Tangential force variation due to the bogie direction reversal procedure

A range of tangential forces is generated within the contact patch when a wheelset moves on the rail. These forces are intensified when incorporating curved tracks and motored axle rail vehicles [Arrus, P., de Pater, A.D. and Meyers, P., 2002, The stationary motion of a one-axle vehicle along a circular curve with real rail and wheel profiles. Vehicle System Dynamics, 37(1), 29-58]. The wheelset is subject to flange contact if an unbalanced force remains in a curve towards the high rail gauge face. The resultant force in the transverse direction includes the lateral force, the radial force, and the creep forces in addition to the effect of the frequent wheelset displacement due to the kinematic oscillation [Iwnicki, S., 2003, Simulation of wheel-rail contact forces. Fatigue Fracture Engineering Material Structure, 26, 887-900]. This article has focused on a potential variation in some of the forces cited when the wheelset is subject to backward and forward movements. A severe wear rate observed within the wheel flange region in Iranian Railways was investigated by operating a test bogie on a curvaceous track. An obvious improvement in the wear rate and wear pattern of the wheels was attained when the second test bogie encountered a bogie direction reversal procedure. This enhancement is considered in this article from the force analysis standpoint.     

Carbody elastic vibrations of high-speed vehicles caused by bogie hunting instability

In particular locations of the high-speed track, the worn wheel profile matched up with the worn rail profile will lead to an extremely high-conicity wheel–rail contact. Consequently, the bogie hunting instability arises, which further results in the so-called carbody shaking phenomenon. In this paper, the carbody elastic vibrations of a high-speed vehicle in service are firstly introduced. Modal tests are conducted to identity the elastic modes of the carbody. The ride comfort and running safety indices for the tested vehicle are evaluated. The rigid–flexible coupling dynamic model for the high-speed passenger car is then developed by using the FE and MBS coupling approach. The rail profiles in those particular locations are measured and further integrated into the simulation model to reproduce the bogie hunting and carbody elastic vibrations. The effects of wheel and rail wear on the vehicle system response, e.g. wheelset bifurcation graph and carbody vibrations, are studied. Two improvement measures, including the wheel profile modification and rail grinding, are proposed to provide possible solutions. It is found that the wheel–rail contact conicity can be lowered by decreasing wheel flange thickness or grinding rail corner, which is expected to improve the bogie hunting stability under worn rail and worn wheel conditions. The carbody elastic vibrations caused by bogie hunting instability can be further restrained.     

A Theory of Wheelset Forces for Two Point Contact Between Wheel and Rail

This paper describes a quasistatic theory of wheelset forces for an important practical case of the wheelset rolling when one of the wheels touches the rail in two contact zones. One of these zones lies on the tread and the other on the wheel flange. For such contact the specific problem of finding the distribution of forces between the tread and flange arises. The simultaneous frictional rolling contact problems for both contact zones have been described with Kalker×apos;s non-linear theory and wheelset equilibrium equations.

The numerical results presented are for an individual wheelset on straight track, the distribution of forces being described for a wide range of loading conditions. The influence of steering on the distribution of forces has also been presented.

This theory can be easily extended for quasistatic curving of railway vehicles and may assist wear studies for vehicles with worn wheels.     

Dynamic performance of high-speed train passing windbreak breach under unsteady crosswind

Field test and computational fluid dynamics (CFD) method are conducted to investigate the safety of high-speed train under unsteady crosswind. Wheel–rail forces of high-speed train passing a breach between two windbreaks under strong crosswind are measured in a field test. The derailment coefficient of first wheelset of front car at the windward side reaches the allowable value. Meanwhile, the left and right of lateral wheel–rail force are in the opposite direction. This kind of phenomenon has not been tested before. Therefore, CFD and multi-body simulations are performed in order to study the phenomena. Good agreement is obtained between the simulation results and the experimental data. It is concluded that the sudden increase of transient aerodynamic loads, when the train passing the breach, is the root of this phenomenon; after running along the same direction as carbody and bogie run along the opposite direction during the high-speed train passing the windbreak breach; larger opposite longitudinal creeping forces of first wheelset compel the first wheelset to yaw toward the windward side; meanwhile, larger lateral wheel–rail forces compel the first wheelset to run toward the windward side rail; the left and right lateral wheel–rail forces become opposite because the right wheel impacts the windward side rail.     

Rail vehicle wheel wear prediction: a comparison between analytical and experimental approaches

There are a number of theoretical and practical techniques to compute rail vehicle wheel wear. For instance, the Archard equation is a well-known tool to determine the worn volume in sliding contact, as a function of normal load, sliding distance and the surface hardness. Of course, the wear coefficient (called K) used in this equation to differentiate the wear models implicitly comprises the conditions that govern the contact surface. Two situations can be taken into account when considering a sliding contact in a rail vehicle wheels, particularly along a curved track: (i) when the radial force prevails the lateral tangential force, which is mainly the frictional force but before flanging and (ii) during flange contact. Also, the Archard equation is employed within the tread and flange regions separately, both the regions being of interest in this paper. A number of approaches are then used to find the distance slid. The authors compare the field test results and the outcome of the analytical approaches. When the wheel wear results acquired from the two test bogies on Iranian Railways, all technical (rigid frame bogies with new assemblies and components) and operational items were identical, except for changing the bogie orientation in the second test trial for a short period. Good agreement was found between the analytical and practical investigations.     

Study on the derailment behaviour of a railway wheelset with solid axles in a railway turnout

ABSTRACT

Dynamic wheel–rail interaction in railway turnouts is more complicated than on ordinary track. In order to evaluate the derailment behaviour of railway wheelsets in railway turnouts, this paper presents a study of dynamic wheel–rail interaction during a wheel flange climbs on the turnout rails, by applying the elasticity positioning wheelset model. A numerical model is established based on a coupled finite element method and multi-body dynamics, and applied to study the derailment behaviour of a railway wheelset in both the facing and trailing directions in a railway turnout, as well as dynamic wheel–turnout rail interaction during the wheel flange climbing on the turnout rails. The influence of the wheel–rail attack angle and the friction coefficient on the dynamic derailment behaviour is investigated through the proposed model. The results show that the derailment safety for a wheelset passing the railway turnout in facing direction is significantly lower than that for the trailing direction and the ordinary track. The possibility of derailment for the wheelset passing the railway turnout in facing and trailing directions at positive wheel–rail attack angles will increase with an increase in the attack angles, and the possibility of derailment can be reduced by decreasing the friction coefficient.     

Study on flange climb derailment criteria of a railway wheelset

The wheel flange climb derailment, which can be usually considered as a quasi-static process, is one of the main types of derailment, and often occurs on curved tracks due to large wheel lateral force and reduced vertical force. The general formula for the wheel critical derailment coefficient Q/P, the ratio of wheel lateral force to vertical force, is derived through analysing the forces exerted on the flange climb wheel. Based on the Coulomb's friction law and the creep force laws, the Friction Formula and Creep Formula for the evaluation of derailment are derived, respectively. The analysis shows that the derailment coefficients of Friction Formula and Creep Formula required for derailment are increased considerably for smaller and negative yaw angles, and tend to the value of Nadal's Formula at larger wheelset yaw angles. The Creep Formula is more reasonable for the assessment of derailment. The effect of some parameters on flange climb derailment, such as wheel/rail friction coefficient, yaw angle, flange contact angle, wheel vertical load and curve radius, are investigated. Finally, a simplified formula for wheel climb derailment based on the Creep Formula is proposed.     

Study on flange climb derailment criteria of a railway wheelset

The wheel flange climb derailment, which can be usually considered as a quasi-static process, is one of the main types of derailment, and often occurs on curved tracks due to large wheel lateral force and reduced vertical force. The general formula for the wheel critical derailment coefficient Q/P, the ratio of wheel lateral force to vertical force, is derived through analysing the forces exerted on the flange climb wheel. Based on the Coulomb's friction law and the creep force laws, the Friction Formula and Creep Formula for the evaluation of derailment are derived, respectively. The analysis shows that the derailment coefficients of Friction Formula and Creep Formula required for derailment are increased considerably for smaller and negative yaw angles, and tend to the value of Nadal's Formula at larger wheelset yaw angles. The Creep Formula is more reasonable for the assessment of derailment. The effect of some parameters on flange climb derailment, such as wheel/rail friction coefficient, yaw angle, flange contact angle, wheel vertical load and curve radius, are investigated. Finally, a simplified formula for wheel climb derailment based on the Creep Formula is proposed.     

Simulation of dynamic interaction between train and railway turnout

Dynamic train–track interaction is more complex in railway turnouts (switches and crossings) than that in ordinary tangent or curved tracks. Multiple contacts between wheel and rail are common, and severe impact loads with broad frequency contents are induced, when nominal wheel–rail contact conditions are disturbed because of the continuous variation in rail profiles and the discontinuities in the crossing panel. The absence of transition curves at the entry and exit of the turnout, and the cant deficiency, leads to large wheel–rail contact forces and passenger discomfort when the train is switching into the turnout track. Two alternative multibody system (MBS) models of dynamic interaction between train and a standard turnout design are developed. The first model is derived using a commercial MBS software. The second model is based on a multibody dynamics formulation, which may account for the structural flexibility of train and track components (based on finite element models and coordinate reduction methods). The variation in rail profile is accounted for by sampling the cross-section of each rail at several positions along the turnout. Contact between the back of the wheel flange and the check rail, when the wheelset is steered through the crossing, is considered. Good agreement in results from the two models is observed when the track model is taken as rigid.     

Indirect method for wheel–rail force measurement and derailment evaluation

Wheel set flange derailment criteria for railway vehicles are derived and the influence of wheel–rail contact parameters is studied. An indirect method for wheel–rail force measurement based on these derailment evaluation criteria is proposed. Laboratory tests for the calibration of strain–force devices on the bearing box are carried out to determine the relationship between the applied force and the measured strain. The simulation package, SIMPACK, is used to develop a passenger car model to generate wheel–rail forces and vibration signals. Different cases are considered in this model to provide an accurate validation of the identified wheel–rail forces. A feasibility test is conducted in the Beijing Loop test line using a passenger car equipped with a set of strain gauges on the wheel set. The comparison of the force time history applied to the instrumented wheel set and that obtained using the indirect method is presented.     

Solution of the Multiple Wheel and Rail Contact Dynamic Problem

SUMMARY

An unconventional method for calculating the forces developing in the wheel and rail contact patches of a railway vehicle has been implemented at the New Technology Laboratory of INRETS. It takes into account the elastic deformations of the materials in the Hertzian elliptical contact areas; the possibility of having simultaneously several contact patches on each wheel, is introduced in the simulation of the dynamic phenomena.

The theory is applied for a high speed bogie running on a perfectly straight track.     

Inverse identification of wheel–rail contact forces based on observation of wheel disc strains: an evaluation of three numerical algorithms

In this paper, three numerical algorithms for the identification of wheel–rail contact forces based on measured wheel disc strains on an instrumented railway wheelset are discussed and compared. The three algorithms include one approach resting on static calibration, one that is applying a Kalman filter and the third is exploiting an inverse identification scheme. To demonstrate and evaluate the alternative methods, two load cases including periodic excitation by sinusoidal wheel–rail irregularities and transient excitation by an insulated rail joint are considered. Based on a previously presented vehicle–track interaction model in the time domain, load scenarios are defined by taking the calculated vertical wheel–rail contact forces as the reference force to be re-identified by the proposed algorithms. The reference contact forces are applied on a finite element model of the wheel to generate synthetic observation data, that is, radial strains at the positions of the strain gauges, serving as input to the identification procedures. It is concluded that the inverse identification scheme leads to superior accuracy at higher computational cost. If on-line implementation and evaluation is required, the Kalman filter generates better accuracy than the static calibration approach.     

A new method for wheel–rail contact force continuous measurement using instrumented wheelset

With the aim of improving the continuous measurement of wheel–rail contact force by instrumented wheelset, instead of solving the non-linear equations, we proposed a new method based on state space theory. With this new method, the wheel–rail contact force can be calculated by the recurrence relation and the signals from strain gauge bridges on wheel web. The implementation of continuous instrumented wheelset is quite general and simplified, due to the specific bridging scheme is not necessary. It means that continuous measurement of the contact force could be realised with a simple bridging scheme, even as simple as discrete instrumented scheme. In this work, we first demonstrated and discussed the effectiveness and accuracy of this new method by estimation results with the numerical simulations, and we also applied this new method to two field tests, including one was conducted in a loop test line using a high-speed train and the other one was conducted in an urban line with a light rail vehicle. In a word, this new method is proved to be an effective way to monitor the wheel–rail contact force of rail vehicle track system.     

Development and validation of a wear model for the analysis of the wheel profile evolution in railway vehicles

The numerical wheel wear prediction in railway applications is of great importance for different aspects, such as the safety against vehicle instability and derailment, the planning of wheelset maintenance interventions and the design of an optimal wheel profile from the wear point of view. For these reasons, this paper presents a complete model aimed at the evaluation of the wheel wear and the wheel profile evolution by means of dynamic simulations, organised in two parts which interact with each other mutually: a vehicle's dynamic model and a model for the wear estimation. The first is a 3D multibody model of a railway vehicle implemented in SIMPACK?, a commercial software for the analysis of mechanical systems, where the wheel–rail interaction is entrusted to a C/C++user routine external to SIMPACK, in which the global contact model is implemented. In this regard, the research on the contact points between the wheel and the rail is based on an innovative algorithm developed by the authors in previous works, while normal and tangential forces in the contact patches are calculated according to Hertz's theory and Kalker's global theory, respectively. Due to the numerical efficiency of the global contact model, the multibody vehicle and the contact model interact directly online during the dynamic simulations.

The second is the wear model, written in the MATLAB® environment, mainly based on an experimental relationship between the frictional power developed at the wheel–rail interface and the amount of material removed by wear. Starting from a few outputs of the multibody simulations (position of contact points, contact forces and rigid creepages), it evaluates the local variables, such as the contact pressures and local creepages, using a local contact model (Kalker's FASTSIM algorithm). These data are then passed to another subsystem which evaluates, by means of the considered experimental relationship, both the material to be removed and its distribution along the wheel profile, obtaining the correspondent worn wheel geometry.

The wheel wear evolution is reproduced by dividing the overall chosen mileage to be simulated in discrete spatial steps: at each step, the dynamic simulations are performed by means of the 3D multibody model keeping the wheel profile constant, while the wheel geometry is updated through the wear model only at the end of the discrete step. Thus, the two parts of the whole model work alternately until the completion of the whole established mileage. Clearly, the choice of an appropriate step length is one of the most important aspects of the procedure and it directly affects the result accuracy and the required computational time to complete the analysis.

The whole model has been validated using experimental data relative to tests performed with the ALn 501 ‘Minuetto’ vehicle in service on the Aosta–Pre Saint Didier track; this work has been carried out thanks to a collaboration with Trenitalia S.p.A and Rete Ferroviaria Italiana, which have provided the necessary technical data and experimental results.     

Effect of System Nonlinearities on Locomotive Bogie Hunting Stability

This paper presents the effect of system parameters on hunting of a rail vehicle with nonlinear yaw dampers and wheel-rail interface. This study is intended to complement earlier studies by True et al. where they investigated the effect of nonlinearities stemming from creep-creep force saturation and wheel/rail contact forces. The rail vehicle is represented by a two-axle truck (bogie) that includes the dynamics of the wheelsets and the truck frame. The numerical simulation results show that yaw damping can have a mixed effect on the hunting critical speed. In some ranges, increasing damping can actually lower the critical speed, unlike the results commonly obtained from a linear model. Flange contact nonlinearities can also have a significant effect on the hunting behavior. Large lateral stiffness of the rail can increase lateral force to vertical force (L/V) ratio during hunting. Increasing the gauge clearance, however, can have an opposite effect. The effect of a variety of other parameters, such as the primary suspension yaw and lateral stiffness, primary suspension lateral damping, wheelset mass, and truck frame mass, are summarized in a table.     

Experimental and numerical investigation on the derailment of a railway wheelset with solid axle

This paper presents the results of an experimental and numerical investigation on the derailment of a railway wheelset with solid axle. Tests were carried out under quasi-steady-state conditions, on a full-scale roller rig, and allowed to point out the effect of different parameters like the wheelset's angle of attack and the ratio between the vertical loads acting on the flanging and non-flanging wheels. On the basis of the test results, some existing derailment criteria are analysed in this paper and two new criteria are proposed. A model of wheel–rail contact is proposed for the mathematical modelling of the flange climb process, and numerical vs. experimental comparisons are used to obtain model validation.