Efficiency analysis of a multiple axle vehicle with hydrostatic transmission overcoming obstacles

Transmission configurations in off-road vehicles with multiple driven axles can be a determining factor in the obstacle surmounting capacity and also in the vehicle efficiency. An off-road articulated vehicle with four driven axles, four bogies and two modules has been considered for the global hydrostatic transmission efficiency analysis and for the vehicle functional efficiency analysis. The power flow through the transmission system has been quantified from the combustion engine shaft to each axle of the wheels. It has been done for different the operating conditions and taking into account the wheel–terrain interaction and the transmission configuration, that could lead to a forced slippage of some of the wheels. Results show the influence of the different wheels’ requirements, the transmission configuration limitations and the considered control strategy on the global transmission and vehicle functional efficiencies.     

Efficiency sensitivity analysis of a hydrostatic transmission for an off-road multiple axle vehicle

There is a large variety of multiple driven axle vehicles. Some of the most common are the 3-axle rigid vehicles and the 4-axle articulated vehicles, which can in some cases have different steering mechanisms, adaptive suspension, etc. This last kind of vehicles usually have very complex transmission configurations. Moreover, the required torques in each of the wheels can be very different, especially when the vehicle is working in rough terrains. The aim of this work is to study and model the driveline of this kind of vehicles, when using a hydrostatic transmission, from the performance and efficiency point of view, by analysing the influence of the operating conditions in the transmission efficiency. A global model is used to quantify the power flow in each of the transmission elements and the overall performance of the entire vehicle driveline, given the operating conditions thereof. A sensitivity analysis has also been done showing the influence of vehicle speed, rolling resistance, terrain slope and hydraulic motors displacement in the overall transmission efficiency. The interest of this work is also to make a contribution to the literature in the field of global modelling of drivelines under variable operating conditions and its application to ATVs. One important aspect is the influence of different actuation requirements that occur in different wheels at the same time. The results show that the overall performance of the transmission is highly dependent on operating conditions, on the selected transmission configuration and on the used components.     

Dynamic Behaviour of Ore Wagons in Curves at Malmbanan

SUMMARY

The transportation of ore can be made more cost efficient by use of bigger and heavier trains. An increase in axle load is thereby wanted. The fleet of ore wagons of today at Malmbanan/Ofotbanan in northern Sweden and Norway has to be updated. It is of interest to find out if it is possible to allow a higher axle load on the track with new wagons

To be able to understand and predict the effects on track wear depending on what type of vehicle that is in use, the contact forces between wheels and rails have to be determined. A computer aided analysis has been made of the dynamic behaviour of three test vehicles equipped with different types of three-piece bogies running at Malmbanan. The vehicles are modelled and their interaction with the track is analysed using the multibody simulation package GENSYS

The simulations show that, even if the axle load is increased from 25 tons to 30 tons and the velocity is increased from 50 km/h to 60 km/h, it is possible to reduce lateral track forces and wear in curves by using a different bogie than the standard three-piece bogie used today.     

A New Method for Accurately Estimating the Weight of Moving Vehicles Using Piezoelectric Sensors and Adaptive-footprint Tire Model

Summary This paper presents new methods for estimating the axle weight of a moving vehicle, using two piezoelectric sensors and adaptive-footprint tire model. It is more difficult to weigh vehicles in motion accurately than to weigh standing vehicles. The difficulties in weighing moving vehicles result from sensor limitations as well as dynamic loading effects induced by vehicle/pavement interactions. For example, two identical vehicles with the same weight will generate sensor signals that differ in the shape and the peak value, depending the tire pressure, vehicle speed, road roughness, and sensor characteristics. This paper develops a method that is much less sensitive to these variable factors in determining the axle weight of a moving vehicle. In the developed method, first the piezoelectric sensor signal is reconstructed using the inverse dynamics of a high-pass filter representing the piezoelectric sensor. Then, the reconstructed signal, is normalized, using the nominal road/tire contact length obtained using an adaptive-footprint tire model, and then integrated. Experiments are performed with 3 vehicles of known weight ranging from 1,400 kg to 28,040 kg. The developed method is compared to two other algorithms. Results show that the developed method is most consistent and accurate.     

A New Method for Accurately Estimating the Weight of Moving Vehicles Using Piezoelectric Sensors and Adaptive-footprint Tire Model

Summary This paper presents new methods for estimating the axle weight of a moving vehicle, using two piezoelectric sensors and adaptive-footprint tire model. It is more difficult to weigh vehicles in motion accurately than to weigh standing vehicles. The difficulties in weighing moving vehicles result from sensor limitations as well as dynamic loading effects induced by vehicle/pavement interactions. For example, two identical vehicles with the same weight will generate sensor signals that differ in the shape and the peak value, depending the tire pressure, vehicle speed, road roughness, and sensor characteristics. This paper develops a method that is much less sensitive to these variable factors in determining the axle weight of a moving vehicle. In the developed method, first the piezoelectric sensor signal is reconstructed using the inverse dynamics of a high-pass filter representing the piezoelectric sensor. Then, the reconstructed signal, is normalized, using the nominal road/tire contact length obtained using an adaptive-footprint tire model, and then integrated. Experiments are performed with 3 vehicles of known weight ranging from 1,400 kg to 28,040 kg. The developed method is compared to two other algorithms. Results show that the developed method is most consistent and accurate.     

Performance of spade-less wheeled military vehicles with passive and semi-active suspensions during mortar firing

Many armies are replacing heavy slow tracked vehicles with their lighter wheeled counterparts for their high mobility and better shoot and scoot capabilities. These features make the vehicle hard to track and target in counter-battery fire. However, when firing high calibre guns, spades are needed to connect the vehicle chassis to the ground, so as to transmit parts of the large firing force directly to the ground. Use of spades hinders the vehicle mobility, while elimination of them paves the way for having quicker and more mobile wheeled vehicles. In this article, vibration response of a spade-less High Mobility Multi-purpose Wheeled Vehicle with a mounted mortar is studied and controlled using stock passive, optimised passive, and optimised semi-active dampers as primary suspensions. The spade-less vehicle with optimised passive and semi-active dampers has a better response in heave, pitch, and fore-aft motions and can fire with better accuracy compared to a spade-less vehicle with stock passive dampers. Simulation results indicate that the spades can be removed from wheeled military vehicles if the precautions are taken for the tyres.     

A Tractor Handling Study

SUMMARY

Agricultural tractors are relatively slow moving vehicles but a good steer response under all working conditions is generally required. This paper evaluates the effect of ground slope, axle load, ground speed, tyres and ground surface on yaw rate response to steer input.     

Rail Vehicles' Riding Quality and Comfort Related to Theoretical and Experimental Optimization Application to High Speed Trains

SUMMARY

The literature concerned with road damage caused by heavy commercial vehicles is reviewed. The main types of vehicle-generated road damage are described and the methods that can be used to analyse them are presented. Attention is given to the principal features of the response of road surfaces to vehicle loads and mathematical models that have been developed to predict road response. Also discussed are those vehicle features which, to a first approximation, can be studied without consideration of the dynamics of the vehicle, including axle and tyre configurations, tyre contact conditions and static load sharing in axle group suspensions. The main emphasis of the paper is on the dynamic tyre forces generated by heavy vehicles: their principal characteristics, their simulation and measurement, the effects of suspension design on the forces and the methods that can be used to estimate their influence on road damage. Some critical research needs are identified.     

商用车双转向桥中间杆系优化设计

商用车双转向桥包含两个独立的转向梯形机构,它们之间的运动是通过中间杆系来传递的.在设计双转向桥转向系统时,为了避免转向桥轮胎异常磨损,需要两个转向桥的车轮转角协调变化.提出了一种对现有双转向桥中间杆系优化设计的方法,可协调车辆第一、第二转向桥的转角关系,避免了横向滑移导致的双前桥车轮转向时造成的轮胎异常磨损.     

Lateral dynamics of single unit skid-steered tracked vehicle

In the design and development of high-speed tracked vehicles, it is necessary to have an understanding of the interrelationship between the terrain factors and the vehicle characteristics during steering. The handling behavior of skid-steered tracked vehicles is more complex than that of wheeled vehicles because of non-linear characteristics arising from the sliding interface between the track and the ground. In the present work, a five degree-of-freedom (DOF) steering model of a tracked vehicle is developed, and the handling behavior during non-stationary motion is studied when operating at high and low speeds. It is demonstrated that the inclusion of roll and pitch DOF changes the steering response when compared to the response from three DOF models proposed earlier by several researchers. This is due to the strong coupling between the pitch and yaw motions. The effect of the initial forward velocities on the trajectory of the vehicle during non-stationary motion is also studied. It is observed from the results that the stability is influenced by the type of steering input, steering ratio and vehicle forward speed.     

Dynamic Behaviour of Ore Wagons in Curves at Malmbanan

The transportation of ore can be made more cost efficient by use of bigger and heavier trains. An increase in axle load is thereby wanted. The fleet of ore wagons of today at Malmbanan/Ofotbanan in northern Sweden and Norway has to be updated. It is of interest to find out if it is possible to allow a higher axle load on the track with new wagons

To be able to understand and predict the effects on track wear depending on what type of vehicle that is in use, the contact forces between wheels and rails have to be determined. A computer aided analysis has been made of the dynamic behaviour of three test vehicles equipped with different types of three-piece bogies running at Malmbanan. The vehicles are modelled and their interaction with the track is analysed using the multibody simulation package GENSYS

The simulations show that, even if the axle load is increased from 25 tons to 30 tons and the velocity is increased from 50 km/h to 60 km/h, it is possible to reduce lateral track forces and wear in curves by using a different bogie than the standard three-piece bogie used today.     

重型汽车低附着路面制动稳定性的仿真研究

文章利用trucksim重型汽车动力学仿真软件,对六轮双轴重型汽车在低附着路面左右车轮附着系数不一致情况下进行紧急制动的行驶工况进行了仿真研究。研究结果表明在低附着路面进行紧急制动时,对制动轮进行制动压力控制,有ABS控制的重型汽车比没有ABS控制的重型汽车具有更好地行驶稳定性。但在低附着路面上,有ABS控制的重型汽车比没有ABS控制的重型汽车的制动距离增加了很多,这对重型汽车的行车安全性非常不利。     

A study on model fidelity for model predictive control-based obstacle avoidance in high-speed autonomous ground vehicles

This paper investigates the level of model fidelity needed in order for a model predictive control (MPC)-based obstacle avoidance algorithm to be able to safely and quickly avoid obstacles even when the vehicle is close to its dynamic limits. The context of this work is large autonomous ground vehicles that manoeuvre at high speed within unknown, unstructured, flat environments and have significant vehicle dynamics-related constraints. Five different representations of vehicle dynamics models are considered: four variations of the two degrees-of-freedom (DoF) representation as lower fidelity models and a fourteen DoF representation with combined-slip Magic Formula tyre model as a higher fidelity model. It is concluded that the two DoF representation that accounts for tyre nonlinearities and longitudinal load transfer is necessary for the MPC-based obstacle avoidance algorithm in order to operate the vehicle at its limits within an environment that includes large obstacles. For less challenging environments, however, the two DoF representation with linear tyre model and constant axle loads is sufficient.     

Conceptual design of economic hybrid vehicle system using clutchless geared smart transmission

Most hybrid vehicles employ the continuously variable transmission (CVT or eCVT) currently as their choice of the transmissions. Recently, an automated geared transmission (AGT) or dual clutch transmission (DCT) is being tried for some hybrid vehicles for the better fuel economy than the CVT hybrid. However, this AGT or DCT is using automated clutches which require the hydraulic power in addition to the slippage in the clutch plate invoking some energy loss as well as wear. Also, they require a motor with significant power to match to the engine power. The clutchless geared smart transmission (CGST) has no clutch and the clutch function is performed by a planetary gear system controlled by a motor-generator. The hybrid vehicles proposed here using CGST may have some merits in durability, fuel efficiency, and cost since they do not have clutches. The motor used for the clutch function can be also working for power merge with the engine in propelling the vehicle. The proposed hybrid system can be either mild hybrid or full hybrid by adopting a different capacity of battery with much smaller motor-generator due to the planetary gear system compared to the other type hybrid vehicles. In this study, the prospects of newly proposed CGST hybrid system are examined in practical aspects compared with AGT hybrid or DCT hybrid systems.     

面向动态避障的智能汽车滚动时域路径规划

为解决城市低速条件下智能汽车在避障过程中的路径规划问题，提出面向动态避障的智能汽车滚动时域路径规划方法。首先，划分车道可行区域，利用3次拉格朗日插值法拟合车道边界，并根据"车-路"的相对位置关系将车道区域进一步划分为车道间区域与车道内区域两部分。其次，以区域虚拟力场进行动态交通场景模拟，包括在障碍车周身沿车道方向的虚拟矩形区域斥力场，行驶目标位置的虚拟引力场和车道保持虚拟区域引力场3个部分，然后结合划分的车道区域确定各虚拟力场的作用区域。再次，建立主车动力学与运动学模型，障碍车运动学预测模型，把主车与障碍车无碰撞，主车行驶在车道内区域，趋向目标位置以及保证车辆稳定性作为优化目标，综合车辆模型的控制输入、状态变量等动力学约束条件，构建多目标的滚动时域控制器用于车辆避障路径规划，求解获得前轮转角作为控制量。最后，利用MATLAB和veDYNA软件对提出的路径规划控制系统分别在静态障碍和动态障碍工况下进行联合仿真。研究结果表明：该方法能够很好地解决躲避静态障碍和低速动态障碍车的问题，控制车辆驶向目标位置，并且在避障过程中满足车辆的动力学约束，同时又不会与道路边界发生碰撞，保证了车辆的安全性和稳定性。     

Total dynamic response of a PSS vehicle negotiating asymmetric road excitations

A planar suspension system (PSS) is a novel automobile suspension system in which an individual spring–damper strut is implemented in both the vertical and longitudinal directions, respectively. The wheels in a vehicle with such a suspension system can move back and forth relative to the chassis. When a PSS vehicle experiences asymmetric road excitations, the relative longitudinal motion of wheels with respect to the chassis in two sides of the same axle are not identical, and thus the two wheels at one axle will not be aligned in the same axis. The total dynamic responses, including those of the bounce, pitch and the roll of the PSS vehicle, to the asymmetric road excitation may exhibit different characteristics from those of a conventional vehicle. This paper presents an investigation into the comprehensive dynamic behaviour of a vehicle with the PSS, in such a road condition, on both the straight and curved roads. The study was carried out using an 18 DOF full-car model incorporating a radial-spring tyre–ground contact model and a 2D tyre–ground dynamic friction model. Results demonstrate that the total dynamic behaviour of a PSS vehicle is generally comparable with that of the conventional vehicle, while PSS exhibits significant improvement in absorbing the impact forces along the longitudinal direction when compared to the conventional suspension system. The PSS vehicle is found to be more stable than the conventional vehicle in terms of the directional performance against the disturbance of the road potholes on a straight line manoeuvre, while exhibiting a very similar handling performance on a curved line.     

Power Requirements for Traversing Uneven Roadways

Vehicles which travel on uneven roadways or rough surfaces require power beyond that associated with air drag, rolling resistance or other sources of friction even though kinetic and potential energy may be conserved on the average. This is true because damped relative motions within the vehicle dissipate energy, and, even for nearly rigid vehicles, energy is lost at impact with the ground whenever the vehicle loses contact with the ground surface due to the finite downward acceleration of gravity.

Using elementary vehicle models, the nature and magnitude of the component of propulsive force associated with these energy loss mechanisms is estimated. In certain speed ranges, this force is found to vary dramatically with speed for several types of periodic roadway profiles studied. While the force due to unevennesss may be small compared to other forces for high-speed vehicles operating on smooth surfaces, it can be the major source of required power for off-road vehicles operating on very rough terrain.     

A Tractor Handling Study

Agricultural tractors are relatively slow moving vehicles but a good steer response under all working conditions is generally required. This paper evaluates the effect of ground slope, axle load, ground speed, tyres and ground surface on yaw rate response to steer input.     

Effect of number of wheels on high speed UGV traversability: Online terrain assessment approach

This paper addresses the problem of determining the maximum allowable speed (V _max ) of Unmanned Ground Vehicles (UGVs) traversing off-road heterogeneous rough/complex terrain. The maximum speed is calculated based on online terrain assessment and the vehicle’s characteristics; this speed achieves the high speed navigation without exceeding a predefined allowable range of transmitted force and moments (i.e., moments in the roll and pitch directions) to the vehicle’s frame. The proposed system enables UGV’s to change their speed autonomously and transit between terrains with different characteristics (e.g., pavement, rocky) safely. This paper proposes a computationally inexpensive approach to process acquired data and assess the terrain roughness. The proposed Roughness Index (RI) is used to represent the terrain roughness on a scale from 0.0 (highly rough to be traversed by a particular vehicle) to 1.0 (perfectly flat/smooth surface). A general vehicle model (workable for any vehicle size and wheel configuration) is presented in this paper. A closed form expression of the maximum allowable vehicle speed is developed. Simulation results obtained on real vehicles (e.g., military tank LEOPARD I) show the effect of increasing the number of wheels to improve the capability of a ground vehicle to traverse rough terrains at high speeds. In addition, the proposed terrain assessment system is a key module in UGVs navigation systems enabling them to be truly autonomous by providing the navigation system with the necessary information for path and speed planning.     

Overturning Stability of Three Wheeled Motorized Vehicles

Three wheeled motorized vehicles are a major mode of public transport in many countries. These vehicles are prone to overturning even during normal turning and obstacle avoidance maneuvers. This paper presents a parametric analysis of a mathematical model of the vehicle and evolves guidelines for improving the overturning stability in terms of vehicle geometry and suspension properties.

Differential equations governing the dynamic behavior of the vehicle are derived on the basis of a six degree of freedom model. The vehicle response to variations in steering, engine power and braking inputs is then numerically simulated. The effects of vehicle geometry and elasto-damping suspension coefficients on the vehicle stability are presented. The results indicate an optimum position of the center of gravity where the vehicle is most stable. While stiffer suspensions favour stability, there exists an optimum value of suspension damping for which the minimum wheel load is a maximum.