Loss of stability of a railway wheel-set,subcritical or supercritical

Most researches on railway vehicle stability analysis are focused on the codimension 1 (for short, codim 1) bifurcations like subcritical and supercritical Hopf bifurcation. The analysis of codim 1 bifurcation can be completed based on one bifurcation parameter. However, two bifurcation parameters should be considered to give a general view of the motion of the system when it undergoes a degenerate Hopf bifurcation. This kind of bifurcation named the generalised Hopf bifurcation belongs to the codimension 2 (for short, codim 2) bifurcations where two bifurcation parameters need to be taken into consideration. In this paper, we give a numerical analysis of the codim 2 bifurcations of a nonlinear railway wheel-set with the QR algorithm to calculate the eigenvalues of the linearised system incorporating the Golden Cut method and the shooting method to calculate the limit cycles around the Hopf bifurcation points. Here, we found the existence of a generalised Hopf bifurcation where a subcritical Hopf bifurcation turns into a supercritical one with the increase of the bifurcation parameters, which belong to the codim 2 bifurcations, in a nonlinear railway wheel-set model. Only the nonlinear wheel/rail interactive relationship has been taken into consideration in the lateral model that is formulated in this paper. The motion of the wheel-set has been investigated when the bifurcation parameters are perturbed in the neighbourhood of their critical parameters, and the influences of different parameters on critical values of the bifurcation parameters are also given. From the results, it can be seen that the bifurcation types of the wheel-set will change with a variation of the bifurcation parameters in the neighbourhood of their critical values.     

A combined use of phase plane and handling diagram method to study the influence of tyre and vehicle characteristics on stability

This paper deals with in-curve vehicle lateral behaviour and is aimed to find out which vehicle physical characteristics affect significantly its stability. Two different analytical methods, one numerical (phase plane) and the other graphical (handling diagram) are discussed. The numerical model refers to the complete quadricycle, while the graphical one refers to a bicycle model. Both models take into account lateral load transfers and nonlinear Pacejka tyre–road interactions. The influence of centre of mass longitudinal position, tyre cornering stiffness and front/rear roll stiffness ratio on vehicle stability are analysed. The presented results are in good agreement with theoretical expectations about the above parameters influence, and show how some physical characteristics behave as saddle-node bifurcation parameters.     

Straight-ahead running of road vehicles – analytical formulae including full tyre characteristics

ABSTRACT

During straight-ahead running, the longitudinal axis of road vehicles, notably cars, is not parallel to road axis. This occurrence is general and is due both to road cross slope (road banking) and to tyre characteristics, particularly ply-steer and conicity. In order to describe such a phenomenon, the paper develops a new and relatively simple analytical model. Despite the model is linear, the solution which is provided is exact, since straight-ahead motion occurs with small angles and both the elastokinematics of suspension system and tyre characteristics can be modelled by linearised equations. The Handling Diagram theory is updated and completed by introducing the actual shifts of tyre characteristics. The validation of the analytical expressions is performed by using a MSC Adams^TM full model of a car. A subjective-objective experimental test campaign provides preliminary substantiation of the ability of the derived formulae to describe tyre performance. By means of the unreferenced analytical formulae developed in the paper, we allow, given the vehicle, the proper tyre design specification and vice-versa. In particular, a formula is given to make null the steering torque during straight-ahead driving. The derived analytical formulae may provide a sound understanding of the straight-ahead running of road vehicles.     

轮胎垂直振动动力学模型

本文提出一种自适应轮膜模型参数的简易测定方法，给出轮胎垂直振动动力学方程及相应的求解方法，并进行计算分析与试验测定。将分析结果与通常的点接触式模型相比较，对点接触式模型及本文所建立的自适应模型做了综合评价，结果表明，本模型的计算结果是令人满意的。     

Analysis of bifurcation and stability for a tractor semi-trailer in planar motion

This paper is intended for bifurcation analysis of a nonlinear tractor semi-trailer vehicle model in planar motion and for investigating its stability under constant running conditions. Bifurcation analysis shows that bifurcation diagrams of a tractor semi-trailer are quite different from those of a single-unit vehicle. Some instability phenomena of the vehicle system such as jackknifing, sideslip, and spinning are explained by correlating them with the behaviour in the neighbourhood of unstable fixed points based on analysis of eigenvectors, phase trajectories, and status of lateral tyre force saturation. It is also found that yaw planar instability of a tractor semi-trailer is caused by lateral tyre force saturation of the tractor's rear axles and/or the trailer's axles. Moreover, the stability region in the state space is demarcated, and a stability index for evaluating size of the stability region in a feasible domain is proposed. Yaw stability under constant driving conditions is analysed by using the proposed stability index.     

A study of the relationship between Magic Formula coefficients and tyre design attributes through finite element analysis

Pacejka's Magic Formula Tyre Model is widely used to represent force and moment characteristics in vehicle simulation studies meant to improve handling behaviour during steady-state cornering. The experimental technique required to determine this tyre model parameters is fairly involved and highly sophisticated. Also, total test facilities are not available in most countries. As force and moment characteristics are affected by tyre design attributes and tread patterns, manufacturing of separate tyres for each design alternative affects tyre development cycle time and economics significantly. The objective of this work is to identify the interactions among various tyre design attributes-cum-operating conditions and the Magic Formula coefficients. This objective is achieved by eliminating actual prototyping of tyres for various design alternatives as well as total experimentation on each tyre through simulation using finite element analysis. Mixed Lagrangian–Eulerian finite element technique, a specialized technique in ABAQUS, is used to simulate the steady-state cornering behaviour; it is also efficient and cost-effective. Predicted force and moment characteristics are represented as Magic Formula Tyre Model parameters through non-linear least-squares fit using MATLAB. Issues involved in the Magic Formula Tyre Model representation are also discussed. A detailed analysis is made to understand the influence of various design attributes and operating conditions on the Magic Formula parameters. Tread pattern, tread material properties, belt angle, inflation pressure, frictional behaviour at the tyre–road contact interface and their interactions are found to significantly influence vehicle-handling characteristics.     

Analysis of lateral tyre friction dynamics1

The tyre friction model is a key part of the overall multi-body tyre dynamics model. The LuGre dynamic tyre friction model is analytically linearised for pure cornering conditions. The linearised model parameters are conveniently expressed as functions of static curve slope parameters. The linearised lateral force and self-aligning torque submodels are described by equivalent mechanical systems. The linearised model and equivalent system parameters are analysed for different slip angle and wheel centre speed operating points. An example of the application of linearised tyre friction model to tyre vibration analysis is presented as well.     

The Influence of In-Plane Tyre Dynamics on ABS Braking of a Quarter Vehicle Model

For efficient analysis it is important to choose the proper model that fits the problem that needs to be solved. This paper discusses three pragmatic simulation models for longitudinal behaviour of a passenger car tyre (Steady State, Transient and Rigid Ring) that may be used in e.g. an ABS simulation. The characteristics of the simulation models are evaluated using some simple simulations. Simulations with a quarter vehicle model that includes load transfer effects are carried out to determine the deviation in results between the mentioned tyre models for an ABS application. The results show that the Steady State model may only be used below 10 Hz and that the Transient model is valid up to about 30 Hz. The results from the ABS simulation with the Rigid Ring model are most reliable and are clearly different from the Steady State and Transient model, which indicates that ABS simulations should be carried out with the Rigid Ring model. Additionally it is demonstrated that for tyre behaviour on uneven roads the influence of the tyre belt cannot be neglected.     

The Influence of In-Plane Tyre Dynamics on ABS Braking of a Quarter Vehicle Model

For efficient analysis it is important to choose the proper model that fits the problem that needs to be solved. This paper discusses three pragmatic simulation models for longitudinal behaviour of a passenger car tyre (Steady State, Transient and Rigid Ring) that may be used in e.g. an ABS simulation. The characteristics of the simulation models are evaluated using some simple simulations. Simulations with a quarter vehicle model that includes load transfer effects are carried out to determine the deviation in results between the mentioned tyre models for an ABS application. The results show that the Steady State model may only be used below 10 Hz and that the Transient model is valid up to about 30 Hz. The results from the ABS simulation with the Rigid Ring model are most reliable and are clearly different from the Steady State and Transient model, which indicates that ABS simulations should be carried out with the Rigid Ring model. Additionally it is demonstrated that for tyre behaviour on uneven roads the influence of the tyre belt cannot be neglected.     

String tyre model for evaluating steering agility performance using tyre cornering force and lateral static characteristics

The cornering force and lateral static characteristics of a tyre are fundamental factors that describe the steering feel for handling performance. However, it is difficult to justify the contribution of each factor when the tyre’s cornering motion is evaluated through subjective assessment. Currently, the relaxation length of Pacejka’s tyre model is close to describing these tyre motions. Therefore, this paper proposes a string tyre model based on the relaxation length in order to represent the steering performance. The proposed method provides a more accurate modelling of the steering agility performance. Therefore, it is possible to use this model to predict the steering response performance, and this is validated through comparison with a real relaxation length.     

Study of the Pneumatic Tyre Behaviour on Dry and Rigid Road by Finite Element Method

The paper presents a physical tyre model capable of describing the complete pneumatic tyre behaviour during steady and transient states. Given the radial deflection, the longitudinal and lateral slip, the camber angle, the inner pressure and the mechanical parameters describing the tyre structure, the model returns the vertical load, the longitudinal and lateral forces, the self aligning torque. Particular attention has been devoted to the computation (by f.e.m.) of tyre carcass and tread deformations; it is explained how side force increases by moderate braking at constant slip angle. An experimental verification validates the model, although more studies could be needed to improve model effectiveness.     

Study of the Pneumatic Tyre Behaviour on Dry and Rigid Road by Finite Element Method

SUMMARY

The paper presents a physical tyre model capable of describing the complete pneumatic tyre behaviour during steady and transient states. Given the radial deflection, the longitudinal and lateral slip, the camber angle, the inner pressure and the mechanical parameters describing the tyre structure, the model returns the vertical load, the longitudinal and lateral forces, the self aligning torque. Particular attention has been devoted to the computation (by f.e.m.) of tyre carcass and tread deformations; it is explained how side force increases by moderate braking at constant slip angle. An experimental verification validates the model, although more studies could be needed to improve model effectiveness.     

The IMMa optimisation algorithm without control input parameters

The IMMa optimisation algorithm (IOA) consists of a heuristic method based on a differential evolution algorithm for choosing the Magic Formula (MF) tyre model parameters. In a previous paper, we demonstrated that the IOA improved the searching procedure of optimum MF parameters with respect to the starting value optimisation (SVO) methods. But we had to introduce some control input parameters that were fixed during the running process. Now, the new version does not require control input variables to be chosen by the user. That is, we use an algorithm with self-adapting control parameters and it continues being easy to use, robust and fast. Hence, users do not need any kind of knowledge to use the IOA.     

A real-time approach to robust identification of tyre–road friction characteristics on mixed-μ roads

ABSTRACT

The interaction between the tyre and the road is crucial for understanding the dynamic behaviour of a vehicle. The road–tyre friction characteristics play a key role in the design of braking, traction and stability control systems. Thus, in order to have a good performance of vehicle dynamic stability control, real-time estimation of the tyre–road friction coefficient is required. This paper presents a new development of an on-line tyre–road friction parameters estimation methodology and its implementation using both LuGre and Burckhardt tyre–road friction models. The proposed method provides the capability to observe the tyre–road friction coefficient directly using measurable signals in real-time. In the first step of our approach, the recursive least squares is employed to identify the linear parameterisation form of the Burckhardt model. The identified parameters provide, through a T–S fuzzy system, the initial values for the LuGre model. Then, a new LuGre model-based nonlinear least squares parameter estimation algorithm using the proposed static form of the LuGre to obtain the parameters of LuGre model based on recursive nonlinear optimisation of the curve fitting errors is presented. The effectiveness and performance of the algorithm are demonstrated through the real-time model simulations with different longitudinal speeds and different kinds of tyres on various road surface conditions in both Matlab/Carsim environments as well as collected data from real experiments on a commercial trailer.     

The effect of the inflation pressure of tyres on motorcycle weave stability: experiments and simulation

Increasing the stability of a motorcycle requires an understanding of the optimal conditions of the tyre. The inflation pressure is one of the main parameters that directly affects the tyre properties, which in turn influences motorcycle stability and safety. This paper focuses on the effect of the inflation pressure of the tested tyres on motorcycle weave stability. Experimental data are collected from tests carried out in straight running at constant speed. The data analysis is based on stochastic subspace identification methods. Simulations are performed using an advanced motorcycle multi-body code with parameters measured from the tested vehicle. Finally, the comparison between simulations and experimental tests is discussed. The research results show an agreement between experimental tests and simulations where weave stability increases with inflation pressure for the specified range of tyre pressure.     

Geometric-based tyre vertical force estimation and stiffness parameterisation for automotive and unmanned vehicle applications

Advanced empirical, and physical-based tyre models have proven to be accurate for simulating tyre dynamics; however, these tyre models typically require expensive and intensive tyre parameterisation. Recent research into wheeled unmanned ground vehicles requiring vertical force analysis has shown good results using a simple linear spring model for the tyre which demonstrate the continued use for simple tyre models; however, parameterisation of the tyre still remains a challenge when load test equipment is not available. This paper presents a cost-effective tyre vertical stiffness parameterisation procedure using only measured tyre geometry and air pressure for applications where high-fidelity tyre models are unnecessary. Vertical forces calculated through an air volume optimisation approach are used to estimate tyre vertical stiffness. Nine tyres from the literature are compared to evaluate the performance of the vertical force estimation and stiffness parameterisation algorithms. Experimental results on a pair of ATV tyres are also presented.     

Common underlying steering curves for motorcycles in steady turns

We study the steady turn behaviours of some light motorcycle models on circular paths, using the commercial software package ADAMS-Motorcycle. Steering torque and steering angle are obtained for several path radii and a range of steady forward speeds. For path radii much greater than motorcycle wheelbase, and for all motorcycle parameters including tyre parameters held fixed, dimensional analysis can predict the asymptotic behaviour of steering torque and angle. In particular, steering torque is a function purely of lateral acceleration plus another such function divided by path radius. Of these, the first function is numerically determined, while the second is approximated by an analytically determined constant. Similarly, the steering angle is a function purely of lateral acceleration, plus another such function divided by path radius. Of these, the first is determined numerically while the second is determined analytically. Both predictions are verified through ADAMS simulations for various tyre and geometric parameters. In summary, steady circular motions of a given motorcycle with given tyre parameters can be approximately characterised by just one curve for steering torque and one for steering angle.     

汽车子午线轮胎的振动与故障诊断

子午线轮胎的主要特征是，其帘布层中的帘线是呈线纬方向布置的，由于其结构上的原因，在运行过程中很容易造成帘线带层的偏心分布不均匀的现象，因此易造成轮胎的不均匀性，结合实例阐述了轮胎的振动与故障诊断，即捷达轿车的异响是一种中频振动，奥迪轿车的异响是一种高频振动等。     

A comprehensive study on the stability analysis of vehicle dynamics with pure/combined-slip tyre models

In this paper, a vehicle's lateral dynamic model is developed based on the pure and the combined-slip LuGre tyre models. Conventional vehicle's lateral dynamic methods derive handling models utilising linear tyres and pure-slip assumptions. The current article proposes a general lateral dynamic model, which takes the linear and nonlinear behaviours of the tyre into account using the pure and combined-slip assumptions separately. The developed methodology also incorporates various normal loads at each corner and provides a proper tyre–vehicle platform for control and estimation applications. Steady-state and transient LuGre models are also used in the model development and their responses are compared in different driving scenarios. Considering the fact that the vehicle dynamics is time-varying, the stability of the suggested time-varying model is investigated using an affine quadratic stability approach, and a novel approach to define the critical longitudinal speed is suggested and compared with that of conventional lateral stability methods. Simulations have been conducted and the results are used to validate the proposed method.