Front-Rear Interaction of a Pitch-Plane Truck Model

Results from a previously reported experimental study on heavy articulated vehicles show that the choice of tractor unit strongly affects the dynamic tyre forces generated by the trailer axles, but the choice of trailer unit does not strongly affect the tyre forces generated by the tractor axles. These results have implications for assessing the road-friendliness of tractor and trailer units. The objectives of the work described in this paper are to understand the dynamic interaction between the tractor and trailer unit, and to identify the conditions for which strong interaction exists. A mathematical model with two degrees of freedom is used to simulate the pitch-plane dynamics of an articulated vehicle. Three idealized vehicles are investigated and three conditions for strong dynamic interaction are identified. It is thought that these conditions are likely to exist in a large proportion of heavy trucks.     

An improvement in rollover detection of articulated vehicles using the grey system theory

A Rollover Index combined with the grey system theory, called a Grey Rollover Index (GRI), is proposed to assess the rollover threat for articulated vehicles with a tractor–semitrailer combination. This index can predict future trends of vehicle dynamics based on current vehicle motion; thus, it is suitable for vehicle-rollover detection. Two difficulties are encountered when applying the GRI for rollover detection. The first difficulty is effectively predicting the rollover threat of the vehicles, and the second difficulty is achieving a definite definition of the real rollover timing of a vehicle. The following methods are used to resolve these problems. First, a nonlinear mathematical model is constructed to accurately describe the vehicle dynamics of articulated vehicles. This model is combined with the GRI to predict rollover propensity. Finally, TruckSim^? software is used to determine the real rollover timing and facilitate the accurate supply of information to the rollover detection system through the GRI. This index is used to verify the simulation based on the common manoeuvres that cause rollover accidents to reduce the occurrence of false signals and effectively increase the efficiency of the rollover detection system.     

Enhancing roll stability of heavy vehicle by LQR active anti-roll bar control using electronic servo-valve hydraulic actuators

Rollover of heavy vehicle is an important road safety problem world-wide. Although rollovers are relatively rare events, they are usually deadly accidents when they occur. The roll stability loss is the main cause of rollover accidents in which heavy vehicles are involved. In order to improve the roll stability, most of modern heavy vehicles are equipped with passive anti-roll bars to reduce roll motion during cornering or riding on uneven roads. However these may be not sufficient to overcome critical situations. This paper introduces the active anti-roll bars made of four electronic servo-valve hydraulic actuators, which are modelled and integrated in a yaw-roll model of a single unit heavy vehicle. The control signal is the current entering the electronic servo-valve and the output is the force generated by the hydraulic actuator. The active control design is achieved solving a linear optimal control problem based on the linear quadratic regulator (LQR) approach. A comparison of several LQR controllers is provided to allow for tackling the considered multi-objective problems. Simulation results in frequency and time domains show that the use of two active anti-roll bars (front and rear axles) drastically improves the roll stability of the single unit heavy vehicle compared with the passive anti-roll bar.     

Stability and optimised H∞ control of tripped and untripped vehicle rollover

Vehicle rollover is a serious traffic accident. In order to accurately evaluate the possibility of untripped and some special tripped vehicle rollovers, and to prevent vehicle rollover under unpredictable variations of parameters and harsh driving conditions, a new rollover index and an anti-roll control strategy are proposed in this paper. Taking deflections of steering and suspension induced by the roll at the axles into consideration, a six degrees of freedom dynamic model is established, including lateral, yaw, roll, and vertical motions of sprung and unsprung masses. From the vehicle dynamics theory, a new rollover index is developed to predict vehicle rollover risk under both untripped and special tripped situations. This new rollover index is validated by Carsim simulations. In addition, an H-infinity controller with electro hydraulic brake system is optimised by genetic algorithm to improve the anti-rollover performance of the vehicle. The stability and robustness of the active rollover prevention control system are analysed by some numerical simulations. The results show that the control system can improve the critical speed of vehicle rollover obviously, and has a good robustness for variations in the number of passengers and longitude position of the centre of gravity.     

High-speed optimal steering of a tractor–semitrailer

A high-speed optimal trailer steering controller for a tractor–semitrailer is discussed. A linear model of a tractor–semitrailer with steered trailer axles is described, and an optimal trailer steering controller is introduced. A path-following controller is derived to minimise the path-tracking error in steady-state manoeuvres using active trailer steering. A roll stability controller is introduced by adding the lateral acceleration of trailer centre of gravity as another objective in the steering controller, so as to improve roll stability in transient manoeuvres. A strategy to switch between these two control modes is demonstrated. Simulation results show that the steering controller can ensure good path tracking of articulated vehicles in steady-state manoeuvres and improve roll stability significantly in transient manoeuvres, while maintaining the path-tracking deviation within an acceptable range. Tests with an experimental tractor–semitrailer equipped with a high-bandwidth active steering system validate the controller design and simulation results. The roll stability controller reduces the measured rearward amplification by 27%.     

The Steering Characteristics of Multiple Axle Bogie Systems

Legislation limits the load that may be transferred to the roadway by the axies of a commercial vehicle and this has resulted in the development of multi axle bogies for both the tractor and trailer units of articulated vehicles and at the rear of rigid vehicles, some of these bogies contain self steering or articulation steered axles

Experience shows that the tyre wear characteristics of multi axle bogies may be unsatisfactory. The paper analyses the role of such bogies in the context of vehicle handling and shows how the lateral tyre forces vary between the axles. An hypotheses relating the forces in a steady state turn to wear is given. The analysis may also be applied to the general case of vehicle handling.     

铰接车辆电涡流缓速器联合制动系统研究

提出利用联合制动系统将电涡流缓速器应用到铰接车辆上的方法。联合制动系统由拖车上的电涡流缓速器和挂车电控制动系统组成,二者在ECU控制下可以保证拖车与挂车制动力的合理分配以及对拖车及挂车的制动实施时间进行干预。采用该系统还可以减少铰接车辆行驶中某些事故的发生。     

Rollover risk prediction of heavy vehicles by reliability index and empirical modelling

This paper focuses on a combination of a reliability-based approach and an empirical modelling approach for rollover risk assessment of heavy vehicles. A reliability-based warning system is developed to alert the driver to a potential rollover before entering into a bend. The idea behind the proposed methodology is to estimate the rollover risk by the probability that the vehicle load transfer ratio (LTR) exceeds a critical threshold. Accordingly, a so-called reliability index may be used as a measure to assess the vehicle safe functioning. In the reliability method, computing the maximum of LTR requires to predict the vehicle dynamics over the bend which can be in some cases an intractable problem or time-consuming. With the aim of improving the reliability computation time, an empirical model is developed to substitute the vehicle dynamics and rollover models. This is done by using the SVM (Support Vector Machines) algorithm. The preliminary obtained results demonstrate the effectiveness of the proposed approach.     

Contour line of load transfer ratio for vehicle rollover prediction

For vehicle rollover control systems, an accurate and predictive rollover index is necessary for a precise rollover threat detection and rollover prevention. In this paper, the contour line of load transfer ratio (CL-LTR) and the CL-LTR-based vehicle rollover index (CLRI) are proposed, describing LTR threshold and LTR change rate precisely, providing an accurate prediction of vehicle rollover threat. In detail, the CL-LTR is proposed via the roll dynamics phase plane analysis, and its analytical solution of one-degree-of-freedom vehicle roll model and extension for full vehicle are derived. Moreover, the predictive CLRI is proposed and evaluated via vehicle dynamics study. The results demonstrate that vehicle rollover threat is predicted accurately based on the CLRI, which shows benefits for the vehicle rollover prediction and stability control.     

Application of observer-based fault detection in vehicle roll control

This paper describes how observer-based techniques for intelligent fault detection were applied to monitoring an active suspension control system in an experimental articulated heavy vehicle. The aim was to define a practical method for detecting faults, taking into account the nonlinearities of the vehicle. The experimental vehicle was divided conceptually into subsystems, namely the passive dynamics of the trailer, the dynamics of the hydraulic actuators, and the expected response of the closed-loop system. A linear dynamic model was designed for each subsystem. A fault detection observer was then designed for each dynamic model. The observer feedback gains were chosen to optimise estimation by the observer residual of specified errors on the output measurements. The observer residuals were then normalised and combined logically to provide a fault diagnosis. The performance of the fault detection scheme is demonstrated in the case of sensor faults and changes in the operation of the active control system.     

The Steering Characteristics of Multiple Axle Bogie Systems

SUMMARY

Legislation limits the load that may be transferred to the roadway by the axies of a commercial vehicle and this has resulted in the development of multi axle bogies for both the tractor and trailer units of articulated vehicles and at the rear of rigid vehicles, some of these bogies contain self steering or articulation steered axles

Experience shows that the tyre wear characteristics of multi axle bogies may be unsatisfactory. The paper analyses the role of such bogies in the context of vehicle handling and shows how the lateral tyre forces vary between the axles. An hypotheses relating the forces in a steady state turn to wear is given. The analysis may also be applied to the general case of vehicle handling.     

Active Roll Control of Articulated Vehicles

This paper describes an investigation into active roll control of articulated vehicles. The objective is to minimise lateral load transfer using anti-roll bars incorporating low bandwidth hydraulic actuators. Results from handling tests performed on an articulated vehicle are used to validate a nonlinear yaw/roll model of the vehicle. The methodology used to design lateral acceleration controllers for vehicles equipped with active anti-roll bars is developed using a simplified linear articulated vehicle model. The hardware limitations and power consumption requirements of the active elements are studied. The controller is then implemented in the validated articulated vehicle model to evaluate the performance of an articulated lorry with active anti-roll bars. The simulation results demonstrate the possibility of a significant improvement in transient roll performance of the vehicle, using a relatively low power system (10 kW), with low bandwidth actuators (5 Hz).     

State estimation in roll dynamics for commercial vehicles

Accurate lateral load transfer estimation plays an important role in improving the performance of the active rollover prevention system equipped in commercial vehicles. This estimation depends on the accurate prediction of roll angles for both the sprung and the unsprung subsystems. This paper proposes a novel computational method for roll-angle estimation in commercial vehicles employing sensors which are already used in a vehicle dynamic control system without additional expensive measurement units. The estimation strategy integrates two blocks. The first block contains a sliding-mode observer which is responsible for calculating the lateral tyre forces, while in the second block, the Kalman filter estimates the roll angles of the sprung mass and those of axles in the truck. The validation is conducted through MATLAB/TruckSim co-simulation. Based on the comparison between the estimated results and the simulation results from TruckSim, it can be concluded that the proposed estimation method has a promising tracking performance with low computational cost and high convergence speed. This approach enables a low-cost solution for the rollover prevention in commercial vehicles.     

Design of rollover prevention controller with linear matrix inequality-based trajectory sensitivity minimisation

This paper presents a method to design a rollover prevention controller for vehicle systems. The vehicle rollover can be prevented by a controller that minimises the lateral acceleration and the roll angle. Rollover prevention capability can be enhanced if the controlled vehicle system is robust to the variation of the height of the centre of gravity and the speed of the vehicle. For this purpose, a robust controller is designed with linear matrix inequality-based trajectory sensitivity minimisation. Differential braking and active suspension are adopted as actuators that generate yaw and roll moments, respectively. The newly proposed method is shown to be effective in preventing rollover by the simulation on a non-linear multibody dynamic simulation software, CarSim^®.     

基于制动与悬架系统的车辆主动侧翻控制的研究

为提高车辆抗侧翻能力,建立了10自由度整车侧翻动力学模型,应用车辆动力学和轮胎力耦合特性,提出了一种基于差动制动和半主动悬架协同工作的车辆主动抗侧翻控制策略。通过对制动力矩的差动调节和半主动悬架阻尼力的适时匹配,实现对车辆侧翻的有效控制。根据子系统运动特性,设计了制动系统基于滑移率的积分滑模控制器和悬架系统灰模糊控制器。分别对制动、悬架控制及综合控制进行的鱼钩试验仿真结果表明,综合控制策略可有效降低危险时域车辆的侧倾角,相对于单一系统控制进一步提高了车辆抗侧翻能力。     

A closed-loop dynamic simulation-based design method for articulated heavy vehicles with active trailer steering systems

This paper presents a closed-loop dynamic simulation-based design method for articulated heavy vehicles (AHVs) with active trailer steering (ATS) systems. AHVs have poor manoeuvrability at low speeds and exhibit low lateral stability at high speeds. From the design point of view, there exists a trade-off relationship between AHVs’ manoeuvrability and stability. For example, fewer articulation points and longer wheelbases will improve high-speed lateral stability, but they will degrade low-speed manoeuvrability. To tackle this conflicting design problem, a systematic method is proposed for the design of AHVs with ATS systems. In order to evaluate vehicle performance measures under a well-defined testing manoeuvre, a driver model is introduced and it ‘drivers’ the vehicle model to follow a prescribed route at a given speed. Considering the interactions between the mechanical trailer and the ATS system, the proposed design method simultaneously optimises the active design variables of the controllers and passive design variables of the trailer in a single design loop (SDL). Through the design optimisation of an ATS system for an AHV with a truck and a drawbar trailer combination, this SDL method is compared against a published two design loop method. The benchmark investigation shows that the former can determine better trade-off design solutions than those derived by the latter. This SDL method provides an effective approach to automatically implement the design synthesis of AHVs with ATS systems.     

Real-time multiple-model estimation of centre of gravity position in automotive vehicles

In this paper, we present a methodology based on multiple models and switching for real-time estimation of centre of gravity (CG) position in automotive vehicles. The method utilises well-known simple linear vehicle models for lateral and roll dynamics and assumes the availability of standard stock automotive sensors. We illustrate the technique with numerical simulations as well as with measured sensor data from an sport utility vehicle. We also compare our estimation results with traditional linear least-squares estimators to show the efficacy of our technique. Finally, we give a simple application example for implementing the idea in automotive vehicles as a switch for rollover controller activation.     

Design of active suspension and electronic stability program for rollover prevention

This paper presents a method for the design of a controller for rollover prevention using active suspension and an electronic stability program (ESP). Active suspension is designed with linear quadratic static output feedback control methodology to attenuate the effect of lateral acceleration on the roll angle and suspension stroke via control of the suspension stroke and tire deflection of the vehicle. However, this approach has a drawback in the loss of maneuverability because the active suspension for rollover prevention produces in vehicles an extreme over-steer characteristic. To overcome this drawback of the active suspension based method, ESP is designed. Through simulations, the proposed method is shown to be effective in preventing rollover.     

Integration of vehicle yaw stabilisation and rollover prevention through nonlinear hierarchical control allocation

This work presents an approach to rollover prevention that takes advantage of the modular structure and optimisation properties of the control allocation paradigm. It eliminates the need for a stabilising roll controller by introducing rollover prevention as a constraint on the control allocation problem. The major advantage of this approach is the control authority margin that remains with a high-level controller even during interventions for rollover prevention. In this work, the high-level control is assigned to a yaw stabilising controller. It could be replaced by any other controller. The constraint for rollover prevention could be replaced by or extended to different control objectives. This work uses differential braking for actuation. The use of additional or different actuators is possible. The developed control algorithm is computationally efficient and suitable for low-cost automotive electronic control units. The predictive design of the rollover prevention constraint does not require any sensor equipment in addition to the yaw controller. The method is validated using an industrial multi-body vehicle simulation environment.     

铰接车辆转向侧翻过程仿真

建立了铰接式车辆转向侧翻过程的数学模型,根据铰接式车辆在转向侧翻过程中的一些重要特性,研究和分析了铰接车辆侧翻的影响参数,通过过程仿真,获得了实现铰按车辆安全转向的车速临界值.