Combined control of a regenerative braking and antilock braking system for hybrid electric vehicles

Most parallel hybrid electric vehicles (HEV) employ both a hydraulic braking system and a regenerative braking system to provide enhanced braking performance and energy regeneration. A new design of a combined braking control strategy (CBCS) is presented in this paper. The design is based on a new method of HEV braking torque distribution that makes the hydraulic braking system work together with the regenerative braking system. The control system meets the requirements of a vehicle longitudinal braking performance and gets more regenerative energy charge back to the battery. In the described system, a logic threshold control strategy (LTCS) is developed to adjust the hydraulic braking torque dynamically, and a fuzzy logic control strategy (FCS) is applied to adjust the regenerative braking torque dynamically. With the control strategy, the hydraulic braking system and the regenerative braking system work synchronously to assure high regenerative efficiency and good braking performance, even on roads with a low adhesion coefficient when emergency braking is required. The proposed braking control strategy is steady and effective, as demonstrated by the experiment and the simulation.     

An integrated control strategy for the composite braking system of an electric vehicle with independently driven axles

For an electric vehicle with independently driven axles, an integrated braking control strategy was proposed to coordinate the regenerative braking and the hydraulic braking. The integrated strategy includes three modes, namely the hybrid composite mode, the parallel composite mode and the pure hydraulic mode. For the hybrid composite mode and the parallel composite mode, the coefficients of distributing the braking force between the hydraulic braking and the two motors' regenerative braking were optimised offline, and the response surfaces related to the driving state parameters were established. Meanwhile, the six-sigma method was applied to deal with the uncertainty problems for reliability. Additionally, the pure hydraulic mode is activated to ensure the braking safety and stability when the predictive failure of the response surfaces occurs. Experimental results under given braking conditions showed that the braking requirements could be well met with high braking stability and energy regeneration rate, and the reliability of the braking strategy was guaranteed on general braking conditions.     

Distributed and self-adaptive vehicle speed estimation in the composite braking case for four-wheel drive hybrid electric car

Considering the controllability and observability of the braking torques of the hub motor, Integrated Starter Generator (ISG), and hydraulic brake for four-wheel drive (4WD) hybrid electric cars, a distributed and self-adaptive vehicle speed estimation algorithm for different braking situations has been proposed by fully utilising the Electronic Stability Program (ESP) sensor signals and multiple powersource signals. Firstly, the simulation platform of a 4WD hybrid electric car was established, which integrates an electronic-hydraulic composited braking system model and its control strategy, a nonlinear seven degrees-of-freedom vehicle dynamics model, and the Burckhardt tyre model. Secondly, combining the braking torque signals with the ESP signals, self-adaptive unscented Kalman sub-filter and main-filter adaptable to the observation noise were, respectively, designed. Thirdly, the fusion rules for the sub-filters and master filter were proposed herein, and the estimation results were compared with the simulated value of a real vehicle speed. Finally, based on the hardware in-the-loop platform and by picking up the regenerative motor torque signals and wheel cylinder pressure signals, the proposed speed estimation algorithm was tested under the case of moderate braking on the highly adhesive road, and the case of Antilock Braking System (ABS) action on the slippery road, as well as the case of ABS action on the icy road. Test results show that the presented vehicle speed estimation algorithm has not only a high precision but also a strong adaptability in the composite braking case.     

Re-adhesion control for a railway single wheelset test rig based on the behaviour of the traction motor

A method for detecting wheel slip/slide and re-adhesion control of AC traction motors in railway applications is presented in this paper. This enables a better utilisation of available adhesion and could also reduce wheel wear by reducing high creep values. With this method, the wheel–rail (roller) creepage, creep force and friction coefficient can be indirectly detected and estimated by measuring the voltage, current and speed of the AC traction motor and using an extended Kalman filter. The re-adhesion controller is designed to regulate the motor torque command according to the maximum available adhesion based on the estimated results. Simulations under different friction coefficients are carried out to test the proposed method.