The Response of Active and Semi-active Suspensions to Realistic Feedback Signals

A simple vehicle model is presented incorporating passive, active, and semi-active suspensions. When the desired feedback variables are ideally available, the system response is well understood and excellent sprung mass isolation results. More often than not, the measured variables must be signal processed in some manner prior to their use in some control algorithm. This paper presents the expected response of a simple vehicle with an active and/or semi-active suspension, subject to non-ideal feedback information.     

Performance of Low-bandwidth,Semi-active Damping Concepts for Suspension Control

Abstract

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Active Suspensions Based on Fast Load Levelers

SUMMARY

A class of active suspensions is presented which provides near optimum isolation of base motion as well as zero static deflection for force disturbances using a simple type of feedback. The load leveling effect is rapid with the system stabilized using isolated mass velocity feedback both for a semi-active damper and for the load leveler. The system can be made energy conservative and fail safe since the system reverts to a reasonable passive isolator if the load leveling effect and even if the active damping effect is switched off. The system could be incorporated in automotive vehicles with some extension of the feedback control to account for several aspects of body motion.     

Optimal Performance of Variable Component Suspensions

SUMMARY

Most vehicle suspension systems use fixed passive components that offer a compromise in performance between sprung mass isolation, suspension travel, and tireroad contact force. Recently, systems with discretely adjustable dampers and air springs been added to production vehicles. Active and semi-active damping concepts for vehicle suspensions have also been studied theoretically and with physical prototypes. This paper examines the optimal performance comparisons of variable component suspensions, including active damping and full-state feedback, for “quartercar” heave models. Two and three dimensional optimizations are computed using performance indicators to find the component parameters (control gains) that provide “optimal” performance for statistically described roadway inputs. The effects of performance weighting and feedback configuration are examined. Active damping is shown to be mainly important for vehicle isolation. A passive vehicle suspension can control suspension travel and tire contact force nearly as well as a full state feedback control strategy.     

Adaptive Suspension Concepts for Road Vehicles

SUMMARY

Most vehicle suspensions are composed of passive spring and damper devices, although improved suspension performance is possible if an active system is used to control forces or relative velocities. The complexity, power requirements, and cost of fully active suspensions have restricted their use. Various partially active suspensions have been proposed and suspensions with slow load levelers and variable dampers are in widespread use. Here we analyze a class of basically passive suspensions the parameters of which can be varied actively in response to various measured signals on the vehicle. These suspensions can come close to optimal performance with simpler means than many of the active or semi-active schemes previously proposed.     

Semi-Active Control of Wheel Hop in Ground Vehicles

ABSTRACT

A two degree-of-freedom vehicle model is developed which incorporates passive, active, and semi-active secondary suspensions. The model is used to demonstrate the trade-offs which are inherent in attempting to provide desirable sprung weight isolation while at the same time controlling unsprung weight motions.

A linear model is used first in order to compare passive and active suspensions in an analytically understandable configuration. The semi-active suspension is inherently nonlinear and is compared to the others through computer simulation. The passive suspension is, of course, the most restrictive in providing simultaneous isolation of sprung and unsprung weight; however, the active suspension is also compromised in providing both functions. The semi-active suspension does an excellent job of tracking its active counterpart.     

Performance of Low-bandwidth, Semi-active Damping Concepts for Suspension Control

Active damping has been shown to offer increased suspension performance in terms of vehicle isolation, suspension packaging, and road-tire contact force. It can even approximate the performance of full state feedback control without requiring the difficult measurement of tire deflection. Many semi-active damping strategies have been introduced to approximate the response of active damping with the modulation of passive damping parameters. These strategies have typically required a relatively high bandwidth for actuator response. This paper investigates the simulation performance and “frequency response” of two concepts in low-bandwidth semi-active suspension control, one that sets a damping force directly and another that sets the damping resistance. The electronically controlled bandwidth of these actuators is approximately an order of magnitude less than other semi-active devices; high frequency control is handled mechanically. A quarter-car model is studied with the controlled damping replacing both passive and active damping of typical control schemes. Both low-bandwidth damping strategies perform remarkably well compared to both active and high-bandwidth, semi-active damping. In certain dynamic performances, the new semi-active strategies outperform active damping and what the author calls “nominal” semi-active damping.     

Semi-Active Attitude and Vibration Control

SUMMARY

The paper discusses the attitude and vibration control of a passenger car on the basis of a full vehicle model. The analysis presented consists of two parts: (I) The introduction of a newly developed semi-active anti-roll/pitch system, (ii) An example of an actively suspended full vehicle model using a simple control strategy to improve ride comfort. The attitude control using semi-actively generated compensation forces prevents the car from rolling in curves and pitching during braking or accelerating. The strength of the system is the small energy consumption. The performance of the combination of both attitude and vibration control can compete with a fully active suspension system.     

Semi-Active Suspension with Preview Using a Frequency-Shaped Performance Index

SUMMARY

The objective of this study is to develop a control law for a semi-active suspension for the purpose of ride quality improvement. The semi-active control law is determined by reproducing the control force of an optimally controlled active suspension while suppressing its damping coefficient variation. The performance index of the optimal control for the active suspension is modified to include frequency-shaping by use of Parseval's theorem, which allows us to de-emphasize the effects of particular variables over specific frequency bands.

Through the numerical simulations, it was found that the semi-active suspension may reduce the vertical acceleration of the driver's seat and the sprung mass motions significantly. The road-holding and tire deflections were not affected much.     

Preview suspension control for a full tracked vehicle

In this study, preview control algorithms for the active and semi-active suspension systems of a full tracked vehicle (FTV) are designed based on a 3-D.O.F model and evaluated. The main issue of this study is to make the ride comfort characteristics of a fast moving tracked vehicle better to keep an operator’s driving capability. Since road wheels almost trace the profiles of the road surface as long as the track doesn’t depart from the ground, the preview information can be obtained by measuring only the absolute position or velocity of the first road wheel. Simulation results show that the performance of the sky-hook suspension system almost follows that of full state feedback suspension system and the on-off semi-active system carries out remarkable performance with the combination of 12 on-off semi-active suspension units. The results simulated with 1^st and 2^nd weighting sets mean that the suspension system combined with the soft type of inner suspension and hard type of outer suspension can carry out better ride comfort characteristics than that with identical suspensions. The full tracked vehicle (FTV) system is uncontrollable and the system is split into controllable and uncontrollable subspace using singular value decomposition transformation. Frequency response curves to four types of inputs, such as heaving, pitching, rolling, and warping inputs, also demonstrate the merits of preview control in ride comfort. All the frequency characteristic responses confirm the continuous time results.     

Theoretical Limitations in Active Vehicle Suspensions

SUMMARY

Vehicle suspensions in which forces are generated in response to feedback signals by active elements obviously offer increased design flexibility compared to conventional suspensions using passive elements such as springs and dampers. It is often assumed that if practical difficulties are neglected, active systems could in principle produce arbitrary ideal, behavior. It is shown, using a simple linear two degree-of-freedom suspension system, model that even using complete state feed back and in the case of in which the system is controllable in the control theory sense, there still are limitations to suspension performance in the fully active case. If the ideal suspension performance is defined based on low-pass filtering of roadway unevenness inputs, an active suspension may not offer much better performance than a partially active or adaptive passive suspension depending upon the values of certain vehicle parameters.     

基于微分几何理论的汽车半主动悬架非线性振动控制

针对汽车悬架系统的非线性特性,采用1／4汽车二自由度悬架模型分析半主动悬架控制。应用微分几何理论得到输出-干扰解耦方法,再经适当的坐标变换将该模型由非线性系统简化成一线性系统,并对此系统进行最优控制,然后通过非线性状态反馈实现对原系统的半主动控制。与被动悬架的仿真结果进行了比较,表明这种针对具有非线性特征的半主动悬架的非线性控制方法是可行的。通过功率谱分析,控制后系统的能量比被动悬架更趋于平均,悬架动态性能更稳定。     

The Chatter of Semi-Active On-Off Suspensions and its Cure

ABSTRACT

Semi-active suspensions are those in which otherwise passively generated damper forces are modulated using feedback control and small amounts of control effort. Recently it was discovered that two-stage, ON-OFF, semi-active control would chatter between the ON and OFF states in a manner similar to bang-bang, active control systems. This chatter is dependent upon the switching algorithm. This paper describes the dynamics of this chatter and suggests alternative control policies for its cure.     

Suboptimal Control Design of Active and Passive Suspensions Based on a Full Car Model

An optimal control design method is introduced and then applied to the optimum design of active and passive suspension systems. A basic three-dimensional 7-DOF car riding model subjected to four correlated random road inputs is considered. The design method is basically developed to allow arbitrary choice of sensors for various car state variables to be used for feedback control of each suspension unit. Previous studies show that full-state control laws and even some limited-state control laws often include feedback gains which are almost zero. Some other gains, although not zero, don't play an important role in improving the system performance measures. With the method proposed in this work, every suspension unit can have its own feedback measurements and the criterion function can be related to all state and control variables. Thus a large number of active and semi-active suspension systems with full- or limited-state control laws based on different measurement combination can be suggested, studied, and compared with each other. Instead of comparing these optimized active and semi-active suspension systems with a basic, passive suspension, the passive system itself is optimized with the same criterion. Simulations in the time domain and frequency analyses are performed, and comparisons are made among the systems in terms of r.m.s. car response measures and ISO riding comfort criterion.     

Active Damping in Road Vehicle Suspension Systems

Low order, linearized dynamic models of road vehicle suspension systems are analyzed to provide insight into the benefits of suspensions incorporating generalized velocity feedback compared with conventional passive suspensions. Damping forces from passive dampers are supplemented by forces generated by an active element requiring a power supply. A simple criterion is developed which indicates whether or not the introduction of activedamping forces will result in significant benefit for pneumatic tired vehicles.

An extended active suspension concept involving a high-gain load leveler as well as active damping is analyzed. The realization of active or semi-active damping forces through electrical or hydraulic means is briefly discussed.     

Comparison of the properties of active and semiactive suspension

In this article, the properties of active and semi-active suspension for heavy goods vehicles are compared. The criteria for the comparison are the RMS sprung mass vertical acceleration, RMS dynamic tyre force, and suspension power consumption. The active system is based on an air-spring with controlled in-flow and out-flow of the air. In the semi-active system, a controlled hydraulic damper is employed. The results concerning the semi-active suspension system were taken from the article by Besinger et al. [Besinger, F.H., Cebon, D. and Cole, D.J., 1995, Force control of a semi-active damper. Vehicle System Dynamics, 24(9), 695–723.].     

Observer Design for Electronic Suspension Applications*

SUMMARY

This paper proposes a new methodology for designing observers for automotive suspensions. Automotive suspensions are disturbance-affected dynamic systems. Semi-active suspensions are bilinear while active suspensions with hydraulic actuators are nonlinear. The proposed methodology guarantees exponentially convergent state estimation for both these systems. It uses easily accessible and inexpensive measurements. The fact that sprung mass absolute velocity of the suspension cannot be estimated in an exponentially stable manner with such measurements is also demonstrated.

Controllers using estimated states are implemented experimentally on the Berkeley Active Suspension Test Rig. Experimental results for two cases are presented : use of observer states to improve ride quality in an active suspension and use of observer states to reduce dynamic tire loading in a semi-active heavy vehicle suspension.     

The Development and Implementation of Adaptive Semi-Active Suspension Control*

SUMMARY

Using adjustable shock absorbers within vehicle suspension systems, it is possible to improve ride comfort significantly when a control strategy is applied based on the so-called skyhook principle. However, the drawback is a poorly damped wheel-hop mode which makes the road holding ability worse. Using adaptive semi-active suspension control based on the tire load variations as introduced in this paper, the trade-off between road holding and ride comfort can be relaxed. Implementation of adaptive skyhook control requires the determination of a number of important and difficult to measure states of the vehicle. This can either be accomplished by several sensors and filters or by a state estimator in combination with less sensors and an internal model of the vehicle. Both methods are discussed. Finally some preliminary test results are discussed.     

Semi-active suspension systems for railway vehicles using magnetorheological dampers. Part I: system integration and modelling

In this paper, it is aimed to investigate semi-active suspension systems using magnetorheological (MR) fluid dampers for improving the ride quality of railway vehicles. A 17-degree-of-freedom (DOF) model of a full-scale railway vehicle integrated with the semi-active controlled MR fluid dampers in its secondary suspension system is proposed to cope with the lateral, yaw, and roll motions of the car body, trucks, and wheelsets. The governing equations combining the dynamics of the railway vehicle integrated with MR dampers in the suspension system and the dynamics of the rail track irregularities are developed and a linear quadratic Gaussian (LQG) control law using the acceleration feedback is adopted, in which the state variables are estimated from the measurable accelerations with a Kalman estimator. In order to evaluate the performances of the semi-active suspension systems based on MR dampers for railway vehicles, the random and periodical track irregularities are modelled with a uniform state-space formulation according to the testing data and incorporated into the governing equation of the railway vehicle integrated with the semi-active suspension system. Utilising the governing equations and the semi-active controller developed in this paper, the simulation and analysis are presented in Part II of this paper.     

I. Minutes of the IAVSD Board Meetings

SUMMARY

A theoretical analysis is presented to model a hydromechanical, semi-active suspension system, first as a single wheel station and then as fitted to each wheel of an off-road vehicle. Predicted results show that two benefits are obtained by comparison with the equivalent passive system. First, vehicle attitude is controlled for changes in body forces arising from static loads or braking/cornering inputs. Second, a significant improvement in ride comfort is obtained because low suspension stiffnesses can be used.