基于线性路径跟踪控制的换道避撞控制策略研究

为实现车辆自主避撞,改善道路交通安全状况,提出一种基于线性路径跟踪控制的换道避撞控制策略。为实时确定制动和换道时机,获取跟车状态下自车和前车车速、加速度、相对距离以及驾驶人制动反应时间计算制动安全距离和换道安全距离,并在此基础上分别引入制动危险系数B和换道危险系数S评估制动与换道风险,使得车辆发生追尾碰撞的危险程度和主动干预阈值更直观。根据车辆期望横向加速度和期望横向位移的变化特性,采用5次多项式法规划符合驾驶人换道避撞特性的避撞路径。为保证换道避撞过程中驾驶人的安全舒适,采用最大横向加速度约束换道避撞轨迹。为实现对换道避撞路径的线性跟踪控制,保证车辆的操纵稳定性和横摆稳定性,基于车辆稳态动力学模型建立前馈控制,结合线性反馈控制消除换道路径的位置和横摆角偏差,修正参考路径实现直车道场景追尾避撞控制。仿真和实车交叉验证试验表明：根据车辆期望横向加速度和期望横向位移建立的符合驾驶人换道避撞特性的五次多项式换道路径与驾驶人实际换道避撞路径基本吻合,结合碰撞时间和车间时距的制动避撞控制策略能够在保证车辆行驶安全舒适性的同时有效避免车辆追尾碰撞,减少交通事故的发生。     

Design of rollover prevention controller with linear matrix inequality-based trajectory sensitivity minimisation

This paper presents a method to design a rollover prevention controller for vehicle systems. The vehicle rollover can be prevented by a controller that minimises the lateral acceleration and the roll angle. Rollover prevention capability can be enhanced if the controlled vehicle system is robust to the variation of the height of the centre of gravity and the speed of the vehicle. For this purpose, a robust controller is designed with linear matrix inequality-based trajectory sensitivity minimisation. Differential braking and active suspension are adopted as actuators that generate yaw and roll moments, respectively. The newly proposed method is shown to be effective in preventing rollover by the simulation on a non-linear multibody dynamic simulation software, CarSim^®.     

Active Roll Control of Articulated Vehicles

This paper describes an investigation into active roll control of articulated vehicles. The objective is to minimise lateral load transfer using anti-roll bars incorporating low bandwidth hydraulic actuators. Results from handling tests performed on an articulated vehicle are used to validate a nonlinear yaw/roll model of the vehicle. The methodology used to design lateral acceleration controllers for vehicles equipped with active anti-roll bars is developed using a simplified linear articulated vehicle model. The hardware limitations and power consumption requirements of the active elements are studied. The controller is then implemented in the validated articulated vehicle model to evaluate the performance of an articulated lorry with active anti-roll bars. The simulation results demonstrate the possibility of a significant improvement in transient roll performance of the vehicle, using a relatively low power system (10 kW), with low bandwidth actuators (5 Hz).     

Design of a rollover index-based vehicle stability control scheme

This paper presents a rollover index (RI)-based vehicle stability control (VSC) scheme. A rollover index, which indicates an impending rollover, is developed by a roll dynamics phase plane analysis. A model-based roll estimator is designed to estimate the roll angle and roll rate of the vehicle body with lateral acceleration, yaw rate, steering angle and vehicle velocity measurements. The rollover index is computed using an estimated roll angle, estimated roll rate, measured lateral acceleration and time-to-wheel lift. A differential braking control law is designed using a direct yaw control method. The VSC threshold is determined from the rollover index. The effectiveness of the RI, the performance of the estimator and the control scheme are investigated via simulations using a validated vehicle simulator. It is shown that the proposed RI can be a good measure of the danger of rollover and the proposed RI-based VSC scheme can reduce the risk of a rollover.     

An Experimental Study of a Prototype Active Anti-Roll Suspension System

Active roll control is known to offer substantial improvements in ride and handling performance over the most sophisticated passive suspension systems. However although many different active suspension systems have been discussed and analysed through simulation little information regarding experimental performance data from a prototype active roll control system has been published. This study focuses on the design, development, commissioning and experimental evaluation of a roll control suspension based on active anti-roll bar actuation. In tests, the prototype vehicle demonstrated excellent steady state and dynamic roll cancellation within the lateral acceleration range of 0.5g. Subjective assessments of the system confirmed the benefits of a level ride together with the added benefit accrued from the elimination of roll dynamics.     

A method for estimation of vehicle inertial parameters

In this paper, a new method is presented for estimating the current sprung mass inertial parameters of a vehicle, such as the mass, pitch and roll mass moments of inertia, and lateral and longitudinal centre of gravity locations. The method measures the sprung mass response when the vehicle is driven over an unknown and unmeasured random road profile. From these measurements, the equivalent free-decay responses are extracted and modal analysis techniques used to estimate the sprung mass natural frequencies, damping ratios and mode shapes. This information is combined with a simplified vehicle estimation model, least squares analysis and known equivalent stiffness parameters to estimate the vehicles’ inertial parameters. The results obtained from several simulation examples show that estimates of the inertial parameters generally have small relative errors.     

Roll Plane Analysis of Articulated Tank Vehicles During Steady Turning

The rollover immunity levels of articulated tank vehicles with partial loads are investigated. A static roll plane model of the articulated vehicle employing partially filled cylindrical tank is developed. The vertical and lateral translation of the liquid cargo due to vehicle roll angle and lateral acceleration, encountered during steady turning, are evaluated. The roll moments arising from vertical and lateral translation of the liquid cargo are determined and incorporated in the roll plane model of the vehicle. The adverse influence of the unique interactions of the liquid within the tank vehicle, on the rollover limit of the articulated vehicle is demonstrated. The influence of compartmenting of the tank on the steady turning roll response of the vehicle is analyzed, and an optimal order of unloading the compartmented tank is discussed.     

Roll Plane Analysis of Articulated Tank Vehicles During Steady Turning

SUMMARY

The rollover immunity levels of articulated tank vehicles with partial loads are investigated. A static roll plane model of the articulated vehicle employing partially filled cylindrical tank is developed. The vertical and lateral translation of the liquid cargo due to vehicle roll angle and lateral acceleration, encountered during steady turning, are evaluated. The roll moments arising from vertical and lateral translation of the liquid cargo are determined and incorporated in the roll plane model of the vehicle. The adverse influence of the unique interactions of the liquid within the tank vehicle, on the rollover limit of the articulated vehicle is demonstrated. The influence of compartmenting of the tank on the steady turning roll response of the vehicle is analyzed, and an optimal order of unloading the compartmented tank is discussed.     

Modal Controllers for Active Steering of Railway Vehicles with Solid Axle Wheelsets

This paper presents the development of a modal control strategy for the active steering of solid axle railway vehicles and reveals benefits of actively stabilising the wheelsets of a railway vehicle. A modal decomposition is applied to a 2-axle railway vehicle to de-couple its body lateral and yaw motions and hence to allow more detailed analysis of the vehicle behaviour and more robust design of active controllers. Independent controllers for the two motions are developed based on the two de-coupled modes. Parameter variations such as creep coefficients and wheelset conicity are taken into account in the design process to guarantee a robust design. The study shows that, compared to a passive vehicle, the vehicles with actively steered wheelsets not only perform much better on a curved track, but also improve the ride quality on straight track. Computer simulations are used in the study to verify the development of the controllers and assess the system performance with the control scheme proposed.     

Modal Controllers for Active Steering of Railway Vehicles with Solid Axle Wheelsets

This paper presents the development of a modal control strategy for the active steering of solid axle railway vehicles and reveals benefits of actively stabilising the wheelsets of a railway vehicle. A modal decomposition is applied to a 2-axle railway vehicle to de-couple its body lateral and yaw motions and hence to allow more detailed analysis of the vehicle behaviour and more robust design of active controllers. Independent controllers for the two motions are developed based on the two de-coupled modes. Parameter variations such as creep coefficients and wheelset conicity are taken into account in the design process to guarantee a robust design. The study shows that, compared to a passive vehicle, the vehicles with actively steered wheelsets not only perform much better on a curved track, but also improve the ride quality on straight track. Computer simulations are used in the study to verify the development of the controllers and assess the system performance with the control scheme proposed.     

A curving ACC system with coordination control of longitudinal car-following and lateral stability

The paper presents a curving adaptive cruise control (ACC) system that is coordinated with a direct yaw-moment control (DYC) system and gives consideration to both longitudinal car-following capability and lateral stability on curved roads. A model including vehicle longitudinal and lateral dynamics is built first, which is as discrete as the predictive model of the system controller. Then, a cost function is determined to reflect the contradictions between vehicle longitudinal and lateral dynamics. Meanwhile, some I/O constraints are formulated with a driver permissible longitudinal car-following range and the road adhesion condition. After that, desired longitudinal acceleration and desired yaw moment are obtained by a linear matrix inequality based robust constrained state feedback method. Finally, driver-in-the-loop tests on a driving simulator are conducted and the results show that the developed control system provides significant benefits in weakening the impact of DYC on ACC longitudinal car-following capability while also improving lateral stability.     

无人驾驶汽车路径跟踪控制方法拟人程度研究

无人驾驶汽车路径跟踪控制是无人驾驶汽车运动控制的核心所在,目前常用的路径跟踪模型主要以路径跟踪精度为主要控制目标,在很大程度上忽略了无人驾驶汽车的乘坐舒适性和控制的拟人程度。为了研究无人驾驶汽车路径跟踪控制算法的拟人程度并提高乘坐舒适性,基于转向几何学、汽车运动学和汽车动力学理论建立实车中常用的4种路径跟踪模型,提出以路径跟踪过程中的最大横向加速度a_ymax和方向盘转角平方和δ_w²共同表征路径跟踪模型的拟人程度和横向乘坐舒适性。基于驾驶人实车换道试验数据,建立多项式拟人换道参考路径,搭建CarSim/Simulink联合仿真模型,并对其进行不同车速下的车辆换道试验。研究结果表明：路径跟踪模型的横向循迹偏差均会随着车速的提高而增加,但都能较好实现路径跟踪;带预瞄路径跟踪模型和动力学前馈最优LQR路径跟踪模型拟人程度较好;汽车运动学路径跟踪模型的乘坐舒适性最差,方向盘修正激烈;在100 km·h^-1,a_ymax>0.7 m·s^-2,δ_w²>2.7×10³时,拟人程度最差;不带预瞄路径跟踪模型循迹精度最高,且拟人程度最高,乘坐舒适性最好,120 km·h^-1时,a_ymax ≤ 0.5 m·s^-2。     

Design of a feedback-feedforward steering controller for accurate path tracking and stability at the limits of handling

This paper presents a feedback-feedforward steering controller that simultaneously maintains vehicle stability at the limits of handling while minimising lateral path tracking deviation. The design begins by considering the performance of a baseline controller with a lookahead feedback scheme and a feedforward algorithm based on a nonlinear vehicle handling diagram. While this initial design exhibits desirable stability properties at the limits of handling, the steady-state path deviation increases significantly at highway speeds. Results from both linear and nonlinear analyses indicate that lateral path tracking deviations are minimised when vehicle sideslip is held tangent to the desired path at all times. Analytical results show that directly incorporating this sideslip tangency condition into the steering feedback dramatically improves lateral path tracking, but at the expense of poor closed-loop stability margins. However, incorporating the desired sideslip behaviour into the feedforward loop creates a robust steering controller capable of accurate path tracking and oversteer correction at the physical limits of tyre friction. Experimental data collected from an Audi TTS test vehicle driving at the handling limits on a full length race circuit demonstrates the improved performance of the final controller design.     

汽车的力学参数与稳态转向特性

本文以汽车力学参数试验台测出的数据为基础，为通过建立轮胎侧偏角，车厢侧倾角，回正力矩与侧向加速度之间的关系，运用最小二乘法对测试数据进行线性曲线拟合，找出了这些数据与汽车记转向特性之间的关系，并按国家标准ＧＢ／Ｔ３０４７－９１中的有关规定对被测试车辆的稳态转向特性进行了评价 。     

基于SIMULINK的汽车高速行驶姿态的影响因素分析

基于MATLAB/SIMULINK,以3自由度汽车非线性动力学模型为基础,建立仿真模型对汽车行驶姿态进行仿真研究,并且模拟了汽车在极限行驶工况下的行驶姿态,较低的行驶速度,适当增加侧倾转向系数可以提高汽车的操纵稳定性。前正/后负车轮外倾角可以保证汽车在高速转向/制动时保持一定的恢复横摆力矩,提高行驶安全性。改变侧倾阻尼系数对高速转向的操纵性影响不大而对行驶的平顺性有较大影响。     

液压互联悬架抗侧倾控制研究（双语出版）

针对车辆减少能量消耗与提高抗侧倾能力需求,提出了一种主/被动可切换的液压互联悬架抗侧倾控制方法。基于9自由度车辆动力学模型,考虑蓄能器、液压缸、液压泵三者之间耦合的体积-流量-压力特性,建立液压互联悬架主动控制时域模型;结合"车身侧倾角-车身侧倾角速度"相平面法及车辆侧向加速度,得到车辆侧倾稳定域,并提出液压互联悬架系统侧倾稳定性控制介入与退出判据;在此基础上,采用Backstepping非线性控制算法设计主动液压互联抗侧倾控制器。最后,分析并改进侧倾稳定性评价指标,通过在MATLAB/Simulink环境下进行高速双移线、鱼钩试验等极端工况数值仿真,验证所提出的液压互联悬架主/被动切换控制系统能在减少能量消耗的情况下能否提高车辆抗侧翻的能力。研究结果表明：所提出的控制系统能有效提高车辆抗侧翻能力;当车辆侧倾状态超出设定的侧倾稳定区域介入线时,液压互联悬架系统由被动模式切换为主动抗侧倾模式,控制车辆侧倾状态回到稳定区域,以提高车辆侧倾稳定性;当判定车辆侧倾状态满足主动控制退出条件时,液压互联悬架系统回到被动模式,以减小能量消耗。     

一种汽车ESP仿真模型的研究

基于Pacejka的"魔术公式"轮胎模型,建立了包括汽车纵向与横向移动、横摆、侧倾和4个车轮的转动的8自由度动力学模型.设计了由汽车仿真模型和驱动系统、四通道制动系统、制动踏板、转向盘与油门踏板等实物以及控制器(ESP)等部分组成的半实物仿真平台.以侧向加速度与横摆角速度为仿真控制变量对模型进行仿真测试.仿真与实车测试数据相当接近,为ESP的研究提供了有效的模型.     

Development of an electric active rollcontrol (ARC) algorithm for a SUV

Cornering maneuvers with reduced body roll and without loss in comfort are leading requirements for car manufacturers. An electric active roll control (ARC) system controls body roll angle with motor-driven actuators installed in the centers of the front and rear stabilizer bars. A vehicle analysis model developed using a CarSim S/W was validated using vehicle test data. Two ARC algorithms for a sports utility vehicle (SUV) were designed using a sliding-mode control algorithm based on a nonlinear roll model and an estimated lateral acceleration based on a linearized roll model. Co-simulation with the Matlab simulink controller model and the CarSim vehicle model were conducted to evaluate the performance of two ARC control algorithms. To validate the ARC performance in a real vehicle, vehicle tests were conducted at KATECH proving ground using a small SUV equipped with two ARC actuators, upper and lower controllers and a few subsystems. From the simulation and vehicle validation test results, the proposed ARC control algorithm for the developed ARC actuator prototypes improves the vehicle’s dynamic performance.     

汽车侧翻和滚翻事故建模研究

分析汽车在侧翻和滚翻过程中的受力状态和轮胎或车身与路面的相互作用方式,建立汽车侧翻和滚翻的运动学和动力学模型,揭示汽车临界侧翻碰撞力与持续作用时间等参数的关系,推导侧翻车辆侧向速度的范围,确定滚筒模型中关键参数的选取方法。事故案例表明模型在实际应用中效果良好、定量准确、直观性强。     

Vehicle dynamic estimation with road bank angle consideration for rollover detection: theoretical and experimental studies

This article describes a method of vehicle dynamics estimation for impending rollover detection. This method is evaluated via a professional vehicle dynamics software and then through experimental results using a real test vehicle equipped with an inertial measurement unit. The vehicle dynamic states are estimated in the presence of the road bank angle (as a disturbance in the vehicle model) using a robust observer. The estimated roll angle and roll rate are used to compute the rollover index which is based on the prediction of the lateral load transfer. In order to anticipate the rollover detection, a new method is proposed in order to compute the time-to-rollover using the load transfer ratio. The used nonlinear model is deduced from the vehicle lateral dynamics and is represented by a Takagi–Sugeno (TS) fuzzy model. This representation is used in order to take into account the nonlinearities of lateral cornering forces. The proposed TS observer is designed with unmeasurable premise variables in order to consider the non-availability of the slip angles measurement. Simulation results show that the proposed observer and rollover detection method exhibit good efficiency.