based on the proposed tyre model and the improved force measurements, another EKF is implemented to estimate the tyre model parameters, including the maximum friction coefficient, slip slope, etc. The tyre forces are accurately obtained simultaneously. Finally, very promising results have been achieved for pure acceleration/braking for varying road conditions, both in pure steering and combined manoeuvre simulations.     

Velocity and normal tyre force estimation for heavy trucks based on vehicle dynamic simulation considering the road slope angle

A precise estimation of vehicle velocities can be valuable for improving the performance of the vehicle dynamics control (VDC) system and this estimation relies heavily upon the accuracy of longitudinal and lateral tyre force calculation governed by the prediction of normal tyre forces. This paper presents a computational method based on the unscented Kalman filter (UKF) method to estimate both longitudinal and lateral velocities and develops a novel quasi-stationary method to predict normal tyre forces of heavy trucks on a sloping road. The vehicle dynamic model is constructed with a planar dynamic model combined with the Pacejka tyre model. The novel quasi-stationary method for predicting normal tyre forces is able to characterise the typical chassis configuration of the heavy trucks. The validation is conducted through comparing the predicted results with those simulated by the TruckSim and it has a good agreement between these results without compromising the convergence speed and stability.     

Sliding mode-based lateral vehicle dynamics control using tyre force measurements

In this work, a lateral vehicle dynamics control based on tyre force measurements is proposed. Most of the lateral vehicle dynamics control schemes are based on yaw rate whereas tyre forces are the most important variables in vehicle dynamics as tyres are the only contact points between the vehicle and road. In the proposed method, active front steering is employed to uniformly distribute the required lateral force among the front left and right tyres. The force distribution is quantified through the tyre utilisation coefficients. In order to address the nonlinearities and uncertainties of the vehicle model, a gain scheduling sliding-mode control technique is used. In addition to stabilising the lateral dynamics, the proposed controller is able to maintain maximum lateral acceleration. The proposed method is tested and validated on a multi-body vehicle simulator.     

Using the lead vehicle as preview sensor in convoy vehicle active suspension control

Both ride quality and roadholding of actively suspended vehicles can be improved by sensing the road ahead of the vehicle and using this information in a preview controller. Previous applications have used look-ahead sensors mounted on the front bumper to measure terrain beneath. Such sensors are vulnerable, potentially confused by water, snow, or other soft obstacles and offer a fixed preview time. For convoy vehicle applications, this paper proposes using the overall response of the preceding vehicle(s) to generate preview controller information for follower vehicles. A robust observer is used to estimate the states of a quarter-car vehicle model, from which road profile is estimated and passed on to the follower vehicle(s) to generate a preview function. The preview-active suspension, implemented in discrete time using a shift register approach to improve simulation time, reduces sprung mass acceleration and dynamic tyre deflection peaks by more than 50% and 40%, respectively. Terrain can change from one vehicle to the next if a loose obstacle is dislodged, or if the vehicle paths are sufficiently different so that one vehicle misses a discrete road event. The resulting spurious preview information can give suspension performance worse than that of a passive or conventional active system. In this paper, each vehicle can effectively estimate the road profile based on its own state trajectory. By comparing its own road estimate with the preview information, preview errors can be detected and suspension control quickly switched from preview to conventional active control to preserve performance improvements compared to passive suspensions.     

Active yaw damper for the improvement of railway vehicle stability and curving performances: simulations and experimental results

To further increase passenger train comfort and handling performances, a mechatronic approach to the design of railway vehicles is necessary. In fact, active systems on board a railway vehicle allow to push design barriers beyond those encountered with just passive systems. The article deals with the development of an electro-mechanical actuator to improve the running behaviour of a railway vehicle, both in straight track and curve. The main components of the active system are a brushless motor and a mechanical transmission, used to apply a longitudinal force between the carbody and the bogie of the vehicle. The actuator is operated in force control. Different control strategies were developed for straight track running, where the aim is to increase the vehicle critical speed, and for curve negotiation, where the goal is to reduce the maximum values of track shift forces. A mathematical model of the railway vehicle incorporating the active control device has been developed and used to optimise control strategies and hardware set-up of the active device and to estimate the increase in operating performances with respect to a conventional passive vehicle. The active control device has then been mounted on an ETR470 railway vehicle, and its performances have been evaluated during in-line tests in both straight and curved tracks.     

Vehicle-Generated Road Damage: A Review

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

Identifying tyre models directly from vehicle test data using an extended Kalman filter

Individual tyre models are traditionally derived from component tests, with their parameters matched to force and slip measurements. They are imported into vehicle models which should, but do not always properly provide suspension geometry interaction. Recent advances in Global Positioning System (GPS)/inertia vehicle instrumentation now make full state measurement viable in test vehicles, so tyre slip behaviour is directly measurable. This paper uses an extended Kalman filter for system identification, to derive individual load-dependent tyre models directly from these test vehicle state measurements. The resulting model therefore implicitly compensates for suspension geometry and compliance. The paper looks at two variants of the tyre model, and also considers real-time adaptation of the model to road surface friction variations. Test vehicle results are used exclusively, and the results show successful tyre model identification, improved vehicle model state prediction – particularly in lateral velocity reproduction – and an effective real-time solution for road friction estimation.     

Active yaw damper for the improvement of railway vehicle stability and curving performances: simulations and experimental results

To further increase passenger train comfort and handling performances, a mechatronic approach to the design of railway vehicles is necessary. In fact, active systems on board a railway vehicle allow to push design barriers beyond those encountered with just passive systems. The article deals with the development of an electro-mechanical actuator to improve the running behaviour of a railway vehicle, both in straight track and curve. The main components of the active system are a brushless motor and a mechanical transmission, used to apply a longitudinal force between the carbody and the bogie of the vehicle. The actuator is operated in force control. Different control strategies were developed for straight track running, where the aim is to increase the vehicle critical speed, and for curve negotiation, where the goal is to reduce the maximum values of track shift forces. A mathematical model of the railway vehicle incorporating the active control device has been developed and used to optimise control strategies and hardware set-up of the active device and to estimate the increase in operating performances with respect to a conventional passive vehicle. The active control device has then been mounted on an ETR470 railway vehicle, and its performances have been evaluated during in-line tests in both straight and curved tracks.     

Design of safety-oriented control allocation strategies for overactuated electric vehicles

The new vehicle platforms for electric vehicles (EVs) that are becoming available are characterised by actuator redundancy, which makes it possible to jointly optimise different aspects of the vehicle motion. To do this, high-level control objectives are first specified and solved with appropriate control strategies. Then, the resulting virtual control action must be translated into actual actuator commands by a control allocation layer that takes care of computing the forces to be applied at the wheels. This step, in general, is quite demanding as far as computational complexity is considered. In this work, a safety-oriented approach to this problem is proposed. Specifically, a four-wheel steer EV with four in-wheel motors is considered, and the high-level motion controller is designed within a sliding mode framework with conditional integrators. For distributing the forces among the tyres, two control allocation approaches are investigated. The first, based on the extension of the cascading generalised inverse method, is computationally efficient but shows some limitations in dealing with unfeasible force values. To solve the problem, a second allocation algorithm is proposed, which relies on the linearisation of the tyre–road friction constraints. Extensive tests, carried out in the CarSim simulation environment, demonstrate the effectiveness of the proposed approach.     

Robust cascade control for the horizontal motion of a vehicle with single-wheel actuators

The article presents a cascade control for the horizontal motion of a vehicle with single-wheel actuators. The outer control loop for the longitudinal and lateral accelerations and the yaw rate ensures a desired vehicle motion. By a combination of state feedback control and observer-based disturbance feedforward the inner control loop robustly stabilises the rotating and steering motions of the wheels in spite of unknown frictions between tyres and ground. Since the three degrees of freedom of the horizontal motion are affected by eight tyre forces, the vehicle considered is an over-actuated system. Thus additional control objectives can be realised besides the desired motion trajectory as, for example, a maximum in driving safety. The corresponding analytical tyre force allocation also guarantees real-time capability because of its relatively low computational effort. Provided suitable fault detection and isolation are available, the proposed cascade control has the potential of fault-tolerance, because the force allocation is adaptable. Another benefit results from the modular control structure, because it allows a stepwise implementation. Besides, it only requires a small number of measurements for control purposes. These measurements are the rotational speeds and steering angles of the wheels, the longitudinal and lateral acceleration and the yaw rate of the vehicle.     

Comparative study of vehicle tyre–road friction coefficient estimation with a novel cost-effective method

This paper qualitatively and quantitatively reviews and compares three typical tyre–road friction coefficient estimation methods, which are the slip slope method, individual tyre force estimation method and extended Kalman filter method, and then presents a new cost-effective tyre–road friction coefficient estimation method. Based on the qualitative analysis and the numerical comparisons, it is found that all of the three typical methods can successfully estimate the tyre force and friction coefficient in most of the test conditions, but the estimation performance is compromised for some of the methods during different simulation scenarios. In addition, all of these three methods need global positioning system (GPS) to measure the absolute velocity of a vehicle. To overcome the above-mentioned problem, a novel cost-effective estimation method is proposed in this paper. This method requires only the inputs of wheel angular velocity, traction/brake torque and longitudinal acceleration, which are all easy to be measured using available sensors installed in passenger vehicles. By using this method, the vehicle absolute velocity and slip ratio can be estimated by an improved nonlinear observer without using GPS, and the friction force and tyre–road friction coefficient can be obtained from the estimated vehicle velocity and slip ratio. Simulations are used to validate the effectiveness of the proposed estimation method.     

Implementation of active steering on longer combination vehicles for enhanced lateral performance

A steering-based controller for improving lateral performance of longer combination vehicles (LCVs) is proposed. The controller steers the axles of the towed units to regulate the time span between the driver steering and generation of tyre lateral forces at the towed units and consequently reduces the yaw rate rearward amplification (RWA) and offtracking. The open-loop effectiveness of the controller is evaluated with simulations and its closed loop or driver in the loop effectiveness is verified on a test track with a truck–dolly–semitrailer test vehicle in a series of single- and double-lane change manoeuvres. The developed controller reduces the yaw rate RWA and offtracking considerably without diminishing the manoeuvrability. Furthermore, as a byproduct, it decreases the lateral acceleration RWA moderately. The obtained safety improvements by the proposed controller can promote the use of LCVs in traffic which will result in the reduction of congestion problem as well as environmental and economic benefits.     

An alternative approach to automotive ESC based on measured wheel forces

Traditional electronic stability control (ESC) systems act on one or more wheels on the basis of a logic aiming at the control of variables that cannot be directly measured (vehicle sideslip angle and the tyre slip). Hence, a vehicle state estimator capable of evaluating the needed variables from the data of the input sensors is necessary. In the present paper, the authors discuss a different approach to the estimation problem, assuming that the forces acting on the wheels can be directly measured. The ESC feed-forward control logic is designed through a vehicle frequency response analysis in order to obtain a faster active system activation. The variable controlled by the logic is the tyre longitudinal force. Experimental results obtained on an ESC hardware-in-the-loop test bench prove the validity of the approach, showing enhanced dynamic performances, together with the limits due to the delays in the actuation of the ESC motor pump, which needs some time to build the pressure requested for the intervention on the selected callipers. Finally, the tests demonstrate the opportunity of closing the control loop on a variable (i.e. the force) that can be directly measured.     

Rail Vehicles' Riding Quality and Comfort Related to Theoretical and Experimental Optimization Application to High Speed Trains

SUMMARY

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

基于小波控制的电动汽车稳定性研究（双语出版）

针对前轮独立驱动电动汽车,研究一种基于小波控制器的驱动稳定性控制系统。为提高车辆对开路面的行驶稳定性,根据驱动轮等转矩分配控制策略,提出基于神经网络PID的驱动轮滑移率相近为目标控制策略。针对矢量控制中的电流控制,提出基于离散小波变换的电流控制器。通过CarSim/Simulink建立前轮独立驱动电动汽车联合仿真平台,进行不同工况整车性能仿真与分析,并基于A&D5435快速原型开发平台进行实车试验。仿真与试验结果表明：基于小波控制器的驱动控制系统不仅提高了车辆对开路面行驶的稳定性,而且具有更平滑、更快速的转矩响应;对开路面工况下,提出的控制策略左侧、右侧驱动轮速度仿真结果与试验结果最大偏差分别为3.43%和3.56%;等转矩分配控制策略下,左侧、右侧驱动轮速度仿真结果与试验结果最大偏差分别为3.86%和3.25%,表明了试验与仿真的一致性;对开路面仿真工况下,相比于驱动轮等转矩分配控制策略,基于神经网络PID的驱动轮滑移率相近为目标控制策略的车辆峰值质心侧偏角降低了79.57%,侧向跑偏距离降低了73.39%。     

低附着弯道路面车辆制动力控制策略研究

分析了车辆ABS系统在弯道制动时存在的横向稳定性问题,提出了一种低附着弯道路面车辆制动力控制策略.它综合考虑车轮防抱死与车辆发生侧滑时所能承受的最大侧向力,根据两者所允许的最大制动力中较小值确定施加于车辆的制动力.所进行的数值仿真结果表明该控制方法能提高车辆在低附着弯道路面上的横向稳定性.