A passenger car driver model for higher lateral accelerations

Due to increasing demands for time and cost efficient vehicle and driver assistant systems development, numerical simulation of closed-loop manoeuvres becomes increasingly important. Thus, the driver has to be considered in the modelling. On the basis of a two-layer approach to model a driver's steering behaviour, the field of application is extended to higher lateral accelerations in this study. An analytical method to determine the driver parameters is presented, which is based on the two-wheel vehicle model. The simulation results are determined using a full vehicle model including all essential nonlinearities. Standard manoeuvres in the nonlinear range of vehicle handling behaviour are performed. A cornering manoeuvre is chosen to show the characteristics of the proposed driver model.     

Effects of Model Complexity on the Performance of Automated Vehicle Steering Controllers: Controller Development and Evaluation

SUMMARY

Due to increased traffic congestion and travel times, research in Advanced Vehicle Control Systems (AVCS) has focused on automated lateral and headway control. Automated vehicles are seen as a way to increase freeway capacity and vehicle speeds while reducing accidents due to human error. Recent research in automated lateral control has focused on vehicle control during low-g maneuvers. To increase safety, automated lateral controllers will need to recognize and react to emergency situations.

This paper investigates the effects of vehicle and tire model order on the response of automated vehicles to an emergency step lane change using a controller based on linear vehicle and tire models. From these studies it is concluded that control strategies based solely on linear vehicle and tire models are inadequate for emergency vehicle maneuvers.

A strategy is then proposed to automatically control vehicles through emergency maneuvers. Here the response of a nonlinear vehicle model is used with a linear state model to optimize controller gains for nonlinear maneuvers. An emergency step lane change is used as a preliminary test of the method.     

基于Volterra理论的扁平箱梁气动力非线性特性研究

为了研究扁平箱梁断面气动力系统的非线性特性,采用Volterra理论和CFD方法,对丹麦大带东桥主桥加劲梁断面的气动力特性进行研究。利用脉冲激励模型分别作竖弯和扭转运动,并基于CFD一次数值模拟,对大带东桥扁平箱梁断面气动力系统的Volterra级数核进行识别,建立扁平箱梁断面气动力系统的非线性离散时间Volterra级数模型,该模型可以快速给出任意简谐激励下的气动力响应,无需耗时很久的CFD模拟。分别基于竖弯和扭转向的强迫简谐位移激励,使用Volterra级数气动力模型对大带东桥扁平箱梁断面的气动力系统进行仿真,将得到的仿真时程与CFD模拟结果进行对比,分析振动频率和幅值对扁平箱梁断面气动力系统非线性特性的影响。结果表明：忽略二阶及以上非线性高阶项得到的Volterra级数模型给出的气动力估计与CFD模拟差别很小;扁平箱梁断面气动力的高阶非线性效应较小,其为弱气动力非线性系统;在研究的强迫运动位移幅值和频率范围内,扁平箱梁断面的气动力模型响应没有表现出对振动幅值和频率的显著相关性,且仿真值与CFD模拟值的最大相对精度误差不超过10%。     

Unscented Kalman filter for vehicle state estimation

Vehicle dynamics control (VDC) systems require information about system variables, which cannot be directly measured, e.g. the wheel slip or the vehicle side-slip angle. This paper presents a new concept for the vehicle state estimation under the assumption that the vehicle is equipped with the standard VDC sensors. It is proposed to utilise an unscented Kalman filter for estimation purposes, since it is based on a numerically efficient nonlinear stochastic estimation technique. A planar two-track model is combined with the empiric Magic Formula in order to describe the vehicle and tyre behaviour. Moreover, an advanced vertical tyre load calculation method is developed that additionally considers the vertical tyre stiffness and increases the estimation accuracy. Experimental tests show good accuracy and robustness of the designed vehicle state estimation concept.     

Adaptive Throttle Control for Speed Tracking

SUMMARY

Electronic throttle control is an important part of every advanced vehicle control system. In this paper we design an adaptive control scheme for electronic throttle that achieves good tracking of arbitrary constant speed commands in the presence of unknown disturbances. The design is based on a simplified linear vehicle model which is derived from a validated nonlinear one. The designed control scheme is simulated using the validated full order nonlinear vehicle model and tested on an actual vehicle. The simulation and vehicle test results are included in this paper to show the performance of the controller. Due to the learning capability of the adaptive control scheme, changes in the vehicle dynamics do not affect the performance of the controller in any significant manner.     

基于虚拟迭代技术的中型货车驾驶室载荷谱的求取

某货车驾驶室疲劳载荷激励输入位置位于驾驶室与悬置连接处,在进行整车强化道路耐久试验时无法安装设备直接采集。为获取较为准确的驾驶室疲劳寿命分析载荷谱,对强化耐久路面下整车加速度响应信号进行虚拟迭代。虚拟迭代时需调用整车多体动力学模型,为提高整车模型精度,基于Craig-Bampton综合模态理论生成柔性体车架,建立刚柔耦合的整车多体动力学模型。将Femfat-lab与ADAMS/Car进行联合仿真计算,以白噪声为初始输入,求解刚柔耦合整车多体动力学模型的非线性传递函数,基于循环迭代原理,进行各种典型强化路况下驾驶室悬置附近加速度响应信号的虚拟迭代。利用时域信号对比法及损伤阈值法作为迭代收敛判据,获得满足精度需求的位移驱动信号。将位移驱动信号导入到ADAMS/Car中,对整车多体动力学模型进行驱动仿真,提取驾驶室疲劳分析所需激励载荷谱,将虚拟迭代求得的载荷谱用于疲劳寿命分析所得结果与驾驶室疲劳强化台架试验结果进行对比。研究结果表明：出现疲劳破坏的部位相同度达75%,疲劳寿命误差在20%左右,表明虚拟迭代过程中基于柔性体车架建立的刚柔耦合多体动力学模型的仿真计算,可获得较高精度的迭代结果;以位移谱驱动整车多体动力学模型进行仿真能够有效避免六分力直接驱动时模型翻转等不稳定现象,并且整车模型仿真加速度响应结果与实测相应位置加速度响应吻合度较高;相比于传统的疲劳分析载荷获取方法,虚拟迭代技术可以在较低试验成本的情况下获取较高精度的载荷谱,并能够提取由于连接位置导致的无法直接进行载荷测量部位的疲劳分析载荷。     

Improved calibration of simulation models in railway dynamics: application of a parameter identification process to the multi-body model of a TGV train

This paper aims at estimating the vehicle suspension parameters of a TGV (Train à Grande Vitesse) train from measurement data. A better knowledge of these parameters is required for virtual certification or condition monitoring applications. The estimation of the parameter values is performed by minimising a misfit function describing the distance between the measured and the simulated vehicle response. Due to the unsteady excitation from the real track irregularities and nonlinear effects in the vehicle behaviour, the misfit function is defined in the time domain using a least squares estimation. Then an optimisation algorithm is applied in order to find the best parameter values within the defined constraints. The complexity of the solution surface with many local minima requires the use of global optimisation methods. The results show that the model can be improved by this approach providing a response of the simulation model closer to the measurements.     

Fault detection and isolation for a full-scale railway vehicle suspension with multiple Kalman filters

Reliability and dependability in complex mechanical systems can be improved by fault detection and isolation (FDI) methods. These techniques are key elements for maintenance on demand, which could decrease service cost and time significantly. This paper addresses FDI for a railway vehicle: the mechanical model is described as a multibody system, which is excited randomly due to track irregularities. Various parameters, like masses, spring- and damper-characteristics, influence the dynamics of the vehicle. Often, the exact values of the parameters are unknown and might even change over time. Some of these changes are considered critical with respect to the operation of the system and they require immediate maintenance. The aim of this work is to detect faults in the suspension system of the vehicle. A Kalman filter is used in order to estimate the states. To detect and isolate faults the detection error is minimised with multiple Kalman filters. A full-scale train model with nonlinear wheel/rail contact serves as an example for the described techniques. Numerical results for different test cases are presented. The analysis shows that for the given system it is possible not only to detect a failure of the suspension system from the system's dynamic response, but also to distinguish clearly between different possible causes for the changes in the dynamical behaviour.     

Analysis Method of Head-on Vehicle Collision

In this paper a method of analysis of vehicle head-on collision, based on the concept of dispersion of stress waves in rods upon axial impact has been presented. The mathematical model of collision studied here described the vehicle behaviour in collision in terms of a one-dimensional, nonhomo-geneous, nonlinear partial differential equation. A procedure of model identification and some remarks concerning experimental data have been discussed. Results of computer simulation of a tested vehicle have been given.     

Tyre–road grip coefficient assessment. Part 1: off-line methodology using multibody dynamic simulation and genetic algorithms

A key factor to understand the vehicle dynamic behaviour is to know as accurately as possible the interaction that occurs between the tyre and the road, since it depends on many factors that influence the dynamic response of the vehicle. This paper aims to develop a methodology in order to characterise the tyre–road behaviour, applying it to obtain the tyre–road grip coefficient. This methodology is based on the use of dynamic simulation of a virtual model, integrated into a genetic algorithm that identifies the tyre–road friction coefficient in order to adjust the response obtained by simulation to real data. The numerical model was developed in collaboration with SEAT Technical Centre and it was implemented in multibody dynamic simulation software Adams®, from MSC®.     

A passenger car driver model for higher lateral accelerations

Due to increasing demands for time and cost efficient vehicle and driver assistant systems development, numerical simulation of closed-loop manoeuvres becomes increasingly important. Thus, the driver has to be considered in the modelling. On the basis of a two-layer approach to model a driver's steering behaviour, the field of application is extended to higher lateral accelerations in this study. An analytical method to determine the driver parameters is presented, which is based on the two-wheel vehicle model. The simulation results are determined using a full vehicle model including all essential nonlinearities. Standard manoeuvres in the nonlinear range of vehicle handling behaviour are performed. A cornering manoeuvre is chosen to show the characteristics of the proposed driver model.     

Adaptive Throttle Control for Speed Tracking

Electronic throttle control is an important part of every advanced vehicle control system. In this paper we design an adaptive control scheme for electronic throttle that achieves good tracking of arbitrary constant speed commands in the presence of unknown disturbances. The design is based on a simplified linear vehicle model which is derived from a validated nonlinear one. The designed control scheme is simulated using the validated full order nonlinear vehicle model and tested on an actual vehicle. The simulation and vehicle test results are included in this paper to show the performance of the controller. Due to the learning capability of the adaptive control scheme, changes in the vehicle dynamics do not affect the performance of the controller in any significant manner.     

An approach for the validation of railway vehicle models based on on-track measurements

This paper proposes an approach for the validation of railway vehicle models based on on-track measurements. The validation of simulation models has gained importance with the introduction of new applications of multi-body simulation in railway vehicle dynamics as the assessment of track geometry defects, the investigation of derailments and the analysis of gauging. These applications are not only interested in qualitative predictions of the vehicle behaviour but also in precise quantitative results of the safety and comfort relevant vehicle responses. The validation process aims at guaranteeing that the simulation model represents the dynamic behaviour of the real vehicle with a sufficient good precision. A misfit function is defined which quantifies the distance between the simulated and the measured vehicle response allowing to evaluate different models at different running conditions. The obtained modelling errors are compared to the measurement uncertainty estimated for one vehicle using repeatability analysis.     

The effect of wheel set gyroscopic action on the hunting stability of high-speed trains

This study explores the effects of wheel set gyroscopic action on hunting stability by calculating linear and nonlinear critical speeds. First, a dynamic model for a high-speed vehicle with 23 degrees of freedom is developed by considering wheel set gyroscopic action. The linear and nonlinear critical speeds are calculated by eigenvalue analysis and drawing a bifurcation map, respectively. Two computer programs for linear and nonlinear stability analysis are developed. Second, based on an actual high-speed vehicle in China, the effects of wheel set gyroscopic action on hunting stability are quantitatively investigated using computer simulation. Furthermore, the difference between the effects of gyroscopic moments about the x-axis and z-axis is discussed. The results show that the moment about the x-axis is harmful to hunting stability, but the moment about the z-axis is beneficial to hunting stability. However, the integrated effect of these two moments can enhance the critical speeds and suppress the hunting motion.     

An efficient sensitivity analysis method for modified geometry of Macpherson suspension based on Pearson correlation coefficient

The main purpose of this paper is to propose a new method for designing Macpherson suspension, based on the Sobol indices in terms of Pearson correlation which determines the importance of each member on the behaviour of vehicle suspension. The formulation of dynamic analysis of Macpherson suspension system is developed using the suspension members as the modified links in order to achieve the desired kinematic behaviour. The mechanical system is replaced with an equivalent constrained links and then kinematic laws are utilised to obtain a new modified geometry of Macpherson suspension. The equivalent mechanism of Macpherson suspension increased the speed of analysis and reduced its complexity. The ADAMS/CAR software is utilised to simulate a full vehicle, Renault Logan car, in order to analyse the accuracy of modified geometry model. An experimental 4-poster test rig is considered for validating both ADAMS/CAR simulation and analytical geometry model. Pearson correlation coefficient is applied to analyse the sensitivity of each suspension member according to vehicle objective functions such as sprung mass acceleration, etc. Besides this matter, the estimation of Pearson correlation coefficient between variables is analysed in this method. It is understood that the Pearson correlation coefficient is an efficient method for analysing the vehicle suspension which leads to a better design of Macpherson suspension system.     

基于神经网络的半主动悬架自适应模糊控制

提出了基于神经网络的自适应模糊控制策略。模糊控制主要用来对付系统的非线性；神经网络根据振动响应的方差递推结果来辨识车体的振动情况实时调节模糊控制器的量化因子，使模糊控制器对路面的变化具有自适应的能力。在半主动悬挂1／4车非线性模型的基础上进行了仿真研究。     

Vehicle dynamics control using an active third-axle system

This paper introduces the active third-axle system as an innovative vehicle dynamic control method. This method can be applicable for different kinds of three-axle vehicles such as buses, trucks, or even three-axle passenger cars. In this system, an actuator on the middle axle actively applies an independent force on the suspension to improve the handling characteristics, and hence, its technology is similar to slow-active suspension systems. This system can change the inherent vehicle dynamic characteristics, such as under/over steering behaviour, in the linear handling region, as well as vehicle stability in the nonlinear, limit handling region. In this paper, our main focus is to show the potential capabilities of this method in enhancing vehicle dynamic performance. For this purpose, as the first step, the proposed method in both linear and nonlinear vehicle handling regions is studied mathematically. Next, a comprehensive, nonlinear, 10 degrees of freedom vehicle model with a fuzzy control strategy is used to evaluate the effectiveness of this system. The dynamic behaviour of a vehicle, when either uncontrolled or equipped with the active third axle is then compared. Simulation results show that this active system can be considered as an innovative method for vehicle dynamic control.     

Two degrees of freedom PID multi-controllers to design a mathematical driver model: experimental validation and robustness tests

This paper proposes a mathematical driver model based on PID multi-controllers having two degrees of freedom. Each PID controller making up this model is synthesised by the Ziegler–Nichols oscillation method, using the linear time invariant models which are obtained around their nominal operating points. Different PID controllers are combined using nonlinear optimisation and the H _∞ constraint. To demonstrate its robustness, it was tested on two models: a linear parameter variant model and a nonlinear four-wheel model. It was also tested in situations of high dynamic demand. The driver model showed good performance, stability and trajectory tracking. The performance tests were carried out using experimental data acquired by a Laboratory Peugeot 307 developed by INRETS-MA. This driver model was developed for an application known as ‘Itinerary Rupture DIagnosis’ (DIARI), which aims to evaluate the physical limits of a vehicle negotiating a bend. DIARI requires a tool to determine the steering commands to be applied to a vehicle model, making extrapolations with respect to speed.     

Emergency steering control of autonomous vehicle for collision avoidance and stabilisation

ABSTRACT

Collision avoidance and stabilisation are two of the most crucial concerns when an autonomous vehicle finds itself in emergency situations, which usually occur in a short time horizon and require large actuator inputs, together with highly nonlinear tyre cornering response. In order to avoid collision while stabilising autonomous vehicle under dynamic driving situations at handling limits, this paper proposes a novel emergency steering control strategy based on hierarchical control architecture consisting of decision-making layer and motion control layer. In decision-making layer, a dynamic threat assessment model continuously evaluates the risk associated with collision and destabilisation, and a path planner based on kinematics and dynamics of vehicle system determines a collision-free path when it suddenly encounters emergency scenarios. In motion control layer, a lateral motion controller considering nonlinearity of tyre cornering response and unknown external disturbance is designed using tyre lateral force estimation-based backstepping sliding-mode control to track a collision-free path, and to ensure the robustness and stability of the closed-loop system. Both simulation and experiment results show that the proposed control scheme can effectively perform an emergency collision avoidance manoeuvre while maintaining the stability of autonomous vehicle in different running conditions.